drivers/spi/Kconfig

   1 #
   2 # SPI driver configuration
   3 #
   4 # NOTE:  the reason this doesn't show SPI slave support is mostly that
   5 # nobody's needed a slave side API yet.  The master-role API is not
   6 # fully appropriate there, so it'd need some thought to do well.
   7 #
   8 menuconfig SPI
   9         bool "SPI support"
  10         depends on HAS_IOMEM
  11         help
  12           The "Serial Peripheral Interface" is a low level synchronous
  13           protocol.  Chips that support SPI can have data transfer rates
  14           up to several tens of Mbit/sec.  Chips are addressed with a
  15           controller and a chipselect.  Most SPI slaves don't support
  16           dynamic device discovery; some are even write-only or read-only.
  17
  18           SPI is widely used by microcontrollers to talk with sensors,
  19           eeprom and flash memory, codecs and various other controller
  20           chips, analog to digital (and d-to-a) converters, and more.
  21           MMC and SD cards can be accessed using SPI protocol; and for
  22           DataFlash cards used in MMC sockets, SPI must always be used.
  23
  24           SPI is one of a family of similar protocols using a four wire
  25           interface (select, clock, data in, data out) including Microwire
  26           (half duplex), SSP, SSI, and PSP.  This driver framework should
  27           work with most such devices and controllers.
  28
  29 if SPI
  30
  31 config SPI_DEBUG
  32         bool "Debug support for SPI drivers"
  33         depends on DEBUG_KERNEL
  34         help
  35           Say "yes" to enable debug messaging (like dev_dbg and pr_debug),
  36           sysfs, and debugfs support in SPI controller and protocol drivers.
  37
  38 #
  39 # MASTER side ... talking to discrete SPI slave chips including microcontrollers
  40 #
  41
  42 config SPI_MASTER
  43 #       bool "SPI Master Support"
  44         bool
  45         default SPI
  46         help
  47           If your system has an master-capable SPI controller (which
  48           provides the clock and chipselect), you can enable that
  49           controller and the protocol drivers for the SPI slave chips
  50           that are connected.
  51
  52 if SPI_MASTER
  53
  54 comment "SPI Master Controller Drivers"
  55
  56 config SPI_ALTERA
  57         tristate "Altera SPI Controller"
  58         select SPI_BITBANG
  59         help
  60           This is the driver for the Altera SPI Controller.
  61
  62 config SPI_ATH79
  63         tristate "Atheros AR71XX/AR724X/AR913X SPI controller driver"
  64         depends on ATH79 && GPIOLIB
  65         select SPI_BITBANG
  66         help
  67           This enables support for the SPI controller present on the
  68           Atheros AR71XX/AR724X/AR913X SoCs.
  69
  70 config SPI_ARMADA_3700
  71         tristate "Marvell Armada 3700 SPI Controller"
  72         depends on (ARCH_MVEBU && OF) || COMPILE_TEST
  73         help
  74           This enables support for the SPI controller present on the
  75           Marvell Armada 3700 SoCs.
  76
  77 config SPI_ATMEL
  78         tristate "Atmel SPI Controller"
  79         depends on HAS_DMA
  80         depends on (ARCH_AT91 || AVR32 || COMPILE_TEST)
  81         help
  82           This selects a driver for the Atmel SPI Controller, present on
  83           many AT32 (AVR32) and AT91 (ARM) chips.
  84
  85 config SPI_AU1550
  86         tristate "Au1550/Au1200/Au1300 SPI Controller"
  87         depends on MIPS_ALCHEMY
  88         select SPI_BITBANG
  89         help
  90           If you say yes to this option, support will be included for the
  91           PSC SPI controller found on Au1550, Au1200 and Au1300 series.
  92
  93 config SPI_AXI_SPI_ENGINE
  94         tristate "Analog Devices AXI SPI Engine controller"
  95         depends on HAS_IOMEM
  96         help
  97           This enables support for the Analog Devices AXI SPI Engine SPI controller.
  98           It is part of the SPI Engine framework that is used in some Analog Devices
  99           reference designs for FPGAs.
