HID: core: remove the absolute need of hid_have_special_driver[]
BugLink: https://bugs.launchpad.net/bugs/1862567
Most HID devices behave properly when they are used with hid-generic.
Since kernel v4.12, we do not poll for input reports at plug in, so
hid-generic should behave properly with all HID devices.
There has been a long standing list of HID devices that have a special
driver. It used to be just a few, but with time, this list went too big,
and we can not ask users to know which HID special driver will pick up
their device.
We can teach hid-generic to be nice with others. If a device is not
explicitly marked with HID_QUIRK_HAVE_SPECIAL_DRIVER, we can allow
hid-generic to pick up the device as long as no other loaded HID driver
will match the device.
When the special driver appears, hid-generic can step back and let
the special driver handling the device. In case this special driver
is removed, this good old pal of hid-generic will rebind to the device.
This basically makes the list hid_have_special_driver[] useless. It
still allows to not see a hid-generic driver bound and removed during
boot, so we can keep it around.
This will also help other people to have a special HID driver without
the need of recompiling hid-core.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
(cherry picked from commit e04a0442d33b8cf183bba38646447b891bb02123) Signed-off-by: Aaron Ma <aaron.ma@canonical.com> Acked-by: Sultan Alsawaf <sultan.alsawaf@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Note that this change introduces an initial lookup for the device in
hid_gets_squirk(), which should not theoretically be required, but which
actually allows to not have to reparse the list of ignored devices
if we call hid_lookup_quirks twice.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
(backported from commit f745d162f469a4b1e805779a8b0d9157100c813c) Signed-off-by: Aaron Ma <aaron.ma@canonical.com> Acked-by: Sultan Alsawaf <sultan.alsawaf@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
HID: quirks: move the list of special devices into a quirk
BugLink: https://bugs.launchpad.net/bugs/1862567
It is better to centralize the information of special devices in one
single file. Instead of manually parsing the list of devices that
have a special driver or those that need to be ignored, introduce
HID_QUIRK_HAVE_SPECIAL_DRIVER and set the correct quirks while fetching
those quirks.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
(backported from commit 6e65d9d5492f370dd0e5418bdd38265b2ca74f88) Signed-off-by: Aaron Ma <aaron.ma@canonical.com> Acked-by: Sultan Alsawaf <sultan.alsawaf@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
HID: core: move the dynamic quirks handling in core
BugLink: https://bugs.launchpad.net/bugs/1862567
usbhid has a list of dynamic quirks in addition to a list of static quirks.
There is not much USB specific in that, so move this part of the module
in core so we can have one central place for quirks.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
(cherry picked from commit d5d3e202753cc023100a854788a4ad83d7c2821a) Signed-off-by: Aaron Ma <aaron.ma@canonical.com> Acked-by: Sultan Alsawaf <sultan.alsawaf@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
block/blk-mq.c: In function ‘blk_mq_complete_request’:
./include/linux/srcu.h:175:2: warning: ‘srcu_idx’ may be used uninitialized in this function [-Wmaybe-uninitialized]
__srcu_read_unlock(sp, idx);
^
block/blk-mq.c:620:6: note: ‘srcu_idx’ was declared here
int srcu_idx;
^
which is completely bogus, since we only use srcu_idx when
hctx->flags & BLK_MQ_F_BLOCKING is set, and that's the case where
hctx_lock() has initialized it.
Just set it to '0' in the normal path in hctx_lock() to silence
this annoying warning.
Fixes: 04ced159cec8 ("blk-mq: move hctx lock/unlock into a helper") Fixes: 5197c05e16b4 ("blk-mq: protect completion path with RCU") Signed-off-by: Jens Axboe <axboe@kernel.dk>
(backported from commit 08b5a6e2a769f720977b245431b45134c0bdd377) Signed-off-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Colin Ian King <colin.king@canonical.com> Acked-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Juerg Haefliger [Wed, 22 Jan 2020 07:32:00 +0000 (08:32 +0100)]
UBUNTU: [Packaging] Fix config file assembly
Commit 'UBUNTU: [Packaging] dkms -- switch to a consistent build prefix
length and strip' introduced a helper tool fix-filenames which was added as
a prerequisite to the $(stampdir)/stamp-prepare-tree-% rule. This rule
generates the config file by concatenating all prereqs together
(cat $^ ...) including the fix-filenames binary blob which results in
warnings like:
Quentin Monnet [Wed, 20 Nov 2019 11:48:00 +0000 (12:48 +0100)]
UBUNTU: [Debian] package bpftool in linux-tools-common
BugLink: https://bugs.launchpad.net/bugs/1774815
bpftool is a debugging and introspection tool for BPF elements,
developed by the BPF kernel community. Its source code is located in the
kernel repository, at tools/bpf/bpftool. Package it in linux-tools and
linux-tools-common.
Along the binary, package manual pages and bash completion file.
bpftool itself is installed under /usr/sbin/, to be consistent with its
Makefile.
Dependency python3-docutils is added to Build-Depends-Indep, in order to
provide rst2man which is necessary to build bpftool's manual pages.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com> Acked-by: Seth Forshee <seth.forshee@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
BugLink: https://bugs.launchpad.net/bugs/1774815
This keeps giving us problems with introducing unwanted binary
dependencies in linux-tools. These tools will work without these
dependencies, albeit with somewhat reduced functionality. Aside
from that I can't see that this dependency is needed, so let's
try removing it.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
(backported from commit 721d5f0c58073e6133db5dc05cf46200170fd80a) Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com> Acked-by: Seth Forshee <seth.forshee@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
BugLink: https://bugs.launchpad.net/bugs/1774815
Make it possible to build bpftool without libbfd. libbfd and libopcodes are
typically provided in dev/dbg packages (binutils-dev in debian) which we
usually don't have installed on the fleet machines and we'd like a way to have
bpftool version that works without installing any additional packages.
