Sending MIDI messages to a PODxt through the USB connection shows
"usb_submit_urb failed" in dmesg and the message is not received by
the POD.
The error is caused because in the funcion send_midi_async() in midi.c
there is a call to usb_sndbulkpipe() for endpoint 3 OUT, but the PODxt
USB descriptor shows that this endpoint it's an interrupt endpoint.
Patch tested with PODxt only.
[ The bug has been present from the very beginning in the staging
driver time, but Fixes below points to the commit moving to sound/
directory so that the fix can be cleanly applied -- tiwai ]
Two years ago I tried an AMD Radeon E8860 embedded GPU with the drm driver.
The dmesg output included driver warnings about an invalid PCIe lane width.
Tracking the problem back led to si_set_pcie_lane_width_in_smc().
The calculation of the lane widths via ATOM_PPLIB_PCIE_LINK_WIDTH_MASK and
ATOM_PPLIB_PCIE_LINK_WIDTH_SHIFT macros did not increment the resulting
value, per the comment in pptable.h ("lanes - 1"), and per usage elsewhere.
Applying the increment silenced the warnings.
The code has not changed since, so either my analysis was incorrect or the
bug has gone unnoticed. Hence submitting this as an RFC.
Acked-by: Christian König <christian.koenig@amd.com> Acked-by: Chunming Zhou <david1.zhou@amd.com> Signed-off-by: Paul Parsons <lost.distance@yahoo.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Khalid Elmously <khalid.elmously@canonical.com> Acked-by: Brad Figg <brad.figg@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Calling request_irq() followed by disable_irq() is usually a bad idea,
specially if the interrupt can be pending, and you're not yet in a
position to handle it.
This is exactly what happens on my kevin system when rebooting in a
second kernel using kexec: Some interrupt is left pending from
the previous kernel, and we take it too early, before disable_irq()
could do anything.
Let's clear the pending interrupts as we initialize the HW, and move
the interrupt request after that point. This ensures that we're in
a sane state when the interrupt is requested.
The calculation of the lane widths via ATOM_PPLIB_PCIE_LINK_WIDTH_MASK and
ATOM_PPLIB_PCIE_LINK_WIDTH_SHIFT macros did not increment the resulting
value, per the comment in pptable.h ("lanes - 1"), and per usage elsewhere.
Port of the radeon fix to amdgpu.
Acked-by: Christian König <christian.koenig@amd.com> Acked-by: Chunming Zhou <david1.zhou@amd.com>
Bug: https://bugs.freedesktop.org/show_bug.cgi?id=102553 Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Khalid Elmously <khalid.elmously@canonical.com> Acked-by: Brad Figg <brad.figg@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If these bos are evicted and are in the validated list
things blow up, so do not put them in there. Notably,
that tries to add the bo to the LRU twice, which results
in a BUG_ON in ttm_bo.c.
While for the bo_list an alternative would be to not allow
always valid bos in there, that does not work for the user
fence.
v2: Fixed whitespace issue pointed out by checkpatch.pl
Signed-off-by: Bas Nieuwenhuizen <basni@chromium.org> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Khalid Elmously <khalid.elmously@canonical.com> Acked-by: Brad Figg <brad.figg@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The commit 02a5d6925cd3 ("ALSA: pcm: Avoid potential races between OSS
ioctls and read/write") split the PCM preparation code to a locked
version, and it added a sanity check of runtime->oss.prepare flag
along with the change. This leaded to an endless loop when the stream
gets XRUN: namely, snd_pcm_oss_write3() and co call
snd_pcm_oss_prepare() without setting runtime->oss.prepare flag and
the loop continues until the PCM state reaches to another one.
As the function is supposed to execute the preparation
unconditionally, drop the invalid state check there.
The previous fix 40cab6e88cb0 ("ALSA: pcm: Return -EBUSY for OSS
ioctls changing busy streams") introduced some mutex unbalance; the
check of runtime->oss.rw_ref was inserted in a wrong place after the
mutex lock.
This patch fixes the inconsistency by rewriting with the helper
functions to lock/unlock parameters with the stream check.
OSS PCM stream management isn't modal but it allows ioctls issued at
any time for changing the parameters. In the previous hardening
patch ("ALSA: pcm: Avoid potential races between OSS ioctls and
read/write"), we covered these races and prevent the corruption by
protecting the concurrent accesses via params_lock mutex. However,
this means that some ioctls that try to change the stream parameter
(e.g. channels or format) would be blocked until the read/write
finishes, and it may take really long.
Basically changing the parameter while reading/writing is an invalid
operation, hence it's even more user-friendly from the API POV if it
returns -EBUSY in such a situation.
This patch adds such checks in the relevant ioctls with the addition
of read/write access refcount.
Although we apply the params_lock mutex to the whole read and write
operations as well as snd_pcm_oss_change_params(), we may still face
some races.
First off, the params_lock is taken inside the read and write loop.
This is intentional for avoiding the too long locking, but it allows
the in-between parameter change, which might lead to invalid
pointers. We check the readiness of the stream and set up via
snd_pcm_oss_make_ready() at the beginning of read and write, but it's
called only once, by assuming that it remains ready in the rest.
Second, many ioctls that may change the actual parameters
(i.e. setting runtime->oss.params=1) aren't protected, hence they can
be processed in a half-baked state.
This patch is an attempt to plug these holes. The stream readiness
check is moved inside the read/write inner loop, so that the stream is
always set up in a proper state before further processing. Also, each
ioctl that may change the parameter is wrapped with the params_lock
for avoiding the races.
The issues were triggered by syzkaller in a few different scenarios,
particularly the one below appearing as GPF in loopback_pos_update.
When device boots with T > T_trip_1 and requests interrupt,
the race condition takes place. The interrupt comes before
THERMAL_DEVICE_ENABLED is set. This leads to an attempt to
reading sensor value from irq and disabling the sensor, based on
the data->mode field, which expected to be THERMAL_DEVICE_ENABLED,
but still stays as THERMAL_DEVICE_DISABLED. Afher this issue
sensor is never re-enabled, as the driver state is wrong.
Fix this problem by setting the 'data' members prior to
requesting the interrupts.
In order to enable a PLL, not only the PLL has to be powered up and
locked, but you also have to de-assert the reset signal. The last part
was missing. Add it so PLLs that were not enabled by the FW/bootloader
can be enabled from Linux.