 100
 101 config SPI_BCM2835
 102         tristate "BCM2835 SPI controller"
 103         depends on GPIOLIB
 104         depends on ARCH_BCM2835 || COMPILE_TEST
 105         help
 106           This selects a driver for the Broadcom BCM2835 SPI master.
 107
 108           The BCM2835 contains two types of SPI master controller; the
 109           "universal SPI master", and the regular SPI controller. This driver
 110           is for the regular SPI controller. Slave mode operation is not also
 111           not supported.
 112
 113 config SPI_BCM2835AUX
 114         tristate "BCM2835 SPI auxiliary controller"
 115         depends on (ARCH_BCM2835 && GPIOLIB) || COMPILE_TEST
 116         help
 117           This selects a driver for the Broadcom BCM2835 SPI aux master.
 118
 119           The BCM2835 contains two types of SPI master controller; the
 120           "universal SPI master", and the regular SPI controller.
 121           This driver is for the universal/auxiliary SPI controller.
 122
 123 config SPI_BFIN5XX
 124         tristate "SPI controller driver for ADI Blackfin5xx"
 125         depends on BLACKFIN && !BF60x
 126         help
 127           This is the SPI controller master driver for Blackfin 5xx processor.
 128
 129 config SPI_ADI_V3
 130         tristate "SPI controller v3 for ADI"
 131         depends on BF60x
 132         help
 133           This is the SPI controller v3 master driver
 134           found on Blackfin 60x processor.
 135
 136 config SPI_BFIN_SPORT
 137         tristate "SPI bus via Blackfin SPORT"
 138         depends on BLACKFIN
 139         help
 140           Enable support for a SPI bus via the Blackfin SPORT peripheral.
 141
 142 config SPI_BCM53XX
 143         tristate "Broadcom BCM53xx SPI controller"
 144         depends on ARCH_BCM_5301X
 145         depends on BCMA_POSSIBLE
 146         select BCMA
 147         help
 148           Enable support for the SPI controller on Broadcom BCM53xx ARM SoCs.
 149
 150 config SPI_BCM63XX
 151         tristate "Broadcom BCM63xx SPI controller"
 152         depends on BCM63XX || COMPILE_TEST
 153         help
 154           Enable support for the SPI controller on the Broadcom BCM63xx SoCs.
 155
 156 config SPI_BCM63XX_HSSPI
 157         tristate "Broadcom BCM63XX HS SPI controller driver"
 158         depends on BCM63XX || COMPILE_TEST
 159         help
 160           This enables support for the High Speed SPI controller present on
 161           newer Broadcom BCM63XX SoCs.
 162
 163 config SPI_BCM_QSPI
 164         tristate "Broadcom BSPI and MSPI controller support"
 165         depends on ARCH_BRCMSTB || ARCH_BCM || ARCH_BCM_IPROC || \
 166                         BMIPS_GENERIC || COMPILE_TEST
 167         default ARCH_BCM_IPROC
 168         help
 169           Enables support for the Broadcom SPI flash and MSPI controller.
 170           Select this option for any one of BRCMSTB, iProc NSP and NS2 SoCs
 171           based platforms. This driver works for both SPI master for spi-nor
 172           flash device as well as MSPI device.
 173
 174 config SPI_BITBANG
 175         tristate "Utilities for Bitbanging SPI masters"
 176         help
 177           With a few GPIO pins, your system can bitbang the SPI protocol.
 178           Select this to get SPI support through I/O pins (GPIO, parallel
 179           port, etc).  Or, some systems' SPI master controller drivers use
 180           this code to manage the per-word or per-transfer accesses to the
 181           hardware shift registers.
 182
 183           This is library code, and is automatically selected by drivers that
 184           need it.  You only need to select this explicitly to support driver
 185           modules that aren't part of this kernel tree.
 186
 187 config SPI_BUTTERFLY
 188         tristate "Parallel port adapter for AVR Butterfly (DEVELOPMENT)"
 189         depends on PARPORT
 190         select SPI_BITBANG
 191         help
 192           This uses a custom parallel port cable to connect to an AVR
 193           Butterfly <http://www.atmel.com/products/avr/butterfly>, an
 194           inexpensive battery powered microcontroller evaluation board.