This excludes support for disassembling jit-ted code and prints an error if
the user tries to use these features.
Roman Gushchin [Wed, 20 Nov 2019 11:48:00 +0000 (12:48 +0100)]
tools/bpftool: fix bpftool build with bintutils >= 2.9
BugLink: https://bugs.launchpad.net/bugs/1774815
Bpftool build is broken with binutils version 2.29 and later.
The cause is commit 003ca0fd2286 ("Refactor disassembler selection")
in the binutils repo, which changed the disassembler() function
signature.
Fix this by adding a new "feature" to the tools/build/features
infrastructure and make it responsible for decision which
disassembler() function signature to use.
Signed-off-by: Roman Gushchin <guro@fb.com> Cc: Jakub Kicinski <jakub.kicinski@netronome.com> Cc: Alexei Starovoitov <ast@kernel.org> Cc: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
(backported from commit fb982666e380c1632a74495b68b3c33a66e76430) Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com> Acked-by: Seth Forshee <seth.forshee@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The original intent behind Lockdown's SysRq support was that the SysRq
command to lift Lockdown would only be honored if the command was
physically entered on a keyboard. Attempts to synthetically generate the
SysRq command, by a software program, were to be ignored since software,
even running as root, must not have the authorization to lift Lockdown.
Unfortunately, attempts to detect a synthetic SysRq command can be
thwarted by a privileged process that is able to set up a USB/IP
connection as the USB/IP connection could be used to lift Lockdown.
Remove the ability to lift Lockdown using SysRq.
Signed-off-by: Tyler Hicks <tyhicks@canonical.com> Acked-by: Sultan Alsawaf <sultan.alsawaf@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Chris Wilson [Fri, 10 Nov 2017 14:26:33 +0000 (14:26 +0000)]
drm/i915: Record the default hw state after reset upon load
BugLink: https://bugs.launchpad.net/bugs/1862840
Take a copy of the HW state after a reset upon module loading by
executing a context switch from a blank context to the kernel context,
thus saving the default hw state over the blank context image.
We can then use the default hw state to initialise any future context,
ensuring that each starts with the default view of hw state.
v2: Unmap our default state from the GTT after stealing it from the
context. This should stop us from accidentally overwriting it via the
GTT (and frees up some precious GTT space).
(backported from commit d2b4b97933f5adacfba42dc3b9200d0e21fbe2c4)
[tyhicks: Backport to 4.15:
- The HAS_LOGICAL_RING_PREEMPTION() macro does not exist because we
don't have commit a4598d17551a ("drm/i915: Rename helpers used for
unwinding, use macro for can_preempt")] Signed-off-by: Tyler Hicks <tyhicks@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Acked-by: Timo Aaltonen <timo.aaltonen@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Chris Wilson [Fri, 10 Nov 2017 14:26:32 +0000 (14:26 +0000)]
drm/i915: Mark the context state as dirty/written
BugLink: https://bugs.launchpad.net/bugs/1862840
In the next few patches, we will want to both copy out of the context
image and write a valid image into a new context. To be completely safe,
we should then couple in our domain tracking to ensure that we don't
have any issues with stale data remaining in unwanted cachelines.
Historically, we omitted the .write=true from the call to set-gtt-domain
in i915_switch_context() in order to avoid a stall between every request
as we would want to wait for the previous context write from the gpu.
Since then, we limit the set-gtt-domain to only occur when we first bind
the vma, so once in use we will never stall, and we are sure to flush
the context following a load from swap.
Equally we never applied the lessons learnt from ringbuffer submission
to execlists; so time to apply the flush of the lrc after load as well.
Chris Wilson [Fri, 10 Nov 2017 14:26:31 +0000 (14:26 +0000)]
drm/i915: Inline intel_modeset_gem_init()
BugLink: https://bugs.launchpad.net/bugs/1862840
intel_modeset_gem_init() now only sets up the legacy overlay, so let's
remove the function and call the setup directly during driver load. This
should help us find a better point in the initialisation sequence for it
later.
Chris Wilson [Fri, 10 Nov 2017 14:26:30 +0000 (14:26 +0000)]
drm/i915: Move intel_init_clock_gating() to i915_gem_init()
BugLink: https://bugs.launchpad.net/bugs/1862840
Despite its name intel_init_clock_gating applies both display clock gating
workarounds; GT mmio workarounds and the occasional GT power context
workaround. Worse, sometimes it includes a context register workaround
which we need to apply before we record the default HW state for all
contexts.
Chris Wilson [Fri, 10 Nov 2017 14:26:29 +0000 (14:26 +0000)]
drm/i915: Move GT powersaving init to i915_gem_init()
BugLink: https://bugs.launchpad.net/bugs/1862840
GT powersaving is tightly coupled to the request infrastructure. To
avoid complications with the order of initialisation in the next patch
(where we want to send requests to hw during GEM init) move the
powersaving initialisation into the purview of i915_gem_init().
Chris Wilson [Fri, 10 Nov 2017 14:26:28 +0000 (14:26 +0000)]
drm/i915: Force the switch to the i915->kernel_context
BugLink: https://bugs.launchpad.net/bugs/1862840
In the next few patches, we will have a hard requirement that we emit a
context-switch to the perma-pinned i915->kernel_context (so that we can
save the HW state using that context-switch). As the first context
itself may be classed as a kernel context, we want to be explicit in our
comparison. For an extra-layer of finesse, we can check the last
unretired context on the engine; as well as the last retired context
when idle.
v2: verbose verbosity
v3: Always force the switch, even when the engine is idle, and update
the assert that this happens before suspend.
