Dirk Gouders reported that two consecutive "make" invocations on an
already compiled tree will show alternating behaviors:
$ make
CALL scripts/checksyscalls.sh
DESCEND objtool
CHK include/generated/compile.h
DATAREL arch/x86/boot/compressed/vmlinux
Kernel: arch/x86/boot/bzImage is ready (#48)
Building modules, stage 2.
MODPOST 165 modules
$ make
CALL scripts/checksyscalls.sh
DESCEND objtool
CHK include/generated/compile.h
LD arch/x86/boot/compressed/vmlinux
ZOFFSET arch/x86/boot/zoffset.h
AS arch/x86/boot/header.o
LD arch/x86/boot/setup.elf
OBJCOPY arch/x86/boot/setup.bin
OBJCOPY arch/x86/boot/vmlinux.bin
BUILD arch/x86/boot/bzImage
Setup is 15644 bytes (padded to 15872 bytes).
System is 6663 kB
CRC 3eb90f40
Kernel: arch/x86/boot/bzImage is ready (#48)
Building modules, stage 2.
MODPOST 165 modules
He bisected it back to:
commit 98f78525371b ("x86/boot: Refuse to build with data relocations")
The root cause was the use of the "if_changed" kbuild function multiple
times for the same target. It was designed to only be used once per
target, otherwise it will effectively always trigger, flipping back and
forth between the two commands getting recorded by "if_changed". Instead,
this patch merges the two commands into a single function to get stable
build artifacts (i.e. .vmlinux.cmd), and a single build behavior.
NO_RT_RUNTIME_SHARE feature is used to prevent a CPU borrow enough
runtime with a spin-rt-task.
However, if RT_RUNTIME_SHARE feature is enabled and rt_rq has borrowd
enough rt_runtime at the beginning, rt_runtime can't be restored to
its initial bandwidth rt_runtime after we disable RT_RUNTIME_SHARE.
E.g. on my PC with 4 cores, procedure to reproduce:
1) Make sure RT_RUNTIME_SHARE is enabled
cat /sys/kernel/debug/sched_features
GENTLE_FAIR_SLEEPERS START_DEBIT NO_NEXT_BUDDY LAST_BUDDY
CACHE_HOT_BUDDY WAKEUP_PREEMPTION NO_HRTICK NO_DOUBLE_TICK
LB_BIAS NONTASK_CAPACITY TTWU_QUEUE NO_SIS_AVG_CPU SIS_PROP
NO_WARN_DOUBLE_CLOCK RT_PUSH_IPI RT_RUNTIME_SHARE NO_LB_MIN
ATTACH_AGE_LOAD WA_IDLE WA_WEIGHT WA_BIAS
2) Start a spin-rt-task
./loop_rr &
3) set affinity to the last cpu
taskset -p 8 $pid_of_loop_rr
4) Observe that last cpu have borrowed enough runtime.
cat /proc/sched_debug | grep rt_runtime
.rt_runtime : 950.000000
.rt_runtime : 900.000000
.rt_runtime : 950.000000
.rt_runtime : 1000.000000
5) Disable RT_RUNTIME_SHARE
echo NO_RT_RUNTIME_SHARE > /sys/kernel/debug/sched_features
6) Observe that rt_runtime can not been restored
cat /proc/sched_debug | grep rt_runtime
.rt_runtime : 950.000000
.rt_runtime : 900.000000
.rt_runtime : 950.000000
.rt_runtime : 1000.000000
This patch help to restore rt_runtime after we disable
RT_RUNTIME_SHARE.
Signed-off-by: Hailong Liu <liu.hailong6@zte.com.cn> Signed-off-by: Jiang Biao <jiang.biao2@zte.com.cn> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: zhong.weidong@zte.com.cn Link: http://lkml.kernel.org/r/1531874815-39357-1-git-send-email-liu.hailong6@zte.com.cn Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Rx hash/filter table configuration uses rss_conf_obj to configure filters
in the hardware. This object is initialized only when the interface is
brought up.
This patch adds driver changes to configure rss params only when the device
is in opened state. In port disabled case, the config will be cached in the
driver structure which will be applied in the successive load path.
Please consider applying it to 'net' branch.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Including asm/cacheflush.h first results in the following build error
when trying to build sparc32:allmodconfig, because 'struct page' has not
been declared, and the function declaration ends up creating a separate
(private) declaration of struct page (as a result of function arguments
being in the scope of the function declaration and definition, not in
global scope).
The C scoping rules do not just affect variable visibility, they also
affect type declaration visibility.
The end result is that when the actual call site is seen in
<linux/highmem.h>, the 'struct page' type in the caller is not the same
'struct page' that the function was declared with, resulting in:
In file included from arch/sparc/include/asm/page.h:10:0,
...
from drivers/staging/media/omap4iss/iss_video.c:15:
include/linux/highmem.h: In function 'clear_user_highpage':
include/linux/highmem.h:137:31: error:
passing argument 1 of 'sparc_flush_page_to_ram' from incompatible
pointer type
Include generic includes files first to fix the problem.
Fixes: fc96d58c10162 ("[media] v4l: omap4iss: Add support for OMAP4 camera interface - Video devices") Suggested-by: Linus Torvalds <torvalds@linux-foundation.org> Acked-by: David S. Miller <davem@davemloft.net> Cc: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Guenter Roeck <linux@roeck-us.net>
[ Added explanation of C scope rules - Linus ] Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
of_iomap() can return NULL so that return needs to be checked and NULL
treated as failure. While at it also take care of the missing
of_node_put() in the error path.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org> Fixes: commit afa17a500a36 ("net/can: add driver for mscan family & mpc52xx_mscan") Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Prevent drivers from building on PPC32 if they use isa_bus_to_virt(),
isa_virt_to_bus(), or isa_page_to_bus(), which are not available and
thus cause build errors.
../drivers/net/ethernet/3com/3c515.c: In function 'corkscrew_open':
../drivers/net/ethernet/3com/3c515.c:824:9: error: implicit declaration of function 'isa_virt_to_bus'; did you mean 'virt_to_bus'? [-Werror=implicit-function-declaration]
../drivers/net/ethernet/amd/lance.c: In function 'lance_rx':
../drivers/net/ethernet/amd/lance.c:1203:23: error: implicit declaration of function 'isa_bus_to_virt'; did you mean 'bus_to_virt'? [-Werror=implicit-function-declaration]
../drivers/net/ethernet/amd/ni65.c: In function 'ni65_init_lance':
../drivers/net/ethernet/amd/ni65.c:585:20: error: implicit declaration of function 'isa_virt_to_bus'; did you mean 'virt_to_bus'? [-Werror=implicit-function-declaration]
../drivers/net/ethernet/cirrus/cs89x0.c: In function 'net_open':
../drivers/net/ethernet/cirrus/cs89x0.c:897:20: error: implicit declaration of function 'isa_virt_to_bus'; did you mean 'virt_to_bus'? [-Werror=implicit-function-declaration]
Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Suggested-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The bad access is in neigh_hh_output(), at skb->data - 16 (HH_DATA_MOD).
atl1c driver provided skb with no headroom, so 14 bytes (ethernet
header) got pulled, but then 16 are copied.