Fixes: 41691b8862e2 ("clk: bcm2835: Add support for programming the audio domain clocks") Cc: <stable@vger.kernel.org> Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Reviewed-by: Eric Anholt <eric@anholt.net> Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Khalid Elmously <khalid.elmously@canonical.com> Acked-by: Brad Figg <brad.figg@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The clock for which all PWM devices on MT7623 or MT2701 actually depending
on has to be divided by four from its parent clock axi_sel in the clock
path prior to PWM devices.
Consequently, adding a fixed-factor clock axisel_d4 as one-fourth of
clock axi_sel allows that PWM devices can have the correct resolution
calculation.
Cc: stable@vger.kernel.org Fixes: e9862118272a ("clk: mediatek: Add MT2701 clock support") Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Khalid Elmously <khalid.elmously@canonical.com> Acked-by: Brad Figg <brad.figg@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When we build this driver with on x86-32, gcc produces a false-positive warning:
drivers/clk/renesas/clk-sh73a0.c: In function 'sh73a0_cpg_clocks_init':
drivers/clk/renesas/clk-sh73a0.c:155:10: error: 'parent_name' may be used uninitialized in this function [-Werror=maybe-uninitialized]
return clk_register_fixed_factor(NULL, name, parent_name, 0,
We can work around that warning by adding a fake initialization, I tried
and failed to come up with any better workaround. This is currently one
of few remaining warnings for a 4.14.y randconfig build, so it would be
good to also have it backported at least to that version. Older versions
have more randconfig warnings, so we might not care.
I had not noticed this earlier, because one patch in my randconfig test
tree removes the '-ffreestanding' option on x86-32, and that avoids
the warning. The -ffreestanding flag was originally global but moved
into arch/i386 by Andi Kleen in commit 6edfba1b33c7 ("[PATCH] x86_64:
Don't define string functions to builtin") as a 'temporary workaround'.
Like many temporary hacks, this turned out to be rather long-lived, from
all I can tell we still need a simple fix to asm/string_32.h before it
can be removed, but I'm not sure about how to best do that.
Clearfog boards can come with a CPU clocked at 1600MHz (commercial)
or 1333MHz (industrial).
They have also some dip-switches to select a different clock (666, 800,
1066, 1200).
The funny thing is that the recovery button is on the MPP34 fq selector.
So, when booting an industrial board with this button down, the frequency
666MHz is selected (and the kernel didn't boot).
This patch add all the missing clocks.
The only mode I didn't test is 2GHz (uboot found 4294MHz instead :/ ).
Fixes: 0e85aeced4d6 ("clk: mvebu: add clock support for Armada 380/385") Cc: <stable@vger.kernel.org> # 3.16.x: 9593f4f56cf5: clk: mvebu: armada-38x: add support for 1866MHz variants Cc: <stable@vger.kernel.org> # 3.16.x Signed-off-by: Richard Genoud <richard.genoud@gmail.com> Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Khalid Elmously <khalid.elmously@canonical.com> Acked-by: Brad Figg <brad.figg@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Per PCIe r3.1, sec 2.2.6.2 and 7.8.4, a Requester may not use 8-bit Tags
unless its Extended Tag Field Enable is set, but all Receivers/Completers
must handle 8-bit Tags correctly regardless of their Extended Tag Field
Enable.
Some devices do not handle 8-bit Tags as Completers, so add a quirk for
them. If we find such a device, we disable Extended Tags for the entire
hierarchy to make peer-to-peer DMA possible.
The Broadcom HT1100/HT2000/HT2100 seems to have issues with handling 8-bit
tags. Mark it as broken.
This fixes Xorg hangs and unresponsive keyboards with errors like this:
radeon 0000:06:00.0: GPU lockup (current fence id 0x000000000000000e last fence id 0x0000000000000
[drm:r600_ring_test [radeon]] *ERROR* radeon: ring 0 test failed (scratch(0x8504)=0xCAFEDEAD)
[drm:r600_resume [radeon]] *ERROR* r600 startup failed on resume
Fixes: 60db3a4d8cc9 ("PCI: Enable PCIe Extended Tags if supported") Link: https://bugzilla.kernel.org/show_bug.cgi?id=196197 Signed-off-by: Sinan Kaya <okaya@codeaurora.org> Signed-off-by: Bjorn Helgaas <helgaas@kernel.org> CC: stable@vger.kernel.org # v4.11: 62ce94a7a5a5 PCI: Mark Broadcom HT2100 Root Port Extended Tags as broken CC: stable@vger.kernel.org # v4.11 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Khalid Elmously <khalid.elmously@canonical.com> Acked-by: Brad Figg <brad.figg@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
A spinlock is held while updating the internal copy of the IRQ mask,
but not while writing it to the actual IMASK register. After the lock
is released, an IRQ can occur before the IMASK register is written.
If handling this IRQ causes the mask to be changed, when the handler
returns back to the middle of the first mask update, a stale value
will be written to the mask register.
If this causes an IRQ to become unmasked that cannot have its status
cleared by writing a 1 to it in the IREG register, e.g. the SDIO IRQ,
then we can end up stuck with the same IRQ repeatedly being fired but
not handled. Normally the MMC IRQ handler attempts to clear any
unexpected IRQs by writing IREG, but for those that cannot be cleared
in this way then the IRQ will just repeatedly fire.
This was resulting in lockups after a while of using Wi-Fi on the
CI20 (GitHub issue #19).
Resolve by holding the spinlock until after the IMASK register has
been updated.
Cc: stable@vger.kernel.org Link: https://github.com/MIPS/CI20_linux/issues/19 Fixes: 61bfbdb85687 ("MMC: Add support for the controller on JZ4740 SoCs.") Tested-by: Mathieu Malaterre <malat@debian.org> Signed-off-by: Alex Smith <alex.smith@imgtec.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Khalid Elmously <khalid.elmously@canonical.com> Acked-by: Brad Figg <brad.figg@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
glibc 2.26 removed the 'struct ucontext' to "improve" POSIX compliance
and break programs, including User Mode Linux. Fix User Mode Linux
by using POSIX ucontext_t.