 195           This same cable can be used to flash new firmware.
 196
 197 config SPI_CADENCE
 198         tristate "Cadence SPI controller"
 199         help
 200           This selects the Cadence SPI controller master driver
 201           used by Xilinx Zynq and ZynqMP.
 202
 203 config SPI_CLPS711X
 204         tristate "CLPS711X host SPI controller"
 205         depends on ARCH_CLPS711X || COMPILE_TEST
 206         help
 207           This enables dedicated general purpose SPI/Microwire1-compatible
 208           master mode interface (SSI1) for CLPS711X-based CPUs.
 209
 210 config SPI_COLDFIRE_QSPI
 211         tristate "Freescale Coldfire QSPI controller"
 212         depends on (M520x || M523x || M5249 || M525x || M527x || M528x || M532x)
 213         help
 214           This enables support for the Coldfire QSPI controller in master
 215           mode.
 216
 217 config SPI_DAVINCI
 218         tristate "Texas Instruments DaVinci/DA8x/OMAP-L/AM1x SoC SPI controller"
 219         depends on ARCH_DAVINCI || ARCH_KEYSTONE
 220         select SPI_BITBANG
 221         help
 222           SPI master controller for DaVinci/DA8x/OMAP-L/AM1x SPI modules.
 223
 224 config SPI_DESIGNWARE
 225         tristate "DesignWare SPI controller core support"
 226         help
 227           general driver for SPI controller core from DesignWare
 228
 229 config SPI_DW_PCI
 230         tristate "PCI interface driver for DW SPI core"
 231         depends on SPI_DESIGNWARE && PCI
 232
 233 config SPI_DW_MID_DMA
 234         bool "DMA support for DW SPI controller on Intel MID platform"
 235         depends on SPI_DW_PCI && DW_DMAC_PCI
 236
 237 config SPI_DW_MMIO
 238         tristate "Memory-mapped io interface driver for DW SPI core"
 239         depends on SPI_DESIGNWARE
 240
 241 config SPI_DLN2
 242        tristate "Diolan DLN-2 USB SPI adapter"
 243        depends on MFD_DLN2
 244        help
 245          If you say yes to this option, support will be included for Diolan
 246          DLN2, a USB to SPI interface.
 247
 248          This driver can also be built as a module.  If so, the module
 249          will be called spi-dln2.
 250
 251 config SPI_EFM32
 252         tristate "EFM32 SPI controller"
 253         depends on OF && ARM && (ARCH_EFM32 || COMPILE_TEST)
 254         select SPI_BITBANG
 255         help
 256           Driver for the spi controller found on Energy Micro's EFM32 SoCs.
 257
 258 config SPI_EP93XX
 259         tristate "Cirrus Logic EP93xx SPI controller"
 260         depends on HAS_DMA
 261         depends on ARCH_EP93XX || COMPILE_TEST
 262         help
 263           This enables using the Cirrus EP93xx SPI controller in master
 264           mode.
 265
 266 config SPI_FALCON
 267         bool "Falcon SPI controller support"
 268         depends on SOC_FALCON
 269         help
 270           The external bus unit (EBU) found on the FALC-ON SoC has SPI
 271           emulation that is designed for serial flash access. This driver
 272           has only been tested with m25p80 type chips. The hardware has no
 273           support for other types of SPI peripherals.
 274
 275 config SPI_FSL_LPSPI
 276         tristate "Freescale i.MX LPSPI controller"
 277         depends on ARCH_MXC || COMPILE_TEST
 278         help
 279           This enables Freescale i.MX LPSPI controllers in master mode.
 280
 281 config SPI_GPIO
 282         tristate "GPIO-based bitbanging SPI Master"
 283         depends on GPIOLIB || COMPILE_TEST
 284         select SPI_BITBANG
 285         help
 286           This simple GPIO bitbanging SPI master uses the arch-neutral GPIO
 287           interface to manage MOSI, MISO, SCK, and chipselect signals.  SPI
 288           slaves connected to a bus using this driver are configured as usual,
 289           except that the spi_board_info.controller_data holds the GPIO number
 290           for the chipselect used by this controller driver.
