When printer_write() calls usb_ep_queue(), a udc driver (e.g.
renesas_usbhs driver) may call usb_gadget_giveback_request() in
the udc .queue ops immediately. Then, printer_write() calls
list_add(&req->list, &dev->tx_reqs_active) wrongly. After that,
if we do unbind the printer driver, WARN_ON() happens in
printer_func_unbind() because the list entry is not removed.
So, this patch moves list_add(&req->list, &dev->tx_reqs_active)
calling before usb_ep_queue().
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Driver currently crashes due to NULL pointer deference
while updating PHY tune register if nvmem cell is NULL.
Since, fused value for Tune1/2 register is optional,
we'd rather bail out.
Fixes: ca04d9d3e1b1 ("phy: qcom-qusb2: New driver for QUSB2 PHY on Qcom chips") Reviewed-by: Vivek Gautam <vivek.gautam@codeaurora.org> Reviewed-by: Evan Green <evgreen@chromium.org> Cc: stable <stable@vger.kernel.org> # 4.14+ Signed-off-by: Manu Gautam <mgautam@codeaurora.org> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The proposed patch adds compatibility quirks. Because the drive requires two
quirks (one to work with UAS, and another to work with usb-storage), adding this
under unusual_devs.h and not just unusual_uas.h so kernels compiled without UAS
receive the quirk. With the patch, the drive works reliably on UAS and usb-
storage.
(tested on NEC Corporation uPD720200 USB 3.0 host controller).
Signed-off-by: Alexander Kappner <agk@godking.net> Acked-by: Alan Stern <stern@rowland.harvard.edu> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The ALWAYS_SYNC flag is currently honored by the usb-storage driver but not UAS
and is required to work around devices that become unstable upon being
queried for cache. This code is taken straight from:
drivers/usb/storage/scsiglue.c:284
Signed-off-by: Alexander Kappner <agk@godking.net> Acked-by: Alan Stern <stern@rowland.harvard.edu> Cc: stable <stable@vger.kernel.org> Acked-by: Oliver Neukum <oneukum@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
pdev_nr and rhport can be controlled by user-space, hence leading to
a potential exploitation of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
drivers/usb/usbip/vhci_sysfs.c:238 detach_store() warn: potential spectre issue 'vhcis'
drivers/usb/usbip/vhci_sysfs.c:328 attach_store() warn: potential spectre issue 'vhcis'
drivers/usb/usbip/vhci_sysfs.c:338 attach_store() warn: potential spectre issue 'vhci->vhci_hcd_ss->vdev'
drivers/usb/usbip/vhci_sysfs.c:340 attach_store() warn: potential spectre issue 'vhci->vhci_hcd_hs->vdev'
Fix this by sanitizing pdev_nr and rhport before using them to index
vhcis and vhci->vhci_hcd_ss->vdev respectively.
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
It's amazing that this driver ever worked, but now that x86 doesn't
allow USB data to be sent off of the stack, it really does not work at
all. Fix this up by properly allocating the data for the small
"commands" that get sent to the device off of the stack.
We do this for one command by having a whole urb just for ack messages,
as they can be submitted in interrupt context, so we can not use
usb_bulk_msg(). But the poweron command can sleep (and does), so use
usb_bulk_msg() for that transfer.
Reported-by: Carlos Manuel Santos <cmmpsantos@gmail.com> Cc: Samuel Ortiz <sameo@linux.intel.com> Cc: Stephen Hemminger <stephen@networkplumber.org> Cc: stable <stable@vger.kernel.org> Reviewed-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
WARNING: CPU: 0 PID: 1467 at drivers/staging/android/ion/ion.c:122
ion_buffer_destroy+0xd4/0x190 drivers/staging/android/ion/ion.c:122
Kernel panic - not syncing: panic_on_warn set ...
This is catching that a buffer was freed with an existing kernel mapping
still present. This can be easily be triggered from userspace by calling
DMA_BUF_SYNC_START without calling DMA_BUF_SYNC_END. Switch to a single
pr_warn_once to indicate the error without being disruptive.
Reported-by: syzbot+cd8bcd40cb049efa2770@syzkaller.appspotmail.com Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: Laura Abbott <labbott@redhat.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Int the next patch the emulator's .read_std and .write_std callbacks will
grow another argument, which is not needed in kvm_read_guest_virt and
kvm_write_guest_virt_system's callers. Since we have to make separate
functions, let's give the currently existing names a nicer interface, too.
Fixes: 129a72a0d3c8 ("KVM: x86: Introduce segmented_write_std", 2017-01-12) Cc: stable@vger.kernel.org Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
MSB of CR3 is a reserved bit if the PCIDE bit is not set in CR4.
It should be checked when PCIDE bit is not set, however commit
'd1cd3ce900441 ("KVM: MMU: check guest CR3 reserved bits based on
its physical address width")' removes the bit 63 checking
unconditionally. This patch fixes it by checking bit 63 of CR3
when PCIDE bit is not set in CR4.
Fixes: d1cd3ce900441 (KVM: MMU: check guest CR3 reserved bits based on its physical address width) Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Radim Krčmář <rkrcmar@redhat.com> Cc: Liran Alon <liran.alon@oracle.com> Cc: stable@vger.kernel.org Reviewed-by: Junaid Shahid <junaids@google.com> Signed-off-by: Wanpeng Li <wanpengli@tencent.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Sometimes a GPIO is fetched with NULL as parent device, and
that is just fine. So under these circumstances, avoid using
dev_name() to provide a name for the GPIO line.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Cc: Daniel Rosenberg <drosen@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Key extensions (struct sadb_key) include a user-specified number of key
bits. The kernel uses that number to determine how much key data to copy
out of the message in pfkey_msg2xfrm_state().
The length of the sadb_key message must be verified to be long enough,
even in the case of SADB_X_AALG_NULL. Furthermore, the sadb_key_len value
must be long enough to include both the key data and the struct sadb_key
itself.
Introduce a helper function verify_key_len(), and call it from
parse_exthdrs() where other exthdr types are similarly checked for
correctness.
Signed-off-by: Kevin Easton <kevin@guarana.org> Reported-by: syzbot+5022a34ca5a3d49b84223653fab632dfb7b4cf37@syzkaller.appspotmail.com Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Cc: Zubin Mithra <zsm@chromium.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
When dealing with ingress rule on a netdev, if we did fine through the
conventional path, there's no need to continue into the egdev route,
and we can stop right there.
Not doing so may cause a 2nd rule to be added by the cls api layer
with the ingress being the egdev.
For example, under sriov switchdev scheme, a user rule of VFR A --> VFR B
will end up with two HW rules (1) VF A --> VF B and (2) uplink --> VF B
Fixes: 208c0f4b5237 ('net: sched: use tc_setup_cb_call to call per-block callbacks') Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
In the Broadcom Cygnus SoC, the brcm tag needs to be inserted
in between the mac address and the ether type (should use
'DSA_PROTO_TAG_BRCM') for the packets sent to the internal
b53 switch.
Since the Cygnus was added with the BCM58XX device id and the
BCM58XX uses 'DSA_PROTO_TAG_BRCM_PREPEND', the data path is
broken, due to the incorrect brcm tag location.
Add a new b53 device id (BCM583XX) for Cygnus family to fix the
issue. Add the new device id to the BCM58XX family as Cygnus
is similar to the BCM58XX in most other functionalities.