Reserve NET_SKB_PAD bytes headroom, like netdev_alloc_skb().
Compile tested only; I lack hardware.
Fixes: 7b7017642199 ("atl1c: Fix misuse of netdev_alloc_skb in refilling rx ring") Signed-off-by: Florian Westphal <fw@strlen.de> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
There's a possible race where driver can read link status in mid-transition
and see that virtual-link is up yet speed is 0. Since in this
mid-transition we're guaranteed to see a mailbox from MFW soon, we can
afford to treat this as link down.
Fixes: cc875c2e ("qed: Add link support") Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com> Signed-off-by: Ariel Elior <ariel.elior@cavium.com> Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Apparently, MFW publishes EEE capabilities even for Fiber-boards that don't
support them, and later since qed internally sets adv_caps it would cause
link-flap avoidance (LFA) to fail when driver would initiate the link.
This in turn delays the link, causing traffic to fail.
Driver has been modified to not to ask MFW for any EEE config if EEE isn't
to be enabled.
Fixes: 645874e5 ("qed: Add support for Energy efficient ethernet.") Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com> Signed-off-by: Ariel Elior <ariel.elior@cavium.com> Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Do not expose the address of vmx->nested.current_vmptr to
kvm_write_guest_virt_system() as the resulting __copy_to_user()
call will trigger a WARN when CONFIG_HARDENED_USERCOPY is
enabled.
Opportunistically clean up variable names in handle_vmptrst()
to improve readability, e.g. vmcs_gva is misleading as the
memory operand of VMPTRST is plain memory, not a VMCS.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com> Tested-by: Peter Shier <pshier@google.com> Reviewed-by: Peter Shier <pshier@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Its possible to rename two chains to the same name in one
transaction:
nft add chain t c1
nft add chain t c2
nft 'rename chain t c1 c3;rename chain t c2 c3'
This creates two chains named 'c3'.
Appears to be harmless, both chains can still be deleted both
by name or handle, but, nevertheless, its a bug.
Walk transaction log and also compare vs. the pending renames.
Both chains can still be deleted, but nevertheless it is a bug as
we don't allow to create chains with identical names, so we should
prevent this from happening-by-rename too.
Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The new name is stored in the transaction metadata, on commit,
the pointers to the old and new names are swapped.
Therefore in abort and commit case we have to free the
pointer in the chain_trans container.
In commit case, the pointer can be used by another cpu that
is currently dumping the renamed chain, thus kfree needs to
happen after waiting for rcu readers to complete.
Fixes: b7263e071a ("netfilter: nf_tables: Allow chain name of up to 255 chars") Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
None of the JITs is allowed to implement exit paths from the BPF
insn mappings other than BPF_JMP | BPF_EXIT. In the BPF core code
we have a couple of rewrites in eBPF (e.g. LD_ABS / LD_IND) and
in eBPF to cBPF translation to retain old existing behavior where
exceptions may occur; they are also tightly controlled by the
verifier where it disallows some of the features such as BPF to
BPF calls when legacy LD_ABS / LD_IND ops are present in the BPF
program. During recent review of all BPF_XADD JIT implementations
I noticed that the ppc64 one is buggy in that it contains two
jumps to exit paths. This is problematic as this can bypass verifier
expectations e.g. pointed out in commit f6b1b3bf0d5f ("bpf: fix
subprog verifier bypass by div/mod by 0 exception"). The first
exit path is obsoleted by the fix in ca36960211eb ("bpf: allow xadd
only on aligned memory") anyway, and for the second one we need to
do a fetch, add and store loop if the reservation from lwarx/ldarx
was lost in the meantime.
Fixes: 156d0e290e96 ("powerpc/ebpf/jit: Implement JIT compiler for extended BPF") Reviewed-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> Reviewed-by: Sandipan Das <sandipan@linux.vnet.ibm.com> Tested-by: Sandipan Das <sandipan@linux.vnet.ibm.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
GC of set uses call_rcu() to destroy elements.
So that elements would be destroyed after destroying sets and chains.
But, elements should be destroyed before destroying sets and chains.
In order to wait calling call_rcu(), a rcu_barrier() is added.
In order to test correctly, below patch should be applied.
https://patchwork.ozlabs.org/patch/940883/
The list [1] of commits doing endianness fixes in USB subsystem is long
due to below quote from USB spec Revision 2.0 from April 27, 2000:
------------
8.1 Byte/Bit Ordering
Multiple byte fields in standard descriptors, requests, and responses
are interpreted as and moved over the bus in little-endian order, i.e.
LSB to MSB.
------------
This commit belongs to the same family.
[1] Example of endianness fixes in USB subsystem:
commit 14e1d56cbea6 ("usb: gadget: f_uac2: endianness fixes.")
commit 42370b821168 ("usb: gadget: f_uac1: endianness fixes.")
commit 63afd5cc7877 ("USB: chaoskey: fix Alea quirk on big-endian hosts")
commit 74098c4ac782 ("usb: gadget: acm: fix endianness in notifications")
commit cdd7928df0d2 ("ACM gadget: fix endianness in notifications")
commit 323ece54e076 ("cdc-wdm: fix endianness bug in debug statements")
commit e102609f1072 ("usb: gadget: uvc: Fix endianness mismatches")
list goes on
Fixes: 132fcb460839 ("usb: gadget: Add Audio Class 2.0 Driver") Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com> Reviewed-by: Ruslan Bilovol <ruslan.bilovol@gmail.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The tools/usb/ffs-test.c file defines cpu_to_le16/32 by using the C
library htole16/32 function calls. However, cpu_to_le16/32 are used when
initializing structures, i.e in a context where a function call is not
allowed.
It works fine on little endian systems because htole16/32 are defined by
the C library as no-ops. But on big-endian systems, they are actually
doing something, which might involve calling a function, causing build
failures, such as:
ffs-test.c:48:25: error: initializer element is not constant
#define cpu_to_le32(x) htole32(x)
^~~~~~~
ffs-test.c:128:12: note: in expansion of macro ‘cpu_to_le32’
.magic = cpu_to_le32(FUNCTIONFS_DESCRIPTORS_MAGIC_V2),
^~~~~~~~~~~
To solve this, we code cpu_to_le16/32 in a way that allows them to be
used when initializing structures. This fix was imported from
meta-openembedded/android-tools/fix-big-endian-build.patch written by
Thomas Petazzoni <thomas.petazzoni@free-electrons.com>.