 291
 292           Note that this driver often won't achieve even 1 Mbit/sec speeds,
 293           making it unusually slow for SPI.  If your platform can inline
 294           GPIO operations, you should be able to leverage that for better
 295           speed with a custom version of this driver; see the source code.
 296
 297 config SPI_IMG_SPFI
 298         tristate "IMG SPFI controller"
 299         depends on MIPS || COMPILE_TEST
 300         help
 301           This enables support for the SPFI master controller found on
 302           IMG SoCs.
 303
 304 config SPI_IMX
 305         tristate "Freescale i.MX SPI controllers"
 306         depends on ARCH_MXC || COMPILE_TEST
 307         select SPI_BITBANG
 308         help
 309           This enables using the Freescale i.MX SPI controllers in master
 310           mode.
 311
 312 config SPI_JCORE
 313         tristate "J-Core SPI Master"
 314         depends on OF && (SUPERH || COMPILE_TEST)
 315         help
 316           This enables support for the SPI master controller in the J-Core
 317           synthesizable, open source SoC.
 318
 319 config SPI_LM70_LLP
 320         tristate "Parallel port adapter for LM70 eval board (DEVELOPMENT)"
 321         depends on PARPORT
 322         select SPI_BITBANG
 323         help
 324           This driver supports the NS LM70 LLP Evaluation Board,
 325           which interfaces to an LM70 temperature sensor using
 326           a parallel port.
 327
 328 config SPI_LP8841_RTC
 329         tristate "ICP DAS LP-8841 SPI Controller for RTC"
 330         depends on MACH_PXA27X_DT || COMPILE_TEST
 331         help
 332           This driver provides an SPI master device to drive Maxim
 333           DS-1302 real time clock.
 334
 335           Say N here unless you plan to run the kernel on an ICP DAS
 336           LP-8x4x industrial computer.
 337
 338 config SPI_MPC52xx
 339         tristate "Freescale MPC52xx SPI (non-PSC) controller support"
 340         depends on PPC_MPC52xx
 341         help
 342           This drivers supports the MPC52xx SPI controller in master SPI
 343           mode.
 344
 345 config SPI_MPC52xx_PSC
 346         tristate "Freescale MPC52xx PSC SPI controller"
 347         depends on PPC_MPC52xx
 348         help
 349           This enables using the Freescale MPC52xx Programmable Serial
 350           Controller in master SPI mode.
 351
 352 config SPI_MPC512x_PSC
 353         tristate "Freescale MPC512x PSC SPI controller"
 354         depends on PPC_MPC512x
 355         help
 356           This enables using the Freescale MPC5121 Programmable Serial
 357           Controller in SPI master mode.
 358
 359 config SPI_FSL_LIB
 360         tristate
 361         depends on OF
 362
 363 config SPI_FSL_CPM
 364         tristate
 365         depends on FSL_SOC
 366
 367 config SPI_FSL_SPI
 368         tristate "Freescale SPI controller and Aeroflex Gaisler GRLIB SPI controller"
 369         depends on OF
 370         select SPI_FSL_LIB
 371         select SPI_FSL_CPM if FSL_SOC
 372         help
 373           This enables using the Freescale SPI controllers in master mode.
 374           MPC83xx platform uses the controller in cpu mode or CPM/QE mode.
 375           MPC8569 uses the controller in QE mode, MPC8610 in cpu mode.
 376           This also enables using the Aeroflex Gaisler GRLIB SPI controller in
 377           master mode.
 378
 379 config SPI_FSL_DSPI
 380         tristate "Freescale DSPI controller"
 381         select REGMAP_MMIO
 382         depends on HAS_DMA
 383         depends on SOC_VF610 || SOC_LS1021A || ARCH_LAYERSCAPE || COMPILE_TEST
 384         help
 385           This enables support for the Freescale DSPI controller in master
 386           mode. VF610 platform uses the controller.
 387
 388 config SPI_FSL_ESPI
 389         tristate "Freescale eSPI controller"
 390         depends on FSL_SOC
 391         help
 392           This enables using the Freescale eSPI controllers in master mode.
 393           From MPC8536, 85xx platform uses the controller, and all P10xx,
 394           P20xx, P30xx,P40xx, P50xx uses this controller.
 395
 396 config SPI_MESON_SPIFC
 397         tristate "Amlogic Meson SPIFC controller"
 398         depends on ARCH_MESON || COMPILE_TEST
 399         select REGMAP_MMIO
 400         help
 401           This enables master mode support for the SPIFC (SPI flash
 402           controller) available in Amlogic Meson SoCs.