Fixes: 11606039604c ("net: dsa: b53: Support prepended Broadcom tags") Signed-off-by: Arun Parameswaran <arun.parameswaran@broadcom.com> Acked-by: Scott Branden <scott.branden@broadcom.com> Reported-by: Clément Péron <peron.clem@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Tested-by: Clément Péron <peron.clem@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The current error handling code has an issue where it does:
if (priv->txchan)
cpdma_chan_destroy(priv->txchan);
The problem is that ->txchan is either valid or an error pointer (which
would lead to an Oops). I've changed it to use multiple error labels so
that the test can be removed.
Also there were some missing calls to netif_napi_del().
Fixes: 3ef0fdb2342c ("net: davinci_emac: switch to new cpdma layer") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Ivan Khoronzhuk [Tue, 12 Dec 2017 21:06:35 +0000 (23:06 +0200)]
net: ethernet: ti: cpdma: correct error handling for chan create
BugLink: http://bugs.launchpad.net/bugs/1789666
It's not correct to return NULL when that is actually an error and
function returns errors in any other wrong case. In the same time,
the cpsw driver and davinci emac doesn't check error case while
creating channel and it can miss actual error. Also remove WARNs
replacing them on dev_err msgs.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org> Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
(cherry picked from commit 8a83c5d7969b8433584e3cf658a8d76c4dc37f4d) Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
VLAN 1 is internally used for untagged traffic. Prevent creation of
explicit netdevice for that VLAN, because that currently isn't supported
and leads to the NULL pointer dereference cited below.
Fix by preventing creation of VLAN devices with VID of 1 over mlxsw
devices or LAG devices that involve mlxsw devices.
Commit d02ba2a6110c ("l2tp: fix race in pppol2tp_release with session
object destroy") tried to fix a race condition where a PPPoL2TP socket
would disappear while the L2TP session was still using it. However, it
missed the root issue which is that an L2TP session may accept to be
reconnected if its associated socket has entered the release process.
The tentative fix makes the session hold the socket it is connected to.
That saves the kernel from crashing, but introduces refcount leakage,
preventing the socket from completing the release process. Once stalled,
everything the socket depends on can't be released anymore, including
the L2TP session and the l2tp_ppp module.
The root issue is that, when releasing a connected PPPoL2TP socket, the
session's ->sk pointer (RCU-protected) is reset to NULL and we have to
wait for a grace period before destroying the socket. The socket drops
the session in its ->sk_destruct callback function, so the session
will exist until the last reference on the socket is dropped.
Therefore, there is a time frame where pppol2tp_connect() may accept
reconnecting a session, as it only checks ->sk to figure out if the
session is connected. This time frame is shortened by the fact that
pppol2tp_release() calls l2tp_session_delete(), making the session
unreachable before resetting ->sk. However, pppol2tp_connect() may
grab the session before it gets unhashed by l2tp_session_delete(), but
it may test ->sk after the later got reset. The race is not so hard to
trigger and syzbot found a pretty reliable reproducer:
https://syzkaller.appspot.com/bug?id=418578d2a4389074524e04d641eacb091961b2cf
Before d02ba2a6110c, another race could let pppol2tp_release()
overwrite the ->__sk pointer of an L2TP session, thus tricking
pppol2tp_put_sk() into calling sock_put() on a socket that is different
than the one for which pppol2tp_release() was originally called. To get
there, we had to trigger the race described above, therefore having one
PPPoL2TP socket being released, while the session it is connected to is
reconnecting to a different PPPoL2TP socket. When releasing this new
socket fast enough, pppol2tp_release() overwrites the session's
->__sk pointer with the address of the new socket, before the first
pppol2tp_put_sk() call gets scheduled. Then the pppol2tp_put_sk() call
invoked by the original socket will sock_put() the new socket,
potentially dropping its last reference. When the second
pppol2tp_put_sk() finally runs, its socket has already been freed.
With d02ba2a6110c, the session takes a reference on both sockets.
Furthermore, the session's ->sk pointer is reset in the
pppol2tp_session_close() callback function rather than in
pppol2tp_release(). Therefore, ->__sk can't be overwritten and
pppol2tp_put_sk() is called only once (l2tp_session_delete() will only
run pppol2tp_session_close() once, to protect the session against
concurrent deletion requests). Now pppol2tp_put_sk() will properly
sock_put() the original socket, but the new socket will remain, as
l2tp_session_delete() prevented the release process from completing.
Here, we don't depend on the ->__sk race to trigger the bug. Getting
into the pppol2tp_connect() race is enough to leak the reference, no
matter when new socket is released.
So it all boils down to pppol2tp_connect() failing to realise that the
session has already been connected. This patch drops the unneeded extra
reference counting (mostly reverting d02ba2a6110c) and checks that
neither ->sk nor ->__sk is set before allowing a session to be
connected.
Fixes: d02ba2a6110c ("l2tp: fix race in pppol2tp_release with session object destroy") Signed-off-by: Guillaume Nault <g.nault@alphalink.fr> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Since we have the ttm and gem vma managers using a subset
of the file address space for objects, and these start at
0x100000000 they will overflow the new mmap checks.
I've checked all the mmap routines I could see for any
bad behaviour but overall most people use GEM/TTM VMA
managers even the legacy drivers have a hashtable.
Reported-and-Tested-by: Arthur Marsh (amarsh04 on #radeon) Fixes: be83bbf8068 (mmap: introduce sane default mmap limits) Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Before the guest finishes the device initialization, the device can be
removed anytime by the host, and after that the host won't respond to
the guest's request, so the guest should be prepared to handle this
case.
Add a polling mechanism to detect device presence.
Signed-off-by: Dexuan Cui <decui@microsoft.com>
[lorenzo.pieralisi@arm.com: edited commit log] Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com> Cc: Stephen Hemminger <sthemmin@microsoft.com> Cc: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
It seems that rtnl_group_changelink() can call do_setlink
while a prior call to validate_linkmsg(dev = NULL, ...) could
not validate IFLA_ADDRESS / IFLA_BROADCAST
Make sure do_setlink() calls validate_linkmsg() instead
of letting its callers having this responsibility.
We need to drop refcnt to xdp_page if we see a gso packet. Otherwise
it will be leaked. Fixing this by moving the check of gso packet above
the linearizing logic. While at it, remove useless comment as well.
Cc: John Fastabend <john.fastabend@gmail.com> Fixes: 72979a6c3590 ("virtio_net: xdp, add slowpath case for non contiguous buffers") Signed-off-by: Jason Wang <jasowang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
If we successfully linearize the packet, num_buf will be set to zero
which may confuse error handling path which assumes num_buf is at
least 1 and this can lead the code tries to pop the descriptor of next
buffer. Fixing this by checking num_buf against 1 before decreasing.
Fixes: 4941d472bf95 ("virtio-net: do not reset during XDP set") Signed-off-by: Jason Wang <jasowang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Calling XDP redirection requires bh disabled. Softirq can call another
XDP function and redirection functions, then the percpu static variable
ri->map can be overwritten to NULL.
v2:
- Removed preempt_disable/enable since local_bh_disable will prevent
preemption as well, feedback from Jason Wang.
Fixes: 761876c857cb ("tap: XDP support") Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp> Acked-by: Jason Wang <jasowang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
spin_lock/unlock was used instead of spin_un/lock_irq
in a procedure used in process space, on a spinlock
which can be grabbed in an interrupt.