CC: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Fix build errors when built for PPC64:
These variables are only used on PPC32 so they don't need to be
initialized for PPC64.
../drivers/usb/phy/phy-fsl-usb.c: In function 'usb_otg_start':
../drivers/usb/phy/phy-fsl-usb.c:865:3: error: '_fsl_readl' undeclared (first use in this function); did you mean 'fsl_readl'?
_fsl_readl = _fsl_readl_be;
../drivers/usb/phy/phy-fsl-usb.c:865:16: error: '_fsl_readl_be' undeclared (first use in this function); did you mean 'fsl_readl'?
_fsl_readl = _fsl_readl_be;
../drivers/usb/phy/phy-fsl-usb.c:866:3: error: '_fsl_writel' undeclared (first use in this function); did you mean 'fsl_writel'?
_fsl_writel = _fsl_writel_be;
../drivers/usb/phy/phy-fsl-usb.c:866:17: error: '_fsl_writel_be' undeclared (first use in this function); did you mean 'fsl_writel'?
_fsl_writel = _fsl_writel_be;
../drivers/usb/phy/phy-fsl-usb.c:868:16: error: '_fsl_readl_le' undeclared (first use in this function); did you mean 'fsl_readl'?
_fsl_readl = _fsl_readl_le;
../drivers/usb/phy/phy-fsl-usb.c:869:17: error: '_fsl_writel_le' undeclared (first use in this function); did you mean 'fsl_writel'?
_fsl_writel = _fsl_writel_le;
and the sysfs "show" function return type should be ssize_t, not int:
The change protects almost the whole body of u_audio_iso_complete()
function by PCM stream lock, this is mainly sufficient to avoid a race
between USB request completion and stream termination, the change
prevents a possibility of invalid memory access in interrupt context
by memcpy():
Also added a check for potential !runtime condition, commonly it is
done by PCM_RUNTIME_CHECK(substream) in the beginning, however this
does not completely prevent from oopses in u_audio_iso_complete(),
because the proper protection scheme must be implemented in PCM
library functions.
An example of *not fixed* oops due to substream->runtime->*
dereference by snd_pcm_running(substream) from
snd_pcm_period_elapsed(), where substream->runtime is gone while
waiting the substream lock:
Unable to handle kernel paging request at virtual address 6b6b6b6b
pgd = db7e4000
[6b6b6b6b] *pgd=00000000
CPU: 0 PID: 193 Comm: klogd Tainted: G C 3.14.54+ #118
task: db5ac500 ti: db60c000 task.ti: db60c000
PC is at snd_pcm_period_elapsed+0x48/0xd8 [snd_pcm]
LR is at snd_pcm_period_elapsed+0x40/0xd8 [snd_pcm]
pc : [<>] lr : [<>] psr: 60000193
Flags: nZCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment user
Control: 10c5387d Table: 2b7e404a DAC: 00000015
Process klogd (pid: 193, stack limit = 0xdb60c238)
[<>] (snd_pcm_period_elapsed [snd_pcm]) from [<>] (udc_irq+0x500/0xbbc)
[<>] (udc_irq) from [<>] (ci_irq+0x280/0x304)
[<>] (ci_irq) from [<>] (handle_irq_event_percpu+0xa4/0x40c)
[<>] (handle_irq_event_percpu) from [<>] (handle_irq_event+0x3c/0x5c)
[<>] (handle_irq_event) from [<>] (handle_fasteoi_irq+0xc4/0x110)
[<>] (handle_fasteoi_irq) from [<>] (generic_handle_irq+0x20/0x30)
[<>] (generic_handle_irq) from [<>] (handle_IRQ+0x80/0xc0)
[<>] (handle_IRQ) from [<>] (gic_handle_irq+0x3c/0x60)
[<>] (gic_handle_irq) from [<>] (__irq_svc+0x44/0x78)
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
[erosca: W/o this patch, with minimal instrumentation [1], I can
consistently reproduce BUG: KASAN: use-after-free [2]]
[1] Instrumentation to reproduce issue [2]:
# diff --git a/drivers/usb/gadget/function/u_audio.c b/drivers/usb/gadget/function/u_audio.c
# index a72295c953bb..bd0b308024fe 100644
# --- a/drivers/usb/gadget/function/u_audio.c
# +++ b/drivers/usb/gadget/function/u_audio.c
# @@ -16,6 +16,7 @@
# #include <sound/core.h>
# #include <sound/pcm.h>
# #include <sound/pcm_params.h>
# +#include <linux/delay.h>
#
# #include "u_audio.h"
#
# @@ -147,6 +148,8 @@ static void u_audio_iso_complete(struct usb_ep *ep, struct usb_request *req)
#
# spin_unlock_irqrestore(&prm->lock, flags);
#
# + udelay(500); //delay here to increase probability of parallel activities
# +
# /* Pack USB load in ALSA ring buffer */
# pending = prm->dma_bytes - hw_ptr;
[2] After applying [1], below BUG occurs on Rcar-H3-Salvator-X board:
==================================================================
BUG: KASAN: use-after-free in u_audio_iso_complete+0x24c/0x520 [u_audio]
Read of size 8 at addr ffff8006cafcc248 by task swapper/0/0
Substream period size potentially can be changed in runtime, however
this is not accounted in the data copying routine, the change replaces
the cached value with an actual value from substream runtime.
As a side effect the change also removes a potential division by zero
in u_audio_iso_complete() function, if there is a race with
uac_pcm_hw_free(), which sets prm->period_size to 0.
Fixes: 132fcb460839 ("usb: gadget: Add Audio Class 2.0 Driver") Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com> Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
There is no necessity to copy PCM stream ring buffer area and size
properties to UAC private data structure, these values can be got
from substream itself.
The change gives more control on substream and avoid stale caching.
Fixes: 132fcb460839 ("usb: gadget: Add Audio Class 2.0 Driver") Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com> Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
In u_audio_iso_complete, the runtime hw_ptr is updated before the
data is actually copied over to/from the buffer/dma area. When
ALSA uses this hw_ptr, the data may not actually be available to
be used. This causes trash/stale audio to play/record. This
patch updates the hw_ptr after the data has been copied to avoid
this.