This fixes:
arch/um/os-Linux/signal.c: In function 'hard_handler':
arch/um/os-Linux/signal.c:163:22: error: dereferencing pointer to incomplete type 'struct ucontext'
mcontext_t *mc = &uc->uc_mcontext;
arch/x86/um/stub_segv.c: In function 'stub_segv_handler':
arch/x86/um/stub_segv.c:16:13: error: dereferencing pointer to incomplete type 'struct ucontext'
&uc->uc_mcontext);
Cc: stable@vger.kernel.org Signed-off-by: Krzysztof Mazur <krzysiek@podlesie.net> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Khalid Elmously <khalid.elmously@canonical.com> Acked-by: Brad Figg <brad.figg@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Recent libcs have gotten a bit more strict, so we actually need to
include the right headers and use the right types. This enables UML to
compile again.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Cc: stable@vger.kernel.org Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Khalid Elmously <khalid.elmously@canonical.com> Acked-by: Brad Figg <brad.figg@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The ring buffer is made up of a link list of pages. When making the ring
buffer bigger, it will allocate all the pages it needs before adding to the
ring buffer, and if it fails, it frees them and returns an error. This makes
increasing the ring buffer size an all or nothing action. When this was
first created, the pages were allocated with "NORETRY". This was to not
cause any Out-Of-Memory (OOM) actions from allocating the ring buffer. But
NORETRY was too strict, as the ring buffer would fail to expand even when
there's memory available, but was taken up in the page cache.
Commit 848618857d253 ("tracing/ring_buffer: Try harder to allocate") changed
the allocating from NORETRY to RETRY_MAYFAIL. The RETRY_MAYFAIL would
allocate from the page cache, but if there was no memory available, it would
simple fail the allocation and not trigger an OOM.
This worked fine, but had one problem. As the ring buffer would allocate one
page at a time, it could take up all memory in the system before it failed
to allocate and free that memory. If the allocation is happening and the
ring buffer allocates all memory and then tries to take more than available,
its allocation will not trigger an OOM, but if there's any allocation that
happens someplace else, that could trigger an OOM, even though once the ring
buffer's allocation fails, it would free up all the previous memory it tried
to allocate, and allow other memory allocations to succeed.
Commit d02bd27bd33dd ("mm/page_alloc.c: calculate 'available' memory in a
separate function") separated out si_mem_availble() as a separate function
that could be used to see how much memory is available in the system. Using
this function to make sure that the ring buffer could be allocated before it
tries to allocate pages we can avoid allocating all memory in the system and
making it vulnerable to OOMs if other allocations are taking place.
Link: http://lkml.kernel.org/r/1522320104-6573-1-git-send-email-zhaoyang.huang@spreadtrum.com CC: stable@vger.kernel.org Cc: linux-mm@kvack.org Fixes: 848618857d253 ("tracing/ring_buffer: Try harder to allocate")
Requires: d02bd27bd33dd ("mm/page_alloc.c: calculate 'available' memory in a separate function") Reported-by: Zhaoyang Huang <huangzhaoyang@gmail.com> Tested-by: Joel Fernandes <joelaf@google.com> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Khalid Elmously <khalid.elmously@canonical.com> Acked-by: Brad Figg <brad.figg@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Per the ACPI specification the only functional purpose for a DIMM
Control Region to be mapped into the system physical address space, from
an OSPM perspective, is to support block-apertures. However, there are
some BIOSen that publish DIMM Control Region SPA entries for pre-boot
environment consumption. Undo the kernel policy of generating disabled
'ndblk' regions when this configuration is detected.
Cc: <stable@vger.kernel.org> Fixes: 1f7df6f88b92 ("libnvdimm, nfit: regions (block-data-window...)") Reviewed-by: Toshi Kani <toshi.kani@hpe.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Khalid Elmously <khalid.elmously@canonical.com> Acked-by: Brad Figg <brad.figg@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
There is a small window whereby ARS scan requests can schedule work that
userspace will miss when polling scrub_show. Hold the init_mutex lock
over calls to report the status to close this potential escape. Also,
make sure that requests to cancel the ARS workqueue are treated as an
idle event.
Cc: <stable@vger.kernel.org> Cc: Vishal Verma <vishal.l.verma@intel.com> Fixes: 37b137ff8c83 ("nfit, libnvdimm: allow an ARS scrub...") Reviewed-by: Dave Jiang <dave.jiang@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Khalid Elmously <khalid.elmously@canonical.com> Acked-by: Brad Figg <brad.figg@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
/*
* Give up if we don't find an instance of a uuid at each
* position (from 0 to nd_region->ndr_mappings - 1), or if we
* find a dimm with two instances of the same uuid.
*/
dev_err(&nd_region->dev, "%s missing label for %pUb\n",
dev_name(ndd->dev), nd_label->uuid);
At initialization time the 'dimm' driver caches a copy of the memory
device's label area and reserves address space for each of the
namespaces defined.
However, as can be seen below, the reservation occurs even when the
index blocks are invalid:
The Acer Acer Veriton X4110G has a TPM device detected as:
tpm_tis 00:0b: 1.2 TPM (device-id 0xFE, rev-id 71)
After the first S3 suspend, the following error appears during resume:
tpm tpm0: A TPM error(38) occurred continue selftest
Any following S3 suspend attempts will now fail with this error:
tpm tpm0: Error (38) sending savestate before suspend
PM: Device 00:0b failed to suspend: error 38
Error 38 is TPM_ERR_INVALID_POSTINIT which means the TPM is
not in the correct state. This indicates that the platform BIOS
is not sending the usual TPM_Startup command during S3 resume.
>From this point onwards, all TPM commands will fail.
The same issue was previously reported on Foxconn 6150BK8MC and
Sony Vaio TX3.
The platform behaviour seems broken here, but we should not break
suspend/resume because of this.
When the unexpected TPM state is encountered, set a flag to skip the
affected TPM_SaveState command on later suspends.
Cc: stable@vger.kernel.org Signed-off-by: Chris Chiu <chiu@endlessm.com> Signed-off-by: Daniel Drake <drake@endlessm.com> Link: http://lkml.kernel.org/r/CAB4CAwfSCvj1cudi+MWaB5g2Z67d9DwY1o475YOZD64ma23UiQ@mail.gmail.com Link: https://lkml.org/lkml/2011/3/28/192 Link: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=591031 Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Khalid Elmously <khalid.elmously@canonical.com> Acked-by: Brad Figg <brad.figg@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
cxllib_handle_fault() is called by an external driver when it needs to
have the host resolve page faults for a buffer. The buffer can cover
several pages and VMAs. The function iterates over all the pages used
by the buffer, based on the page size of the VMA.
