When CONFIG_MIGRATE_VMA_HELPER is enabled, migrate_vma() calls
migrate_vma_collect() which initializes a struct mm_walk but didn't
initialize mm_walk.pud_entry. (Found by code inspection) Use a C
structure initialization to make sure it is set to NULL.
Link: http://lkml.kernel.org/r/20190719233225.12243-1-rcampbell@nvidia.com Fixes: 8763cb45ab967 ("mm/migrate: new memory migration helper for use with device memory") Signed-off-by: Ralph Campbell <rcampbell@nvidia.com> Reviewed-by: John Hubbard <jhubbard@nvidia.com> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: "Jérôme Glisse" <jglisse@redhat.com> Cc: Mel Gorman <mgorman@techsingularity.net> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Driver was not disabling TXRDY interrupt after last TX byte.
This caused interrupt storm until transfer timeouts for slow
or broken device on the bus. The patch fixes the interrupt storm
on my SAMA5D2-based board.
Cc: stable@vger.kernel.org # 5.2.x
[v5.2 introduced file split; the patch should apply to i2c-at91.c before the split] Fixes: fac368a04048 ("i2c: at91: add new driver") Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com> Tested-by: Raag Jadav <raagjadav@gmail.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If gpiolib is disabled, we use the inline stubs from gpio/consumer.h
instead of regular definitions of GPIO API. The stubs for 'optional'
variants of gpiod_get routines return NULL in this case as if the
relevant GPIO wasn't found. This is correct so far.
Calling other (non-gpio_get) stubs from this header triggers a warning
because the GPIO descriptor couldn't have been requested. The warning
however is unconditional (WARN_ON(1)) and is emitted even if the passed
descriptor pointer is NULL.
We don't want to force the users of 'optional' gpio_get to check the
returned pointer before calling e.g. gpiod_set_value() so let's only
WARN on non-NULL descriptors.
Since the cached32_node is allowed to be advanced above dma_32bit_pfn
(to provide a shortcut into the limited range), we need to be careful to
remove the to be freed node if it is the cached32_node.
[ 48.477773] BUG: KASAN: use-after-free in __cached_rbnode_delete_update+0x68/0x110
[ 48.477812] Read of size 8 at addr ffff88870fc19020 by task kworker/u8:1/37
[ 48.477843]
[ 48.477879] CPU: 1 PID: 37 Comm: kworker/u8:1 Tainted: G U 5.2.0+ #735
[ 48.477915] Hardware name: Intel Corporation NUC7i5BNK/NUC7i5BNB, BIOS BNKBL357.86A.0052.2017.0918.1346 09/18/2017
[ 48.478047] Workqueue: i915 __i915_gem_free_work [i915]
[ 48.478075] Call Trace:
[ 48.478111] dump_stack+0x5b/0x90
[ 48.478137] print_address_description+0x67/0x237
[ 48.478178] ? __cached_rbnode_delete_update+0x68/0x110
[ 48.478212] __kasan_report.cold.3+0x1c/0x38
[ 48.478240] ? __cached_rbnode_delete_update+0x68/0x110
[ 48.478280] ? __cached_rbnode_delete_update+0x68/0x110
[ 48.478308] __cached_rbnode_delete_update+0x68/0x110
[ 48.478344] private_free_iova+0x2b/0x60
[ 48.478378] iova_magazine_free_pfns+0x46/0xa0
[ 48.478403] free_iova_fast+0x277/0x340
[ 48.478443] fq_ring_free+0x15a/0x1a0
[ 48.478473] queue_iova+0x19c/0x1f0
[ 48.478597] cleanup_page_dma.isra.64+0x62/0xb0 [i915]
[ 48.478712] __gen8_ppgtt_cleanup+0x63/0x80 [i915]
[ 48.478826] __gen8_ppgtt_cleanup+0x42/0x80 [i915]
[ 48.478940] __gen8_ppgtt_clear+0x433/0x4b0 [i915]
[ 48.479053] __gen8_ppgtt_clear+0x462/0x4b0 [i915]
[ 48.479081] ? __sg_free_table+0x9e/0xf0
[ 48.479116] ? kfree+0x7f/0x150
[ 48.479234] i915_vma_unbind+0x1e2/0x240 [i915]
[ 48.479352] i915_vma_destroy+0x3a/0x280 [i915]
[ 48.479465] __i915_gem_free_objects+0xf0/0x2d0 [i915]
[ 48.479579] __i915_gem_free_work+0x41/0xa0 [i915]
[ 48.479607] process_one_work+0x495/0x710
[ 48.479642] worker_thread+0x4c7/0x6f0
[ 48.479687] ? process_one_work+0x710/0x710
[ 48.479724] kthread+0x1b2/0x1d0
[ 48.479774] ? kthread_create_worker_on_cpu+0xa0/0xa0
[ 48.479820] ret_from_fork+0x1f/0x30
[ 48.479864]
[ 48.479907] Allocated by task 631:
[ 48.479944] save_stack+0x19/0x80
[ 48.479994] __kasan_kmalloc.constprop.6+0xc1/0xd0
[ 48.480038] kmem_cache_alloc+0x91/0xf0
[ 48.480082] alloc_iova+0x2b/0x1e0
[ 48.480125] alloc_iova_fast+0x58/0x376
[ 48.480166] intel_alloc_iova+0x90/0xc0
[ 48.480214] intel_map_sg+0xde/0x1f0
[ 48.480343] i915_gem_gtt_prepare_pages+0xb8/0x170 [i915]
[ 48.480465] huge_get_pages+0x232/0x2b0 [i915]
[ 48.480590] ____i915_gem_object_get_pages+0x40/0xb0 [i915]
[ 48.480712] __i915_gem_object_get_pages+0x90/0xa0 [i915]
[ 48.480834] i915_gem_object_prepare_write+0x2d6/0x330 [i915]
[ 48.480955] create_test_object.isra.54+0x1a9/0x3e0 [i915]
[ 48.481075] igt_shared_ctx_exec+0x365/0x3c0 [i915]
[ 48.481210] __i915_subtests.cold.4+0x30/0x92 [i915]
[ 48.481341] __run_selftests.cold.3+0xa9/0x119 [i915]
[ 48.481466] i915_live_selftests+0x3c/0x70 [i915]
[ 48.481583] i915_pci_probe+0xe7/0x220 [i915]
[ 48.481620] pci_device_probe+0xe0/0x180
[ 48.481665] really_probe+0x163/0x4e0
[ 48.481710] device_driver_attach+0x85/0x90
[ 48.481750] __driver_attach+0xa5/0x180
[ 48.481796] bus_for_each_dev+0xda/0x130
[ 48.481831] bus_add_driver+0x205/0x2e0
[ 48.481882] driver_register+0xca/0x140
[ 48.481927] do_one_initcall+0x6c/0x1af
[ 48.481970] do_init_module+0x106/0x350
[ 48.482010] load_module+0x3d2c/0x3ea0
[ 48.482058] __do_sys_finit_module+0x110/0x180
[ 48.482102] do_syscall_64+0x62/0x1f0
[ 48.482147] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 48.482190]
[ 48.482224] Freed by task 37:
[ 48.482273] save_stack+0x19/0x80
[ 48.482318] __kasan_slab_free+0x12e/0x180
[ 48.482363] kmem_cache_free+0x70/0x140
[ 48.482406] __free_iova+0x1d/0x30
[ 48.482445] fq_ring_free+0x15a/0x1a0
[ 48.482490] queue_iova+0x19c/0x1f0
[ 48.482624] cleanup_page_dma.isra.64+0x62/0xb0 [i915]
[ 48.482749] __gen8_ppgtt_cleanup+0x63/0x80 [i915]
[ 48.482873] __gen8_ppgtt_cleanup+0x42/0x80 [i915]
[ 48.482999] __gen8_ppgtt_clear+0x433/0x4b0 [i915]
[ 48.483123] __gen8_ppgtt_clear+0x462/0x4b0 [i915]
[ 48.483250] i915_vma_unbind+0x1e2/0x240 [i915]
[ 48.483378] i915_vma_destroy+0x3a/0x280 [i915]
[ 48.483500] __i915_gem_free_objects+0xf0/0x2d0 [i915]
[ 48.483622] __i915_gem_free_work+0x41/0xa0 [i915]
[ 48.483659] process_one_work+0x495/0x710
[ 48.483704] worker_thread+0x4c7/0x6f0
[ 48.483748] kthread+0x1b2/0x1d0
[ 48.483787] ret_from_fork+0x1f/0x30
[ 48.483831]
[ 48.483868] The buggy address belongs to the object at ffff88870fc19000
[ 48.483868] which belongs to the cache iommu_iova of size 40
[ 48.483920] The buggy address is located 32 bytes inside of
[ 48.483920] 40-byte region [ffff88870fc19000, ffff88870fc19028)
[ 48.483964] The buggy address belongs to the page:
[ 48.484006] page:ffffea001c3f0600 refcount:1 mapcount:0 mapping:ffff8888181a91c0 index:0x0 compound_mapcount: 0
[ 48.484045] flags: 0x8000000000010200(slab|head)
[ 48.484096] raw: 8000000000010200ffffea001c421a08ffffea001c447e88ffff8888181a91c0
[ 48.484141] raw: 0000000000000000000000000012001200000001ffffffff0000000000000000
[ 48.484188] page dumped because: kasan: bad access detected
[ 48.484230]
[ 48.484265] Memory state around the buggy address:
[ 48.484314] ffff88870fc18f00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 48.484361] ffff88870fc18f80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 48.484406] >ffff88870fc19000: fb fb fb fb fb fc fc fc fc fc fc fc fc fc fc fc
[ 48.484451] ^
[ 48.484494] ffff88870fc19080: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 48.484530] ffff88870fc19100: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=108602 Fixes: e60aa7b53845 ("iommu/iova: Extend rbtree node caching") Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Robin Murphy <robin.murphy@arm.com> Cc: Joerg Roedel <jroedel@suse.de> Cc: Joerg Roedel <joro@8bytes.org> Cc: <stable@vger.kernel.org> # v4.15+ Reviewed-by: Robin Murphy <robin.murphy@arm.com> Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
It turned out that the recent Intel HD-audio controller chips show a
significant stall during the system PM resume intermittently. It
doesn't happen so often and usually it may read back successfully
after one or more seconds, but in some rare worst cases the driver
went into fallback mode.