 403
 404 config SPI_MT65XX
 405         tristate "MediaTek SPI controller"
 406         depends on ARCH_MEDIATEK || COMPILE_TEST
 407         help
 408           This selects the MediaTek(R) SPI bus driver.
 409           If you want to use MediaTek(R) SPI interface,
 410           say Y or M here.If you are not sure, say N.
 411           SPI drivers for Mediatek MT65XX and MT81XX series ARM SoCs.
 412
 413 config SPI_NUC900
 414         tristate "Nuvoton NUC900 series SPI"
 415         depends on ARCH_W90X900
 416         select SPI_BITBANG
 417         help
 418           SPI driver for Nuvoton NUC900 series ARM SoCs
 419
 420 config SPI_LANTIQ_SSC
 421         tristate "Lantiq SSC SPI controller"
 422         depends on LANTIQ || COMPILE_TEST
 423         help
 424           This driver supports the Lantiq SSC SPI controller in master
 425           mode. This controller is found on Intel (former Lantiq) SoCs like
 426           the Danube, Falcon, xRX200, xRX300.
 427
 428 config SPI_OC_TINY
 429         tristate "OpenCores tiny SPI"
 430         depends on GPIOLIB || COMPILE_TEST
 431         select SPI_BITBANG
 432         help
 433           This is the driver for OpenCores tiny SPI master controller.
 434
 435 config SPI_OCTEON
 436         tristate "Cavium OCTEON SPI controller"
 437         depends on CAVIUM_OCTEON_SOC
 438         help
 439           SPI host driver for the hardware found on some Cavium OCTEON
 440           SOCs.
 441
 442 config SPI_OMAP_UWIRE
 443         tristate "OMAP1 MicroWire"
 444         depends on ARCH_OMAP1
 445         select SPI_BITBANG
 446         help
 447           This hooks up to the MicroWire controller on OMAP1 chips.
 448
 449 config SPI_OMAP24XX
 450         tristate "McSPI driver for OMAP"
 451         depends on HAS_DMA
 452         depends on ARCH_OMAP2PLUS || COMPILE_TEST
 453         select SG_SPLIT
 454         help
 455           SPI master controller for OMAP24XX and later Multichannel SPI
 456           (McSPI) modules.
 457
 458 config SPI_TI_QSPI
 459         tristate "DRA7xxx QSPI controller support"
 460         depends on ARCH_OMAP2PLUS || COMPILE_TEST
 461         help
 462           QSPI master controller for DRA7xxx used for flash devices.
 463           This device supports single, dual and quad read support, while
 464           it only supports single write mode.
 465
 466 config SPI_OMAP_100K
 467         tristate "OMAP SPI 100K"
 468         depends on ARCH_OMAP850 || ARCH_OMAP730 || COMPILE_TEST
 469         help
 470           OMAP SPI 100K master controller for omap7xx boards.
 471
 472 config SPI_ORION
 473         tristate "Orion SPI master"
 474         depends on PLAT_ORION || ARCH_MVEBU || COMPILE_TEST
 475         help
 476           This enables using the SPI master controller on the Orion
 477           and MVEBU chips.
 478
 479 config SPI_PIC32
 480         tristate "Microchip PIC32 series SPI"
 481         depends on MACH_PIC32 || COMPILE_TEST
 482         help
 483           SPI driver for Microchip PIC32 SPI master controller.
 484
 485 config SPI_PIC32_SQI
 486         tristate "Microchip PIC32 Quad SPI driver"
 487         depends on MACH_PIC32 || COMPILE_TEST
 488         depends on HAS_DMA
 489         help
 490           SPI driver for PIC32 Quad SPI controller.
 491
 492 config SPI_PL022
 493         tristate "ARM AMBA PL022 SSP controller"
 494         depends on ARM_AMBA
 495         default y if MACH_U300
 496         default y if ARCH_REALVIEW
 497         default y if INTEGRATOR_IMPD1
 498         default y if ARCH_VERSATILE
 499         help
 500           This selects the ARM(R) AMBA(R) PrimeCell PL022 SSP
 501           controller. If you have an embedded system with an AMBA(R)
 502           bus and a PL022 controller, say Y or M here.