To ensure some stability while processing the faults, the thread T1
grabs the mm->mmap_sem semaphore with read access (R1). However, when
processing a page fault for a single page, one of the underlying
functions, copro_handle_mm_fault(), also grabs the same semaphore with
read access (R2). So the thread T1 takes the semaphore twice.
If another thread T2 tries to access the semaphore in write mode W1
(say, because it wants to allocate memory and calls 'brk'), then that
thread T2 will have to wait because there's a reader (R1). If the
thread T1 is processing a new page at that time, it won't get an
automatic grant at R2, because there's now a writer thread
waiting (T2). And we have a deadlock.
The timeline is:
1. thread T1 owns the semaphore with read access R1
2. thread T2 requests write access W1 and waits
3. thread T1 requests read access R2 and waits
The fix is for the thread T1 to release the semaphore R1 once it got
the information it needs from the current VMA. The address space/VMAs
could evolve while T1 iterates over the full buffer, but in the
unlikely case where T1 misses a page, the external driver will raise a
new page fault when retrying the memory access.
Fixes: 3ced8d730063 ("cxl: Export library to support IBM XSL") Cc: stable@vger.kernel.org # 4.13+ Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Khalid Elmously <khalid.elmously@canonical.com> Acked-by: Brad Figg <brad.figg@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Despite the efforts made to correctly read the NDA and CUBC registers,
the order in which the registers are read could sometimes lead to an
inconsistent state.
Re-using the timeline from the comments, this following timing of
registers reads could lead to reading NDA with value "@desc2" and
CUBC with value "MAX desc1":
This is allowed by the condition ((check_nda == cur_nda) && initd),
despite cur_ubc and cur_nda being in the precise state we don't want.
This error leads to incorrect residue computation.
Fix it by inversing the order in which CUBC and INITD are read. This
makes sure that NDA and CUBC are always read together either _before_
INITD goes to 0 or _after_ it is back at 1.
The case where NDA is read before INITD is at 0 and CUBC is read after
INITD is back at 1 will be rejected by check_nda and cur_nda being
different.
Ensure that cv_end is equal to ibdev->num_comp_vectors for the
NUMA node with the highest index. This patch improves spreading
of RDMA channels over completion vectors and thereby improves
performance, especially on systems with only a single NUMA node.
This patch drops support for the comp_vector login parameter by
ignoring the value of that parameter since I have not found a
good way to combine support for that parameter and automatic
spreading of RDMA channels over completion vectors.
Fixes: d92c0da71a35 ("IB/srp: Add multichannel support") Reported-by: Alexander Schmid <alex@modula-shop-systems.de> Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com> Cc: Alexander Schmid <alex@modula-shop-systems.de> Cc: stable@vger.kernel.org Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Khalid Elmously <khalid.elmously@canonical.com> Acked-by: Brad Figg <brad.figg@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Before commit e494f6a72839 ("[SCSI] improved eh timeout handler") it
did not really matter whether or not abort handlers like srp_abort()
called .scsi_done() when returning another value than SUCCESS. Since
that commit however this matters. Hence only call .scsi_done() when
returning SUCCESS.
The PCM runtime object is created and freed dynamically at PCM stream
open / close time. This is tracked via substream->runtime, and it's
cleared at snd_pcm_detach_substream().
The runtime object assignment is protected by PCM open_mutex, so for
all PCM operations, it's safely handled. However, each PCM substream
provides also an ALSA timer interface, and user-space can access to
this while closing a PCM substream. This may eventually lead to a
UAF, as snd_pcm_timer_resolution() tries to access the runtime while
clearing it in other side.
Fortunately, it's the only concurrent access from the PCM timer, and
it merely reads runtime->timer_resolution field. So, we can avoid the
race by reordering kfree() and wrapping the substream->runtime
clearance with the corresponding timer lock.
This patch avoids that KASAN reports the following when the SRP initiator
calls srp_post_send():
==================================================================
BUG: KASAN: stack-out-of-bounds in rxe_post_send+0x5c4/0x980 [rdma_rxe]
Read of size 8 at addr ffff880066606e30 by task 02-mq/1074
Check to make sure that ctx->cm_id->device is set before we use it.
Otherwise userspace can trigger a NULL dereference by doing
RDMA_USER_CM_CMD_SET_OPTION on an ID that is not bound to a device.
dm-crypt consumes an excessive amount memory when the user attempts to
zero a dm-crypt device with "blkdiscard -z". The command "blkdiscard -z"
calls the BLKZEROOUT ioctl, it goes to the function __blkdev_issue_zeroout,
__blkdev_issue_zeroout sends a large amount of write bios that contain
the zero page as their payload.
For each incoming page, dm-crypt allocates another page that holds the
encrypted data, so when processing "blkdiscard -z", dm-crypt tries to
allocate the amount of memory that is equal to the size of the device.
This can trigger OOM killer or cause system crash.
Fix this by limiting the amount of memory that dm-crypt allocates to 2%
of total system memory. This limit is system-wide and is divided by the
number of active dm-crypt devices and each device receives an equal
share.
Add explicit checks in ext4_xattr_block_get() just in case the
e_value_offs and e_value_size fields in the the xattr block are
corrupted in memory after the buffer_verified bit is set on the xattr
block.
Add some paranoia checks to make sure we don't stray beyond the end of
the valid memory region containing ext4 xattr entries while we are
scanning for a match.
Also rename the function to xattr_find_entry() since it is static and
thus only used in fs/ext4/xattr.c
Refactor the call to EXT4_ERROR_INODE() into ext4_xattr_check_block().
This simplifies the code, and fixes a problem where not all callers of
ext4_xattr_check_block() were not resulting in ext4_error() getting
called when the xattr block is corrupted.
If some metadata block, such as an allocation bitmap, overlaps the
superblock, it's very likely that if the file system is mounted
read/write, the results will not be pretty. So disallow r/w mounts
for file systems corrupted in this particular way.
The extended attribute code now uses the crc32c checksum for hashing
purposes, so we should just always always initialize it. We also want
to prevent NULL pointer dereferences if one of the metadata checksum
features is enabled after the file sytsem is originally mounted.
ext4 isn't validating the sizes of xattrs where the value of the xattr
is stored in an external inode. This is problematic because
->e_value_size is a u32, but ext4_xattr_get() returns an int. A very
large size is misinterpreted as an error code, which ext4_get_acl()
translates into a bogus ERR_PTR() for which IS_ERR() returns false,
causing a crash.