Tvrtko Ursulin [Fri, 10 Nov 2017 14:26:27 +0000 (14:26 +0000)]
drm/i915: Define an engine class enum for the uABI
BugLink: https://bugs.launchpad.net/bugs/1862840
We want to be able to report back to userspace details about an engine's
class, and in return for userspace to be able to request actions
regarding certain classes of engines. To isolate the uABI from any
variations between hw generations, we define an abstract class for the
engines and internally map onto the hw.
v2: Remove MAX from the uABI; keep it internal if we need it, but don't
let userspace make the mistake of using it themselves.
v3: s/OTHER/INVALID/
The use of OTHER is ill-defined, so remove it from the uABI as any
future new type of engine can define a class to suit it. But keep a
reserved value for an invalid class, so that we can always
unambiguously express when something doesn't belong to the
classification.
Chris Wilson [Tue, 24 Oct 2017 22:08:55 +0000 (23:08 +0100)]
drm/i915: Use same test for eviction and submitting kernel context
BugLink: https://bugs.launchpad.net/bugs/1862840
During evict, we wish to idle the GPU if we see that the GGTT is full.
However, our test for idle in i915_gem_evict_something() and in
i915_gem_switch_to_kernel_context() do not match leading to
disappointment - we never believe that we are idle and keep trying to
flush the GGTT ad infinitum.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=103438 Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Cc: Mika Kuoppala <mika.kuoppala@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20171024220855.30155-2-chris@chris-wilson.co.uk Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
CVE-2020-8832
(cherry picked from commit 20ccd4d3f689ac14dce8632d76769be0ac952060) Signed-off-by: Tyler Hicks <tyhicks@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Acked-by: Timo Aaltonen <timo.aaltonen@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Commit 0ed266d7ae5e ("clk: ti: omap3: cleanup unnecessary clock aliases")
removed old omap3 clock framework aliases but caused omap3-rom-rng to
stop working with clock not found error.
Based on discussions on the mailing list it was requested by Tero Kristo
that it would be best to fix this issue by probing omap3-rom-rng using
device tree to provide a proper clk property. The other option would be
to add back the missing clock alias, but that does not help moving things
forward with removing old legacy platform_data.
Let's also add a proper device tree binding and keep it together with
the fix.
Cc: devicetree@vger.kernel.org Cc: Aaro Koskinen <aaro.koskinen@iki.fi> Cc: Adam Ford <aford173@gmail.com> Cc: Pali Rohár <pali.rohar@gmail.com> Cc: Rob Herring <robh+dt@kernel.org> Cc: Sebastian Reichel <sre@kernel.org> Cc: Tero Kristo <t-kristo@ti.com> Fixes: 0ed266d7ae5e ("clk: ti: omap3: cleanup unnecessary clock aliases") Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi> Signed-off-by: Tony Lindgren <tony@atomide.com> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In afs_wait_for_call_to_complete(), rather than immediately aborting an
operation if a signal occurs, the code attempts to wait for it to
complete, using a schedule timeout of 2*RTT (or min 2 jiffies) and a
check that we're still receiving relevant packets from the server before
we consider aborting the call. We may even ping the server to check on
the status of the call.
However, there's a missing timeout reset in the event that we do
actually get a packet to process, such that if we then get a couple of
short stalls, we then time out when progress is actually being made.
Fix this by resetting the timeout any time we get something to process.
If it's the failure of the call then the call state will get changed and
we'll exit the loop shortly thereafter.
A symptom of this is data fetches and stores failing with EINTR when
they really shouldn't.
Fixes: bc5e3a546d55 ("rxrpc: Use MSG_WAITALL to tell sendmsg() to temporarily ignore signals") Signed-off-by: David Howells <dhowells@redhat.com> Reviewed-by: Marc Dionne <marc.dionne@auristor.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When device stop was moved out of reset, test device wasn't updated to
stop before reset, this resulted in a use after free. Fix by invoking
stop appropriately.
Fixes: b211616d7125 ("vhost: move -net specific code out") Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Without this patch, a command bit in the supported commands mask is only
ever set to unsupported during set online. If a command is ever marked as
unsupported (e.g. because of error during qeth_l2_vnicc_query_cmds),
subsequent successful initialization (offline/online) would not bring it
back.
__find_linux_mm_pte() returns a page table entry pointer after walking
the page table without holding locks. To make it safe against a THP
split and/or collapse, we disable interrupts around the lockless page
table walk. However we need to keep interrupts disabled as long as we
use the page table entry pointer that is returned.
In original codes, the VF index used incorrectly in function
hclge_set_vlan_rx_offload_cfg() and hclge_set_vlan_rx_offload_cfg().
When VF id is greater than 8, for example 9, it will set the
same bit with VF id 1.
This patch fixes it by using vport->vport_id % HCLGE_VF_NUM_PER_CMD /
HCLGE_VF_NUM_PER_BYTE as the array index, instead of vport->vport_id /
HCLGE_VF_NUM_PER_CMD.
Fixes: 052ece6dc19c ("net: hns3: add ethtool related offload command") Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
According to the AST2500/AST2520 specs, these SoCs support up to 228 GPIO
pins. However, 'gpio-ranges' value in 'aspeed-g5.dtsi' file is currently
setting the upper limit to 220 which isn't allowing access to all their
GPIOs. The correct upper limit value is 232 (actual number is 228 plus a
4-GPIO hole in GPIOAB). Without this patch, GPIOs AC5 and AC6 do not work
correctly on a AST2500 BMC running Linux Kernel v4.19
Fixes: 2039f90d136c ("ARM: dts: aspeed-g5: Add gpio controller to devicetree") Signed-off-by: Oscar A Perez <linux@neuralgames.com> Reviewed-by: Andrew Jeffery <andrew@aj.id.au> Signed-off-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When a local endpoint is ceases to be in use, such as when the kafs module
is unloaded, the kernel will emit an assertion failure if there are any
outstanding client connections:
rxrpc: Assertion failed
------------[ cut here ]------------
kernel BUG at net/rxrpc/local_object.c:433!
and even beyond that, will evince other oopses if there are service
connections still present.
Fix this by:
(1) Removing the triggering of connection reaping when an rxrpc socket is
released. These don't actually clean up the connections anyway - and
further, the local endpoint may still be in use through another
socket.