Fixes: 132fcb460839 ("usb: gadget: Add Audio Class 2.0 Driver") Signed-off-by: Joshua Frkuska <joshua_frkuska@mentor.com> Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Fix below smatch (v0.5.0-4443-g69e9094e11c1) warnings:
drivers/usb/gadget/function/u_audio.c:607 g_audio_setup() warn: strcpy() 'pcm_name' of unknown size might be too large for 'pcm->name'
drivers/usb/gadget/function/u_audio.c:614 g_audio_setup() warn: strcpy() 'card_name' of unknown size might be too large for 'card->driver'
drivers/usb/gadget/function/u_audio.c:615 g_audio_setup() warn: strcpy() 'card_name' of unknown size might be too large for 'card->shortname'
Below commits performed a similar 's/strcpy/strlcpy/' rework:
* v2.6.31 commit 8372d4980fbc ("ALSA: ctxfi - Fix PCM device naming")
* v4.14 commit 003d3e70dbeb ("ALSA: ad1848: fix format string overflow warning")
* v4.14 commit 6d8b04de87e1 ("ALSA: cs423x: fix format string overflow warning")
Fixes: eb9fecb9e69b ("usb: gadget: f_uac2: split out audio core") Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
If usb_ep_autoconfig() fails (i.e. returns a null endpoint descriptor),
we expect afunc_bind() to fail (i.e. return a negative error code).
However, due to v4.10-rc1 commit f1d3861d63a5 ("usb: gadget: f_uac2: fix
error handling at afunc_bind"), afunc_bind() returns zero, telling the
caller that it succeeded. This then generates NULL pointer dereference
in below scenario on Rcar H3-ES20-Salvator-X target:
After this patch is applied, the issue is fixed:
rcar-gen3:/home/root# modprobe g_audio
[ 59.217127] g_audio gadget: afunc_bind:565 Error!
[ 59.222329] g_audio ee020000.usb: failed to start g_audio: -19
modprobe: ERROR: could not insert 'g_audio': No such device
rcar-gen3:/home/root# modprobe -r g_audio
rcar-gen3:/home/root#
Fixes: f1d3861d63a5 ("usb: gadget: f_uac2: fix error handling at afunc_bind") Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
If the server or network is misbehaving and we get an unexpected reply
we can sometimes miss the request not being started and wait on a
request and never get a response, or even double complete the same
request. Fix this by replacing the send_complete completion with just a
per command lock. Add a per command cookie as well so that we can know
if we're getting a double completion for a previous event. Also check
to make sure we dont have REQUEUED set as that means we raced with the
timeout handler and need to just let the retry occur.
Signed-off-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
We can race with the snd timeout and the per-request timeout and end up
requeuing the same request twice. We can't use the send_complete
completion to tell if everything is ok because we hold the tx_lock
during send, so the timeout stuff will block waiting to mark the socket
dead, and we could be marked complete and still requeue. Instead add a
flag to the socket so we know whether we've been requeued yet.
Signed-off-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The LVDS signal integrity is only guaranteed when the correct enable
sequence (first IPU DI, then LDB) is used. If the LDB display output was
active before the imx-drm driver is loaded (like when a bootsplash was
active) the DI will be disabled by the full IPU reset we do when loading
the driver. The LDB control registers are not part of the IPU range and
thus will remain unchanged.
This leads to the LDB still being active when the DI is getting enabled,
effectively reversing the required enable sequence. Fix this by also
disabling the LDB on driver bind.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Transport drivers allocate memory for iSCSI hdr in alloc_pdu() and assign
it to task->hdr. In case of TMF task->hdr will be NULL resulting in NULL
pointer dereference.
2. ISCSI_OP_SCSI_DATA_OUT - In this case transport driver can free the
memory for iSCSI hdr after transmitting the pdu so task->hdr can be NULL or
invalid.
This patch fixes this issue by removing task->hdr->opcode from the printk
statement.
Signed-off-by: Varun Prakash <varun@chelsio.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The bridge loses its hw state when the cable is unplugged. If we detect
this case in the hpd handler, reset its state.
Reported-by: Rob Clark <robdclark@gmail.com> Tested-by: Rob Clark <robdclark@gmail.com> Reviewed-by: Archit Taneja <architt@codeaurora.org> Signed-off-by: Sean Paul <seanpaul@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20180703165648.120401-1-seanpaul@chromium.org Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
I was looking at usually suppressed gcc warnings,
[-Wimplicit-fallthrough=] in this case:
The code definitely looks like a break is missing here.
However I am not able to test the NL80211_IFTYPE_MESH_POINT,
nor do I actually know what might be :)
So please use this patch with caution and only if you are
able to do some testing.
Signed-off-by: Bernd Edlinger <bernd.edlinger@hotmail.de>
[johannes: looks obvious enough to apply as is, interesting
though that it never seems to have been a problem] Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Previously, when an MMP-protected file system is remounted read-only,
the kmmpd thread would exit the next time it woke up (a few seconds
later), without resetting the MMP sequence number back to
EXT4_MMP_SEQ_CLEAN.
Fix this by explicitly killing the MMP thread when the file system is
remounted read-only.
Signed-off-by: Theodore Ts'o <tytso@mit.edu> Cc: Andreas Dilger <adilger@dilger.ca> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
As part of hw reconfig, only stations linked to AP interfaces are added
back to the driver ignoring those which are tied to AP_VLAN interfaces.
It is true that there could be stations tied to the AP_VLAN interface while
serving 4addr clients or when using AP_VLAN for VLAN operations; we should
be adding these stations back to the driver as part of hw reconfig, failing
to do so can cause functional issues.
In the case of ath10k driver, the following errors were observed.
This ought to be an omission in e6194923237 ("esp: Fix memleaks on error
paths."). The memleak on error path in esp6_input is similar to esp_input
of esp4.
Fixes: e6194923237 ("esp: Fix memleaks on error paths.") Fixes: 3f29770723f ("ipsec: check return value of skb_to_sgvec always") Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Fix missing dst_release() when local broadcast or multicast traffic is
xfrm policy blocked.
For IPv4 this results to dst leak: ip_route_output_flow() allocates
dst_entry via __ip_route_output_key() and passes it to
xfrm_lookup_route(). xfrm_lookup returns ERR_PTR(-EPERM) that is
propagated. The dst that was allocated is never released.
IPv4 local broadcast testcase:
ping -b 192.168.1.255 &
sleep 1
ip xfrm policy add src 0.0.0.0/0 dst 192.168.1.255/32 dir out action block
IPv4 multicast testcase:
ping 224.0.0.1 &
sleep 1
ip xfrm policy add src 0.0.0.0/0 dst 224.0.0.1/32 dir out action block
For IPv6 the missing dst_release() causes trouble e.g. when used in netns:
ip netns add TEST
ip netns exec TEST ip link set lo up
ip link add dummy0 type dummy
ip link set dev dummy0 netns TEST
ip netns exec TEST ip addr add fd00::1111 dev dummy0
ip netns exec TEST ip link set dummy0 up
ip netns exec TEST ping -6 -c 5 ff02::1%dummy0 &
sleep 1
ip netns exec TEST ip xfrm policy add src ::/0 dst ff02::1 dir out action block
wait
ip netns del TEST
After netns deletion we see:
[ 258.239097] unregister_netdevice: waiting for lo to become free. Usage count = 2
[ 268.279061] unregister_netdevice: waiting for lo to become free. Usage count = 2
[ 278.367018] unregister_netdevice: waiting for lo to become free. Usage count = 2
[ 288.375259] unregister_netdevice: waiting for lo to become free. Usage count = 2
Fixes: ac37e2515c1a ("xfrm: release dst_orig in case of error in xfrm_lookup()") Signed-off-by: Tommi Rantala <tommi.t.rantala@nokia.com> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
mdio_bus: Fix use-after-free on device_register fails
KASAN has found use-after-free in fixed_mdio_bus_init,
commit 0c692d07842a ("drivers/net/phy/mdio_bus.c: call
put_device on device_register() failure") call put_device()
while device_register() fails,give up the last reference
to the device and allow mdiobus_release to be executed
,kfreeing the bus. However in most drives, mdiobus_free
be called to free the bus while mdiobus_register fails.
use-after-free occurs when access bus again, this patch
revert it to let mdiobus_free free the bus.