Fix this by validating that all xattrs are <= INT_MAX bytes.
i_disksize update should be protected by i_data_sem, by either taking
the lock explicitly or by using ext4_update_i_disksize() helper. But the
i_disksize updates in ext4_direct_IO_write() are not protected at all,
which may be racing with i_disksize updates in writeback path in
delalloc buffer write path.
This is found by code inspection, and I didn't hit any i_disksize
corruption due to this bug. Thanks to Jan Kara for catching this bug and
suggesting the fix!
Reported-by: Jan Kara <jack@suse.cz> Suggested-by: Jan Kara <jack@suse.cz> Signed-off-by: Eryu Guan <guaneryu@gmail.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Khalid Elmously <khalid.elmously@canonical.com> Acked-by: Brad Figg <brad.figg@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When reading the inode or block allocation bitmap, if the bitmap needs
to be initialized, do not update the checksum in the block group
descriptor. That's because we're not set up to journal those changes.
Instead, just set the verified bit on the bitmap block, so that it's
not necessary to validate the checksum.
When a block or inode allocation actually happens, at that point the
checksum will be calculated, and update of the bg descriptor block
will be properly journalled.
Previously the jbd2 layer assumed that a file system check would be
required after a journal abort. In the case of the deliberate file
system shutdown, this should not be necessary. Allow the jbd2 layer
to distinguish between these two cases by using the ESHUTDOWN errno.
Also add proper locking to __journal_abort_soft().
The ext4 forced shutdown flag needs to prevent new handles from being
started, but it needs to allow existing handles to complete. So the
forced shutdown flag should not force ext4_journal_get_write_access to
fail.
Early alpha processors cannot write a single byte or word; they read 8
bytes, modify the value in registers and write back 8 bytes.
The type blk_status_t is defined as one byte, it is often written
asynchronously by I/O completion routines, this asynchronous modification
can corrupt content of nearby bytes if these nearby bytes can be written
simultaneously by another CPU.
- one example of such corruption is the structure dm_io where
"blk_status_t status" is written by an asynchronous completion routine
and "atomic_t io_count" is modified synchronously
- another example is the structure dm_buffer where "unsigned hold_count"
is modified synchronously from process context and "blk_status_t
write_error" is modified asynchronously from bio completion routine
This patch fixes the bug by changing the type blk_status_t to 32 bits if
we are on Alpha and if we are compiling for a processor that doesn't have
the byte-word-extension.
This fixes a harmless UBSAN where root could potentially end up
causing an overflow while bumping the entropy_total field (which is
ignored once the entropy pool has been initialized, and this generally
is completed during the boot sequence).
This is marginal for the stable kernel series, but it's a really
trivial patch, and it fixes UBSAN warning that might cause security
folks to get overly excited for no reason.
Most MMIO GIC register accesses use a 1-hot bit scheme that
avoids requiring any form of locking. This isn't true for the
GICD_ICFGRn registers, which require a RMW sequence.
Unfortunately, we seem to be missing a lock for these particular
accesses, which could result in a race condition if changing the
trigger type on any two interrupts within the same set of 16
interrupts (and thus controlled by the same CFGR register).
Introduce a private lock in the GIC common comde for this
particular case, making it cover both GIC implementations
in one go.
Fix the topology kcontrol string handling so that string pointer
references are strdup()ed instead of being copied. This fixes issues
with kcontrol templates on the stack or ones that are freed. Remember
and free the strings too when topology is unloaded.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Khalid Elmously <khalid.elmously@canonical.com> Acked-by: Brad Figg <brad.figg@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
SSM2602 driver is broken on recent kernels (at least
since 4.9). User space applications such as amixer or
alsamixer get EIO when attempting to access codec
controls via the relevant IOCTLs.
Root cause of these failures is the regcache_hw_init
function in drivers/base/regmap/regcache.c, which
prevents regmap cache initalization from the
reg_defaults_raw element of the regmap_config structure
when registers are write only. It also disables the
regmap cache entirely when all registers are write only
or volatile as is the case for the SSM2602 driver.
Using the reg_defaults element of the regmap_config
structure rather than the reg_defaults_raw element to
initalize the regmap cache avoids the logic in the
regcache_hw_init function entirely. It also makes this
driver consistent with other ASoC codec drivers, as
this driver was the ONLY codec driver that used the
reg_defaults_raw element to initalize the cache.
Tested on Digilent Zybo Z7 development board which has
a SSM2603 codec chip connected to a Xilinx Zynq SoC.
Signed-off-by: James Kelly <jamespeterkelly@gmail.com> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Khalid Elmously <khalid.elmously@canonical.com> Acked-by: Brad Figg <brad.figg@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Fix the pointer to struct scp_subdomian not being moved forward
when each sub-domain is expected to be iteratively added through
pm_genpd_add_subdomain call.
Cc: stable@vger.kernel.org Fixes: 53fddb1a66dd ("soc: mediatek: reduce code duplication of scpsys_probe across all SoCs") Reported-by: Weiyi Lu <weiyi.lu@mediatek.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Khalid Elmously <khalid.elmously@canonical.com> Acked-by: Brad Figg <brad.figg@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Follow the change of return type u32 of hid_report_len,
fix all the types of variables those get the return value of
hid_report_len to u32, and all other code already uses u32.
The OPAL NVRAM driver does not sleep in case it gets OPAL_BUSY or
OPAL_BUSY_EVENT from firmware, which causes large scheduling
latencies, and various lockup errors to trigger (again, BMC reboot
can cause it).
Fix this by converting it to the standard form OPAL_BUSY loop that
sleeps.
Fixes: 628daa8d5abf ("powerpc/powernv: Add RTC and NVRAM support plus RTAS fallbacks")
Depends-on: 34dd25de9fe3 ("powerpc/powernv: define a standard delay for OPAL_BUSY type retry loops") Cc: stable@vger.kernel.org # v3.2+ Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Khalid Elmously <khalid.elmously@canonical.com> Acked-by: Brad Figg <brad.figg@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This is the start of an effort to tidy up and standardise all the
delays. Existing loops have a range of delay/sleep periods from 1ms
to 20ms, and some have no delay. They all loop forever except rtc,
which times out after 10 retries, and that uses 10ms delays. So use
10ms as our standard delay. The OPAL maintainer agrees 10ms is a
reasonable starting point.