After trial-and-error, we found out that the communication stall seems
covered by issuing the sync after each verb write, as already done for
AMD and other chipsets. So this patch enables the write-sync flag for
the recent Intel chips, Skylake and onward, as a workaround.
Also, since Broxton and co have the very same driver flags as Skylake,
refer to the Skylake driver flags instead of defining the same
contents again for simplification.
This patch adds support for the Armadeus ST0700 Adapt. It comes with a
Santek ST0700I5Y-RBSLW 7.0" WVGA (800x480) TFT and an adapter board so
that it can be connected on the TFT header of Armadeus Dev boards.
Cc: stable@vger.kernel.org # v4.19 Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com> Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Link: https://patchwork.freedesktop.org/patch/msgid/20190507152713.27494-1-sebastien.szymanski@armadeus.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Check if in fail_io mode at start of dm_pool_metadata_set_needs_check().
Otherwise dm_pool_metadata_set_needs_check()'s superblock_lock() can
crash in dm_bm_write_lock() while accessing the block manager object
that was previously destroyed as part of a failed
dm_pool_abort_metadata() that ultimately set fail_io to begin with.
Also, update DMERR() message to more accurately describe
superblock_lock() failure.
The pstore_mkfile() function is passed a pointer to a struct
pstore_record. On success it consumes this 'record' pointer and
references it from the created inode.
On failure, however, it may or may not free the record. There are even
two different code paths which return -ENOMEM -- one of which does and
the other doesn't free the record.
Make the behaviour deterministic by never consuming and freeing the
record when returning failure, allowing the caller to do the cleanup
consistently.
Signed-off-by: Norbert Manthey <nmanthey@amazon.de> Link: https://lore.kernel.org/r/1562331960-26198-1-git-send-email-nmanthey@amazon.de Fixes: 83f70f0769ddd ("pstore: Do not duplicate record metadata") Fixes: 1dfff7dd67d1a ("pstore: Pass record contents instead of copying") Cc: stable@vger.kernel.org
[kees: also move "private" allocation location, rename inode cleanup label] Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Since resources can be removed, locking should ensure that the resource
is not removed while accessing it. However, find_next_iomem_res() does
not hold the lock while copying the data of the resource.
Keep holding the lock while the data is copied. While at it, change the
return value to a more informative value. It is disregarded by the
callers.
[akpm@linux-foundation.org: fix find_next_iomem_res() documentation] Link: http://lkml.kernel.org/r/20190613045903.4922-2-namit@vmware.com Fixes: ff3cc952d3f00 ("resource: Add remove_resource interface") Signed-off-by: Nadav Amit <namit@vmware.com> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Reviewed-by: Dan Williams <dan.j.williams@intel.com> Cc: Borislav Petkov <bp@suse.de> Cc: Toshi Kani <toshi.kani@hpe.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: Bjorn Helgaas <bhelgaas@google.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Previously find_next_iomem_res() used "*res" as both an input parameter for
the range to search and the type of resource to search for, and an output
parameter for the resource we found, which makes the interface confusing.
The current callers use find_next_iomem_res() incorrectly because they
allocate a single struct resource and use it for repeated calls to
find_next_iomem_res(). When find_next_iomem_res() returns a resource, it
overwrites the start, end, flags, and desc members of the struct. If we
call find_next_iomem_res() again, we must update or restore these fields.
The previous code restored res.start and res.end, but not res.flags or
res.desc.
Since the callers did not restore res.flags, if they searched for flags
IORESOURCE_MEM | IORESOURCE_BUSY and found a resource with flags
IORESOURCE_MEM | IORESOURCE_BUSY | IORESOURCE_SYSRAM, the next search would
incorrectly skip resources unless they were also marked as
IORESOURCE_SYSRAM.
Fix this by restructuring the interface so it takes explicit "start, end,
flags" parameters and uses "*res" only as an output parameter.
Based on a patch by Lianbo Jiang <lijiang@redhat.com>.
[ bp: While at it:
- make comments kernel-doc style.
-
Originally-by: http://lore.kernel.org/lkml/20180921073211.20097-2-lijiang@redhat.com Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Borislav Petkov <bp@suse.de> CC: Andrew Morton <akpm@linux-foundation.org> CC: Brijesh Singh <brijesh.singh@amd.com> CC: Dan Williams <dan.j.williams@intel.com> CC: H. Peter Anvin <hpa@zytor.com> CC: Lianbo Jiang <lijiang@redhat.com> CC: Takashi Iwai <tiwai@suse.de> CC: Thomas Gleixner <tglx@linutronix.de> CC: Tom Lendacky <thomas.lendacky@amd.com> CC: Vivek Goyal <vgoyal@redhat.com> CC: Yaowei Bai <baiyaowei@cmss.chinamobile.com> CC: bhe@redhat.com CC: dan.j.williams@intel.com CC: dyoung@redhat.com CC: kexec@lists.infradead.org CC: mingo@redhat.com CC: x86-ml <x86@kernel.org> Link: http://lkml.kernel.org/r/153805812916.1157.177580438135143788.stgit@bhelgaas-glaptop.roam.corp.google.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
find_next_iomem_res() finds an iomem resource that covers part of a range
described by "start, end". All callers expect that range to be inclusive,
i.e., both start and end are included, but find_next_iomem_res() doesn't
handle the end address correctly.
If it finds an iomem resource that contains exactly the end address, it
skips it, e.g., if "start, end" is [0x0-0x10000] and there happens to be an
iomem resource [mem 0x10000-0x10000] (the single byte at 0x10000), we skip
it:
find_next_iomem_res(...)
{
start = 0x0;
end = 0x10000;
for (p = next_resource(...)) {
# p->start = 0x10000;
# p->end = 0x10000;
# we *should* return this resource, but this condition is false:
if ((p->end >= start) && (p->start < end))
break;
Adjust find_next_iomem_res() so it allows a resource that includes the
single byte at the end of the range. This is a corner case that we
probably don't see in practice.
Fixes: 58c1b5b07907 ("[PATCH] memory hotadd fixes: find_next_system_ram catch range fix") Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Borislav Petkov <bp@suse.de> CC: Andrew Morton <akpm@linux-foundation.org> CC: Brijesh Singh <brijesh.singh@amd.com> CC: Dan Williams <dan.j.williams@intel.com> CC: H. Peter Anvin <hpa@zytor.com> CC: Lianbo Jiang <lijiang@redhat.com> CC: Takashi Iwai <tiwai@suse.de> CC: Thomas Gleixner <tglx@linutronix.de> CC: Tom Lendacky <thomas.lendacky@amd.com> CC: Vivek Goyal <vgoyal@redhat.com> CC: Yaowei Bai <baiyaowei@cmss.chinamobile.com> CC: bhe@redhat.com CC: dan.j.williams@intel.com CC: dyoung@redhat.com CC: kexec@lists.infradead.org CC: mingo@redhat.com CC: x86-ml <x86@kernel.org> Link: http://lkml.kernel.org/r/153805812254.1157.16736368485811773752.stgit@bhelgaas-glaptop.roam.corp.google.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
A previous fix to prevent KVM from consuming stale VMCS state after a
failed VM-Entry inadvertantly blocked KVM's handling of machine checks
that occur during VM-Entry.