KASAN report details as below:
BUG: KASAN: use-after-free in mdiobus_free+0x85/0x90 drivers/net/phy/mdio_bus.c:482
Read of size 4 at addr ffff8881dc824d78 by task syz-executor.0/3524
Memory state around the buggy address: ffff8881dc824c00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff8881dc824c80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
>ffff8881dc824d00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^ ffff8881dc824d80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff8881dc824e00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
Fixes: 0c692d07842a ("drivers/net/phy/mdio_bus.c: call put_device on device_register() failure") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
(cherry picked from commit 6ff7b060535e87c2ae14dd8548512abfdda528fb)
CVE-2019-12819 Signed-off-by: Benjamin M Romer <benjamin.romer@canonical.com> Acked-by: Tyler Hicks <tyhicks@canonical.com> Acked-by: Po-Hsu Lin <po-hsu.lin@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
BugLink: https://bugs.launchpad.net/bugs/1824690
Downgrade "Unsupported event" message from dev_err to dev_dbg. Otherwise it
floods with this message one some platforms.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Signed-off-by: Zhang Rui <rui.zhang@intel.com>
(backported from commit 44c0c23725a16c8803b8809b87651405e8741e4d) Signed-off-by: Colin Ian King <colin.king@canonical.com> Acked-by: You-Sheng Yang <vicamo.yang@canonical.com> Acked-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Commit 26112ddc254c (PCI / ACPI / PM: Resume bridges w/o drivers on
suspend-to-RAM) attempted to fix a functional regression resulting
from commit c62ec4610c40 (PM / core: Fix direct_complete handling
for devices with no callbacks) by resuming PCI bridges without
drivers (that is, "parallel PCI" ones) during system-wide suspend if
the target system state is not ACPI S0 (working state).
That turns out insufficient, however, as it is reported that, at
least in one case, the platform firmware gets confused if a PCIe
root port is suspended before entering the ACPI S3 sleep state.
That issue was exposed by commit 77b3729ca03 (PCI / PM: Use
SMART_SUSPEND and LEAVE_SUSPENDED flags for PCIe ports) that allowed
PCIe ports to stay in runtime suspend during system-wide suspend
(which is OK for suspend-to-idle, but turns out to be problematic
otherwise).
For this reason, drop the driver check from acpi_pci_need_resume()
and resume all bridges (including PCIe ports with drivers) during
system-wide suspend if the target system state is not ACPI S0.
[If the target system state is ACPI S0, it means suspend-to-idle
and the platform firmware is not going to be invoked to actually
suspend the system, so there is no need to resume the bridges in
that case.]
Fixes: 77b3729ca03 (PCI / PM: Use SMART_SUSPEND and LEAVE_SUSPENDED flags for PCIe ports) Link: https://bugzilla.kernel.org/show_bug.cgi?id=200675 Reported-by: teika kazura <teika@gmx.com> Tested-by: teika kazura <teika@gmx.com> Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com> Acked-by: Bjorn Helgaas <bhelgaas@google.com> Cc: 4.16+ <stable@vger.kernel.org> # 4.16+: 26112ddc254c (PCI / ACPI / PM: Resume bridges ...) Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The vm_area_struct is one of the most fundamental memory management
objects, but the management of it is entirely open-coded evertwhere,
ranging from allocation and freeing (using kmem_cache_[z]alloc and
kmem_cache_free) to initializing all the fields.
We want to unify this in order to end up having some unified
initialization of the vmas, and the first step to this is to at least
have basic allocation functions.
Right now those functions are literally just wrappers around the
kmem_cache_*() calls. This is a purely mechanical conversion:
# new vma:
kmem_cache_zalloc(vm_area_cachep, GFP_KERNEL) -> vm_area_alloc()
# copy old vma
kmem_cache_alloc(vm_area_cachep, GFP_KERNEL) -> vm_area_dup(old)
to the point where the old vma passed in to the vm_area_dup() function
isn't even used yet (because I've left all the old manual initialization
alone).
It turned out that pci_remap_iospace() wasn't undone when the driver's
probe failed, and since devm_phy_optional_get() returned -EPROBE_DEFER,
the probe was retried, finally causing the BUG due to trying to remap
already remapped pages.
The V3 Semiconductor PCI driver has the same issue.
Replace devm_pci_remap_iospace() with its devm_ managed version to fix
the bug.
It turned out that pci_remap_iospace() wasn't undone when the driver's
probe failed, and since devm_phy_optional_get() returned -EPROBE_DEFER,
the probe was retried, finally causing the BUG due to trying to remap
already remapped pages.
The MediaTek PCIe driver has the same issue.
Replace devm_pci_remap_iospace() with its devm_ managed counterpart
to fix the bug.
It turned out that pci_remap_iospace() wasn't undone when the driver's
probe failed, and since devm_phy_optional_get() returned -EPROBE_DEFER,
the probe was retried, finally causing the BUG due to trying to remap
already remapped pages.
The Faraday PCI driver has the same issue. Replace pci_remap_iospace()
with its devm_ managed version to fix the bug.
It turned out that pci_remap_iospace() wasn't undone when the driver's
probe failed, and since devm_phy_optional_get() returned -EPROBE_DEFER,
the probe was retried, finally causing the BUG due to trying to remap
already remapped pages.
The Aardvark PCI controller driver has the same issue.
Replace pci_remap_iospace() with its devm_ managed version to fix the bug.
It turned out that pci_remap_iospace() wasn't undone when the driver's
probe failed, and since devm_phy_optional_get() returned -EPROBE_DEFER,
the probe was retried, finally causing the BUG due to trying to remap
already remapped pages.
The DesignWare PCIe controller driver has the same issue.
Replace devm_pci_remap_iospace() with a devm_ managed version to fix the
bug.