This caused the stack trace below to be displayed (on kernel
4.17.0-rc1 compiled with Lock Debugging enabled):
[ 154.661474] WARNING: SOFTIRQ-safe -> SOFTIRQ-unsafe lock order detected
[ 154.668909] 4.17.0-rc1-rdma_rc_mlx+ #3 Tainted: G I
[ 154.675856] -----------------------------------------------------
[ 154.682706] modprobe/10159 [HC0[0]:SC0[0]:HE0:SE1] is trying to acquire:
[ 154.690254] 00000000f3b0e495 (&(&qp_table->lock)->rlock){+.+.}, at: mlx4_qp_remove+0x20/0x50 [mlx4_core]
[ 154.700927]
and this task is already holding:
[ 154.707461] 0000000094373b5d (&(&cq->lock)->rlock/1){....}, at: destroy_qp_common+0x111/0x560 [mlx4_ib]
[ 154.718028] which would create a new lock dependency:
[ 154.723705] (&(&cq->lock)->rlock/1){....} -> (&(&qp_table->lock)->rlock){+.+.}
[ 154.731922]
but this new dependency connects a SOFTIRQ-irq-safe lock:
[ 154.740798] (&(&cq->lock)->rlock){..-.}
[ 154.740800]
... which became SOFTIRQ-irq-safe at:
[ 154.752163] _raw_spin_lock_irqsave+0x3e/0x50
[ 154.757163] mlx4_ib_poll_cq+0x36/0x900 [mlx4_ib]
[ 154.762554] ipoib_tx_poll+0x4a/0xf0 [ib_ipoib]
...
to a SOFTIRQ-irq-unsafe lock:
[ 154.815603] (&(&qp_table->lock)->rlock){+.+.}
[ 154.815604]
... which became SOFTIRQ-irq-unsafe at:
[ 154.827718] ...
[ 154.827720] _raw_spin_lock+0x35/0x50
[ 154.833912] mlx4_qp_lookup+0x1e/0x50 [mlx4_core]
[ 154.839302] mlx4_flow_attach+0x3f/0x3d0 [mlx4_core]
Since mlx4_qp_lookup() is called only in process space, we can
simply replace the spin_un/lock calls with spin_un/lock_irq calls.
Fixes: 6dc06c08bef1 ("net/mlx4: Fix the check in attaching steering rules") Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
We should not go for the error path after successfully transmitting a
XDP buffer after linearizing. Since the error path may try to pop and
drop next packet and increase the drop counters. Fixing this by simply
drop the refcnt of original page and go for xmit path.
Fixes: 72979a6c3590 ("virtio_net: xdp, add slowpath case for non contiguous buffers") Cc: John Fastabend <john.fastabend@gmail.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Jason Wang <jasowang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
This patch reorders the error cases in showing the XPS configuration so
that we hold off on memory allocation until after we have verified that we
can support XPS on a given ring.
Fixes: 184c449f91fe ("net: Add support for XPS with QoS via traffic classes") Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
We are currently doing auxiliary control register reads with the shadow
register value 0b111 (0x7) which incidentally is also the selector value
that should be present in bits [2:0]. Fix this by using the appropriate
selector mask which is defined (MII_BCM54XX_AUXCTL_SHDWSEL_MASK).
This does not have a functional impact yet because we always access the
MII_BCM54XX_AUXCTL_SHDWSEL_MISC (0x7) register in the current code.
This might change at some point though.
Fixes: 5b4e29005123 ("net: phy: broadcom: add bcm54xx_auxctl_read") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
seg6_do_srh_encap and seg6_do_srh_inline can possibly do an
out-of-bounds access when adding the SRH to the packet. This no longer
happen when expanding the skb not only by the size of the SRH (+
outer IPv6 header), but also by skb->mac_len.
[ 53.793056] BUG: KASAN: use-after-free in seg6_do_srh_encap+0x284/0x620
[ 53.794564] Write of size 14 at addr ffff88011975ecfa by task ping/674
Fixes: 6c8702c60b88 ("ipv6: sr: add support for SRH encapsulation and injection with lwtunnels") Signed-off-by: David Lebrun <dlebrun@google.com> Signed-off-by: Mathieu Xhonneux <m.xhonneux@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Use the right device to determine if redirect should be sent especially
when using vrf. Same as well as when sending the redirect.
Signed-off-by: Stephen Suryaputra <ssuryaextr@gmail.com> Acked-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
DaeRyong Jeong reports a race between vhost_dev_cleanup() and
vhost_process_iotlb_msg():
Thread interleaving:
CPU0 (vhost_process_iotlb_msg) CPU1 (vhost_dev_cleanup)
(In the case of both VHOST_IOTLB_UPDATE and
VHOST_IOTLB_INVALIDATE)
===== =====
vhost_umem_clean(dev->iotlb);
if (!dev->iotlb) {
ret = -EFAULT;
break;
}
dev->iotlb = NULL;
The reason is we don't synchronize between them, fixing by protecting
vhost_process_iotlb_msg() with dev mutex.
Reported-by: DaeRyong Jeong <threeearcat@gmail.com> Fixes: 6b1e6cc7855b0 ("vhost: new device IOTLB API") Signed-off-by: Jason Wang <jasowang@redhat.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
This code was introduced in 2011 around the same time that we made
netdev_features_t a u64 type. These days a u32 is not big enough to
hold all the potential features.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
syzbot reported a rcu_sched self-detected stall on CPU which is caused
by too small value set on rto_min with SCTP_RTOINFO sockopt. With this
value, hb_timer will get stuck there, as in its timer handler it starts
this timer again with this value, then goes to the timer handler again.
This problem is there since very beginning, and thanks to Eric for the
reproducer shared from a syzbot mail.
This patch fixes it by not allowing sctp_transport_timeout to return a
smaller value than HZ/5 for hb_timer, which is based on TCP's min rto.
Note that it doesn't fix this issue by limiting rto_min, as some users
are still using small rto and no proper value was found for it yet.
Reported-by: syzbot+3dcd59a1f907245f891f@syzkaller.appspotmail.com Suggested-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
ILT entry requires 12 bit right shifted physical address.
Existing mask for ILT entry of physical address i.e.
ILT_ENTRY_PHY_ADDR_MASK is not sufficient to handle 64bit
address because upper 8 bits of 64 bit address were getting
masked which resulted in completer abort error on
PCIe bus due to invalid address.
Fix that mask to handle 64bit physical address.
Fixes: fe56b9e6a8d9 ("qed: Add module with basic common support") Signed-off-by: Shahed Shaikh <shahed.shaikh@cavium.com> Signed-off-by: Ariel Elior <ariel.elior@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Commit b84bbaf7a6c8 ("packet: in packet_snd start writing at link
layer allocation") ensures that packet_snd always starts writing
the link layer header in reserved headroom allocated for this
purpose.
This is needed because packets may be shorter than hard_header_len,
in which case the space up to hard_header_len may be zeroed. But
that necessary padding is not accounted for in skb->len.
The fix, however, is buggy. It calls skb_push, which grows skb->len
when moving skb->data back. But in this case packet length should not
change.
Instead, call skb_reserve, which moves both skb->data and skb->tail
back, without changing length.
Fixes: b84bbaf7a6c8 ("packet: in packet_snd start writing at link layer allocation") Reported-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: Willem de Bruijn <willemb@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Testing Telit LM940 with ICMP packets > 14552 bytes revealed that
the modem needs FLAG_SEND_ZLP to properly work, otherwise the cdc
mbim data interface won't be anymore responsive.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com> Acked-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
On newer PHYs, we need to select the expansion register to write with
setting bits [11:8] to 0xf. This was done correctly by bcm7xxx.c prior
to being migrated to generic code under bcm-phy-lib.c which
unfortunately used the older implementation from the BCM54xx days.
