The expect_rx_by call timeout is supposed to be set when a call is started
to indicate that we need to receive a packet by that point. This is
currently put back every time we receive a packet, but it isn't started
when we first send a packet. Without this, the call may wait forever if
the server doesn't deign to reply.
Fix this by setting the timeout upon a successful UDP sendmsg call for the
first DATA packet. The timeout is initiated only for initial transmission
and not for subsequent retries as we don't want the retry mechanism to
extend the timeout indefinitely.
Fixes: a158bdd3247b ("rxrpc: Fix call timeouts") Reported-by: Marc Dionne <marc.dionne@auristor.com> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The data buffer allocated on the stack can't be DMA'ed, ib_dma_map_page will
return an invalid DMA address for a buffer on stack. Even worse, this
incorrect address can't be detected by ib_dma_mapping_error. Sending data
from this address to hardware will not fail, but the remote peer will get
junk data.
Fix this by allocating the request on the heap in smb3_validate_negotiate.
Changes in v2:
Removed duplicated code on freeing buffers on function exit.
(Thanks to Parav Pandit <parav@mellanox.com>)
Fixed typo in the patch title.
Changes in v3:
Added "Fixes" to the patch.
Changed several sizeof() to use *pointer in place of struct.
Changes in v4:
Added detailed comments on the failure through RDMA.
Allocate request buffer using GPF_NOFS.
Fixed possible memory leak.
Changes in v5:
Removed variable ret for checking return value.
Changed to use pneg_inbuf->Dialects[0] to calculate unused space in pneg_inbuf.
Fixes: ff1c038addc4 ("Check SMB3 dialects against downgrade attacks") Signed-off-by: Long Li <longli@microsoft.com> Signed-off-by: Steve French <stfrench@microsoft.com> Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com> Reviewed-by: Tom Talpey <ttalpey@microsoft.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The 0457:10fb touchscreen found on the Toshiba Click Mini L9W-B needs
to have a report-decriptors command send to it on resume in order for
the touchscreen to start generating events again on resume.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The build is failing with CONFIG_NUMA=n and some compiler versions:
arch/powerpc/platforms/pseries/hotplug-cpu.o: In function `dlpar_online_cpu':
hotplug-cpu.c:(.text+0x12c): undefined reference to `timed_topology_update'
arch/powerpc/platforms/pseries/hotplug-cpu.o: In function `dlpar_cpu_remove':
hotplug-cpu.c:(.text+0x400): undefined reference to `timed_topology_update'
Fix it by moving the empty version of timed_topology_update() into the
existing #ifdef block, which has the right guard of SPLPAR && NUMA.
Fixes: cee5405da402 ("powerpc/hotplug: Improve responsiveness of hotplug change") Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Currently only nvme_ctrl will take a reference counter of
nvme_subsystem, nvme_ns_head also needs it. Otherwise
nvme_free_ns_head will access the nvme_subsystem.ns_ida
which has been freed by __nvme_release_subsystem after all the
reference of nvme_subsystem have been released by nvme_free_ctrl.
This could cause memory corruption.
BUG: KASAN: use-after-free in radix_tree_next_chunk+0x9f/0x4b0
Read of size 8 at addr ffff88036494d2e8 by task fio/1815
In the cleanup, I didn't notice that we needed to dereference the
connector for the bus_format. Fix the regression by looking up the
first (and only) connector attached to us, and assume that its
bus_format is what we want. Some day it would be good to have that
part of display_info attached to the bridge, instead.
v2: Fix stray whitespace change
Signed-off-by: Eric Anholt <eric@anholt.net> Fixes: 7b1298e05310 ("drm/vc4: Switch DPI to using the panel-bridge helper.") Link: https://patchwork.freedesktop.org/patch/msgid/20180309233256.1667-1-eric@anholt.net Reviewed-by: Sean Paul <seanpaul@chromium.org> Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Sean Paul <seanpaul@chromium.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Since commit d677a4d60193 ("Makefile: support flag
-fsanitizer-coverage=trace-cmp"), you miss to build the SANCOV
plugin under some circumstances.