 503
 504 config SPI_PPC4xx
 505         tristate "PPC4xx SPI Controller"
 506         depends on PPC32 && 4xx
 507         select SPI_BITBANG
 508         help
 509           This selects a driver for the PPC4xx SPI Controller.
 510
 511 config SPI_PXA2XX
 512         tristate "PXA2xx SSP SPI master"
 513         depends on (ARCH_PXA || PCI || ACPI)
 514         select PXA_SSP if ARCH_PXA
 515         help
 516           This enables using a PXA2xx or Sodaville SSP port as a SPI master
 517           controller. The driver can be configured to use any SSP port and
 518           additional documentation can be found a Documentation/spi/pxa2xx.
 519
 520 config SPI_PXA2XX_PCI
 521         def_tristate SPI_PXA2XX && PCI && COMMON_CLK
 522
 523 config SPI_ROCKCHIP
 524         tristate "Rockchip SPI controller driver"
 525         help
 526           This selects a driver for Rockchip SPI controller.
 527
 528           If you say yes to this option, support will be included for
 529           RK3066, RK3188 and RK3288 families of SPI controller.
 530           Rockchip SPI controller support DMA transport and PIO mode.
 531           The main usecase of this controller is to use spi flash as boot
 532           device.
 533
 534 config SPI_RB4XX
 535         tristate "Mikrotik RB4XX SPI master"
 536         depends on SPI_MASTER && ATH79
 537         help
 538           SPI controller driver for the Mikrotik RB4xx series boards.
 539
 540 config SPI_RSPI
 541         tristate "Renesas RSPI/QSPI controller"
 542         depends on SUPERH || ARCH_RENESAS || COMPILE_TEST
 543         help
 544           SPI driver for Renesas RSPI and QSPI blocks.
 545
 546 config SPI_QUP
 547         tristate "Qualcomm SPI controller with QUP interface"
 548         depends on ARCH_QCOM || (ARM && COMPILE_TEST)
 549         help
 550           Qualcomm Universal Peripheral (QUP) core is an AHB slave that
 551           provides a common data path (an output FIFO and an input FIFO)
 552           for serial peripheral interface (SPI) mini-core. SPI in master
 553           mode supports up to 50MHz, up to four chip selects, programmable
 554           data path from 4 bits to 32 bits and numerous protocol variants.
 555
 556           This driver can also be built as a module.  If so, the module
 557           will be called spi_qup.
 558
 559 config SPI_S3C24XX
 560         tristate "Samsung S3C24XX series SPI"
 561         depends on ARCH_S3C24XX
 562         select SPI_BITBANG
 563         help
 564           SPI driver for Samsung S3C24XX series ARM SoCs
 565
 566 config SPI_S3C24XX_FIQ
 567         bool "S3C24XX driver with FIQ pseudo-DMA"
 568         depends on SPI_S3C24XX
 569         select FIQ
 570         help
 571           Enable FIQ support for the S3C24XX SPI driver to provide pseudo
 572           DMA by using the fast-interrupt request framework, This allows
 573           the driver to get DMA-like performance when there are either
 574           no free DMA channels, or when doing transfers that required both
 575           TX and RX data paths.
 576
 577 config SPI_S3C64XX
 578         tristate "Samsung S3C64XX series type SPI"
 579         depends on (PLAT_SAMSUNG || ARCH_EXYNOS || COMPILE_TEST)
 580         help
 581           SPI driver for Samsung S3C64XX and newer SoCs.
 582
 583 config SPI_SC18IS602
 584         tristate "NXP SC18IS602/602B/603 I2C to SPI bridge"
 585         depends on I2C
 586         help
 587           SPI driver for NXP SC18IS602/602B/603 I2C to SPI bridge.
 588
 589 config SPI_SH_MSIOF
 590         tristate "SuperH MSIOF SPI controller"