Fix this by creating an inline stub: bcm_write_exp_sel() which adds the
correct value (MII_BCM54XX_EXP_SEL_ER) and update both the Cygnus PHY
and BCM7xxx PHY drivers which require setting these bits.
broadcom.c is unchanged because some PHYs even use a different selector
method, so let them specify it directly (e.g: SerDes secondary selector).
Fixes: a1cba5613edf ("net: phy: Add Broadcom phy library for common interfaces") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Various commits tried to address the problem in the past,
but failed to take into account V3 header size.
[1]
tpacket_rcv: packet too big, clamped from 72 to 4294967224. macoff=96
BUG: KASAN: use-after-free in prb_run_all_ft_ops net/packet/af_packet.c:1016 [inline]
BUG: KASAN: use-after-free in prb_fill_curr_block.isra.59+0x4e5/0x5c0 net/packet/af_packet.c:1039
Write of size 2 at addr ffff8801cb62000e by task kworker/1:2/2106
Fixes: 2b6867c2ce76 ("net/packet: fix overflow in check for priv area size") Fixes: dc808110bb62 ("packet: handle too big packets for PACKET_V3") Fixes: f6fb8f100b80 ("af-packet: TPACKET_V3 flexible buffer implementation.") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Per discussion with David at netconf 2018, let's clarify
DaveM's position of handling stable backports in netdev-FAQ.
This is important for people relying on upstream -stable
releases.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
kcm_clone() creates kernel socket, which does not take net counter.
Thus, the net may die before the socket is completely destructed,
i.e. kcm_exit_net() is executed before kcm_done().
Reported-by: syzbot+5f1a04e374a635efc426@syzkaller.appspotmail.com Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
In divasmain.c, the function divas_write() firstly invokes the function
diva_xdi_open_adapter() to open the adapter that matches with the adapter
number provided by the user, and then invokes the function diva_xdi_write()
to perform the write operation using the matched adapter. The two functions
diva_xdi_open_adapter() and diva_xdi_write() are located in diva.c.
In diva_xdi_open_adapter(), the user command is copied to the object 'msg'
from the userspace pointer 'src' through the function pointer 'cp_fn',
which eventually calls copy_from_user() to do the copy. Then, the adapter
number 'msg.adapter' is used to find out a matched adapter from the
'adapter_queue'. A matched adapter will be returned if it is found.
Otherwise, NULL is returned to indicate the failure of the verification on
the adapter number.
As mentioned above, if a matched adapter is returned, the function
diva_xdi_write() is invoked to perform the write operation. In this
function, the user command is copied once again from the userspace pointer
'src', which is the same as the 'src' pointer in diva_xdi_open_adapter() as
both of them are from the 'buf' pointer in divas_write(). Similarly, the
copy is achieved through the function pointer 'cp_fn', which finally calls
copy_from_user(). After the successful copy, the corresponding command
processing handler of the matched adapter is invoked to perform the write
operation.
It is obvious that there are two copies here from userspace, one is in
diva_xdi_open_adapter(), and one is in diva_xdi_write(). Plus, both of
these two copies share the same source userspace pointer, i.e., the 'buf'
pointer in divas_write(). Given that a malicious userspace process can race
to change the content pointed by the 'buf' pointer, this can pose potential
security issues. For example, in the first copy, the user provides a valid
adapter number to pass the verification process and a valid adapter can be
found. Then the user can modify the adapter number to an invalid number.
This way, the user can bypass the verification process of the adapter
number and inject inconsistent data.
This patch reuses the data copied in
diva_xdi_open_adapter() and passes it to diva_xdi_write(). This way, the
above issues can be avoided.
Signed-off-by: Wenwen Wang <wang6495@umn.edu> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Some of the code paths calculating flow hash for IPv6 use flowlabel member
of struct flowi6 which, despite its name, encodes both flow label and
traffic class. If traffic class changes within a TCP connection (as e.g.
ssh does), ECMP route can switch between path. It's also inconsistent with
other code paths where ip6_flowlabel() (returning only flow label) is used
to feed the key.
Use only flow label everywhere, including one place where hash key is set
using ip6_flowinfo().
Fixes: 51ebd3181572 ("ipv6: add support of equal cost multipath (ECMP)") Fixes: f70ea018da06 ("net: Add functions to get skb->hash based on flow structures") Signed-off-by: Michal Kubecek <mkubecek@suse.cz> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
A precondition check in ip_recv_error triggered on an otherwise benign
race. Remove the warning.
The warning triggers when passing an ipv6 socket to this ipv4 error
handling function. RaceFuzzer was able to trigger it due to a race
in setsockopt IPV6_ADDRFORM.
This socket option converts a v6 socket that is connected to a v4 peer
to an v4 socket. It updates the socket on the fly, changing fields in
sk as well as other structs. This is inherently non-atomic. It races
with the lockless udp_recvmsg path.
No other code makes an assumption that these fields are updated
atomically. It is benign here, too, as ip_recv_error cares only about
the protocol of the skbs enqueued on the error queue, for which
sk_family is not a precise predictor (thanks to another isue with
IPV6_ADDRFORM).
Link: http://lkml.kernel.org/r/20180518120826.GA19515@dragonet.kaist.ac.kr Fixes: 7ce875e5ecb8 ("ipv4: warn once on passing AF_INET6 socket to ip_recv_error") Reported-by: DaeRyong Jeong <threeearcat@gmail.com> Suggested-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Fixes: 8fb472c09b9d ("ipmr: improve hash scalability") Fixes: 0bbbf0e7d0e7 ("ipmr, ip6mr: Unite creation of new mr_table") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Cc: Yuval Mintz <yuvalm@mellanox.com> Reported-by: syzbot <syzkaller@googlegroups.com> Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
I don't know where this value comes from (probably a copy and paste and
paste and paste ...).
Let's use standard values which are a bit greater.
Link: https://git.kernel.org/pub/scm/linux/kernel/git/davem/netdev-vger-cvs.git/commit/?id=e5afd356a411a Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Currently, raw6_sk(sk)->ip6mr_table is set unconditionally during
ip6_mroute_setsockopt(MRT6_TABLE). A subsequent attempt at the same
setsockopt will fail with -ENOENT, since we haven't actually created
that table.
A similar fix for ipv4 was included in commit 5e1859fbcc3c ("ipv4: ipmr:
various fixes and cleanups").
Fixes: d1db275dd3f6 ("ipv6: ip6mr: support multiple tables") Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
In commit 624dbf55a359b ("driver/net: enic: Try DMA 64 first, then
failover to DMA") DMA mask was changed from 40 bits to 64 bits.
Hardware actually supports only 47 bits.
Fixes: 624dbf55a359b ("driver/net: enic: Try DMA 64 first, then failover to DMA") Signed-off-by: Govindarajulu Varadarajan <gvaradar@cisco.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Syzbot reported the use-after-free in timer_is_static_object() [1].
This can happen because the structure for the rto timer (ccid2_hc_tx_sock)
is removed in dccp_disconnect(), and ccid2_hc_tx_rto_expire() can be
called after that.