Fixes: cbce7900598c ("PCI: designware: Make driver arch-agnostic") Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
[lorenzo.pieralisi@arm.com: updated the commit log] Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Jingoo Han <jingoohan1@gmail.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
It turned out that pci_remap_iospace() wasn't undone when the driver's
probe failed, and since devm_phy_optional_get() returned -EPROBE_DEFER,
the probe was retried, finally causing the BUG due to trying to remap
already remapped pages.
The X-Gene PCI controller driver has the same issue.
Replace pci_remap_iospace() with the devm_ managed version so that the
pages get unmapped automagically on any probe failure.
During clc handshake the receive timeout is set to CLC_WAIT_TIME.
Remember and reset the original timeout value after the receive calls,
and remove a duplicate assignment of CLC_WAIT_TIME.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Signed-off-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
During a device failover, there may be latency between the loss
of the current backing device and a notification from firmware that
a failover has occurred. This latency can result in a large amount of
error printouts as firmware returns outgoing traffic with a generic
error code. These are not necessarily errors in this case as the
firmware is busy swapping in a new backing adapter and is not ready
to send packets yet. This patch reclassifies those error codes as
warnings with an explanation that a failover may be pending. All
other return codes will be considered errors.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Commit 0c3b7e42616f ("tools build: Add support for host programs format")
introduced host_c_flags which referenced CHOSTFLAGS. The actual name of the
variable is HOSTCFLAGS. Fix this up.
Fixes: 0c3b7e42616f ("tools build: Add support for host programs format") Signed-off-by: Laura Abbott <labbott@redhat.com> Acked-by: Jiri Olsa <jolsa@kernel.org> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
[Why]
When a dce100 asic was suspended, the clocks were not set to 0.
Upon resume, the new clock was compared to the existing clock,
they were found to be the same, and so the clock was not set.
This resulted in a pernicious blackscreen.
[How]
In atomic commit, check to see if there are any active pipes.
If no, set clocks to 0
Signed-off-by: David Francis <David.Francis@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
We fail to correctly clean up after a bus registration failure, which
can lead to an incorrect assumption about the registration state of
the upstream or sfp cage.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Builds started failing in Fedora on Python 3.7 with:
`.gnu.debuglto_.debug_macro' referenced in section
`.gnu.debuglto_.debug_macro' of
util/scripting-engines/trace-event-python.o: defined in discarded
section
In Fedora, Python 3.7 added -flto to the list of --cflags and since it
was only applied to util/scripting-engines/trace-event-python.c and
scripts/python/Perf-Trace-Util/Context.c, linking failed.
It's not the first time the addition of flags has broken builds: commit c6707fdef7e2 ("perf tools: Fix up build in hardnened environments")
appears to have fixed a similar problem. "python-config --includes"
provides the proper -I flags and doesn't introduce additional CFLAGS.
Signed-off-by: Jeremy Cline <jcline@redhat.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lkml.kernel.org/r/20180710154612.6285-1-jcline@redhat.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The original complaint was the lsscsi -t showed the same SAS address of the
two enclosures (SEP devices). In fact the SAS address was being set to the
Enclosure Logical Identifier (ELI).
Reviewed-by: Scott Teel <scott.teel@microsemi.com> Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com> Signed-off-by: Don Brace <don.brace@microsemi.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Calling bnxt_set_max_func_irqs() to modify the max IRQ count requested or
freed by the RDMA driver is flawed. The max IRQ count is checked when
re-initializing the IRQ vectors and this can happen multiple times
during ifup or ethtool -L. If the max IRQ is reduced and the RDMA
driver is operational, we may not initailize IRQs correctly. This
problem shows up on VFs with very small number of MSIX.
There is no other logic that relies on the IRQ count excluding the ones
used by RDMA. So we fix it by just removing the call to subtract or
add the IRQs used by RDMA.
Fixes: a588e4580a7e ("bnxt_en: Add interface to support RDMA driver.") Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In case of HSDK we have intermediate INTC in for of DW APB GPIO controller
which is used as a de-bounce logic for interrupt wires that come from
outside the board.
We cannot use existing "irq-dw-apb-ictl" driver here because all input
lines are routed to corresponding output lines but not muxed into one
line (this is configured in RTL and we cannot change this in software).
But even if we add such a feature to "irq-dw-apb-ictl" driver that won't
benefit us as higher-level INTC (in case of HSDK it is IDU) anyways has
per-input control so adding fully-controller intermediate INTC will only
bring some overhead on interrupt processing but no other benefits.
Thus we just do one-time configuration of DW APB GPIO controller and
forget about it.
Based on implementation available on arch/arc/plat-axs10x/axs10x.c file.
Dmitry Osipenko [Sat, 19 May 2018 01:07:10 +0000 (04:07 +0300)]
gpu: host1x: Skip IOMMU initialization if firewall is enabled
BugLink: https://bugs.launchpad.net/bugs/1835845
Host1x's CDMA can't access the command buffers if IOMMU and Host1x
firewall are enabled in the kernels config because firewall doesn't map
the copied buffer into IOVA space. Fix this by skipping IOMMU
initialization if firewall is enabled as firewall merges sparse cmdbufs
into a single contiguous buffer and hence IOMMU isn't needed in this case.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
(backported from commit 4466b1f0e022f94a026bd700fee34bff15cdc4ef) Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Setting the low threshold to 0 has no effect on frags allocation,
we need to clear high_thresh instead.
The code was pre-existent to commit 648700f76b03 ("inet: frags:
use rhashtables for reassembly units"), but before the above,
such assignment had a different role: prevent concurrent eviction
from the worker and the netns cleanup helper.
Fixes: 648700f76b03 ("inet: frags: use rhashtables for reassembly units") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Multiple BPF helpers in use by sk_skb programs calculate the max
skb length using the __bpf_skb_max_len function. However, this
calculates the max length using the skb->dev pointer which can be
NULL when an sk_skb program is paired with an sk_msg program.
To force this a sk_msg program needs to redirect into the ingress
path of a sock with an attach sk_skb program. Then the the sk_skb
program would need to call one of the helpers that adjust the skb
size.
To fix the null ptr dereference use SKB_MAX_ALLOC size if no dev
is available.
t4_get_flash_params() fails in a fatal fashion if the FLASH part isn't
one of the recognized parts. But this leads to desperate efforts to update
drivers when various FLASH parts which we are using suddenly become
unavailable and we need to substitute new FLASH parts. This has lead to
more than one Customer Field Emergency when a Customer has an old driver
and suddenly can't use newly shipped adapters.
This commit fixes this by simply assuming that the FLASH part is 4MB in
size if it can't be identified. Note that all Chelsio adapters will have
flash parts which are at least 4MB in size.
Signed-off-by: Casey Leedom <leedom@chelsio.com> Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
All the control messages broadcast to remote routers are using
QRTR_NODE_BCAST instead of using local router NODE ID which cause
the packets to be dropped on remote router due to invalid NODE ID.