The idea is to use the same recipe everywhere, once this is proven to
work then it will be documented as an OPAL API standard. Then both
firmware and OS can agree, and if a particular call needs something
else, then that can be documented with reasoning.
This is not the end-all of this effort, it's just a relatively easy
change that fixes some existing high latency delays. There should be
provision for standardising timeouts and/or interruptible loops where
possible, so non-fatal firmware errors don't cause hangs.
kexec_file_load() on powerpc doesn't support kdump kernels yet, so it
returns -ENOTSUPP in that case.
I've recently learned that this errno is internal to the kernel and
isn't supposed to be exposed to userspace. Therefore, change to
-EOPNOTSUPP which is defined in an uapi header.
This does indeed make kexec-tools happier. Before the patch, on
ppc64le:
This is showing up since OPTPROBES is now enabled with CONFIG_PREEMPT.
trampoline_probe_handler() considers itself to be a special kprobe
handler for kretprobes. In doing so, it expects to be called from
kprobe_handler() on a trap, and re-enables preemption before returning a
non-zero return value so as to suppress any subsequent processing of the
trap by the kprobe_handler().
However, with optprobes, we don't deal with special handlers (we ignore
the return code) and just try to re-enable preemption causing the above
trace.
To address this, modify trampoline_probe_handler() to not be special.
The only additional processing done in kprobe_handler() is to emulate
the instruction (in this case, a 'nop'). We adjust the value of
regs->nip for the purpose and delegate the job of re-enabling
preemption and resetting current kprobe to the probe handlers
(kprobe_handler() or optimized_callback()).
Fixes: 8a2d71a3f273 ("powerpc/kprobes: Disable preemption before invoking probe handler for optprobes") Cc: stable@vger.kernel.org # v4.15+ Reported-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> Acked-by: Ananth N Mavinakayanahalli <ananth@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Khalid Elmously <khalid.elmously@canonical.com> Acked-by: Brad Figg <brad.figg@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
asm/barrier.h is not always included after asm/synch.h, which meant
it was missing __SUBARCH_HAS_LWSYNC, so in some files smp_wmb() would
be eieio when it should be lwsync. kernel/time/hrtimer.c is one case.
__SUBARCH_HAS_LWSYNC is only used in one place, so just fold it in
to where it's used. Previously with my small simulator config, 377
instances of eieio in the tree. After this patch there are 55.
On POWER9, since commit cc3d2940133d ("powerpc/64: Enable use of radix
MMU under hypervisor on POWER9", 2017-01-30), we set both the radix and
HPT bits in the client-architecture-support (CAS) vector, which tells
the hypervisor that we can do either radix or HPT. According to PAPR,
if we use this combination we are promising to do a H_REGISTER_PROC_TBL
hcall later on to let the hypervisor know whether we are doing radix
or HPT. We currently do this call if we are doing radix but not if
we are doing HPT. If the hypervisor is able to support both radix
and HPT guests, it would be entitled to defer allocation of the HPT
until the H_REGISTER_PROC_TBL call, and to fail any attempts to create
HPTEs until the H_REGISTER_PROC_TBL call. Thus we need to do a
H_REGISTER_PROC_TBL call when we are doing HPT; otherwise we may
crash at boot time.
This adds the code to call H_REGISTER_PROC_TBL in this case, before
we attempt to create any HPT entries using H_ENTER.
Fixes: cc3d2940133d ("powerpc/64: Enable use of radix MMU under hypervisor on POWER9") Cc: stable@vger.kernel.org # v4.11+ Signed-off-by: Paul Mackerras <paulus@ozlabs.org> Reviewed-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Khalid Elmously <khalid.elmously@canonical.com> Acked-by: Brad Figg <brad.figg@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Presently the dt_cpu_ftrs restore_cpu will only add bits to the LPCR
for secondaries, but some bits must be removed (e.g., UPRT for HPT).
Not clearing these bits on secondaries causes checkstops when booting
with disable_radix.
restore_cpu can not just set LPCR, because it is also called by the
idle wakeup code which relies on opal_slw_set_reg to restore the value
of LPCR, at least on P8 which does not save LPCR to stack in the idle
code.
Fix this by including a mask of bits to clear from LPCR as well, which
is used by restore_cpu.
This is a little messy now, but it's a minimal fix that can be
backported. Longer term, the idle SPR save/restore code can be
reworked to completely avoid calls to restore_cpu, then restore_cpu
would be able to unconditionally set LPCR to match boot processor
environment.
Fixes: 5a61ef74f269f ("powerpc/64s: Support new device tree binding for discovering CPU features") Cc: stable@vger.kernel.org # v4.12+ Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Khalid Elmously <khalid.elmously@canonical.com> Acked-by: Brad Figg <brad.figg@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
shash and sdesc and always allocated and freed together.
* abstract this in new functions cifs_alloc_hash() and cifs_free_hash().
* make smb2/3 crypto allocation independent from each other.
Signed-off-by: Aurelien Aptel <aaptel@suse.com> Signed-off-by: Steve French <smfrench@gmail.com> Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com> CC: Stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Khalid Elmously <khalid.elmously@canonical.com> Acked-by: Brad Figg <brad.figg@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
On some systems, the BIOS expects certain SMBus register values to
match the hardware defaults. Restore these configuration registers at
shutdown time to avoid confusing the BIOS. This avoids hard-locking
such systems upon reboot.
Signed-off-by: Jean Delvare <jdelvare@suse.de> Tested-by: Jason Andryuk <jandryuk@gmail.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Khalid Elmously <khalid.elmously@canonical.com> Acked-by: Brad Figg <brad.figg@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Saving the original value of register SMBSLVCMD in
i801_enable_host_notify() doesn't work, because this function is
called not only at probe time but also at resume time. Do it in
i801_probe() instead, so that the saved value is not overwritten at
resume time.
Signed-off-by: Jean Delvare <jdelvare@suse.de> Fixes: 22e94bd6779e ("i2c: i801: store and restore the SLVCMD register at load and unload") Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Tested-by: Jason Andryuk <jandryuk@gmail.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Cc: stable@vger.kernel.org # v4.10+ Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Khalid Elmously <khalid.elmously@canonical.com> Acked-by: Brad Figg <brad.figg@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
We can not use the standard sg_set_buf() fucntion since when
CONFIG_DEBUG_SG=y this adds a check that will BUG_ON for cifs.ko
when we pass it an object from the stack.