Per Intel's SDM, a #MC during VM-Entry is handled in one of three ways,
depending on when the #MC is recognoized. As it pertains to this bug
fix, the third case explicitly states EXIT_REASON_MCE_DURING_VMENTRY
is handled like any other VM-Exit during VM-Entry, i.e. sets bit 31 to
indicate the VM-Entry failed.
If a machine-check event occurs during a VM entry, one of the following occurs:
- The machine-check event is handled as if it occurred before the VM entry:
...
- The machine-check event is handled after VM entry completes:
...
- A VM-entry failure occurs as described in Section 26.7. The basic
exit reason is 41, for "VM-entry failure due to machine-check event".
Explicitly handle EXIT_REASON_MCE_DURING_VMENTRY as a one-off case in
vmx_vcpu_run() instead of binning it into vmx_complete_atomic_exit().
Doing so allows vmx_vcpu_run() to handle VMX_EXIT_REASONS_FAILED_VMENTRY
in a sane fashion and also simplifies vmx_complete_atomic_exit() since
VMCS.VM_EXIT_INTR_INFO is guaranteed to be fresh.
Fixes: b060ca3b2e9e7 ("kvm: vmx: Handle VMLAUNCH/VMRESUME failure properly") Cc: stable@vger.kernel.org Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com> Reviewed-by: Jim Mattson <jmattson@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
remove_session_caps() relies on __wait_on_freeing_inode(), to wait for
freeing inode to remove its caps. But VFS wakes freeing inode waiters
before calling destroy_inode().
When tracing instances where we open and close WKA ports, we also pass the
request-ID of the respective FSF command.
But after successfully sending the FSF command we must not use the
request-object anymore, as this might result in an use-after-free (see
"zfcp: fix request object use-after-free in send path causing seqno
errors" ).
To fix this add a new variable that caches the request-ID before sending
the request. This won't change during the hand-off to the FCP channel,
and so it's safe to trace this cached request-ID later, instead of using
the request object.
Signed-off-by: Benjamin Block <bblock@linux.ibm.com> Fixes: d27a7cb91960 ("zfcp: trace on request for open and close of WKA port") Cc: <stable@vger.kernel.org> #2.6.38+ Reviewed-by: Steffen Maier <maier@linux.ibm.com> Reviewed-by: Jens Remus <jremus@linux.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
For the error path in wilc_wlan_initialize(), the resources are not
cleanup in the correct order. Reverted the previous changes and use the
correct order to free during error condition.
Each function that manipulates the aa_ext struct should reset it's "pos"
member on failure. This ensures that, on failure, no changes are made to
the state of the aa_ext struct.
There are paths were elements are optional and the error path is
used to indicate the optional element is not present. This means
instead of just aborting on error the unpack stream can become
unsynchronized on optional elements, if using one of the affected
functions.
Cc: stable@vger.kernel.org Fixes: 736ec752d95e ("AppArmor: policy routines for loading and unpacking policy") Signed-off-by: Mike Salvatore <mike.salvatore@canonical.com> Signed-off-by: John Johansen <john.johansen@canonical.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Heavy contention of the sde flushlist_lock can cause hard lockups at
extreme scale when the flushing logic is under stress.
Mitigate by replacing the item at a time copy to the local list with
an O(1) list_splice_init() and using the high priority work queue to
do the flushes.
Fixes: 7724105686e7 ("IB/hfi1: add driver files") Cc: <stable@vger.kernel.org> Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If a task is removing the block group that currently has the highest start
offset amongst all existing block groups, there is a short time window
where it races with a concurrent block group allocation, resulting in a
transaction abort with an error code of EEXIST.
The following diagram explains the race in detail:
Task A Task B
btrfs_remove_block_group(bg offset X)
remove_extent_mapping(em offset X)
-> removes extent map X from the
tree of extent maps
(fs_info->mapping_tree), so the
next call to find_next_chunk()
will return offset X
btrfs_alloc_chunk()
find_next_chunk()
--> returns offset X
__btrfs_alloc_chunk(offset X)
btrfs_make_block_group()
btrfs_create_block_group_cache()
--> creates btrfs_block_group_cache
object with a key corresponding
to the block group item in the
extent, the key is:
(offset X, BTRFS_BLOCK_GROUP_ITEM_KEY, 1G)
--> adds the btrfs_block_group_cache object
to the list new_bgs of the transaction
handle
btrfs_end_transaction(trans handle)
__btrfs_end_transaction()
btrfs_create_pending_block_groups()
--> sees the new btrfs_block_group_cache
in the new_bgs list of the transaction
handle
--> its call to btrfs_insert_item() fails
with -EEXIST when attempting to insert
the block group item key
(offset X, BTRFS_BLOCK_GROUP_ITEM_KEY, 1G)
because task A has not removed that key yet
--> aborts the running transaction with
error -EEXIST
btrfs_del_item()
-> removes the block group's key from
the extent tree, key is
(offset X, BTRFS_BLOCK_GROUP_ITEM_KEY, 1G)
Fix this by calling remove_extent_mapping(), at btrfs_remove_block_group(),
only at the very end, after removing the block group item key from the
extent tree (and removing the free space tree entry if we are using the
free space tree feature).
Fixes: 04216820fe83d5 ("Btrfs: fix race between fs trimming and block group remove/allocation") CC: stable@vger.kernel.org # 4.4+ Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
[What]
readptr read always returns zero, since most likely
these blocks are either power or clock gated.
[How]
fetch rptr after amdgpu_ring_alloc() which informs
the power management code that the block is about to be
used and hence the gating is turned off.
Signed-off-by: Louis Li <Ching-shih.Li@amd.com> Signed-off-by: Shirish S <shirish.s@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
[What]
vce ring test fails consistently during resume in s3 cycle, due to
mismatch read & write pointers.
On debug/analysis its found that rptr to be compared is not being
correctly updated/read, which leads to this failure.
Below is the failure signature:
[drm:amdgpu_vce_ring_test_ring] *ERROR* amdgpu: ring 12 test failed
[drm:amdgpu_device_ip_resume_phase2] *ERROR* resume of IP block <vce_v3_0> failed -110
[drm:amdgpu_device_resume] *ERROR* amdgpu_device_ip_resume failed (-110).
[How]
fetch rptr appropriately, meaning move its read location further down
in the code flow.
With this patch applied the s3 failure is no more seen for >5k s3 cycles,
which otherwise is pretty consistent.
V2: remove reduntant fetch of rptr
Signed-off-by: Louis Li <Ching-shih.Li@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When assigning kvm irqfd we didn't check the irqchip mode but we allow
KVM_IRQFD to succeed with all the irqchip modes. However it does not
make much sense to create irqfd even without the kernel chips. Let's
provide a arch-dependent helper to check whether a specific irqfd is
allowed by the arch. At least for x86, it should make sense to check:
- when irqchip mode is NONE, all irqfds should be disallowed, and,
- when irqchip mode is SPLIT, irqfds that are with resamplefd should
be disallowed.
For either of the case, previously we'll silently ignore the irq or
the irq ack event if the irqchip mode is incorrect. However that can
cause misterious guest behaviors and it can be hard to triage. Let's
fail KVM_IRQFD even earlier to detect these incorrect configurations.
CC: Paolo Bonzini <pbonzini@redhat.com> CC: Radim Krčmář <rkrcmar@redhat.com> CC: Alex Williamson <alex.williamson@redhat.com> CC: Eduardo Habkost <ehabkost@redhat.com> Signed-off-by: Peter Xu <peterx@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The information about tag size should not be printed without debug info
set. Also print device major:minor in the error message to identify the
device instance.
Also use rate limiting and debug level for info about used crypto API
implementaton. This is important because during online reencryption
the existing message saturates syslog (because we are moving hotzone
across the whole device).
Cc: stable@vger.kernel.org Signed-off-by: Milan Broz <gmazyland@gmail.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Once blk_cleanup_queue() returns, tags shouldn't be used any more,
because blk_mq_free_tag_set() may be called. Commit 45a9c9d909b2
("blk-mq: Fix a use-after-free") fixes this issue exactly.
However, that commit introduces another issue. Before 45a9c9d909b2,
we are allowed to run queue during cleaning up queue if the queue's
kobj refcount is held. After that commit, queue can't be run during
queue cleaning up, otherwise oops can be triggered easily because
some fields of hctx are freed by blk_mq_free_queue() in blk_cleanup_queue().
We have invented ways for addressing this kind of issue before, such as:
8dc765d438f1 ("SCSI: fix queue cleanup race before queue initialization is done") c2856ae2f315 ("blk-mq: quiesce queue before freeing queue")
But still can't cover all cases, recently James reports another such
kind of issue:
This issue can be quite hard to address by previous way, given
scsi_run_queue() may run requeues for other LUNs.
