order. These are fe_int0, fe_int1 and fe_int2.
- clocks: the clock used by the core
- clock-names: the names of the clock listed in the clocks property. These are
- "ethif", "esw", "gp2", "gp1"
+ "ethif", "esw", "gp2", "gp1" : For MT2701 and MT7623 SoC
+ "ethif", "esw", "gp0", "gp1", "gp2", "sgmii_tx250m", "sgmii_rx250m",
+ "sgmii_cdr_ref", "sgmii_cdr_fb", "sgmii_ck", "eth2pll" : For MT7622 SoC
- power-domains: phandle to the power domain that the ethernet is part of
- - resets: Should contain a phandle to the ethsys reset signal
- - reset-names: Should contain the reset signal name "eth"
+ - resets: Should contain phandles to the ethsys reset signals
+ - reset-names: Should contain the names of reset signal listed in the resets
+ property
+ These are "fe", "gmac" and "ppe"
- mediatek,ethsys: phandle to the syscon node that handles the port setup
+- mediatek,sgmiisys: phandle to the syscon node that handles the SGMII setup
+ which is required for those SoCs equipped with SGMII such as MT7622 SoC.
- mediatek,pctl: phandle to the syscon node that handles the ports slew rate
and driver current
marvell,pcie-port = <2>;
marvell,pcie-lane = <0>;
clocks = <&gateclk 26>;
- status = "disabled";
};
- pcie@10,0 {
+ pcie@a,0 {
device_type = "pci";
assigned-addresses = <0x82005000 0 0x82000 0 0x2000>;
reg = <0x5000 0 0 0 0>;
ti,min-output-impedance;
interrupt-parent = <&gpio6>;
interrupts = <16 IRQ_TYPE_EDGE_FALLING>;
+ ti,dp83867-rxctrl-strap-quirk;
};
};
+
+ &mmc1 {
+ pinctrl-names = "default", "hs", "sdr12", "sdr25", "sdr50", "ddr50", "sdr104";
+ pinctrl-0 = <&mmc1_pins_default>;
+ pinctrl-1 = <&mmc1_pins_hs>;
+ pinctrl-2 = <&mmc1_pins_sdr12>;
+ pinctrl-3 = <&mmc1_pins_sdr25>;
+ pinctrl-4 = <&mmc1_pins_sdr50>;
+ pinctrl-5 = <&mmc1_pins_ddr50_rev20 &mmc1_iodelay_ddr50_conf>;
+ pinctrl-6 = <&mmc1_pins_sdr104 &mmc1_iodelay_sdr104_rev20_conf>;
+ vqmmc-supply = <&ldo1_reg>;
+ };
+
+ &mmc2 {
+ pinctrl-names = "default", "hs", "ddr_1_8v", "hs200_1_8v";
+ pinctrl-0 = <&mmc2_pins_default>;
+ pinctrl-1 = <&mmc2_pins_hs>;
+ pinctrl-2 = <&mmc2_pins_ddr_rev20 &mmc2_iodelay_ddr_conf>;
+ pinctrl-3 = <&mmc2_pins_hs200 &mmc2_iodelay_hs200_rev20_conf>;
+ vmmc-supply = <&evm_1v8_sw>;
+ };
>;
};
- pinctrl_pwm1: pwm1grp {
+ pinctrl_backlight: backlightgrp {
fsl,pins = <
- MX7D_PAD_LPSR_GPIO1_IO01__PWM1_OUT 0x110b0
+ MX7D_PAD_LPSR_GPIO1_IO01__GPIO1_IO1 0x110b0
>;
-
- pinctrl_spi4: spi4grp {
- fsl,pins = <
- MX7D_PAD_GPIO1_IO09__GPIO1_IO9 0x59
- MX7D_PAD_GPIO1_IO12__GPIO1_IO12 0x59
- MX7D_PAD_GPIO1_IO13__GPIO1_IO13 0x59
- >;
- };
};
};
stdout-path = "serial2:1500000n8";
};
+ dc_12v: dc-12v {
+ compatible = "regulator-fixed";
+ regulator-name = "dc_12v";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ };
+
+ vcc_sys: vcc-sys {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&dc_12v>;
+ };
++
+ vcc_phy: vcc-phy-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_phy";
+ regulator-always-on;
+ regulator-boot-on;
+ };
+};
+
+&gmac2phy {
+ phy-supply = <&vcc_phy>;
+ clock_in_out = "output";
+ assigned-clocks = <&cru SCLK_MAC2PHY_SRC>;
+ assigned-clock-rate = <50000000>;
+ assigned-clocks = <&cru SCLK_MAC2PHY>;
+ assigned-clock-parents = <&cru SCLK_MAC2PHY_SRC>;
+ status = "okay";
};
+ &i2c1 {
+ status = "okay";
+
+ rk805: rk805@18 {
+ compatible = "rockchip,rk805";
+ reg = <0x18>;
+ interrupt-parent = <&gpio2>;
+ interrupts = <6 IRQ_TYPE_LEVEL_LOW>;
+ #clock-cells = <1>;
+ clock-output-names = "xin32k", "rk805-clkout2";
+ gpio-controller;
+ #gpio-cells = <2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_int_l>;
+ rockchip,system-power-controller;
+ wakeup-source;
+