Create a new wrapper smb2_sg_set_buf() which avoids doing that particular check
and use it for smb3 encryption instead.
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by: Steve French <smfrench@gmail.com> CC: Stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Khalid Elmously <khalid.elmously@canonical.com> Acked-by: Brad Figg <brad.figg@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This is a requirement which has always existed but, somehow, wasn't
reflected in the documentation and problems weren't found until now
when Tuba Yavuz found a possible deadlock happening between dwc3 and
f_hid. She described the situation as follows:
spin_lock_irqsave(&hidg->write_spinlock, flags); // first acquire
/* we our function has been disabled by host */
if (!hidg->req) {
free_ep_req(hidg->in_ep, hidg->req);
goto try_again;
}
[...]
status = usb_ep_queue(hidg->in_ep, hidg->req, GFP_ATOMIC);
=>
[...]
=> usb_gadget_giveback_request
=>
f_hidg_req_complete
=>
spin_lock_irqsave(&hidg->write_spinlock, flags); // second acquire
Note that this happens because dwc3 would call ->complete() on a
failed usb_ep_queue() due to failed Start Transfer command. This is,
anyway, a theoretical situation because dwc3 currently uses "No
Response Update Transfer" command for Bulk and Interrupt endpoints.
It's still good to make this case impossible to happen even if the "No
Reponse Update Transfer" command is changed.
USB3 specification 10.10, Enhanced SuperSpeed hubs only support selective
suspend and resume, they do not support global suspend/resume where the
hub downstream facing ports states are not affected.
When system enters hibernation it first enters freeze process where only
the root hub enters suspend, usb_port_suspend() is not called for other
devices, and suspend status flags are not set for them. Other devices are
expected to suspend globally. Some external USB3 hubs will suspend the
downstream facing port at global suspend. These devices won't be resumed
at thaw as the suspend status flag is not set.
A USB3 removable hard disk connected through a USB3 hub that won't resume
at thaw will fail to synchronize SCSI cache, return “cmd cmplt err -71”
error, and needs a 60 seconds timeout which causing system hang for 60s
before the USB host reset the port for the USB3 removable hard disk to
recover.
Fix this by always calling usb_port_suspend() during freeze for USB3
devices.
It looks like there is a possibility of a double-free vulnerability on an
error path of the f_midi_set_alt function in the f_midi driver. If the
path is feasible then free_ep_req gets called twice:
req->complete = f_midi_complete;
err = usb_ep_queue(midi->out_ep, req, GFP_ATOMIC);
=> ...
usb_gadget_giveback_request
=>
f_midi_complete (CALLBACK)
(inside f_midi_complete, for various cases of status)
free_ep_req(ep, req); // first kfree
if (err) {
ERROR(midi, "%s: couldn't enqueue request: %d\n",
midi->out_ep->name, err);
free_ep_req(midi->out_ep, req); // second kfree
return err;
}
The double-free possibility was introduced with commit ad0d1a058eac
("usb: gadget: f_midi: fix leak on failed to enqueue out requests").
Found by MOXCAFE tool.
Signed-off-by: Tuba Yavuz <tuba@ece.ufl.edu> Fixes: ad0d1a058eac ("usb: gadget: f_midi: fix leak on failed to enqueue out requests") Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Khalid Elmously <khalid.elmously@canonical.com> Acked-by: Brad Figg <brad.figg@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Mike Lothian reported that plugging in a USB-C device does not work
properly in his Dell Alienware system. This system has an Intel Alpine
Ridge Thunderbolt controller providing USB-C functionality. In these
systems the USB controller (xHCI) is hotplugged whenever a device is
connected to the port using ACPI-based hotplug.
The ACPI description of the root port in question is as follows:
Device (RP01)
{
Name (_ADR, 0x001C0000)
Device (PXSX)
{
Name (_ADR, 0x02)
Method (_RMV, 0, NotSerialized)
{
// ...
}
}
Here _ADR 0x02 means device 0, function 2 on the bus under root port (RP01)
but that seems to be incorrect because device 0 is the upstream port of the
Alpine Ridge PCIe switch and it has no functions other than 0 (the bridge
itself). When we get ACPI Notify() to the root port resulting from
connecting a USB-C device, Linux tries to read PCI_VENDOR_ID from device 0,
function 2 which of course always returns 0xffffffff because there is no
such function and we never find the device.
In Windows this works fine.
Now, since we get ACPI Notify() to the root port and not to the PXSX device
we should actually start our scan from there as well and not from the
non-existent PXSX device. Fix this by checking presence of the slot itself
(function 0) if we fail to do that otherwise.
While there use pci_bus_read_dev_vendor_id() in get_slot_status(), which is
the recommended way to read Device and Vendor IDs of devices on PCI buses.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=198557 Reported-by: Mike Lothian <mike@fireburn.co.uk> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Khalid Elmously <khalid.elmously@canonical.com> Acked-by: Brad Figg <brad.figg@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Just like many other Samsung models, the 670Z5E needs to use the acpi-video
backlight interface rather then the native one for backlight control to
work, add a quirk for this.
Buglink: https://bugzilla.redhat.com/show_bug.cgi?id=1557060 Cc: All applicable <stable@vger.kernel.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Khalid Elmously <khalid.elmously@canonical.com> Acked-by: Brad Figg <brad.figg@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
We're supposed to be checking that "val_len" is not too large but
instead we check if it is smaller than the max.
The only function affected would be regmap_i2c_smbus_i2c_write() in
drivers/base/regmap/regmap-i2c.c. Strangely that function has its own
limit check which returns an error if (count >= I2C_SMBUS_BLOCK_MAX) so
it doesn't look like it has ever been able to do anything except return
an error.
Fixes: c335931ed9d2 ("regmap: Add raw_write/read checks for max_raw_write/read sizes") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Khalid Elmously <khalid.elmously@canonical.com> Acked-by: Brad Figg <brad.figg@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Commit 2cc42bac1c79 ("x86-64/Xen: eliminate W+X mappings") introduced a
call to get_cpu_cap, which is fstack-protected. This is works on x86-64
as commit 4f277295e54c ("x86/xen: init %gs very early to avoid page
faults with stack protector") ensures the stack protector is configured,
but it it did not cover x86-32.
Delay calling get_cpu_cap until after xen_setup_gdt has initialized the
stack canary. Without this, a 32bit PV machine crashes early
in boot.