Fixes the above issue by freeing hctx's resources in its release handler, and this
way is safe becasue tags isn't needed for freeing such hctx resource.
This approach follows typical design pattern wrt. kobject's release handler.
Cc: Dongli Zhang <dongli.zhang@oracle.com> Cc: James Smart <james.smart@broadcom.com> Cc: Bart Van Assche <bart.vanassche@wdc.com> Cc: linux-scsi@vger.kernel.org, Cc: Martin K . Petersen <martin.petersen@oracle.com>, Cc: Christoph Hellwig <hch@lst.de>, Cc: James E . J . Bottomley <jejb@linux.vnet.ibm.com>, Reported-by: James Smart <james.smart@broadcom.com> Fixes: 45a9c9d909b2 ("blk-mq: Fix a use-after-free") Cc: stable@vger.kernel.org Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Tested-by: James Smart <james.smart@broadcom.com> Signed-off-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
After commit 396eaf21ee17 ("blk-mq: improve DM's blk-mq IO merging via
blk_insert_cloned_request feedback"), map_request() will requeue the tio
when issued clone request return BLK_STS_RESOURCE or BLK_STS_DEV_RESOURCE.
Thus, if device driver status is error, a tio may be requeued multiple
times until the return value is not DM_MAPIO_REQUEUE. That means
type->start_io may be called multiple times, while type->end_io is only
called when IO complete.
In fact, even without commit 396eaf21ee17, setup_clone() failure can
also cause tio requeue and associated missed call to type->end_io.
The service-time path selector selects path based on in_flight_size,
which is increased by st_start_io() and decreased by st_end_io().
Missed calls to st_end_io() can lead to in_flight_size count error and
will cause the selector to make the wrong choice. In addition,
queue-length path selector will also be affected.
To fix the problem, call type->end_io in ->release_clone_rq before tio
requeue. map_info is passed to ->release_clone_rq() for map_request()
error path that result in requeue.
Add the blocks which belong to the journal inode to block_validity's
system zone so attempts to deallocate or overwrite the journal due a
corrupted file system where the journal blocks are also claimed by
another inode.
There is a KASAN slab-out-of-bounds:
BUG: KASAN: slab-out-of-bounds in _copy_from_iter_full+0x783/0xaa0
Read of size 80 at addr ffff88810c35e180 by task mount.cifs/539
It can be reproduced by the following step:
1. samba configured with: server max protocol = SMB2_10
2. mount -o vers=default
When parse the mount version parameter, the 'ops' and 'vals'
was setted to smb30, if negotiate result is smb21, just
update the 'ops' to smb21, but the 'vals' is still smb30.
When add lease context, the iov_base is allocated with smb21
ops, but the iov_len is initiallited with the smb30. Because
the iov_len is longer than iov_base, when send the message,
copy array out of bounds.
we need to keep the 'ops' and 'vals' consistent.
Fixes: 9764c02fcbad ("SMB3: Add support for multidialect negotiate (SMB2.1 and later)") Fixes: d5c7076b772a ("smb3: add smb3.1.1 to default dialect list") Signed-off-by: ZhangXiaoxu <zhangxiaoxu5@huawei.com> Signed-off-by: Steve French <stfrench@microsoft.com> CC: Stable <stable@vger.kernel.org> Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Invoking the 64-bit variation on a 32-bit kenrel will crash the guest,
trigger a WARN, and/or lead to a buffer overrun in the host, e.g.
rsm_load_state_64() writes r8-r15 unconditionally, but enum kvm_reg and
thus x86_emulate_ctxt._regs only define r8-r15 for CONFIG_X86_64.
KVM allows userspace to report long mode support via CPUID, even though
the guest is all but guaranteed to crash if it actually tries to enable
long mode. But, a pure 32-bit guest that is ignorant of long mode will
happily plod along.
SMM complicates things as 64-bit CPUs use a different SMRAM save state
area. KVM handles this correctly for 64-bit kernels, e.g. uses the
legacy save state map if userspace has hid long mode from the guest,
but doesn't fare well when userspace reports long mode support on a
32-bit host kernel (32-bit KVM doesn't support 64-bit guests).
Since the alternative is to crash the guest, e.g. by not loading state
or explicitly requesting shutdown, unconditionally use the legacy SMRAM
save state map for 32-bit KVM. If a guest has managed to get far enough
to handle SMIs when running under a weird/buggy userspace hypervisor,
then don't deliberately crash the guest since there are no downsides
(from KVM's perspective) to allow it to continue running.
Fixes: 660a5d517aaab ("KVM: x86: save/load state on SMM switch") Cc: stable@vger.kernel.org Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In this case, host_xcr0 is 0x2ff, guest vcpu xcr0 is 0xff. After schedule
out, host cpu has guest xcr0 loaded (0xff).
In __switch_to {
switch_fpu_finish
copy_kernel_to_fpregs
XRSTORS
If any bit i in XSTATE_BV[i] == 1 and xcr0[i] == 0, XRSTORS will
generate #GP (In this case, bit 9). Then ex_handler_fprestore kicks in
and tries to reinitialize fpu by restoring init fpu state. Same story as
last #GP, except we get DOUBLE FAULT this time.
Cc: stable@vger.kernel.org Signed-off-by: WANG Chao <chao.wang@ucloud.cn> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
KVM bases its memory usage limits on the total number of guest pages
across all memslots. However, those limits, and the calculations to
produce them, use 32 bit unsigned integers. This can result in overflow
if a VM has more guest pages that can be represented by a u32. As a
result of this overflow, KVM can use a low limit on the number of MMU
pages it will allocate. This makes KVM unable to map all of guest memory
at once, prompting spurious faults.
Tested: Ran all kvm-unit-tests on an Intel Haswell machine. This patch
introduced no new failures.
Signed-off-by: Ben Gardon <bgardon@google.com> Cc: stable@vger.kernel.org Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If page-fault handler spans multiple MRs then the access mask needs to
be reset before each MR handling or otherwise write access will be
granted to mapped pages instead of read-only.
Cc: <stable@vger.kernel.org> # 3.19 Fixes: 7bdf65d411c1 ("IB/mlx5: Handle page faults") Reported-by: Jerome Glisse <jglisse@redhat.com> Signed-off-by: Moni Shoua <monis@mellanox.com> Signed-off-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
We assumed that vm_mmap() would reject an attempt to mmap past the end of
the filp (our object), but we were wrong.
Applications that tried to use the mmap beyond the end of the object
would be greeted by a SIGBUS. After this patch, those applications will
be told about the error on creating the mmap, rather than at a random
moment on later access.
Reported-by: Antonio Argenziano <antonio.argenziano@intel.com>
Testcase: igt/gem_mmap/bad-size Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Antonio Argenziano <antonio.argenziano@intel.com> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Cc: stable@vger.kernel.org Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190314075829.16838-1-chris@chris-wilson.co.uk
(cherry picked from commit 794a11cb67201ad1bb61af510bb8460280feb3f3) Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If we don't find a writable file handle when retrying writepages
we break of the loop and do not unlock and put pages neither from
wdata2 nor from the original wdata. Fix this by walking through
all the remaining pages and cleanup them properly.
Cc: <stable@vger.kernel.org> Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This patch aims to address writeback code problems related to error
paths. In particular it respects EINTR and related error codes and
stores and returns the first error occurred during writeback.
Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com> Acked-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Acquiring the reset GPIO low means that reset is being deasserted, this
is followed almost immediately with qcom_pcie_host_init() asserting it,
initializing it and then finally deasserting it again, for the link to
come up.
Some PCIe devices requires a minimum time between the initial deassert
and subsequent reset cycles. In a platform that boots with the reset
GPIO asserted this requirement is being violated by this deassert/assert
pulse.
Acquire the reset GPIO high to prevent this situation by matching the
state to the subsequent asserted state.
The scrub_ctx csum_list member must be initialized before scrub_free_ctx
is called. If the csum_list is not initialized beforehand, the
list_empty call in scrub_free_csums will result in a null deref if the
allocation fails in the for loop.
Fixes: a2de733c78fa ("btrfs: scrub") CC: stable@vger.kernel.org # 3.0+ Reviewed-by: Nikolay Borisov <nborisov@suse.com> Signed-off-by: Dan Robertson <dan@dlrobertson.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This fixes card initialization failure in high speed mode.
If U-Boot uses SDR or HS200/400 mode before starting Linux and Linux
DT does not enable SDR/HS200/HS400 mode, card initialization fails in
high speed mode.
It is necessary to initialize SCC registers during card initialization
phase. HW reset function is registered only for a port with either of
SDR/HS200/HS400 properties in device tree. If SDR/HS200/HS400 properties
are not present in device tree, SCC registers will not be reset. In SoC
that support SCC registers, HW reset function should be registered
regardless of the configuration of device tree.