The report [1] is similar to the one in commit 120e9dabaf55 ("dccp:
defer ccid_hc_tx_delete() at dismantle time"). And the fix is the same,
delay freeing ccid2_hc_tx_sock structure, so that it is freed in
dccp_sk_destruct().
[1]
==================================================================
BUG: KASAN: use-after-free in timer_is_static_object+0x80/0x90
kernel/time/timer.c:607
Read of size 8 at addr ffff8801bebb5118 by task syz-executor2/25299
Reported-by: syzbot+5d47e9ec91a6f15dbd6f@syzkaller.appspotmail.com Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Nearby code that also tests port suggests that the P0 constant should be
used when port is zero.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e,e1;
@@
* e ? e1 : e1
// </smpl>
Fixes: 6c3218c6f7e5 ("bnx2x: Adjust ETS to 578xx") Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
In file included from scripts/kconfig/zconf.tab.c:2485:
scripts/kconfig/confdata.c: In function ‘conf_write’:
scripts/kconfig/confdata.c:773:22: warning: ‘%s’ directive writing likely 7 or more bytes into a region of size between 1 and 4097 [-Wformat-overflow=]
sprintf(newname, "%s%s", dirname, basename);
^~
scripts/kconfig/confdata.c:773:19: note: assuming directive output of 7 bytes
sprintf(newname, "%s%s", dirname, basename);
^~~~~~
scripts/kconfig/confdata.c:773:2: note: ‘sprintf’ output 1 or more bytes (assuming 4104) into a destination of size 4097
sprintf(newname, "%s%s", dirname, basename);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
scripts/kconfig/confdata.c:776:23: warning: ‘.tmpconfig.’ directive writing 11 bytes into a region of size between 1 and 4097 [-Wformat-overflow=]
sprintf(tmpname, "%s.tmpconfig.%d", dirname, (int)getpid());
^~~~~~~~~~~
scripts/kconfig/confdata.c:776:3: note: ‘sprintf’ output between 13 and 4119 bytes into a destination of size 4097
sprintf(tmpname, "%s.tmpconfig.%d", dirname, (int)getpid());
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Increase the size of tmpname and newname to make GCC happy.
Commit be83bbf80682 ("mmap: introduce sane default mmap limits") was
introduced to catch problems in various ad-hoc character device drivers
doing mmap and getting the size limits wrong. In the process, it used
"known good" limits for the normal cases of mapping regular files and
block device drivers.
It turns out that the "s_maxbytes" limit was less "known good" than I
thought. In particular, /proc doesn't set it, but exposes one regular
file to mmap: /proc/vmcore. As a result, that file got limited to the
default MAX_INT s_maxbytes value.
This went unnoticed for a while, because apparently the only thing that
needs it is the s390 kernel zfcpdump, but there might be other tools
that use this too.
Vasily suggested just changing s_maxbytes for all of /proc, which isn't
wrong, but makes me nervous at this stage. So instead, just make the
new mmap limit always be MAX_LFS_FILESIZE for regular files, which won't
affect anything else. It wasn't the regular file case I was worried
about.
I'd really prefer for maxsize to have been per-inode, but that is not
how things are today.
The internal VM "mmap()" interfaces are based on the mmap target doing
everything using page indexes rather than byte offsets, because
traditionally (ie 32-bit) we had the situation that the byte offset
didn't fit in a register. So while the mmap virtual address was limited
by the word size of the architecture, the backing store was not.
So we're basically passing "pgoff" around as a page index, in order to
be able to describe backing store locations that are much bigger than
the word size (think files larger than 4GB etc).
But while this all makes a ton of sense conceptually, we've been dogged
by various drivers that don't really understand this, and internally
work with byte offsets, and then try to work with the page index by
turning it into a byte offset with "pgoff << PAGE_SHIFT".
Which obviously can overflow.
Adding the size of the mapping to it to get the byte offset of the end
of the backing store just exacerbates the problem, and if you then use
this overflow-prone value to check various limits of your device driver
mmap capability, you're just setting yourself up for problems.
The correct thing for drivers to do is to do their limit math in page
indices, the way the interface is designed. Because the generic mmap
code _does_ test that the index doesn't overflow, since that's what the
mmap code really cares about.
HOWEVER.
Finding and fixing various random drivers is a sisyphean task, so let's
just see if we can just make the core mmap() code do the limiting for
us. Realistically, the only "big" backing stores we need to care about
are regular files and block devices, both of which are known to do this
properly, and which have nice well-defined limits for how much data they
can access.
So let's special-case just those two known cases, and then limit other
random mmap users to a backing store that still fits in "unsigned long".
Realistically, that's not much of a limit at all on 64-bit, and on
32-bit architectures the only worry might be the GPU drivers, which can
have big physical address spaces.
To make it possible for drivers like that to say that they are 64-bit
clean, this patch does repurpose the "FMODE_UNSIGNED_OFFSET" bit in the
file flags to allow drivers to mark their file descriptors as safe in
the full 64-bit mmap address space.
[ The timing for doing this is less than optimal, and this should really
go in a merge window. But realistically, this needs wide testing more
than it needs anything else, and being main-line is the only way to do
that.
So the earlier the better, even if it's outside the proper development
cycle - Linus ]
Cc: Kees Cook <keescook@chromium.org> Cc: Dan Carpenter <dan.carpenter@oracle.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Willy Tarreau <w@1wt.eu> Cc: Dave Airlie <airlied@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Since SCSI scanning occurs asynchronously, since sd_revalidate_disk() is
called from sd_probe_async() and since sd_revalidate_disk() calls
sd_zbc_read_zones() it can happen that sd_zbc_read_zones() is called
concurrently with blkdev_report_zones() and/or blkdev_reset_zones(). That can
cause these functions to fail with -EIO because sd_zbc_read_zones() e.g. sets
q->nr_zones to zero before restoring it to the actual value, even if no drive
characteristics have changed. Avoid that this can happen by making the
following changes:
- Protect the code that updates zone information with blk_queue_enter()
and blk_queue_exit().
- Modify sd_zbc_setup_seq_zones_bitmap() and sd_zbc_setup() such that
these functions do not modify struct scsi_disk before all zone
information has been obtained.
Note: since commit 055f6e18e08f ("block: Make q_usage_counter also track
legacy requests"; kernel v4.15) the request queue freezing mechanism also
affects legacy request queues.
Fixes: 89d947561077 ("sd: Implement support for ZBC devices") Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Damien Le Moal <damien.lemoal@wdc.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Hannes Reinecke <hare@suse.com> Cc: stable@vger.kernel.org # v4.16 Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
... into a global, two-dimensional array and service subsequent reads from
that cache to avoid rdmsr_on_cpu() calls during CPU hotplug (IPIs with IRQs
disabled).
In addition, this fixes a KASAN slab-out-of-bounds read due to wrong usage
of the bank->blocks pointer.
Fixes: 27bd59502702 ("x86/mce/AMD: Get address from already initialized block") Reported-by: Johannes Hirte <johannes.hirte@datenkhaos.de> Tested-by: Johannes Hirte <johannes.hirte@datenkhaos.de> Signed-off-by: Borislav Petkov <bp@suse.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Yazen Ghannam <yazen.ghannam@amd.com> Link: http://lkml.kernel.org/r/20180414004230.GA2033@probook Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Yazen Ghannam [Wed, 21 Feb 2018 10:18:58 +0000 (11:18 +0100)]
x86/mce/AMD, EDAC/mce_amd: Enumerate Reserved SMCA bank type
BugLink: http://bugs.launchpad.net/bugs/1788897
Currently, bank 4 is reserved on Fam17h, so we chose not to initialize
bank 4 in the smca_banks array. This means that when we check if a bank
is initialized, like during boot or resume, we will see that bank 4 is
not initialized and try to initialize it.