+ vcc1-supply = <&vcc_sys>;
+ vcc2-supply = <&vcc_sys>;
+ vcc3-supply = <&vcc_sys>;
+ vcc4-supply = <&vcc_sys>;
+ vcc5-supply = <&vcc_io>;
+ vcc6-supply = <&vcc_io>;
+
+ regulators {
+ vdd_logic: DCDC_REG1 {
+ regulator-name = "vdd_logic";
+ regulator-min-microvolt = <712500>;
+ regulator-max-microvolt = <1450000>;
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1000000>;
+ };
+ };
+
+ vdd_arm: DCDC_REG2 {
+ regulator-name = "vdd_arm";
+ regulator-min-microvolt = <712500>;
+ regulator-max-microvolt = <1450000>;
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <950000>;
+ };
+ };
+
+ vcc_ddr: DCDC_REG3 {
+ regulator-name = "vcc_ddr";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ vcc_io: DCDC_REG4 {
+ regulator-name = "vcc_io";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+
+ vcc_18: LDO_REG1 {
+ regulator-name = "vcc_18";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vcc18_emmc: LDO_REG2 {
+ regulator-name = "vcc18_emmc";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vdd_10: LDO_REG3 {
+ regulator-name = "vdd_10";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1000000>;
+ };
+ };
+ };
+ };
+ };
+
+ &pinctrl {
+ pmic {
+ pmic_int_l: pmic-int-l {
+ rockchip,pins = <2 RK_PA6 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+ };
+
+ &tsadc {
+ status = "okay";
+ };
+
&uart2 {
status = "okay";
};
status = "disabled";
};
+ gmac2phy: ethernet@ff550000 {
+ compatible = "rockchip,rk3328-gmac";
+ reg = <0x0 0xff550000 0x0 0x10000>;
+ rockchip,grf = <&grf>;
+ interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "macirq";
+ clocks = <&cru SCLK_MAC2PHY_SRC>, <&cru SCLK_MAC2PHY_RXTX>,
+ <&cru SCLK_MAC2PHY_RXTX>, <&cru SCLK_MAC2PHY_REF>,
+ <&cru ACLK_MAC2PHY>, <&cru PCLK_MAC2PHY>,
+ <&cru SCLK_MAC2PHY_OUT>;
+ clock-names = "stmmaceth", "mac_clk_rx",
+ "mac_clk_tx", "clk_mac_ref",
+ "aclk_mac", "pclk_mac",
+ "clk_macphy";
+ resets = <&cru SRST_GMAC2PHY_A>, <&cru SRST_MACPHY>;
+ reset-names = "stmmaceth", "mac-phy";
+ phy-mode = "rmii";
+ phy-handle = <&phy>;
+ status = "disabled";
+
+ mdio {
+ compatible = "snps,dwmac-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ phy: phy@0 {
+ compatible = "ethernet-phy-id1234.d400", "ethernet-phy-ieee802.3-c22";
+ reg = <0>;
+ clocks = <&cru SCLK_MAC2PHY_OUT>;
+ resets = <&cru SRST_MACPHY>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&fephyled_rxm1 &fephyled_linkm1>;
+ phy-is-integrated;
+ };
+ };
+ };
+
+ usb20_otg: usb@ff580000 {
+ compatible = "rockchip,rk3328-usb", "rockchip,rk3066-usb",
+ "snps,dwc2";
+ reg = <0x0 0xff580000 0x0 0x40000>;
+ interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru HCLK_OTG>;
+ clock-names = "otg";
+ dr_mode = "otg";
+ g-np-tx-fifo-size = <16>;
+ g-rx-fifo-size = <280>;
+ g-tx-fifo-size = <256 128 128 64 32 16>;
+ g-use-dma;
+ phys = <&u2phy_otg>;
+ phy-names = "usb2-phy";
+ status = "disabled";
+ };
+
+ usb_host0_ehci: usb@ff5c0000 {
+ compatible = "generic-ehci";
+ reg = <0x0 0xff5c0000 0x0 0x10000>;
+ interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru HCLK_HOST0>, <&u2phy>;
+ clock-names = "usbhost", "utmi";
+ phys = <&u2phy_host>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ usb_host0_ohci: usb@ff5d0000 {
+ compatible = "generic-ohci";
+ reg = <0x0 0xff5d0000 0x0 0x10000>;
+ interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru HCLK_HOST0>, <&u2phy>;
+ clock-names = "usbhost", "utmi";
+ phys = <&u2phy_host>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
gic: interrupt-controller@ff811000 {
compatible = "arm,gic-400";
#interrupt-cells = <3>;
projects / mirror_ubuntu-bionic-kernel.git / commitdiff