(XEN) Domain 0 (vcpu#0) crashed on cpu#0:
(XEN) ----[ Xen-4.6.6-xc x86_64 debug=n Tainted: C ]----
(XEN) CPU: 0
(XEN) RIP: e019:[<00000000c10362f8>]
And the PV kernel IP corresponds to init_scattered_cpuid_features
0xc10362f8 <+24>: mov %gs:0x14,%eax
When a BRx is provided by a pipeline, the WPF must determine the master
layer. Currently the condition to check this identifies pipe->bru ||
pipe->num_inputs > 1.
The code then moves on to dereference pipe->bru, thus the check fails
static analysers on the possibility that pipe->num_inputs could be
greater than 1 without pipe->bru being set.
The reality is that the pipeline must have a BRx to support more than
one input, thus this could never cause a fault - however it also
identifies that the num_inputs > 1 check is redundant.
Remove the redundant check - and always configure the master layer
appropriately when we have a BRx configured in our pipeline.
Commit 9b61e302210e (spi: Pick spi bus number from Linux idr or spi alias)
ceased to unregister SPI buses with fixed bus numbers. Moreover this is
visible only if CONFIG_SPI_DEBUG=y is set or when trying to re-register
the same SPI controller.
modprobe spi_pxa2xx_platform:
[ 37.883137] sysfs: cannot create duplicate filename '/devices/pci0000:00/0000:00:19.0/pxa2xx-spi.12/spi_master/spi1'
[ 37.894984] CPU: 1 PID: 1467 Comm: modprobe Not tainted 4.16.0-rc4+ #21
[ 37.902384] Call Trace:
...
[ 38.122680] kobject_add_internal failed for spi1 with -EEXIST, don't try to register things with the same name in the same directory.
[ 38.136154] WARNING: CPU: 1 PID: 1467 at lib/kobject.c:238 kobject_add_internal+0x2a5/0x2f0
...
[ 38.513817] pxa2xx-spi pxa2xx-spi.12: problem registering spi master
[ 38.521036] pxa2xx-spi: probe of pxa2xx-spi.12 failed with error -17
Fix this by not returning immediately from spi_unregister_controller() if
idr_find() doesn't find controller with given ID/bus number. It finds
only those controllers that were registered with dynamic SPI bus
numbers. Only conditional cleanup between dynamic and fixed bus numbers
is to remove allocated IDR.
Fixes: 9b61e302210e (spi: Pick spi bus number from Linux idr or spi alias) Cc: stable@vger.kernel.org Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Khalid Elmously <khalid.elmously@canonical.com> Acked-by: Brad Figg <brad.figg@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When SPI transfers can be offloaded using DMA, the SPI core need to
build a scatterlist to make sure that the buffer to be transferred is
dma-able.
This patch fixes the scatterlist entry size computation in the case
where the maximum acceptable scatterlist entry supported by the DMA
controller is less than PAGE_SIZE, when the buffer is vmalloced.
For each entry, the actual size is given by the minimum between the
desc_len (which is the max buffer size supported by the DMA controller)
and the remaining buffer length until we cross a page boundary.
Fixes: 65598c13fd66 ("spi: Fix per-page mapping of unaligned vmalloc-ed buffer") Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Khalid Elmously <khalid.elmously@canonical.com> Acked-by: Brad Figg <brad.figg@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The datasheet recommends initializing FIFOs before
SPI enable. If we do not do it like this, there may be
a strange behavior. We noticed that DMA does not work properly
with FIFOs if we do not clear them beforehand or enable them
before SPIEN.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Khalid Elmously <khalid.elmously@canonical.com> Acked-by: Brad Figg <brad.figg@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The compatible string is incorrect. Add atmel,sama5d3-pinctrl since
it's the appropriate compatible string. Remove the
atmel,at91rm9200-pinctrl compatible string, this fallback is
useless, there are too many changes.
The proper name for the property, which assign given device to IOMMU is
'iommus', not 'iommu'. Fix incorrect name and let all GScaler devices
to be properly handled when IOMMU support is enabled.
Reported-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Fixes: 6cbfdd73a94f ("ARM: dts: add sysmmu nodes for exynos5250") Cc: <stable@vger.kernel.org> # v4.8+ Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Khalid Elmously <khalid.elmously@canonical.com> Acked-by: Brad Figg <brad.figg@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
There are only 19 PIOB pins having primary names PB0-PB18. Not all of them
have a 'C' function. So the pinctrl property mask ends up being the same as the
other SoC of the at91sam9x5 series.
Fix that USB initialization fails as below runtime log is present during
booting on bananapi-r2 board by adding missing regulators the USB device
requires. Current regulators USB device uses are being updated with the
correct ones to reflect real configurations which are all from fixed
regulators rather than MT6323 one's output.
xhci-mtk 1a1c0000.usb: 1a1c0000.usb supply vbus not found, using dummy regulator
xhci-mtk 1a240000.usb: 1a240000.usb supply vbus not found, using dummy regulator
Cc: stable@vger.kernel.org Fixes: f4ff257cd160 ("arm: dts: mt7623: add support for Bananapi R2 (BPI-R2) board") Signed-off-by: Sean Wang <sean.wang@mediatek.com>
[mb: update kernel log in commit message] Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Khalid Elmously <khalid.elmously@canonical.com> Acked-by: Brad Figg <brad.figg@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Since commit 04c8b0f82c7d ("irqchip/gic: Make locking a BL_SWITCHER only
feature") coupled CPU idle freezes from time to time on Exynos4210. Later
commit 313c8c16ee62 ("PM / CPU: replace raw_notifier with atomic_notifier")
changed the context in which the CPU idle code is executed, what results
in fully reproducible freeze all the time. However, almost the same coupled
CPU idle code works fine on Exynos3250 regardless of the changes made in
the mentioned commits.
It turned out that the IPI call used on Exynos4210 is conflicting with the
change done in the first mentioned commit in GIC. Fix this by using the
same code path as for Exynos3250, instead of the IPI call for
synchronization with second CPU core, call dsb_sev() directly.
Tested on Exynos4210-based Trats and Origen boards.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> CC: <stable@vger.kernel.org> # v4.13+ Acked-by: Marc Zyngier <marc.zyngier@arm.com> Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Khalid Elmously <khalid.elmously@canonical.com> Acked-by: Brad Figg <brad.figg@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>