 591         depends on HAVE_CLK && HAS_DMA
 592         depends on ARCH_SHMOBILE || ARCH_RENESAS || COMPILE_TEST
 593         help
 594           SPI driver for SuperH and SH Mobile MSIOF blocks.
 595
 596 config SPI_SH
 597         tristate "SuperH SPI controller"
 598         depends on SUPERH || COMPILE_TEST
 599         help
 600           SPI driver for SuperH SPI blocks.
 601
 602 config SPI_SH_SCI
 603         tristate "SuperH SCI SPI controller"
 604         depends on SUPERH
 605         select SPI_BITBANG
 606         help
 607           SPI driver for SuperH SCI blocks.
 608
 609 config SPI_SH_HSPI
 610         tristate "SuperH HSPI controller"
 611         depends on ARCH_RENESAS || COMPILE_TEST
 612         help
 613           SPI driver for SuperH HSPI blocks.
 614
 615 config SPI_SIRF
 616         tristate "CSR SiRFprimaII SPI controller"
 617         depends on SIRF_DMA
 618         select SPI_BITBANG
 619         help
 620           SPI driver for CSR SiRFprimaII SoCs
 621
 622 config SPI_ST_SSC4
 623         tristate "STMicroelectronics SPI SSC-based driver"
 624         depends on ARCH_STI || COMPILE_TEST
 625         help
 626           STMicroelectronics SoCs support for SPI. If you say yes to
 627           this option, support will be included for the SSC driven SPI.
 628
 629 config SPI_SUN4I
 630         tristate "Allwinner A10 SoCs SPI controller"
 631         depends on ARCH_SUNXI || COMPILE_TEST
 632         help
 633           SPI driver for Allwinner sun4i, sun5i and sun7i SoCs
 634
 635 config SPI_SUN6I
 636         tristate "Allwinner A31 SPI controller"
 637         depends on ARCH_SUNXI || COMPILE_TEST
 638         depends on RESET_CONTROLLER
 639         help
 640           This enables using the SPI controller on the Allwinner A31 SoCs.
 641
 642 config SPI_MXS
 643         tristate "Freescale MXS SPI controller"
 644         depends on ARCH_MXS
 645         select STMP_DEVICE
 646         help
 647           SPI driver for Freescale MXS devices.
 648
 649 config SPI_TEGRA114
 650         tristate "NVIDIA Tegra114 SPI Controller"
 651         depends on (ARCH_TEGRA && TEGRA20_APB_DMA) || COMPILE_TEST
 652         depends on RESET_CONTROLLER && HAS_DMA
 653         help
 654           SPI driver for NVIDIA Tegra114 SPI Controller interface. This controller
 655           is different than the older SoCs SPI controller and also register interface
 656           get changed with this controller.
 657
 658 config SPI_TEGRA20_SFLASH
 659         tristate "Nvidia Tegra20 Serial flash Controller"
 660         depends on ARCH_TEGRA || COMPILE_TEST
 661         depends on RESET_CONTROLLER
 662         help
 663           SPI driver for Nvidia Tegra20 Serial flash Controller interface.
 664           The main usecase of this controller is to use spi flash as boot
 665           device.
 666
 667 config SPI_TEGRA20_SLINK
 668         tristate "Nvidia Tegra20/Tegra30 SLINK Controller"
 669         depends on (ARCH_TEGRA && TEGRA20_APB_DMA) || COMPILE_TEST
 670         depends on RESET_CONTROLLER && HAS_DMA
 671         help
 672           SPI driver for Nvidia Tegra20/Tegra30 SLINK Controller interface.
 673
 674 config SPI_THUNDERX
 675         tristate "Cavium ThunderX SPI controller"
 676         depends on PCI && 64BIT && (ARM64 || COMPILE_TEST)
 677         help
 678           SPI host driver for the hardware found on Cavium ThunderX
 679           SOCs.
 680
 681 config SPI_TOPCLIFF_PCH
 682         tristate "Intel EG20T PCH/LAPIS Semicon IOH(ML7213/ML7223/ML7831) SPI"
 683         depends on PCI && (X86_32 || MIPS || COMPILE_TEST)
 684         help
 685           SPI driver for the Topcliff PCH (Platform Controller Hub) SPI bus
 686           used in some x86 embedded processors.