(2) Mark the local endpoint as dead when we start the process of tearing
it down.
(3) When destroying a local endpoint, strip all of its client connections
from the idle list and discard the ref on each that the list was
holding.
(4) When destroying a local endpoint, call the service connection reaper
directly (rather than through a workqueue) to immediately kill off all
outstanding service connections.
(5) Make the service connection reaper reap connections for which the
local endpoint is marked dead.
Only after destroying the connections can we close the socket lest we get
an oops in a workqueue that's looking at a connection or a peer.
Fixes: 3d18cbb7fd0c ("rxrpc: Fix conn expiry timers") Signed-off-by: David Howells <dhowells@redhat.com> Tested-by: Marc Dionne <marc.dionne@auristor.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Since commit ad67b74d2469d9b8 ("printk: hash addresses printed with
%p"), an obfuscated kernel pointer is printed at every boot if
debugging is enabled:
vdso: 1 text pages at base (____ptrval____)
Remove the print completely, as it's useless without the address.
Based on commit 0f1bf7e39822476b ("arm64/vdso: don't leak kernel
addresses").
Fixes: ad67b74d2469d9b8 ("printk: hash addresses printed with %p") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The functions i40e_aq_get_phy_abilities_resp() and i40e_set_fc() both
have giant structure on the stack, which makes each one use stack frames
larger than 500 bytes.
As clang decides one function into the other, we get a warning for
exceeding the frame size limit on 32-bit architectures:
drivers/net/ethernet/intel/i40e/i40e_common.c:1654:23: error: stack frame size of 1116 bytes in function 'i40e_set_fc' [-Werror,-Wframe-larger-than=]
When building with gcc, the inlining does not happen, but i40e_set_fc()
calls i40e_aq_get_phy_abilities_resp() anyway, so they add up on the
kernel stack just as much.
The parts that actually use large stacks don't overlap, so make sure
each one is a separate function, and mark them as noinline_for_stack to
prevent the compilers from combining them again.
Fixes: 0a862b43acc6 ("i40e/i40evf: Add module_types and update_link_info") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
My error handling "cleanup" was totally wrong. Both the "err" and "ret"
variables are required. The "err" variable holds the error codes for
rv3029_eeprom_enter/exit() and the "ret" variable holds the error codes
for if actual write fails. In my patch if the write failed, the
function probably still returned success.
Reported-by: Tom Evans <tom.evans@motec.com.au> Fixes: 97f5b0379c38 ("rtc: rv3029: Clean up error handling in rv3029_eeprom_write()") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Link: https://lore.kernel.org/r/20190817065604.GB29951@mwanda Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The atomic_dec_and_test() is not safe because it is
outside of locks.
Move the locks of t4_smte_free() to its caller,
cxgb4_smt_release() to protect the atomic decrement.
Fixes: 3bdb376e6944 ("cxgb4: introduce SMT ops to prepare for SMAC rewrite support") Signed-off-by: Chuhong Yuan <hslester96@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Fix build warning if drm_panel.h is built with CONFIG_OF=n or
CONFIG_DRM_PANEL=n and included without the prerequisite err.h:
./include/drm/drm_panel.h: In function ‘of_drm_find_panel’:
./include/drm/drm_panel.h:203:9: error: implicit declaration of function ‘ERR_PTR’ [-Werror=implicit-function-declaration]
return ERR_PTR(-ENODEV);
^~~~~~~
./include/drm/drm_panel.h:203:9: error: returning ‘int’ from a function with return type ‘struct drm_panel *’ makes pointer from integer without a cast [-Werror=int-conversion]
return ERR_PTR(-ENODEV);
^~~~~~~~~~~~~~~~
Fixes: 5fa8e4a22182 ("drm/panel: Make of_drm_find_panel() return an ERR_PTR() instead of NULL") Signed-off-by: Jani Nikula <jani.nikula@intel.com> Acked-by: Thierry Reding <treding@nvidia.com> Reviewed-by: Sam Ravnborg <sam@ravnborg.org> Reviewed-by: Sean Paul <sean@poorly.run> Cc: Boris Brezillon <bbrezillon@kernel.org> Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Link: https://patchwork.freedesktop.org/patch/msgid/20190718161507.2047-2-sam@ravnborg.org Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In general, it is not correct to call pm_generic_suspend(),
pm_generic_suspend_late() and pm_generic_suspend_noirq() during the
hibernation's "poweroff" transition, because device drivers may
provide special callbacks to be invoked then and the wrappers in
question cause system suspend callbacks to be run. Unfortunately,
that happens in the ACPI PM domain and ACPI LPSS.
To address this potential issue, introduce "poweroff" callbacks
for the ACPI PM and LPSS that will use pm_generic_poweroff(),
pm_generic_poweroff_late() and pm_generic_poweroff_noirq() as
appropriate.
Fixes: 05087360fd7a (ACPI / PM: Take SMART_SUSPEND driver flag into account) Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
First, after a previous change causing all runtime-suspended devices
in the ACPI PM domain (and ACPI LPSS devices) to be resumed before
creating a snapshot image of memory during hibernation, it is not
necessary to worry about the case in which them might be left in
runtime-suspend any more, so get rid of the code related to that from
ACPI PM domain and ACPI LPSS hibernation callbacks.
Second, it is not correct to use pm_generic_resume_early() and
acpi_subsys_resume_noirq() in hibernation "restore" callbacks (which
currently happens in the ACPI PM domain and ACPI LPSS), so introduce
proper _restore_late and _restore_noirq callbacks for the ACPI PM
domain and ACPI LPSS.
Fixes: 05087360fd7a (ACPI / PM: Take SMART_SUSPEND driver flag into account) Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Both the PCI bus type and the ACPI PM domain avoid resuming
runtime-suspended devices with DPM_FLAG_SMART_SUSPEND set during
hibernation (before creating the snapshot image of system memory),
but that turns out to be a mistake. It leads to functional issues
and adds complexity that's hard to justify.