This will cause a call trace, when resuming from suspend, due to
rdmsr_*on_cpu() calls in the init path. The rdmsr_*on_cpu() calls issue
an IPI but we're running with interrupts disabled. This triggers:
WARNING: CPU: 0 PID: 11523 at kernel/smp.c:291 smp_call_function_single+0xdc/0xe0
...
Reserved banks will be read-as-zero, so their MCA_IPID register will be
zero. So, like the smca_banks array, the threshold_banks array will not
have an entry for a reserved bank since all its MCA_MISC* registers will
be zero.
Enumerate a "Reserved" bank type that matches on a HWID_MCATYPE of 0,0.
Use the "Reserved" type when checking if a bank is reserved. It's
possible that other bank numbers may be reserved on future systems.
Don't try to find the block address on reserved banks.
Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com> Signed-off-by: Borislav Petkov <bp@suse.de> Cc: <stable@vger.kernel.org> # 4.14.x Cc: Borislav Petkov <bp@alien8.de> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Tony Luck <tony.luck@intel.com> Cc: linux-edac <linux-edac@vger.kernel.org> Link: http://lkml.kernel.org/r/20180221101900.10326-7-bp@alien8.de Signed-off-by: Ingo Molnar <mingo@kernel.org>
(cherry picked from commit 68627a697c195937672ce07683094c72b1174786) Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Also, we should compare the bank number to MAX_NR_BANKS (size of the
smca_banks array) not the number of bank types. Bank types are reused
for multiple banks, so the number of types can be different from the
number of banks in a system and thus we could return an invalid bank
type.
Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com> Signed-off-by: Borislav Petkov <bp@suse.de> Cc: <stable@vger.kernel.org> # 4.14.x Cc: <stable@vger.kernel.org> # 4.14.x: 11cf887728a3 x86/MCE/AMD: Define a function to get SMCA bank type Cc: <stable@vger.kernel.org> # 4.14.x: c6708d50f166 x86/MCE: Report only DRAM ECC as memory errors on AMD systems Cc: Borislav Petkov <bp@alien8.de> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Tony Luck <tony.luck@intel.com> Cc: linux-edac <linux-edac@vger.kernel.org> Link: http://lkml.kernel.org/r/20180221101900.10326-6-bp@alien8.de Signed-off-by: Ingo Molnar <mingo@kernel.org>
(cherry picked from commit e5d6a126d4c473499f354254a15ca0c2d8c84ca3) Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Yazen Ghannam [Mon, 18 Dec 2017 11:37:12 +0000 (12:37 +0100)]
x86/MCE/AMD: Define a function to get SMCA bank type
BugLink: http://bugs.launchpad.net/bugs/1788897
Scalable MCA systems have various types of banks. The bank's type
can determine how we handle errors from it. For example, if a bank
represents a UMC (Unified Memory Controller) then we will need to
convert its address from a normalized address to a system physical
address before handling the error.
[ bp: Verify m->bank is within range and use bank pointer. ]
Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com> Signed-off-by: Borislav Petkov <bp@suse.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/20171207203955.118171-1-Yazen.Ghannam@amd.com Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
hid_sensor_set_power_work() powers the sensors back up after a resume
based on the user_requested_state atomic_t.
But hid_sensor_power_state() treats this as a boolean flag, leading to
the following problematic scenario:
1) Some app starts using the iio-sensor in buffered / triggered mode,
hid_sensor_data_rdy_trigger_set_state(true) gets called, setting
user_requested_state to 1.
2) Something directly accesses a _raw value through sysfs, leading
to a call to hid_sensor_power_state(true) followed by
hid_sensor_power_state(false) call, this sets user_requested_state
to 1 followed by setting it to 0.
3) Suspend/resume the machine, hid_sensor_set_power_work() now does
NOT power the sensor back up because user_requested_state (wrongly)
is 0. Which stops the app using the sensor in buffered mode from
receiving any new values.
This commit changes user_requested_state to a counter tracking how many
times hid_sensor_power_state(true) was called instead, fixing this.
Cc: Bastien Nocera <hadess@hadess.net> Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Use kasprintf instead of combination of kmalloc and sprintf. Also,
remove the local variables used for storing the string length as they
are not required now.
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com> Reviewed-by: Sinclair Yeh <syeh@vmware.com> Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Delay registering ourselves with the acpi lid notification mechanism
until we are registering the connectors after initialisation is
complete. This prevents a possibility of trying to handle the lid
notification before we are ready with the danger of chasing
uninitialised function pointers.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=106559 Fixes: c1c7af608920 ("drm/i915: force mode set at lid open time") Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Reviewed-by: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180518074840.16194-1-chris@chris-wilson.co.uk Cc: stable@vger.kernel.org
(cherry picked from commit e578a570dc7c20475774d1ff993825e3bd7a7011) Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Entry corresponding to 220 us setup time was missing. I am not aware of
any specific bug this fixes, but this could potentially result in enabling
PSR on a panel with a higher setup time requirement than supported by the
hardware.
I verified the value is present in eDP spec versions 1.3, 1.4 and 1.4a.
Fixes: 6608804b3d7f ("drm/dp: Add drm_dp_psr_setup_time()") Cc: stable@vger.kernel.org Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Jose Roberto de Souza <jose.souza@intel.com> Cc: dri-devel@lists.freedesktop.org Reviewed-by: José Roberto de Souza <jose.souza@intel.com> Reviewed-by: Tarun Vyas <tarun.vyas@intel.com> Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180511195145.3829-3-dhinakaran.pandiyan@intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Commit d5c435df4a890 ("intel_th: msu: Use the real device in case of IOMMU
domain allocation") changes dma buffer allocation to use the actual
underlying device, but forgets to change the deallocation path, which leads
to (if you've got CAP_SYS_RAWIO):
> # echo 0,0 > /sys/bus/intel_th/devices/0-msc0/nr_pages
> ------------[ cut here ]------------
> kernel BUG at ../linux/drivers/iommu/intel-iommu.c:3670!
> CPU: 3 PID: 231 Comm: sh Not tainted 4.17.0-rc1+ #2729
> RIP: 0010:intel_unmap+0x11e/0x130
...
> Call Trace:
> intel_free_coherent+0x3e/0x60
> msc_buffer_win_free+0x100/0x160 [intel_th_msu]
This patch fixes the buffer deallocation code to use the correct device.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Fixes: d5c435df4a890 ("intel_th: msu: Use the real device in case of IOMMU domain allocation") Reported-by: Baofeng Tian <baofeng.tian@intel.com> CC: stable@vger.kernel.org # v4.14+ Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
In some situations when we set TXOP_BACKOFF, the probe frame is
not sent at all. What it worse then sending probe frame as part
of AMPDU and can degrade 11n performance to 11g rates.
Cc: stable@vger.kernel.org Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Swapping load on huge=always tmpfs (with khugepaged tuned up to be very
eager, but I'm not sure that is relevant) soon hung uninterruptibly,
waiting for page lock in shmem_getpage_gfp()'s find_lock_entry(), most
often when "cp -a" was trying to write to a smallish file. Debug showed
that the page in question was not locked, and page->mapping NULL by now,
but page->index consistent with having been in a huge page before.