Signed-off-by: Arun Kumar Neelakantam <aneela@codeaurora.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This file has never existed in the upstream kernel, but it's guarded by
an #ifdef that's also never existed in the upstream kernel. As a part
of our interrupt controller refactoring this header is no longer
necessary, but this reference managed to sneak in anyway.
I noticed that cgroup task groups constantly get throttled even
if they have low CPU usage, this causes some jitters on the response
time to some of our business containers when enabling CPU quotas.
cat cpu.stat | grep nr_throttled # nr_throttled will increase steadily
After some analysis, we found that cfs_rq::runtime_remaining will
be cleared by expire_cfs_rq_runtime() due to two equal but stale
"cfs_{b|q}->runtime_expires" after period timer is re-armed.
The current condition to judge clock drift in expire_cfs_rq_runtime()
is wrong, the two runtime_expires are actually the same when clock
drift happens, so this condtion can never hit. The orginal design was
correctly done by this commit:
... but was changed to be the current implementation due to its locking bug.
This patch introduces another way, it adds a new field in both structures
cfs_rq and cfs_bandwidth to record the expiration update sequence, and
uses them to figure out if clock drift happens (true if they are equal).
Signed-off-by: Xunlei Pang <xlpang@linux.alibaba.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Ben Segall <bsegall@google.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Fixes: 51f2176d74ac ("sched/fair: Fix unlocked reads of some cfs_b->quota/period") Link: http://lkml.kernel.org/r/20180620101834.24455-1-xlpang@linux.alibaba.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
commit e830baa9c3f0 ("qeth: restore device features after recovery") and
commit ce3443564145 ("s390/qeth: rely on kernel for feature recovery")
made sure that the HW functions for device features get re-programmed
after recovery.
But we missed that the same handling is also required when a card is
first set offline (destroying all HW context), and then online again.
Fix this by moving the re-enable action out of the recovery-only path.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
perf_event__process_feature() accesses feat_ops[HEADER_LAST_FEATURE]
which is not defined and thus perf is crashing. HEADER_LAST_FEATURE is
used as an end marker for the perf report but it's unused for perf
script/annotate. Ignore HEADER_LAST_FEATURE for perf script/annotate,
just like it is done in 'perf report'.
Before:
# perf record -o - ls | perf script
<SNIP 'ls' output>
Segmentation fault (core dumped)
#
After:
# perf record -o - ls | perf script
<SNIP 'ls' output>
Segmentation fault (core dumped)
ls 7031 4392.099856: 250000 cpu-clock:uhH: 7f5e0ce7cd60
ls 7031 4392.100355: 250000 cpu-clock:uhH: 7f5e0c706ef7
#
Signed-off-by: Ravi Bangoria <ravi.bangoria@linux.ibm.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: David Ahern <dsahern@gmail.com> Cc: David Carrillo-Cisneros <davidcc@google.com> Cc: Jin Yao <yao.jin@linux.intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Namhyung Kim <namhyung@kernel.org> Fixes: 57b5de463925 ("perf report: Support forced leader feature in pipe mode") Link: http://lkml.kernel.org/r/20180625124220.6434-4-ravi.bangoria@linux.ibm.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Adding the struct parse_events_error argument to parse_events call. Also
adding parse_events_print_error to get more details on the parsing
failures, like:
Use named initializers in the struct parse_events_error variable to
avoid breaking the build on centos5, 6 and others with a similar gcc:
cc1: warnings being treated as errors
tests/parse-events.c: In function 'test_event':
tests/parse-events.c:1696: error: missing initializer
tests/parse-events.c:1696: error: (near initialization for 'err.str')
Reported-by: Kim Phillips <kim.phillips@arm.com> Signed-off-by: Jiri Olsa <jolsa@kernel.org> Tested-by: Kim Phillips <kim.phillips@arm.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: David Ahern <dsahern@gmail.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Hendrik Brueckner <brueckner@linux.vnet.ibm.com> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Richter <tmricht@linux.ibm.com> Link: http://lkml.kernel.org/r/20180611093422.1005-1-jolsa@kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Stopping offload completely if replace of program failed dates
back to days of transparent offload. Back then we wanted to
silently fall back to the in-driver processing. Today we mark
programs for offload when they are loaded into the kernel, so
the transparent offload is no longer a reality.
Flags check in the driver will only allow replace of a driver
program with another driver program or an offload program with
another offload program.
When driver program is replaced stopping offload is a no-op,
because driver program isn't offloaded. When replacing
offloaded program if the offload fails the entire operation
will fail all the way back to user space and we should continue
using the old program. IOW when replacing a driver program
stopping offload is unnecessary and when replacing offloaded
program - it's a bug, old program should continue to run.
In practice this bug would mean that if offload operation was to
fail (either due to FW communication error, kernel OOM or new
program being offloaded but for a different netdev) driver
would continue reporting that previous XDP program is offloaded
but in fact no program will be loaded in hardware. The failure
is fairly unlikely (found by inspection, when working on the code)
but it's unpleasant.
Backport note: even though the bug was introduced in commit cafa92ac2553 ("nfp: bpf: add support for XDP_FLAGS_HW_MODE"),
this fix depends on commit 441a33031fe5 ("net: xdp: don't allow
device-bound programs in driver mode"), so this fix is sufficient
only in v4.15 or newer. Kernels v4.13.x and v4.14.x do need to
stop offload if it was transparent/opportunistic, i.e. if
XDP_FLAGS_HW_MODE was not set on running program.
Fixes: cafa92ac2553 ("nfp: bpf: add support for XDP_FLAGS_HW_MODE") Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com> Acked-by: Song Liu <songliubraving@fb.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
batman-adv is creating special debugfs directories in the init
net_namespace for each created soft-interface (batadv net_device). But it
is possible to rename a net_device to a completely different name then the
original one.
It can therefore happen that a user registers a new batadv net_device with
the name "bat0". batman-adv is then also adding a new directory under
$debugfs/batman-adv/ with the name "wlan0".
The user then decides to rename this device to "bat1" and registers a
different batadv device with the name "bat0". batman-adv will then try to
create a directory with the name "bat0" under $debugfs/batman-adv/ again.
But there already exists one with this name under this path and thus this
fails. batman-adv will detect a problem and rollback the registering of
this device.
batman-adv must therefore take care of renaming the debugfs directories for
soft-interfaces whenever it detects such a net_device rename.
batman-adv is creating special debugfs directories in the init
net_namespace for each valid hard-interface (net_device). But it is
possible to rename a net_device to a completely different name then the
original one.
It can therefore happen that a user registers a new net_device which gets
the name "wlan0" assigned by default. batman-adv is also adding a new
directory under $debugfs/batman-adv/ with the name "wlan0".