Reproduction procedure:
- Use U-Boot that support MMC HS200/400 mode.
- Delete HS200/HS400 properties in device tree.
(Delete mmc-hs200-1_8v and mmc-hs400-1_8v)
- MMC port works high speed mode and all commands fail.
Signed-off-by: Takeshi Saito <takeshi.saito.xv@renesas.com> Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Cc: Simon Horman <horms+renesas@verge.net.au> Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When the hash MMU is active the AMR, IAMR and UAMOR are used for
pkeys. The AMR is directly writable by user space, and the UAMOR masks
those writes, meaning both registers are effectively user register
state. The IAMR is used to create an execute only key.
Also we must maintain the value of at least the AMR when running in
process context, so that any memory accesses done by the kernel on
behalf of the process are correctly controlled by the AMR.
Although we are correctly switching all registers when going into a
guest, on returning to the host we just write 0 into all regs, except
on Power9 where we restore the IAMR correctly.
This could be observed by a user process if it writes the AMR, then
runs a guest and we then return immediately to it without
rescheduling. Because we have written 0 to the AMR that would have the
effect of granting read/write permission to pages that the process was
trying to protect.
In addition, when using the Radix MMU, the AMR can prevent inadvertent
kernel access to userspace data, writing 0 to the AMR disables that
protection.
So save and restore AMR, IAMR and UAMOR.
Fixes: cf43d3b26452 ("powerpc: Enable pkey subsystem") Cc: stable@vger.kernel.org # v4.16+ Signed-off-by: Russell Currey <ruscur@russell.cc> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Acked-by: Paul Mackerras <paulus@ozlabs.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
VMs may show incorrect uptime and dmesg printk offsets on hypervisors with
unstable clock. The problem is produced when VM is rebooted without exiting
from qemu.
The fix is to calculate clock offset not only for stable clock but for
unstable clock as well, and use kvm_sched_clock_read() which substracts
the offset for both clocks.
This is safe, because pvclock_clocksource_read() does the right thing and
makes sure that clock always goes forward, so once offset is calculated
with unstable clock, we won't get new reads that are smaller than offset,
and thus won't get negative results.
Thank you Jon DeVree for helping to reproduce this issue.
This is much louder then we want. VCPI allocation failures are quite
normal, since they will happen if any part of the modesetting process is
interrupted by removing the DP MST topology in question. So just print a
debugging message on VCPI failures instead.
Signed-off-by: Lyude Paul <lyude@redhat.com> Fixes: f479c0ba4a17 ("drm/nouveau/kms/nv50: initial support for DP 1.2 multi-stream") Cc: Ben Skeggs <bskeggs@redhat.com> Cc: dri-devel@lists.freedesktop.org Cc: nouveau@lists.freedesktop.org Cc: <stable@vger.kernel.org> # v4.10+ Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Exynos4212 and Exynos4412 have only four ADC channels so using
"samsung,exynos-adc-v1" compatible (for eight channels ADCv1) on them is
wrong. Add a new compatible for Exynos4x12.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The vCPU-run asm blob does a manual comparison of a VMCS' launched
status to execute the correct VM-Enter instruction, i.e. VMLAUNCH vs.
VMRESUME. The launched flag is a bool, which is a typedef of _Bool.
C99 does not define an exact size for _Bool, stating only that is must
be large enough to hold '0' and '1'. Most, if not all, compilers use
a single byte for _Bool, including gcc[1].
Originally, 'launched' was of type 'int' and so the asm blob used 'cmpl'
to check the launch status. When 'launched' was moved to be stored on a
per-VMCS basis, struct vcpu_vmx's "temporary" __launched flag was added
in order to avoid having to pass the current VMCS into the asm blob.
The new '__launched' was defined as a 'bool' and not an 'int', but the
'cmp' instruction was not updated.
This has not caused any known problems, likely due to compilers aligning
variables to 4-byte or 8-byte boundaries and KVM zeroing out struct
vcpu_vmx during allocation. I.e. vCPU-run accesses "junk" data, it just
happens to always be zero and so doesn't affect the result.
Stale && dirty keys can be produced in the follow way:
After writeback in write_dirty_finish(), dirty keys k1 will
replace by clean keys k2
==>ret = bch_btree_insert(dc->disk.c, &keys, NULL, &w->key);
==>btree_insert_fn(struct btree_op *b_op, struct btree *b)
==>static int bch_btree_insert_node(struct btree *b,
struct btree_op *op,
struct keylist *insert_keys,
atomic_t *journal_ref,
Then two steps:
A) update k1 to k2 in btree node memory;
bch_btree_insert_keys(b, op, insert_keys, replace_key)
B) Write the bset(contains k2) to cache disk by a 30s delay work
bch_btree_leaf_dirty(b, journal_ref).
But before the 30s delay work write the bset to cache device,
these things happened:
A) GC works, and reclaim the bucket k2 point to;
B) Allocator works, and invalidate the bucket k2 point to,
and increase the gen of the bucket, and place it into free_inc
fifo;
C) Until now, the 30s delay work still does not finish work,
so in the disk, the key still is k1, it is dirty and stale
(its gen is smaller than the gen of the bucket). and then the
machine power off suddenly happens;
D) When the machine power on again, after the btree reconstruction,
the stale dirty key appear.
In bch_extent_bad(), when expensive_debug_checks is off, it would
treat the dirty key as good even it is stale keys, and it would
cause bellow probelms:
A) In read_dirty() it would cause machine crash:
BUG_ON(ptr_stale(dc->disk.c, &w->key, 0));
B) It could be worse when reads hits stale dirty keys, it would
read old incorrect data.
This patch tolerate the existence of these stale && dirty keys,
and treat them as bad key in bch_extent_bad().
(Coly Li: fix indent which was modified by sender's email client)
In extents.c:bch_extent_bad(), number 96 is used as parameter to call
btree_bug_on(). The purpose is to check whether stale gen value exceeds
BUCKET_GC_GEN_MAX, so it is better to use macro BUCKET_GC_GEN_MAX to
make the code more understandable.
Signed-off-by: Coly Li <colyli@suse.de> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
* Rename TPM_BUFSIZE defined in drivers/char/tpm/st33zp24/st33zp24.h to
ST33ZP24_BUFSIZE.
* Rename TPM_BUFSIZE defined in drivers/char/tpm/tpm_i2c_infineon.c to
TPM_I2C_INFINEON_BUFSIZE.
* Rename TPM_RETRY in tpm_i2c_nuvoton to TPM_I2C_RETRIES.
* Remove TPM_HEADER_SIZE from tpm_i2c_nuvoton.
Cc: stable@vger.kernel.org Fixes: bf38b8710892 ("tpm/tpm_i2c_stm_st33: Split tpm_i2c_tpm_st33 in 2 layers (core + phy)") Fixes: aad628c1d91a ("char/tpm: Add new driver for Infineon I2C TIS TPM") Fixes: 32d33b29ba07 ("TPM: Retry SaveState command in suspend path") Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
INTEL_SOC_PMIC, INTEL_SOC_PMIC_CHTWC and MFD_TPS68470 select the
I2C_DESIGNWARE_PLATFORM without its dependencies making it possible to see
warning and build error like below:
WARNING: unmet direct dependencies detected for I2C_DESIGNWARE_PLATFORM
Depends on [n]: I2C [=y] && HAS_IOMEM [=y] && (ACPI [=y] && COMMON_CLK [=n] || !ACPI [=y])
Selected by [y]:
- MFD_TPS68470 [=y] && HAS_IOMEM [=y] && ACPI [=y] && I2C [=y]=y
/usr/bin/ld: drivers/i2c/busses/i2c-designware-platdrv.o: in function `dw_i2c_plat_resume':
i2c-designware-platdrv.c:(.text+0x62): undefined reference to `i2c_dw_prepare_clk'
/usr/bin/ld: drivers/i2c/busses/i2c-designware-platdrv.o: in function `dw_i2c_plat_suspend':
i2c-designware-platdrv.c:(.text+0x9a): undefined reference to `i2c_dw_prepare_clk'
/usr/bin/ld: drivers/i2c/busses/i2c-designware-platdrv.o: in function `dw_i2c_plat_probe':
i2c-designware-platdrv.c:(.text+0x41c): undefined reference to `i2c_dw_prepare_clk'
/usr/bin/ld: i2c-designware-platdrv.c:(.text+0x438): undefined reference to `i2c_dw_read_comp_param'
/usr/bin/ld: i2c-designware-platdrv.c:(.text+0x545): undefined reference to `i2c_dw_probe'
/usr/bin/ld: i2c-designware-platdrv.c:(.text+0x727): undefined reference to `i2c_dw_probe_slave'
Fix this by making above options to depend on I2C_DESIGNWARE_PLATFORM
being built-in. I2C_DESIGNWARE_PLATFORM is a visible symbol with
dependencies so in general the select should be avoided.