For this reason, resume all runtime-suspended PCI devices and all
devices in the ACPI PM domains before creating a snapshot image of
system memory during hibernation.
Fixes: 05087360fd7a (ACPI / PM: Take SMART_SUSPEND driver flag into account) Fixes: c4b65157aeef (PCI / PM: Take SMART_SUSPEND driver flag into account) Link: https://lore.kernel.org/linux-acpi/917d4399-2e22-67b1-9d54-808561f9083f@uwyo.edu/T/#maf065fe6e4974f2a9d79f332ab99dfaba635f64c Reported-by: Robert R. Howell <RHowell@uwyo.edu> Tested-by: Robert R. Howell <RHowell@uwyo.edu> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Commit 5eed6f1dff87 ("fork,memcg: fix crash in free_thread_stack on
memcg charge fail") corrected two instances, but there was a third
instance of this bug.
Without setting tsk->stack, if memcg_charge_kernel_stack fails, it'll
execute free_thread_stack() on a dangling pointer.
Enterprise kernels are compiled with VMAP_STACK=y so this isn't
critical, but custom VMAP_STACK=n builds should have some performance
advantage, with the drawback of risking to fail fork because compaction
didn't succeed. So as long as VMAP_STACK=n is a supported option it's
worth fixing it upstream.
Link: http://lkml.kernel.org/r/20190619011450.28048-1-aarcange@redhat.com Fixes: 9b6f7e163cd0 ("mm: rework memcg kernel stack accounting") Signed-off-by: Andrea Arcangeli <aarcange@redhat.com> Reviewed-by: Rik van Riel <riel@surriel.com> Acked-by: Roman Gushchin <guro@fb.com> Acked-by: Michal Hocko <mhocko@suse.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The RELAX field of the OCOTP block is turning out as a zero on i.MX8MM.
This messes up the subsequent re-load of the fuse shadow registers.
After some discussion with people @ NXP its clear we have missed a trick
here in Linux.
The OCOTP fuse programming time has a physical minimum 'burn time' that is
not related to the ipg_clk.
We need to define the RELAX, STROBE_READ and STROBE_PROG fields in terms of
desired timings to allow for the burn-in to safely complete. Right now only
the RELAX field is calculated in terms of an absolute time and we are
ending up with a value of zero.
This patch inherits the u-boot timings for the OCOTP_TIMING calculation on
the i.MX6 and i.MX8. Those timings are known to work and critically specify
values such as STROBE_PROG as a minimum timing.
When we perform an inexact match on FIB nodes via fib6_locate_1(), longer
prefixes will be preferred to shorter ones. However, it might happen that
a node, with higher fn_bit value than some other, has no valid routing
information.
In this case, we'll pick that node, but it will be discarded by the check
on RTN_RTINFO in fib6_locate(), and we might miss nodes with valid routing
information but with lower fn_bit value.
This is apparent when a routing exception is created for a default route:
# ip -6 route list
fc00:1::/64 dev veth_A-R1 proto kernel metric 256 pref medium
fc00:2::/64 dev veth_A-R2 proto kernel metric 256 pref medium
fc00:4::1 via fc00:2::2 dev veth_A-R2 metric 1024 pref medium
fe80::/64 dev veth_A-R1 proto kernel metric 256 pref medium
fe80::/64 dev veth_A-R2 proto kernel metric 256 pref medium
default via fc00:1::2 dev veth_A-R1 metric 1024 pref medium
# ip -6 route list cache
fc00:4::1 via fc00:2::2 dev veth_A-R2 metric 1024 expires 593sec mtu 1500 pref medium
fc00:3::1 via fc00:1::2 dev veth_A-R1 metric 1024 expires 593sec mtu 1500 pref medium
# ip -6 route flush cache # node for default route is discarded
Failed to send flush request: No such process
# ip -6 route list cache
fc00:3::1 via fc00:1::2 dev veth_A-R1 metric 1024 expires 586sec mtu 1500 pref medium
Check right away if the node has a RTN_RTINFO flag, before replacing the
'prev' pointer, that indicates the longest matching prefix found so far.
Fixes: 38fbeeeeccdb ("ipv6: prepare fib6_locate() for exception table") Signed-off-by: Stefano Brivio <sbrivio@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
SDR50 isn't working anymore because the GPIO regulator
driver is using descriptors since
commit d6cd33ad7102 ("regulator: gpio: Convert to use descriptors")
which in turn causes the system to use the polarity of the
GPIOs (as specified in the DT) for selecting the states,
but the polarity specified in the DT is wrong.
This patch fixes the regulator DT definition, and that fixes
SDR50.
The HiperSockets-based transport path in af_iucv is still too closely
entangled with qeth.
With commit a647a02512ca ("s390/qeth: speed-up L3 IQD xmit"), the
relevant xmit code in qeth has begun to use skb_cow_head(). So to avoid
unnecessary skb head expansions, af_iucv must learn to
1) respect dev->needed_headroom when allocating skbs, and
2) drop the header reference before cloning the skb.
While at it, also stop hard-coding the LL-header creation stage and just
use the appropriate helper.
Fixes: a647a02512ca ("s390/qeth: speed-up L3 IQD xmit") Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The call to sc_buffer_alloc currently returns NULL (no buffer) or
a buffer descriptor.
There is a third case when the port is down. Currently that
returns NULL and this prevents the caller from properly handling the
sc_buffer_alloc() failure. A verbs code link test after the call is
racy so the indication needs to come from the state check inside the allocation
routine to be valid.
Fix by encoding the ECOMM failure like SDMA. IS_ERR_OR_NULL() tests
are added at all call sites. For verbs send, this needs to treat any
error by returning a completion without any MMIO copy.