The user then decides to rename this device to "wl_pri" and registers a
different device. The kernel may now decide to use the name "wlan0" again
for this new device. batman-adv will detect it as a valid net_device and
tries to create a directory with the name "wlan0" under
$debugfs/batman-adv/. But there already exists one with this name under
this path and thus this fails. batman-adv will detect a problem and
rollback the registering of this device.
batman-adv must therefore take care of renaming the debugfs directories
for hard-interfaces whenever it detects such a net_device rename.
Fixes: 5bc7c1eb44f2 ("batman-adv: add debugfs structure for information per interface") Reported-by: John Soros <sorosj@gmail.com> Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
We had commit 06e226c7fb23 ("clk: sunxi-ng: Move all clock types to a
library") and commit 799c43415442 ("kbuild: thin archives make default
for all archs") in the same development cycle, from different trees.
With migration to the thin archive, the entire drivers/clk/sunxi-ng/lib.a
is linked to the vmlinux. This does not break build, but we do not get
any size saving.
However, we do not need to go back to the individual Kconfig options.
The default configuration pulls in all (or most) of the CCU parts anyway.
Also, once we enable CONFIG_LD_DEAD_CODE_DATA_ELIMINATION, we can simply
list all files with obj-y, and the linker will drop all unused functions
by itself.
After the long discussion [1], people there agreed to fix this, but
nobody sent a patch after all. I am doing it now.
I lifted up CONFIG_SUNXI_CCU to drivers/clk/Makefile because everything
in drivers/clk/sunxi-ng/ depends on SUNXI_CCU.
Finally, the request_queue is quiesced state when wait freeze,
we will get io hang here. To fix it, move the nvme_kill_queues
from nvme_remove_dead_ctrl_work to nvme_remove_dead_ctrl.
Suggested-by: Keith Busch <keith.busch@linux.intel.com> Signed-off-by: Jianchao Wang <jianchao.w.wang@oracle.com> Reviewed-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The race is between completing the request at error recovery work and
rdma completions. If we cancel the request before getting the good
rdma completion we get a NULL deref of the request MR at
nvme_rdma_process_nvme_rsp().
When Canceling the request we return its mr to the mr pool (set mr to
NULL) and also unmap its data. Canceling the requests while the rdma
queues are active is not safe. Because rdma queues are active and we
get good rdma completions that can use the mr pointer which may be NULL.
Completing the request too soon may lead also to performing DMA to/from
user buffers which might have been already unmapped.
The commit fixes the race by draining the QP before starting the abort
commands mechanism.
Signed-off-by: Israel Rukshin <israelr@mellanox.com> Reviewed-by: Max Gurtovoy <maxg@mellanox.com> Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Failures after nvme_init_ctrl will defer resource cleanups to .free_ctrl
when the reference is released, hence we should not free the controller
queues for these failures.
Fix that by moving controller queues allocation before controller
initialization and correctly freeing them for failures before
initialization and skip them for failures after initialization.
Commit 0198d7bb8a0c ("ASoC: omap-mcbsp: Convert to use the sdma-pcm
instead of omap-pcm") resulted in broken audio playback on OMAP1510
(discovered on Amstrad Delta).
When running on OMAP1510, omap-pcm used to obtain DMA offset from
snd_dmaengine_pcm_pointer_no_residue() based on DMA interrupt triggered
software calculations instead of snd_dmaengine_pcm_pointer() which
depended on residue value calculated from omap_dma_get_src_pos().
Similar code path is still available in now used
sound/soc/soc-generic-dmaengine-pcm.c but it is not triggered.
It was verified already before that omap_get_dma_src_pos() from
arch/arm/plat-omap/dma.c didn't work correctly for OMAP1510 - see
commit 1bdd7419910c ("ASoC: OMAP: fix OMAP1510 broken PCM pointer
callback") for details. Apparently the same applies to its successor,
omap_dma_get_src_pos() from drivers/dma/ti/omap-dma.c.
On the other hand, snd_dmaengine_pcm_pointer_no_residue() is described
as depreciated and discouraged for use in new drivers because of its
unreliable accuracy. However, it seems the only working option for
OPAM1510 now, as long as a software calculated residue is not
implemented as OMAP1510 fallback in omap-dma.
Using snd_dmaengine_pcm_pointer_no_residue() code path instead of
snd_dmaengine_pcm_pointer() in sound/soc/soc-generic-dmaengine-pcm.c
can be triggered in two ways:
- by passing pcm->flags |= SND_DMAENGINE_PCM_FLAG_NO_RESIDUE from
sound/soc/omap/sdma-pcm.c,
- by passing dma_caps.residue_granularity =
DMA_RESIDUE_GRANULARITY_DESCRIPTOR from DMA engine.
Let's do the latter.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com> Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
One needs to ensure that the crtcs are shutdown so that the
drm_crtc_state->connector_mask reflects that no connectors
are currently active. Further, it reduces the reference
count for each connector. This ensures that the connectors
and encoders can be cleanly removed either when _unbind
is called for the corresponding drivers or by
drm_mode_config_cleanup().
We need drm_atomic_helper_shutdown() to be called before
component_unbind_all() otherwise the connectors attached to the
component device will have the wrong reference count value and will not
be cleanly removed.
Calling fan related SMM functions implemented by Dell BIOS firmware on Dell
XPS13 9333 freeze kernel for about 500ms. Until Dell fixes it we need to
disable fan support for Dell XPS13 9333.
Via "force" module param fan support can be enabled.
Compared to other clients the Linux smb3 client ramps up
credits very slowly, taking more than 128 operations before a
maximum size write could be sent (since the number of credits
requested is only 2 per small operation, causing the credit
limit to grow very slowly).
This lack of credits initially would impact large i/o performance,
when large i/o is tried early before enough credits are built up.
Signed-off-by: Steve French <sfrench@gmail.com> Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Some RoCE specific code in qedr_modify_qp was run over an iWARP device
when running perftest benchmarks without the -R option.
The commit 3e44e0ee0893 ("IB/providers: Avoid null netdev check for RoCE")
exposed this. Dropping the check for NULL pointer on ndev in
qedr_modify_qp lead to a null pointer dereference when running over
iWARP. Before the code would identify ndev as being NULL and return an
error.
In rxe_send, when network_type is not RDMA_NETWORK_IPV4 or
RDMA_NETWORK_IPV6, skb is freed and -EINVAL is returned.
Then rxe_xmit_packet will return -EINVAL, too. In rxe_requester,
this skb is double freed.
In rxe_requester, kfree_skb is needed only after fill_packet fails.
So kfree_skb is moved from label err to test fill_packet.
Fixes: 5793b4652155 ("IB/rxe: remove unnecessary skb_clone in xmit") Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com> Reviewed-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
projects / mirror_ubuntu-bionic-kernel.git / log