Fixes: acebcff9eda8 ("mfd: intel_soc_pmic: Select designware i2c-bus driver") Fixes: de85d79f4aab ("mfd: Add Cherry Trail Whiskey Cove PMIC driver") Fixes: 9bbf6a15ce19 ("mfd: Add support for TPS68470 device") Cc: Stable <stable@vger.kernel.org> # v4.14+ Reported-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
On i965gm we need to adjust max_vblank_count dynamically
depending on whether the TV encoder is used or not. To
that end add a per-crtc max_vblank_count that takes
precedence over its device wide counterpart. The driver
can now call drm_crtc_set_max_vblank_count() to configure
the per-crtc value before calling drm_vblank_on().
Also looks like there was some discussion about exynos needing
similar treatment.
v2: Drop the extra max_vblank_count!=0 check for the
WARN(last!=current), will take care of it in i915 code (Daniel)
WARN_ON(!inmodeset) (Daniel)
WARN_ON(dev->max_vblank_count)
Pimp up the docs (Daniel)
Cc: stable@vger.kernel.org Cc: Inki Dae <inki.dae@samsung.com> Cc: Daniel Vetter <daniel@ffwll.ch> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20181127182004.28885-1-ville.syrjala@linux.intel.com Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The async_file might be freed before the disassociation has been ended,
causing qp shutdown to use after free on it.
Since uverbs_destroy_ufile_hw is not a fence, it returns if a
disassociation is ongoing in another thread. It has to be written this way
to avoid deadlock. However this means that the ufile FD close cannot
destroy anything that may still be used by an active kref, such as the the
async_file.
To fix that move the kref_put() to be in ib_uverbs_release_file().
Cc: <stable@vger.kernel.org> # 4.2 Fixes: 036b10635739 ("IB/uverbs: Enable device removal when there are active user space applications") Signed-off-by: Yishai Hadas <yishaih@mellanox.com> Signed-off-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
do_page_fault() forgot to relinquish mmap_sem if a signal came while
handling handle_mm_fault() - due to say a ctl+c or oom etc.
This would later cause a deadlock by acquiring it twice.
This came to light when running libc testsuite tst-tls3-malloc test but
is likely also the cause for prior seen LTP failures. Using lockdep
clearly showed what the issue was.
| # while true; do ./tst-tls3-malloc ; done
| Didn't expect signal from child: got `Segmentation fault'
| ^C
| ============================================
| WARNING: possible recursive locking detected
| 4.17.0+ #25 Not tainted
| --------------------------------------------
| tst-tls3-malloc/510 is trying to acquire lock:
| 606c7728 (&mm->mmap_sem){++++}, at: __might_fault+0x28/0x5c
|
|but task is already holding lock:
|606c7728 (&mm->mmap_sem){++++}, at: do_page_fault+0x9c/0x2a0
|
| other info that might help us debug this:
| Possible unsafe locking scenario:
|
| CPU0
| ----
| lock(&mm->mmap_sem);
| lock(&mm->mmap_sem);
|
| *** DEADLOCK ***
|
------------------------------------------------------------
What the change does is not obvious (note to myself)
prior code was
| do_page_fault
|
| down_read() <-- lock taken
| handle_mm_fault <-- signal pending as this runs
| if fatal_signal_pending
| if VM_FAULT_ERROR
| up_read
| if user_mode
| return <-- lock still held, this was the BUG
New code
| do_page_fault
|
| down_read() <-- lock taken
| handle_mm_fault <-- signal pending as this runs
| if fatal_signal_pending
| if VM_FAULT_RETRY
| return <-- not same case as above, but still OK since
| core mm already relinq lock for FAULT_RETRY
| ...
|
| < Now falls through for bug case above >
|
| up_read() <-- lock relinquished
signal handling core calls show_regs() with preemption disabled which
on ARC takes mmap_sem for mm/vma access, causing lockdep splat.
| [ARCLinux]# ./segv-null-ptr
| potentially unexpected fatal signal 11.
| BUG: sleeping function called from invalid context at kernel/fork.c:1011
| in_atomic(): 1, irqs_disabled(): 0, pid: 70, name: segv-null-ptr
| no locks held by segv-null-ptr/70.
| CPU: 0 PID: 70 Comm: segv-null-ptr Not tainted 4.18.0+ #69
|
| Stack Trace:
| arc_unwind_core+0xcc/0x100
| ___might_sleep+0x17a/0x190
| mmput+0x16/0xb8
| show_regs+0x52/0x310
| get_signal+0x5ee/0x610
| do_signal+0x2c/0x218
| resume_user_mode_begin+0x90/0xd8
Workaround by re-enabling preemption temporarily.
Note that the preemption disabling in core code around show_regs()
was introduced by commit 3a9f84d354ce ("signals, debug: fix BUG: using
smp_processor_id() in preemptible code in print_fatal_signal()")
to silence a differnt lockdep seen on x86 bakc in 2009.
cancel_delayed_work_sync() was called for any queue, but it should only
be called for the queue that is associated with the currently running job.
Otherwise, if two filehandles are streaming at the same time, then closing the
first will cancel the work which might still be running for a job from the
second filehandle. As a result the second filehandle will never be able to
finish the job and an attempt to stop streaming on that second filehandle will
stall.
Fixes: 52117be68b82 ("media: vim2m: use cancel_delayed_work_sync instead of flush_schedule_work") Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Cc: <stable@vger.kernel.org> # for v4.20 and up Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
For SAS3 and later controllers, FW sets the reset adapter bit indicating
the driver to perform a controller reset. Driver needs to check if this
bit is set before doing a reset. This reduces the driver probe failure
time to 180seconds in case there is a faulty controller connected.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com> Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
For Invader series, if FW supports more than 8 MSI-x vectors, driver needs
to enable combined reply queue mode. For Ventura series, driver enables
combined reply queue mode in case of more than 16 MSI-x vectors.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com> Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This happens because during page writeback it's valid for
writepage_delalloc to instantiate a delalloc range which doesn't belong
to the page currently being written back.
The reason this case is valid is due to find_lock_delalloc_range
returning any available range after the passed delalloc_start and
ignoring whether the page under writeback is within that range.
In turn ordered extents (OE) are always created for the returned range
from find_lock_delalloc_range. If, however, a failure occurs while OE
are being created then the clean up code in btrfs_cleanup_ordered_extents
will be called.
Unfortunately the code in btrfs_cleanup_ordered_extents doesn't consider
the case of such 'foreign' range being processed and instead it always
assumes that the range OE are created for belongs to the page. This
leads to the first page of such foregin range to not be cleaned up since
it's deliberately missed and skipped by the current cleaning up code.
Fix this by correctly checking whether the current page belongs to the
range being instantiated and if so adjsut the range parameters passed
for cleaning up. If it doesn't, then just clean the whole OE range
directly.
Fixes: 524272607e88 ("btrfs: Handle delalloc error correctly to avoid ordered extent hang") CC: stable@vger.kernel.org # 4.14+ Reviewed-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Nikolay Borisov <nborisov@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This callback is called only from writepage_delalloc which in turn is
guaranteed to be called from the data page writeout path. In the end
there is no reason to have the call to this function to be indrected via
the extent_io_ops structure. This patch removes the callback definition,
exports the function and calls it directly. No functional changes.
Reviewed-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Nikolay Borisov <nborisov@suse.com> Reviewed-by: David Sterba <dsterba@suse.com>
[ rename to btrfs_run_delalloc_range ] Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When a transaction commit starts, it attempts to pause scrub and it blocks
until the scrub is paused. So while the transaction is blocked waiting for
scrub to pause, we can not do memory allocation with GFP_KERNEL from scrub,
otherwise we risk getting into a deadlock with reclaim.
Checking for scrub pause requests is done early at the beginning of the
while loop of scrub_stripe() and later in the loop, scrub_extent() and
scrub_raid56_parity() are called, which in turn call scrub_pages() and
scrub_pages_for_parity() respectively. These last two functions do memory
allocations using GFP_KERNEL. Same problem could happen while scrubbing
the super blocks, since it calls scrub_pages().
We also can not have any of the worker tasks, created by the scrub task,
doing GFP_KERNEL allocations, because before pausing, the scrub task waits
for all the worker tasks to complete (also done at scrub_stripe()).
So make sure GFP_NOFS is used for the memory allocations because at any
time a scrub pause request can happen from another task that started to
commit a transaction.
Fixes: 58c4e173847a ("btrfs: scrub: use GFP_KERNEL on the submission path") CC: stable@vger.kernel.org # 4.6+ Reviewed-by: Nikolay Borisov <nborisov@suse.com> Signed-off-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Testing has revealed an occasional crash which appears to be caused
by a race between kvmppc_switch_mmu_to_hpt and kvm_unmap_hva_range_hv.