Fixes: 7724105686e7 ("IB/hfi1: add driver files") Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
We are not destroying the sysfs attribute groupe we registered during
the probe function which will make subsequent probe calls to that
driver fail. Correct that with adding a remove function which only
removes those attributes since the reference counting on clocks did its
job already.
Fixes: 415060b21f31 ("phy: usb: phy-brcm-usb: Add ability to force DRD mode to host or device") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
A request is zeroed in safexcel_ahash_exit_inv(). This request total
size is EIP197_AHASH_REQ_SIZE while the memset zeroing it uses
sizeof(struct ahash_request), which happens to be less than
EIP197_AHASH_REQ_SIZE. This patch fixes it.
Fixes: f6beaea30487 ("crypto: inside-secure - authenc(hmac(sha256), cbc(aes)) support") Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
To avoid this issue set sock->sk after sk_prot->close.
My grepping and testing did not discover any code which
would depend on the current behaviour.
Fixes: c46234ebb4d1 ("tls: RX path for ktls") Reported-by: David Beckett <david.beckett@netronome.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This driver is working well in 'simple cases', but as soon as
more exotic SG lists are provided (dst different from src,
auth part not in a single SG fragment, ...) there are
wrong results, overruns, etc ...
This patch cleans up the AEAD processing by:
- Simplifying the location of 'out of line' ICV
- Never using 'out of line' ICV on encryp
- Always using 'out of line' ICV on decrypt
- Forcing the generation of a SG table on decrypt
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr> Fixes: aeb4c132f33d ("crypto: talitos - Convert to new AEAD interface") Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When hclge_bind_ring_with_vector() fails,
hclge_map_unmap_ring_to_vf_vector() returns the error
directly, so nobody will free the memory allocated by
hclge_get_ring_chain_from_mbx().
So hclge_free_vector_ring_chain() should be called no matter
hclge_bind_ring_with_vector() fails or not.
Fixes: 84e095d64ed9 ("net: hns3: Change PF to add ring-vect binding & resetQ to mailbox") Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
- Fixes a rx data error when data length < 8 bits and parity is enabled.
RDR register MSB is used for parity bit reception.
- Adds a mask to ignore MSB when data is get from RDR.
Fixes: 3489187204eb ("serial: stm32: adding dma support") Signed-off-by: Erwan Le Ray <erwan.leray@st.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
STM32 supports either:
- 8 and 9 bits word length (including parity bit) for stm32f4 compatible
devices
- 7, 8 and 9 bits word length (including parity bit) for stm32f7 and
stm32h7 compatible devices.
As a consequence STM32 supports the following termios configurations:
- CS7 with parity bit, and CS8 (with or without parity bit) for stm32f4
compatible devices.
- CS6 with parity bit, CS7 and CS8 (with or without parity bit) for
stm32f7 and stm32h7 compatible devices.
This patch is fixing word length by configuring correctly the SoC with
supported configurations.
Fixes: ada8618ff3bf ("serial: stm32: adding support for stm32f7") Signed-off-by: Erwan Le Ray <erwan.leray@st.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The documentation says there is an SSEN bit on mpll0 but, after testing
it, no spread spectrum function appears to be enabled by this bit on any
of the MPLLs.
When __afs_break_callback() clears the CB_PROMISED flag, it increments
vnode->cb_break to trigger a future refetch of the status and callback -
however it also calls afs_clear_permits(), which also increments
vnode->cb_break.
Fix this by removing the increment from afs_clear_permits().
Whilst we're at it, fix the conditional call to afs_put_permits() as the
function checks to see if the argument is NULL, so the check is redundant.
__afs_break_callback() holds vnode->lock around its call of
afs_lock_may_be_available() - which also takes that lock.
Fix this by not taking the lock in __afs_break_callback().
Also, there's no point checking the granted_locks and pending_locks queues;
it's sufficient to check lock_state, so move that check out of
afs_lock_may_be_available() into __afs_break_callback() to replace the
queue checks.
Currently IRQF_SHARED type interrupt line is allocated, but it
is not appropriate, as the interrupt line isn't shared between
different devices, instead IRQF_ONESHOT is the proper type.
By changing interrupt type to IRQF_ONESHOT, now irq handler is
no longer needed, as clear of interrupt status can be done in
threaded interrupt context.
Because IRQF_ONESHOT type interrupt line is kept disabled until
the threaded handler has been run, so there is no need to protect
read/write of REG_GEN3_IRQSTR with lock.
Fixes: 7d4b269776ec6 ("enable hardware interrupts for trip points") Signed-off-by: Jiada Wang <jiada_wang@mentor.com> Reviewed-by: Simon Horman <horms+renesas@verge.net.au> Tested-by: Simon Horman <horms+renesas@verge.net.au> Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Eduardo Valentin <edubezval@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
NFP shift instruction has something special. If shift direction is left
then shift amount of 1 to 31 is specified as 32 minus the amount to shift.
But no need to do this for indirect shift which has shift amount be 0. Even
after we do this subtraction, shift amount 0 will be turned into 32 which
will eventually be encoded the same as 0 because only low 5 bits are
encoded, but shift amount be 32 will fail the FIELD_PREP check done later
on shift mask (0x1f), due to 32 is out of mask range. Such error has been
observed when compiling nfp/bpf/jit.c using gcc 8.3 + O3.
This issue has started when indirect shift support added after which the
incoming shift amount to __emit_shf could be 0, therefore it is at that
time shift amount adjustment inside __emit_shf should have been tightened.
Fixes: 991f5b3651f6 ("nfp: bpf: support logic indirect shifts (BPF_[L|R]SH | BPF_X)") Reported-by: Oleksandr Natalenko <oleksandr@natalenko.name> Reported-by: Pablo Cascón <pablo.cascon@netronome.com Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com> Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Jiong Wang <jiong.wang@netronome.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The build of aica sound driver has been broken since the timer API
conversion and some code rewrite. This patch fixes the breakage by
using the common substream field, as well as a bit cleaning up wrt the
timer handling in the code.