Reproduced in minutes on a 4.15 kernel, even with 4.17's 605ca5ede764
("mm/huge_memory.c: reorder operations in __split_huge_page_tail()") added
in; but took hours to reproduce on a 4.17 kernel (no idea why).
The culprit proved to be the __ClearPageDirty() on tails beyond i_size in
__split_huge_page(): the non-atomic __bitoperation may have been safe when
4.8's baa355fd3314 ("thp: file pages support for split_huge_page()")
introduced it, but liable to erase PageWaiters after 4.10's 62906027091f
("mm: add PageWaiters indicating tasks are waiting for a page bit").
Link: http://lkml.kernel.org/r/alpine.LSU.2.11.1805291841070.3197@eggly.anvils Fixes: 62906027091f ("mm: add PageWaiters indicating tasks are waiting for a page bit") Signed-off-by: Hugh Dickins <hughd@google.com> Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
When a GID entry is invalid EAGAIN is returned. This is an incorrect error
code, there is nothing that will make this GID entry valid again in
bounded time.
Some user space tools fail incorrectly if EAGAIN is returned here, and
this represents a small ABI change from earlier kernels.
The first patch in the Fixes list makes entries that were valid before
to become invalid, allowing this code to trigger, while the second patch
in the Fixes list introduced the wrong EAGAIN.
Therefore revert the return result to EINVAL which matches the historical
expectations of the ibv_query_gid_type() API of the libibverbs user space
library.
Cc: <stable@vger.kernel.org> Fixes: 598ff6bae689 ("IB/core: Refactor GID modify code for RoCE") Fixes: 03db3a2d81e6 ("IB/core: Add RoCE GID table management") Reviewed-by: Daniel Jurgens <danielj@mellanox.com> Signed-off-by: Parav Pandit <parav@mellanox.com> Signed-off-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Commit b5e2ced9bf81 ("stm class: Use vmalloc for the master map") caused
a build error on some arches as vmalloc.h was not explicitly included.
Fix that by adding it to the list of includes.
Fixes: b5e2ced9bf81 ("stm class: Use vmalloc for the master map") Reported-by: kbuild test robot <lkp@intel.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Fengguang is running into a warning from the buddy allocator:
> swapper/0: page allocation failure: order:9, mode:0x14040c0(GFP_KERNEL|__GFP_COMP), nodemask=(null)
> CPU: 1 PID: 1 Comm: swapper/0 Not tainted 4.17.0-rc1 #262
> Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1 04/01/2014
> Call Trace:
...
> __kmalloc+0x14b/0x180: ____cache_alloc at mm/slab.c:3127
> stm_register_device+0xf3/0x5c0: stm_register_device at drivers/hwtracing/stm/core.c:695
...
Which is basically a result of the stm class trying to allocate ~512kB
for the dummy_stm with its default parameters. There's no reason, however,
for it not to be vmalloc()ed instead, which is what this patch does.
Reported-by: Fengguang Wu <fengguang.wu@intel.com> Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> CC: stable@vger.kernel.org # v4.4+ Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Since an SRP remote port is attached as a child to shost->shost_gendev
and as the only child, the translation from the shost pointer into an
rport pointer must happen by looking up the shost child that is an
rport. This patch fixes the following KASAN complaint:
BUG: KASAN: slab-out-of-bounds in srp_timed_out+0x57/0x110 [scsi_transport_srp]
Read of size 4 at addr ffff880035d3fcc0 by task kworker/1:0H/19
Having PR_FP_MODE_FRE (i.e. Config5.FRE) set without PR_FP_MODE_FR (i.e.
Status.FR) is not supported as the lone purpose of Config5.FRE is to
emulate Status.FR=0 handling on FPU hardware that has Status.FR=1
hardwired[1][2]. Also we do not handle this case elsewhere, and assume
throughout our code that TIF_HYBRID_FPREGS and TIF_32BIT_FPREGS cannot
be set both at once for a task, leading to inconsistent behaviour if
this does happen.
Return unsuccessfully then from prctl(2) PR_SET_FP_MODE calls requesting
PR_FP_MODE_FRE to be set with PR_FP_MODE_FR clear. This corresponds to
modes allowed by `mips_set_personality_fp'.
References:
[1] "MIPS Architecture For Programmers, Vol. III: MIPS32 / microMIPS32
Privileged Resource Architecture", Imagination Technologies,
Document Number: MD00090, Revision 6.02, July 10, 2015, Table 9.69
"Config5 Register Field Descriptions", p. 262
[2] "MIPS Architecture For Programmers, Volume III: MIPS64 / microMIPS64
Privileged Resource Architecture", Imagination Technologies,
Document Number: MD00091, Revision 6.03, December 22, 2015, Table
9.72 "Config5 Register Field Descriptions", p. 288
Fixes: 9791554b45a2 ("MIPS,prctl: add PR_[GS]ET_FP_MODE prctl options for MIPS") Signed-off-by: Maciej W. Rozycki <macro@mips.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: linux-mips@linux-mips.org Cc: <stable@vger.kernel.org> # 4.0+
Patchwork: https://patchwork.linux-mips.org/patch/19327/ Signed-off-by: James Hogan <jhogan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Use 64-bit accesses for 64-bit floating-point general registers with
PTRACE_PEEKUSR, removing the truncation of their upper halves in the
FR=1 mode, caused by commit bbd426f542cb ("MIPS: Simplify FP context
access"), which inadvertently switched them to using 32-bit accesses.
The PTRACE_POKEUSR side is fine as it's never been broken and continues
using 64-bit accesses.
Fixes: bbd426f542cb ("MIPS: Simplify FP context access") Signed-off-by: Maciej W. Rozycki <macro@mips.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: linux-mips@linux-mips.org Cc: <stable@vger.kernel.org> # 3.15+
Patchwork: https://patchwork.linux-mips.org/patch/19334/ Signed-off-by: James Hogan <jhogan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
While doing a global software reset, these bits are not cleared and let
some bootloader fail to initialise the GPHYs. The bootloader don't
expect the GPHYs in reset, as they aren't during power on.
The asserts were a workaround for a wrong syscon-reboot mask. With a
mask set which includes the GPHY resets, these resets aren't required
any more.
Fixes: 126534141b45 ("MIPS: lantiq: Add a GPHY driver which uses the RCU syscon-mfd") Signed-off-by: Mathias Kresin <dev@kresin.me> Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Acked-by: Hauke Mehrtens <hauke@hauke-m.de> Cc: John Crispin <john@phrozen.org> Cc: linux-mips@linux-mips.org Cc: <stable@vger.kernel.org> # 4.14+
Patchwork: https://patchwork.linux-mips.org/patch/19003/
[jhogan@kernel.org: Fix build warnings] Signed-off-by: James Hogan <jhogan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
We need to select the buffer code, otherwise we get build errors
with undefined functions on the trigger and buffer,
if we select just IIO and then AT91_SAMA5D2_ADC from menuconfig
This adds a Kconfig 'select' statement like other ADC
drivers have it already.
Fixes: 5e1a1da0f8c9 ("iio: adc: at91-sama5d2_adc: add hw trigger and buffer support") Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Note that using 1073741824 instead of 1073741825 causes "write error:
Cannot allocate memory" but no OOPS.
This is because 1073741824 == 2^30 and 1073741825 == 2^30+1. Since kfifo
rounds up to the nearest power of 2, it will actually call kmalloc with
roundup_pow_of_two(length) * bytes_per_datum.