The symptom is a NULL pointer dereference in __find_linux_pte() called
from kvm_unmap_radix() with kvm->arch.pgtable == NULL.
Looking at kvmppc_switch_mmu_to_hpt(), it does indeed clear
kvm->arch.pgtable (via kvmppc_free_radix()) before setting
kvm->arch.radix to NULL, and there is nothing to prevent
kvm_unmap_hva_range_hv() or the other MMU callback functions from
being called concurrently with kvmppc_switch_mmu_to_hpt() or
kvmppc_switch_mmu_to_radix().
This patch therefore adds calls to spin_lock/unlock on the kvm->mmu_lock
around the assignments to kvm->arch.radix, and makes sure that the
partition-scoped radix tree or HPT is only freed after changing
kvm->arch.radix.
This also takes the kvm->mmu_lock in kvmppc_rmap_reset() to make sure
that the clearing of each rmap array (one per memslot) doesn't happen
concurrently with use of the array in the kvm_unmap_hva_range_hv()
or the other MMU callbacks.
Fixes: 18c3640cefc7 ("KVM: PPC: Book3S HV: Add infrastructure for running HPT guests on radix host") Cc: stable@vger.kernel.org # v4.15+ Signed-off-by: Paul Mackerras <paulus@ozlabs.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If we fail during GEM initialisation, we scrub the HW state by
performing a device level GPU resuet. However, we want to leave the
system in a usable state (with functioning KMS but no GEM) so after
scrubbing the HW state, we need to restore some sane defaults and
re-enable the low-level common parts of the GPU (such as the GMCH).
v2: Restore GTT entries.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Link: https://patchwork.freedesktop.org/patch/msgid/20180726085033.4044-2-chris@chris-wilson.co.uk Reviewed-by: Michał Winiarski <michal.winiarski@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Since commit eb3744a2dd01 ("gpio: davinci: Do not assume continuous
IRQ numbering") the davinci GPIO driver fails to probe if we boot
in legacy mode from any of the board files. Since the driver now
expects every interrupt to be defined as a separate resource, split
the definition of IRQ resources instead of having a single continuous
interrupt range.
Fixes: eb3744a2dd01 ("gpio: davinci: Do not assume continuous IRQ numbering") Cc: stable@vger.kernel.org Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Signed-off-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Since commit eb3744a2dd01 ("gpio: davinci: Do not assume continuous
IRQ numbering") the davinci GPIO driver fails to probe if we boot
in legacy mode from any of the board files. Since the driver now
expects every interrupt to be defined as a separate resource, split
the definition of IRQ resources instead of having a single continuous
interrupt range.
Fixes: eb3744a2dd01 ("gpio: davinci: Do not assume continuous IRQ numbering") Cc: stable@vger.kernel.org Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Signed-off-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Since commit eb3744a2dd01 ("gpio: davinci: Do not assume continuous
IRQ numbering") the davinci GPIO driver fails to probe if we boot
in legacy mode from any of the board files. Since the driver now
expects every interrupt to be defined as a separate resource, split
the definition of IRQ resources instead of having a single continuous
interrupt range.
Fixes: eb3744a2dd01 ("gpio: davinci: Do not assume continuous IRQ numbering") Cc: stable@vger.kernel.org Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Signed-off-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Since commit eb3744a2dd01 ("gpio: davinci: Do not assume continuous
IRQ numbering") the davinci GPIO driver fails to probe if we boot
in legacy mode from any of the board files. Since the driver now
expects every interrupt to be defined as a separate resource, split
the definition of IRQ resources instead of having a single continuous
interrupt range.
Fixes: eb3744a2dd01 ("gpio: davinci: Do not assume continuous IRQ numbering") Cc: stable@vger.kernel.org Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Signed-off-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Since commit eb3744a2dd01 ("gpio: davinci: Do not assume continuous
IRQ numbering") the davinci GPIO driver fails to probe if we boot
in legacy mode from any of the board files. Since the driver now
expects every interrupt to be defined as a separate resource, split
the definition of IRQ resources instead of having a single continuous
interrupt range.
Fixes: eb3744a2dd01 ("gpio: davinci: Do not assume continuous IRQ numbering") Cc: stable@vger.kernel.org Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Signed-off-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Path property is used for userspace to know what MST connector goes to what actual DRM DisplayPort connector, the tiling property is for tiling configurations. Not sure what else there is to figure out.
Signed-off-by: Lyude Paul <lyude@redhat.com> Reviewed-by: Jerry (Fangzhi) Zuo <Jerry.Zuo@amd.com> Cc: Stable <stable@vger.kernel.org> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In kvp_send_key(), we do need call process_ib_ipinfo() if
message->kvp_hdr.operation is KVP_OP_GET_IP_INFO, because it turns out
the userland hv_kvp_daemon needs the info of operation, adapter_id and
addr_family. With the incorrect fc62c3b1977d, the host can't get the
VM's IP via KVP.
And, fc62c3b1977d added a "break;", but actually forgot to initialize
the key_size/value in the case of KVP_OP_SET, so the default key_size of
0 is passed to the kvp daemon, and the pool files
/var/lib/hyperv/.kvp_pool_* can't be updated.
This patch effectively rolls back the previous fc62c3b1977d, and
correctly fixes the "this statement may fall through" warnings.
This patch is tested on WS 2012 R2 and 2016.
Fixes: fc62c3b1977d ("Drivers: hv: kvp: Fix two "this statement may fall through" warnings") Signed-off-by: Dexuan Cui <decui@microsoft.com> Cc: K. Y. Srinivasan <kys@microsoft.com> Cc: Stephen Hemminger <sthemmin@microsoft.com> Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com> Cc: <Stable@vger.kernel.org> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
With the exception of modesets which would switch the DPMS state of a
connector from on to off, we want to make sure that we disallow all
modesets which would result in enabling a new monitor or a new mode
configuration on a monitor if the connector for the display in question
is no longer registered. This allows us to stop userspace from trying to
enable new displays on connectors for an MST topology that were just
removed from the system, without preventing userspace from disabling
DPMS on those connectors.
Changes since v5:
- Fix typo in comment, nothing else
Signed-off-by: Lyude Paul <lyude@redhat.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: stable@vger.kernel.org Link: https://patchwork.freedesktop.org/patch/msgid/20181008232437.5571-2-lyude@redhat.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If BIOS configured a Y tiled FB we failed to set up the backing object
tiling accordingly, leading to a lack of GT fence installed and a
garbled console.
The problem was bisected to
commit 011f22eb545a ("drm/i915: Do NOT skip the first 4k of stolen memory for pre-allocated buffers v2")
but it just revealed a pre-existing issue.
Kudos to Ville who suspected a missing fence looking at the corruption
on the screen.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Mika Westerberg <mika.westerberg@linux.intel.com> Cc: Hans de Goede <hdegoede@redhat.com> Cc: <ronald@innovation.ch> Cc: <stable@vger.kernel.org> Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reported-by: <ronald@innovation.ch> Tested-by: <ronald@innovation.ch>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=108264 Fixes: bc8d7dffacb1 ("drm/i915/skl: Provide a Skylake version of get_plane_config()") Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20181016160011.28347-1-imre.deak@intel.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Currently, i915 appears to rely on blocking modesets on
no-longer-present MSTB ports by simply returning NULL for
->best_encoder(), which in turn causes any new atomic commits that don't
disable the CRTC to fail. This is wrong however, since we still want to
allow userspace to disable CRTCs on no-longer-present MSTB ports by
changing the DPMS state to off and this still requires that we retrieve
an encoder.
So, fix this by always returning a valid encoder regardless of the state
of the MST port.
Changes since v1:
- Remove mst atomic helper, since this got replaced with a much simpler
solution
Signed-off-by: Lyude Paul <lyude@redhat.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: stable@vger.kernel.org Link: https://patchwork.freedesktop.org/patch/msgid/20181008232437.5571-6-lyude@redhat.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
> Virtual processors are identified by using an index (VP index). The
> maximum number of virtual processors per partition supported by the
> current implementation of the hypervisor can be obtained through CPUID
> leaf 0x40000005. A virtual processor index must be less than the
> maximum number of virtual processors per partition.
Forbid userspace to set VP_INDEX above KVM_MAX_VCPUS. get_vcpu_by_vpidx()
can now be optimized to bail early when supplied vpidx is >= KVM_MAX_VCPUS.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Reviewed-by: Roman Kagan <rkagan@virtuozzo.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The memory ownership transfer request is performed using SCM, ensure
that SCM is available before we probe the driver if memory protection is
needed by the subsystem.