Fixes: d522bb6a105f ("ALSA: sh: aica: Convert timers to use timer_setup()") Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
mdev_remove_sysfs_files() should follow exact mirror sequence of a
create, similar to what is followed in error unwinding path of
mdev_create_sysfs_files().
The trace_hardirqs_on() sets current->hardirqs_enabled and from here
the lockdep assumes interrupts are enabled although they are remain
disabled until the context switches to the guest. Consequent
srcu_read_lock() checks the flags in rcu_lock_acquire(), observes
disabled interrupts and prints a warning (see below).
This moves trace_hardirqs_on/off closer to __kvmppc_vcore_entry to
prevent lockdep from being confused.
The test "if (!cmd)" is not useful because it is guaranteed that cmd !=
NULL. Instead of testing the cmd pointer, rely on the tag to decide
whether or not command allocation failed.
Cc: Himanshu Madhani <hmadhani@marvell.com> Cc: Giridhar Malavali <gmalavali@marvell.com> Fixes: 33e799775593 ("qla2xxx: Add support for QFull throttling and Term Exchange retry") # v3.18. Signed-off-by: Bart Van Assche <bvanassche@acm.org> Acked-by: Himanshu Madhani <hmadhani@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Further fix the file locking in the afs filesystem client in a number of
ways, including:
(1) Don't submit the operation to obtain a lock from the server in a work
queue context, but rather do it in the process context of whoever
issued the requesting system call.
(2) The owner of the file_lock struct at the front of the pending_locks
queue now owns right to talk to the server.
(3) Write locks can be instantly granted if they don't overlap with any
other locks *and* we have a write lock on the server.
(4) In the event of an authentication/permission error, all other matching
pending locks requests are also immediately aborted.
(5) Properly use VFS core locks_lock_file_wait() to distribute the server
lock amongst local client locks, including waiting for the lock to
become available.
With the version of sqlite3 that I have, this should fail consistently with
EAGAIN, whether or not the program is straced (which introduces some delays
between lock syscalls).
Fixes: 0fafdc9f888b ("afs: Fix file locking") Reported-by: Jonathan Billings <jsbillin@umich.edu> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Fix AFS file locking to allow fine grained locks as some applications, such
as firefox, won't work if they can't take such locks on certain state files
- thereby preventing the use of kAFS to distribute a home directory.
Note that this cannot be made completely functional as the protocol only
has provision for whole-file locks, so there exists the possibility of a
process deadlocking itself by getting a partial read-lock on a file first
and then trying to get a non-overlapping write-lock - but we got the
server's read lock with the first lock, so we're now stuck.
OpenAFS solves this by just granting any partial-range lock directly
without consulting the server - and hoping there's no remote collision. I
want to implement that in a separate patch and it requires a bit more
thought.
Fixes: 8d6c554126b8 ("AFS: implement file locking") Reported-by: Jonathan Billings <jsbillings@jsbillings.org> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The register bitmask to power on/off the VPU memories was incorectly set
to 0x2 instead of 0x3. While still working, let's use the recommended
vendor value instead.
Fixes: 75fcb5ca4b46 ("soc: amlogic: add Meson GX VPU Domains driver") Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
With commit dfa46c50f65b ("ACPI / button: Fix an issue in
button.lid_init_state=ignore mode"), the lid device is considered to be
not compliant to SW_LID if the Lid state is unchanged when updating it.
This is not wrong, but we overlooked the resume case, where Lid state is
updated unconditionally in the button driver .resume() callback. And this
results in warning message "ACPI: button: The lid device is not compliant
to SW_LID." after resume, if the machine is suspended with Lid opened and
then resumed with Lid opened.
Fix this by flushing the cached lid state before updating the Lid device
in .resume() callback.
Fixes: dfa46c50f65b ("ACPI / button: Fix an issue in button.lid_init_state=ignore mode") Reported-and-tested-by: Zhao Lijian <lijian.zhao@intel.com> Signed-off-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
check_stack_access() that prints verbose log is used in
adjust_ptr_min_max_vals() that prints its own verbose log and now they
stick together, e.g.:
variable stack access var_off=(0xfffffffffffffff0; 0x4) off=-16
size=1R2 stack pointer arithmetic goes out of range, prohibited for
!root
Add missing newline so that log is more readable:
variable stack access var_off=(0xfffffffffffffff0; 0x4) off=-16 size=1
R2 stack pointer arithmetic goes out of range, prohibited for !root
Fixes: f1174f77b50c ("bpf/verifier: rework value tracking") Signed-off-by: Andrey Ignatov <rdna@fb.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The IRQ mapping was changed to not being created in the rtc-mt6397
driver, so the irq_dispose_mapping is no longer needed.
Also the dev_id passed to free_irq should be the same as the last
argument passed to request_threaded_irq.
This prevents a "Trying to free already-free IRQ 274" warning when
unbinding the driver.
If we return early before ddata->clocks have been allocated we will get a
NULL pointer dereference in sysc_unprepare(). Let's fix this by returning
early when no clocks are allocated.
Fixes: 0eecc636e5a2 ("bus: ti-sysc: Add minimal TI sysc interconnect target driver") Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Commit 1848f3f44444 ("ARM: dts: sun9i: Remove GPIO pinctrl nodes to avoid
warnings") was wrong on the optimus, and instead of droping the
pinctrl-names property, it dropped the regulator-name one.
Obviously, that wasn't what was intended. Reinstate regulator-name and drop
pinctrl-names.
Commit d02752149759 ("ARM: dts: sun8i-a23-a33: Move NAND controller device
node to sort by address") moved the NAND controller node around, but
dropped the default muxing in the process.
Reintroduce it.