Using length == 1073741825 and bytes_per_datum == 2, we get:
so this overflows to 0, causing kmalloc to return ZERO_SIZE_PTR and
subsequent memcpy to fail once the device is enabled.
Fix this by checking for overflow prior to allocating a kfifo. With this
check added, the above code returns -EINVAL when enabling the buffer,
rather than causing an OOPS.
Signed-off-by: Martin Kelly <mkelly@xevo.com>
cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Currently, we use int for buffer length and bytes_per_datum. However,
kfifo uses unsigned int for length and size_t for element size. We need
to make sure these matches or we will have bugs related to overflow (in
the range between INT_MAX and UINT_MAX for length, for example).
In addition, set_bytes_per_datum uses size_t while bytes_per_datum is an
int, which would cause bugs for large values of bytes_per_datum.
Change buffer length to use unsigned int and bytes_per_datum to use
size_t.
Signed-off-by: Martin Kelly <mkelly@xevo.com> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
This commit is a follow-up to changes made to ad_sigma_delta.h
in staging: iio: ad7192: implement IIO_CHAN_INFO_SAMP_FREQ
which broke ad7793 as it was not altered to match those changes.
This driver predates the availability of IIO_CHAN_INFO_SAMP_FREQ
attribute wherein usage has some advantages like it can be accessed by
in-kernel consumers as well as reduces the code size.
Therefore, use IIO_CHAN_INFO_SAMP_FREQ to implement the
sampling_frequency attribute instead of using IIO_DEV_ATTR_SAMP_FREQ()
macro.
Move code from the functions associated with IIO_DEV_ATTR_SAMP_FREQ()
into respective read and write hooks with the mask set to
IIO_CHAN_INFO_SAMP_FREQ.
Fixes: a13e831fcaa7 ("staging: iio: ad7192: implement IIO_CHAN_INFO_SAMP_FREQ") Signed-off-by: Michael Nosthoff <committed@heine.so> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
When using large tcp_rmem[2] values (I did tests with 500 MB),
I noticed overflows while computing rcvwin.
Lets fix this before the following patch.
Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Acked-by: Wei Wang <weiwan@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[Backport: sysctl_tcp_rmem is not Namespace-ify'd in older kernels] Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Currently, GCC disables -Wunused-const-variable, but not
-Wunused-variable, so warns unused variables if they are
non-constant.
While, Clang does not warn unused variables at all regardless of
the const qualifier because -Wno-unused-const-variable is implied
by the stronger option -Wno-unused-variable.
Disable -Wunused-const-variable instead of -Wunused-variable so that
GCC and Clang work in the same way.
In _rtl92c_get_txpower_writeval_by_regulatory() the variable writeVal
is assigned to itself in an if ... else statement, apparently only to
document that the branch condition is handled and that a previously read
value should be returned unmodified. The self-assignment causes clang to
raise the following warning:
drivers/net/wireless/realtek/rtlwifi/rtl8192cu/rf.c:304:13:
error: explicitly assigning value of variable of type 'u32'
(aka 'unsigned int') to itself [-Werror,-Wself-assign]
writeVal = writeVal;
Delete the branch with the self-assignment.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Reviewed-by: Guenter Roeck <groeck@chromium.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
In several locations the driver uses AMD_CG_STATE_UNGATE (type enum
amd_clockgating_state) instead of AMD_PG_STATE_UNGATE (type enum
amd_powergating_stat) and vice versa. Both constants have the same
value, so this doesn't cause any problems, but we still want to pass
the correct type.
Fixing the mismatch resolves multiple warnings like this when building
with clang:
drivers/gpu/drm/amd/amdgpu/../powerplay/hwmgr/cz_clockpowergating.c:169:7:
error: implicit conversion from enumeration type 'enum
amd_powergating_state' to different enumeration type 'enum
amd_clockgating_state' [-Werror,-Wenum-conversion]
AMD_PG_STATE_UNGATE);
Reviewed-by: Guenter Roeck <groeck@chromium.org> Signed-off-by: Matthias Kaehlcke <mka@chromium.org> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
wiphy names were recently limited to 128 bytes by commit a7cfebcb7594
("cfg80211: limit wiphy names to 128 bytes"). As it turns out though,
this isn't sufficient because dev_vprintk_emit() needs the syslog header
string "SUBSYSTEM=ieee80211\0DEVICE=+ieee80211:$devname" to fit into 128
bytes. This triggered the "device/subsystem name too long" WARN when
the device name was >= 90 bytes. As before, this was reproduced by
syzbot by sending an HWSIM_CMD_NEW_RADIO command to the MAC80211_HWSIM
generic netlink family.
Fix it by further limiting wiphy names to 64 bytes.
Reported-by: syzbot+e64565577af34b3768dc@syzkaller.appspotmail.com Fixes: a7cfebcb7594 ("cfg80211: limit wiphy names to 128 bytes") Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
If user get root access and calls security.selinux setxattr() with an
embedded NUL on a file and then if some process performs a getxattr()
on that file with a length greater than the actual length of the string,
it would result in a panic.
To fix this, add the actual length of the string to the security context
instead of the length passed by the userspace process.
Signed-off-by: Sachin Grover <sgrover@codeaurora.org> Cc: stable@vger.kernel.org Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The snapshot trigger currently only affects the main ring buffer, even when
it is used by the instances. This can be confusing as the snapshot trigger
is listed in the instance.
> # cd /sys/kernel/tracing
> # mkdir instances/foo
> # echo snapshot > instances/foo/events/syscalls/sys_enter_fchownat/trigger
> # echo top buffer > trace_marker
> # echo foo buffer > instances/foo/trace_marker
> # touch /tmp/bar
> # chown rostedt /tmp/bar
> # cat instances/foo/snapshot
# tracer: nop
#
#
# * Snapshot is freed *
#
# Snapshot commands:
# echo 0 > snapshot : Clears and frees snapshot buffer
# echo 1 > snapshot : Allocates snapshot buffer, if not already allocated.
# Takes a snapshot of the main buffer.
# echo 2 > snapshot : Clears snapshot buffer (but does not allocate or free)
# (Doesn't have to be '2' works with any number that
# is not a '0' or '1')
New ICs (like the one on the Lenovo T480s) answer to
ETP_SMBUS_IAP_VERSION_CMD 4 bytes instead of 3. This corrupts the stack
as i2c_smbus_read_block_data() uses the values returned by the i2c
device to know how many data it need to return.
i2c_smbus_read_block_data() can read up to 32 bytes (I2C_SMBUS_BLOCK_MAX)
and there is no safeguard on how many bytes are provided in the return
value. Ensure we always have enough space for any future firmware.
Also 0-initialize the values to prevent any access to uninitialized memory.
This time, Lenovo decided to go with different pieces in its latest
series of Thinkpads.
For those we have been able to test:
- the T480 is using Synaptics with an IBM trackpoint
-> it behaves properly with or without intertouch, there is no point
not using RMI4
- the X1 Carbon 6th gen is using Synaptics with an IBM trackpoint
-> the touchpad doesn't behave properly under PS/2 so we have to
switch it to RMI4 if we do not want to have disappointed users
- the X280 is using Synaptics with an ALPS trackpoint
-> the recent fixes in the trackpoint handling fixed it so upstream
now works fine with or without RMI4, and there is no point not
using RMI4
- the T480s is using an Elan touchpad, so that's a different story
projects / mirror_ubuntu-bionic-kernel.git / log