Fixes: 6c5a9dc2481b ("remoteproc: qcom: Make secure world call for mem ownership switch") Cc: stable@vger.kernel.org Signed-off-by: Brian Norris <briannorris@chromium.org>
[bjorn: Added condition for need_mem_protection, updated commit message] Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
We don't need to call process_ib_ipinfo() if message->kvp_hdr.operation is
KVP_OP_GET_IP_INFO in kvp_send_key(), because here we just need to pass on
the op code from the host to the userspace; when the userspace returns
the info requested by the host, we pass the info on to the host in
kvp_respond_to_host() -> process_ob_ipinfo(). BTW, the current buggy code
actually doesn't cause any harm, because only message->kvp_hdr.operation
is used by the userspace, in the case of KVP_OP_GET_IP_INFO.
The patch also adds a missing "break;" in kvp_send_key(). BTW, the current
buggy code actually doesn't cause any harm, because in the case of
KVP_OP_SET, the unexpected fall-through corrupts
message->body.kvp_set.data.key_size, but that is not really used: see
the definition of struct hv_kvp_exchg_msg_value.
Signed-off-by: Dexuan Cui <decui@microsoft.com> Cc: K. Y. Srinivasan <kys@microsoft.com> Cc: Haiyang Zhang <haiyangz@microsoft.com> Cc: Stephen Hemminger <sthemmin@microsoft.com> Cc: <Stable@vger.kernel.org> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The keyctl_dh_params struct in uapi/linux/keyctl.h contains the symbol
"private" which means that the header file will cause compilation failure
if #included in to a C++ program. Further, the patch that added the same
struct to the keyutils package named the symbol "priv", not "private".
The previous attempt to fix this (commit 8a2336e549d3) did so by simply
renaming the kernel's copy of the field to dh_private, but this then breaks
existing userspace and as such has been reverted (commit 8c0f9f5b309d).
[And note, to those who think that wrapping the struct in extern "C" {}
will work: it won't; that only changes how symbol names are presented to
the assembler and linker.].
Instead, insert an anonymous union around the "private" member and add a
second member in there with the name "priv" to match the one in the
keyutils package. The "private" member is then wrapped in !__cplusplus
cpp-conditionals to hide it from C++.
Fixes: ddbb41148724 ("KEYS: Add KEYCTL_DH_COMPUTE command") Fixes: 8a2336e549d3 ("uapi/linux/keyctl.h: don't use C++ reserved keyword as a struct member name") Signed-off-by: David Howells <dhowells@redhat.com>
cc: Randy Dunlap <rdunlap@infradead.org>
cc: Lubomir Rintel <lkundrak@v3.sk>
cc: James Morris <jmorris@namei.org>
cc: Mat Martineau <mathew.j.martineau@linux.intel.com>
cc: Stephan Mueller <smueller@chronox.de>
cc: Andrew Morton <akpm@linux-foundation.org>
cc: Linus Torvalds <torvalds@linux-foundation.org>
cc: stable@vger.kernel.org Signed-off-by: James Morris <james.morris@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
There is a probability that the SRB structure might have been released by the
time the debug log message dereferences it. This patch moved the log messages
before the command is issued to the firmware to prevent unknown behavior and
kernel crash
Fixes: 726b85487067 ("qla2xxx: Add framework for async fabric discovery") Cc: <stable@vger.kernel.org> Signed-off-by: Giridhar Malavali <giridhar.malavali@cavium.com> Reviewed-by: Ewan D. Milne <emilne@redhat.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Some arches (e.g., arm64, x86) have moved towards non-executable
module_alloc() allocations for security hardening reasons. That means
that the module loader will need to set the text section of a module to
executable, regardless of whether or not CONFIG_STRICT_MODULE_RWX is set.
When CONFIG_STRICT_MODULE_RWX=y, module section allocations are always
page-aligned to handle memory rwx permissions. On some arches with
CONFIG_STRICT_MODULE_RWX=n however, when setting the module text to
executable, the BUG_ON() in frob_text() gets triggered since module
section allocations are not page-aligned when CONFIG_STRICT_MODULE_RWX=n.
Since the set_memory_* API works with pages, and since we need to call
set_memory_x() regardless of whether CONFIG_STRICT_MODULE_RWX is set, we
might as well page-align all module section allocations for ease of
managing rwx permissions of module sections (text, rodata, etc).
Fixes: 2eef1399a866 ("modules: fix BUG when load module with rodata=n") Reported-by: Martin Kaiser <lists@kaiser.cx> Reported-by: Bartosz Golaszewski <brgl@bgdev.pl> Tested-by: David Lechner <david@lechnology.com> Tested-by: Martin Kaiser <martin@kaiser.cx> Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Signed-off-by: Jessica Yu <jeyu@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
arch/x86/kernel/ftrace.c:669:23: error: 'ftrace_jmp_replace' defined but not used [-Werror=unused-function]
The ftrace_jmp_replace() function now only has a single user and should be
simply moved by that user. But looking at the code, it shows that
ftrace_jmp_replace() is similar to ftrace_call_replace() except that instead
of using the opcode of 0xe8 it uses 0xe9. It makes more sense to consolidate
that function into one implementation that both ftrace_jmp_replace() and
ftrace_call_replace() use by passing in the op code separate.
The structure in ftrace_code_union is also modified to replace the "e8"
field with the more appropriate name "op".
Cc: stable@vger.kernel.org Reported-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Arnd Bergmann <arnd@arndb.de> Link: http://lkml.kernel.org/r/20190304200748.1418790-1-arnd@arndb.de Fixes: d2a68c4effd8 ("x86/ftrace: Do not call function graph from dynamic trampolines") Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Commit 33d915d9e8ce ("{nl,mac}80211: allow 4addr AP operation on
crypto controlled devices") has introduced a change which allows
4addr operation on crypto controlled devices (ex: ath10k). This
change has inadvertently impacted the interface combinations logic
on such devices.
General rule is that software interfaces like AP/VLAN should not be
listed under supported interface combinations and should not be
considered during validation of these combinations; because of the
aforementioned change, AP/VLAN interfaces(if present) will be checked
against interfaces supported by the device and blocks valid interface
combinations.
Consider a case where an AP and AP/VLAN are up and running; when a
second AP device is brought up on the same physical device, this AP
will be checked against the AP/VLAN interface (which will not be
part of supported interface combinations of the device) and blocks
second AP to come up.
Add a new API cfg80211_iftype_allowed() to fix the problem, this
API works for all devices with/without SW crypto control.
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org> Fixes: 33d915d9e8ce ("{nl,mac}80211: allow 4addr AP operation on crypto controlled devices") Link: https://lore.kernel.org/r/1563779690-9716-1-git-send-email-mpubbise@codeaurora.org Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
1. Has duplicated internal speakers (0x14 & 0x17) which makes the output
route become confused. So, the output volume cannot be changed by
setting.
2. Misses the headset mic pin node.
This patch disables the confusing speaker (NID 0x14) and enables the
headset mic (NID 0x19).
Clang warns after commit 8985167ecf57 ("clk: s2mps11: Fix matching when
built as module and DT node contains compatible"):
drivers/clk/clk-s2mps11.c:242:34: warning: variable 's2mps11_dt_match'
is not needed and will not be emitted [-Wunneeded-internal-declaration]
static const struct of_device_id s2mps11_dt_match[] = {
^
1 warning generated.
This warning happens when a variable is used in some construct that
doesn't require a reference to that variable to be emitted in the symbol
table; in this case, it's MODULE_DEVICE_TABLE, which only needs to hold
the data of the variable, not the variable itself.
$ nm -S drivers/clk/clk-s2mps11.o | rg s2mps11_dt_match 00000078000003d4 R __mod_of__s2mps11_dt_match_device_table
Normally, with device ID table variables, it means that the variable
just needs to be tied to the device declaration at the bottom of the
file, like s2mps11_clk_id:
$ nm -S drivers/clk/clk-s2mps11.o | rg s2mps11_clk_id 0000000000000078 R __mod_platform__s2mps11_clk_id_device_table 0000000000000078 r s2mps11_clk_id
However, because the comment above this deliberately doesn't want this
variable added to .of_match_table, we need to mark s2mps11_dt_match as
__used to silence this warning. This makes it clear to Clang that the
variable is used for something, even if a reference to it isn't being
emitted.
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Fixes: 8985167ecf57 ("clk: s2mps11: Fix matching when built as module and DT node contains compatible") Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The basepath may contain special characters, which would confuse the regex
matcher. ${var#prefix} does the right thing.
Link: http://lkml.kernel.org/r/20190518055946.181563-1-drinkcat@chromium.org Fixes: 67a28de47faa8358 ("scripts/decode_stacktrace: only strip base path when a prefix of the path") Signed-off-by: Nicolas Boichat <drinkcat@chromium.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
projects / mirror_ubuntu-bionic-kernel.git / log