Fixes: d02752149759 ("ARM: dts: sun8i-a23-a33: Move NAND controller device node to sort by address") Acked-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
These really should have been there from the beginning, but we never
noticed because there was enough slack in the RPC request for the extra
bytes. Chuck's recent patch to use au_cslack and au_rslack to compute
buffer size shrunk the buffer enough that this was now a problem for
SEEK operations on my test client.
Intel IOMMU could be turned off with intel_iommu=off. If Intel
IOMMU is off, the intel_iommu struct will not be initialized.
When device drivers call intel_svm_bind_mm(), the NULL pointer
reference will happen there.
Add dmar_disabled check to avoid NULL pointer reference.
Cc: Ashok Raj <ashok.raj@intel.com> Cc: Jacob Pan <jacob.jun.pan@linux.intel.com> Reported-by: Dave Jiang <dave.jiang@intel.com> Fixes: 2f26e0a9c9860 ("iommu/vt-d: Add basic SVM PASID support") Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com> Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When a child event is allocated in the inherit_event() path, the VMA
based filter offsets are not copied from the parent, even though the
address space mapping of the new task remains the same, which leads to
no trace for the new task until exec.
Reported-by: Mansour Alharthi <malharthi9@gatech.edu> Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Tested-by: Mathieu Poirier <mathieu.poirier@linaro.org> Acked-by: Peter Zijlstra <peterz@infradead.org> Cc: Jiri Olsa <jolsa@redhat.com> Fixes: 375637bc5249 ("perf/core: Introduce address range filtering") Link: http://lkml.kernel.org/r/20190215115655.63469-2-alexander.shishkin@linux.intel.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When a DSA port is added to a bridge and brought up, the resulting STP
state programmed into the hardware depends on the order that these
operations are performed. However, the Linux bridge code believes that
the port is in disabled mode.
If the DSA port is first added to a bridge and then brought up, it will
be in blocking mode. If it is brought up and then added to the bridge,
it will be in disabled mode.
This difference is caused by DSA always setting the STP mode in
dsa_port_enable() whether or not this port is part of a bridge. Since
bridge always sets the STP state when the port is added, brought up or
taken down, it is unnecessary for us to manipulate the STP state.
Apparently, this code was copied from Rocker, and the very next day a
similar fix for Rocker was merged but was not propagated to DSA. See e47172ab7e41 ("rocker: put port in FORWADING state after leaving bridge")
Fixes: b73adef67765 ("net: dsa: integrate with SWITCHDEV for HW bridging") Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The NOUVEAU_GETPARAM_PCI_DEVICE case is missing a break statement and falls
through to the following NOUVEAU_GETPARAM_BUS_TYPE case and may end up
re-assigning the getparam->value to an undesired value. Fix this by adding
in the missing break.
Detected by CoverityScan, CID#1460507 ("Missing break in switch")
Fixes: 359088d5b8ec ("drm/nouveau: remove trivial cases of nvxx_device() usage") Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The CPU port is special and does not need to obey VLAN restrictions as
far as untagged traffic goes, also, having the CPU port be part of a
particular PVID is against the idea of keeping it tagged in all VLANs.
Fixes: ca8931948344 ("net: dsa: b53: Keep CPU port as tagged in all VLANs") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
VLAN filtering can be built into the kernel, and also dynamically turned
on/off through the bridge master device. Allow re-configuring the switch
appropriately to account for that by deciding whether VLAN table
(v_table) misses should lead to a drop or forward.
Fixes: a2482d2ce349 ("net: dsa: b53: Plug in VLAN support") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
We were not consistent in how the default VID of a given port was
defined, b53_br_leave() would make sure the VLAN ID would be either 0/1
depending on the switch generation, but b53_configure_vlan(), which is
the default configuration would unconditionally set it to 1. The correct
value is 1 for 5325/5365 series and 0 otherwise. To avoid repeating that
mistake ever again, introduce a helper function: b53_default_pvid() to
factor that out.
Fixes: 967dd82ffc52 ("net: dsa: b53: Add support for Broadcom RoboSwitch") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The NAND controller device node was inserted into the wrong position,
probably due to a rebase or merge, as the file's structure does not
provide enough context for git to accurately match the previous device
node block.
The current code returns the number of all queues that can be used and
the number of queues that have been allocated, which is incorrect.
What should be returned is the number of queues allocated for each enabled
TC and the number of queues that can be allocated.
This patch fixes it.
Fixes: 849e46077689 ("net: hns3: add ethtool_ops.get_channels support for VF") Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The current code returns the number of all queues that can be used and
the number of queues that have been allocated, which is incorrect.
What should be returned is the number of queues allocated for each enabled
TC and the number of queues that can be allocated.
This patch fixes it.
Fixes: 482d2e9c1cc7 ("net: hns3: add support to query tqps number") Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Commit 5eed6f1dff87 ("fork,memcg: fix crash in free_thread_stack on
memcg charge fail") fixes a crash caused due to failed memcg charge of
the kernel stack. However the fix misses the cached_stacks case which
this patch fixes. So, the same crash can happen if the memcg charge of
a cached stack is failed.
Link: http://lkml.kernel.org/r/20190102180145.57406-1-shakeelb@google.com Fixes: 5eed6f1dff87 ("fork,memcg: fix crash in free_thread_stack on memcg charge fail") Signed-off-by: Shakeel Butt <shakeelb@google.com> Acked-by: Michal Hocko <mhocko@suse.com> Acked-by: Rik van Riel <riel@surriel.com> Cc: Rik van Riel <riel@surriel.com> Cc: Roman Gushchin <guro@fb.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Tejun Heo <tj@kernel.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The ->nr_signal is the supposed to be the number of elements in the
->signal array. There was one place where it was 5 but it was supposed
to be 4. That looks like a copy and paste bug. There were also two
checks that were off by one.
Fixes: 9e2c2e273012 ("drm/etnaviv: add infrastructure to query perf counter") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com> Tested-by: Christian Gmeiner <christian.gmeiner@gmail.com> Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
projects / mirror_ubuntu-bionic-kernel.git / log