 687
 688           This driver also supports the ML7213/ML7223/ML7831, a companion chip
 689           for the Atom E6xx series and compatible with the Intel EG20T PCH.
 690
 691 config SPI_TXX9
 692         tristate "Toshiba TXx9 SPI controller"
 693         depends on GPIOLIB && (CPU_TX49XX || COMPILE_TEST)
 694         help
 695           SPI driver for Toshiba TXx9 MIPS SoCs
 696
 697 config SPI_XCOMM
 698         tristate "Analog Devices AD-FMCOMMS1-EBZ SPI-I2C-bridge driver"
 699         depends on I2C
 700         help
 701           Support for the SPI-I2C bridge found on the Analog Devices
 702           AD-FMCOMMS1-EBZ board.
 703
 704 config SPI_XILINX
 705         tristate "Xilinx SPI controller common module"
 706         depends on HAS_IOMEM
 707         select SPI_BITBANG
 708         help
 709           This exposes the SPI controller IP from the Xilinx EDK.
 710
 711           See the "OPB Serial Peripheral Interface (SPI) (v1.00e)"
 712           Product Specification document (DS464) for hardware details.
 713
 714           Or for the DS570, see "XPS Serial Peripheral Interface (SPI) (v2.00b)"
 715
 716 config SPI_XLP
 717         tristate "Netlogic XLP SPI controller driver"
 718         depends on CPU_XLP || ARCH_THUNDER2 || COMPILE_TEST
 719         help
 720           Enable support for the SPI controller on the Netlogic XLP SoCs.
 721           Currently supported XLP variants are XLP8XX, XLP3XX, XLP2XX, XLP9XX
 722           and XLP5XX.
 723
 724           If you have a Netlogic XLP platform say Y here.
 725           If unsure, say N.
 726
 727 config SPI_XTENSA_XTFPGA
 728         tristate "Xtensa SPI controller for xtfpga"
 729         depends on (XTENSA && XTENSA_PLATFORM_XTFPGA) || COMPILE_TEST
 730         select SPI_BITBANG
 731         help
 732           SPI driver for xtfpga SPI master controller.
 733
 734           This simple SPI master controller is built into xtfpga bitstreams
 735           and is used to control daughterboard audio codec. It always transfers
 736           16 bit words in SPI mode 0, automatically asserting CS on transfer
 737           start and deasserting on end.
 738
 739 config SPI_ZYNQMP_GQSPI
 740         tristate "Xilinx ZynqMP GQSPI controller"
 741         depends on SPI_MASTER && HAS_DMA
 742         help
 743           Enables Xilinx GQSPI controller driver for Zynq UltraScale+ MPSoC.
 744
 745 #
 746 # Add new SPI master controllers in alphabetical order above this line
 747 #
 748
 749 #
 750 # There are lots of SPI device types, with sensors and memory
 751 # being probably the most widely used ones.
 752 #
 753 comment "SPI Protocol Masters"
 754
 755 config SPI_SPIDEV
 756         tristate "User mode SPI device driver support"
 757         help
 758           This supports user mode SPI protocol drivers.
 759
 760           Note that this application programming interface is EXPERIMENTAL
 761           and hence SUBJECT TO CHANGE WITHOUT NOTICE while it stabilizes.
 762
 763 config SPI_LOOPBACK_TEST
 764         tristate "spi loopback test framework support"
 765         depends on m
 766         help
 767           This enables the SPI loopback testing framework driver
 768
 769           primarily used for development of spi_master drivers
 770           and to detect regressions
 771
 772 config SPI_TLE62X0
 773         tristate "Infineon TLE62X0 (for power switching)"
 774         depends on SYSFS
 775         help
 776           SPI driver for Infineon TLE62X0 series line driver chips,
 777           such as the TLE6220, TLE6230 and TLE6240.  This provides a
 778           sysfs interface, with each line presented as a kind of GPIO
 779           exposing both switch control and diagnostic feedback.
 780
 781 #
 782 # Add new SPI protocol masters in alphabetical order above this line
 783 #
 784
 785 endif # SPI_MASTER
 786
 787 # (slave support would go here)
 788
 789 endif # SPI