Documentation/kmsg/s390/xpram

   1 /*?
   2  * Text: "%d is not a valid number of XPRAM devices\n"
   3  * Severity: Error
   4  * Parameter:
   5  *   @1: number of partitions
   6  * Description:
   7  * The number of XPRAM partitions specified for the 'devs' module parameter
   8  * or with the 'xpram.parts' kernel parameter must be an integer in the
   9  * range 1 to 32. The XPRAM device driver created a maximum of 32 partitions
  10  * that are probably not configured as intended.
  11  * User action:
  12  * If the XPRAM device driver has been compiled as a separate module,
  13  * unload the module and load it again with a correct value for the 'devs'
  14  * module parameter. If the XPRAM device driver has been compiled
  15  * into the kernel, correct the 'xpram.parts' parameter in the kernel
  16  * command line and restart Linux.
  17  */
  18
  19 /*?
  20  * Text: "Not enough expanded memory available\n"
  21  * Severity: Error
  22  * Description:
  23  * The amount of expanded memory required to set up your XPRAM partitions
  24  * depends on the 'sizes' parameter specified for the xpram module or on
  25  * the specifications for the 'xpram.parts' parameter if the XPRAM device
  26  * driver has been compiled into the kernel. Your
  27  * current specification exceed the amount of available expanded memory.
  28  * Your XPRAM partitions are probably not configured as intended.
  29  * User action:
  30  * If the XPRAM device driver has been compiled as a separate module,
  31  * unload the xpram module and load it again with an appropriate value
  32  * for the 'sizes' module parameter. If the XPRAM device driver has been
  33  * compiled into the kernel, adjust the 'xpram.parts' parameter in the
  34  * kernel command line and restart Linux. If you need more than the
  35  * available expanded memory, increase the expanded memory allocation for
  36  * your virtual hardware or LPAR.
  37  */
  38
  39 /*?
  40  * Text: "No expanded memory available\n"
  41  * Severity: Error
  42  * Description:
  43  * The XPRAM device driver has been loaded in a Linux instance that runs
  44  * in an LPAR or virtual hardware without expanded memory.
  45  * No XPRAM partitions are created.
  46  * User action:
  47  * Allocate expanded memory for your LPAR or virtual hardware or do not
  48  * load the xpram module. You can ignore this message, if you do not want
  49  * to create XPRAM partitions.
  50  */
  51
  52 /*?
  53  * Text: "Resuming the system failed: %s\n"
  54  * Severity: Error
  55  * Parameter:
  56  *   @1: cause of the failure
  57  * Description:
  58  * A system cannot be resumed if the expanded memory setup changes
  59  * after hibernation. Possible reasons for the failure are:
  60  * - Expanded memory was removed after hibernation.
  61  * - Size of the expanded memory changed after hibernation.
  62  * The system is stopped with a kernel panic.
  63  * User action:
  64  * Reboot Linux.
  65  */
  66
  67 /*? Text: "  number of devices (partitions): %d \n" */
  68 /*? Text: "  size of partition %d: %u kB\n" */
  69 /*? Text: "  size of partition %d to be set automatically\n" */
  70 /*? Text: "  memory needed (for sized partitions): %lu kB\n" */
  71 /*? Text: "  partitions to be sized automatically: %d\n" */
  72 /*? Text: "  automatically determined partition size: %lu kB\n" */
  73 /*? Text: "  %u pages expanded memory found (%lu KB).\n" */
  74 /*? Text: "%s: %d output lines suppressed due to ratelimiting\n" */