CONFIG_KCOV=y
CONFIG_KCOV_ENABLE_COMPARISONS=y
Your compiler does not support -fsanitize-coverage=trace-pc
Your compiler does not support -fsanitize-coverage=trace-cmp
Under this condition, $(CFLAGS_KCOV) is not empty but contains a
space, so the following ifeq-conditional is false.
ifeq ($(CFLAGS_KCOV),)
Then, scripts/Makefile.gcc-plugins misses to add sancov_plugin.so to
gcc-plugin-y while the SANCOV plugin is necessary as an alternative
means.
Fixes: d677a4d60193 ("Makefile: support flag -fsanitizer-coverage=trace-cmp") Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Acked-by: Kees Cook <keescook@chromium.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Commit 9ef09e35e521 ("bpf: fix possible spectre-v1 in find_and_alloc_map()")
converted find_and_alloc_map() over to use array_index_nospec() to sanitize
map type that user space passes on map creation, and this patch does an
analogous conversion for progs in find_prog_type() as it's also passed from
user space when loading progs as attr->prog_type.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Cc: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
In case of interlace mode video processor registers and mixer config
register must be check to ensure internal state is in sync with shadow
registers.
This patch fixes page-faults in interlaced mode.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Inki Dae <inki.dae@samsung.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
It's possible for userspace to control attr->map_type. Sanitize it when
using it as an array index to prevent an out-of-bounds value being used
under speculation.
Found by smatch.
Signed-off-by: Mark Rutland <mark.rutland@arm.com> Cc: Alexei Starovoitov <ast@kernel.org> Cc: Dan Carpenter <dan.carpenter@oracle.com> Cc: Daniel Borkmann <daniel@iogearbox.net> Cc: Peter Zijlstra <peterz@infradead.org> Cc: netdev@vger.kernel.org Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Jakub Kicinski [Fri, 12 Jan 2018 04:29:03 +0000 (20:29 -0800)]
bpf: add map_alloc_check callback
BugLink: http://bugs.launchpad.net/bugs/1794889
.map_alloc callbacks contain a number of checks validating user-
-provided map attributes against constraints of a particular map
type. For offloaded maps we will need to check map attributes
without actually allocating any memory on the host. Add a new
callback for validating attributes before any memory is allocated.
This callback can be selectively implemented by map types for
sharing code with offloads, or simply to separate the logical
steps of validation and allocation.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
(cherry picked from commit 1110f3a9bcf394c06b81a98206aee9b6860653c8) Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When the kernel was compiled using the UBSAN option,
we saw the following stack trace:
[ 1184.827917] UBSAN: Undefined behaviour in drivers/infiniband/hw/mlx4/mr.c:349:27
[ 1184.828114] signed integer overflow:
[ 1184.828247] -2147483648 - 1 cannot be represented in type 'int'
The problem was caused by calling round_up in procedure
mlx4_ib_umem_calc_optimal_mtt_size (on line 349, as noted in the stack
trace) with the second parameter (1 << block_shift) (which is an int).
The second parameter should have been (1ULL << block_shift) (which
is an unsigned long long).
(1 << block_shift) is treated by the compiler as an int (because 1 is
an integer).
Now, local variable block_shift is initialized to 31.
If block_shift is 31, 1 << block_shift is 1 << 31 = 0x80000000=-214748368.
This is the most negative int value.
Inside the round_up macro, there is a cast applied to ((1 << 31) - 1).
However, this cast is applied AFTER ((1 << 31) - 1) is calculated.
Since (1 << 31) is treated as an int, we get the negative overflow
identified by UBSAN in the process of calculating ((1 << 31) - 1).
The fix is to change (1 << block_shift) to (1ULL << block_shift) on
line 349.
Fixes: 9901abf58368 ("IB/mlx4: Use optimal numbers of MTT entries") Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
If the I2C adapter that the PD controller is attached to
does not support SMBus protocol, the driver needs to handle
block reads separately. The first byte returned in block
read protocol will show the total number of bytes. It needs
to be stripped away.
This is handled separately in the driver only because right
now we have no way of requesting the used protocol with
regmap-i2c. This is in practice a workaround for what is
really a problem in regmap-i2c. The other option would have
been to register custom regmap, or not use regmap at all,
however, since the solution is very simple, I choose to use
it in this case for convenience. It is easy to remove once
we figure out how to handle this kind of cases in
regmap-i2c.
Fixes: 0a4c005bd171 ("usb: typec: driver for TI TPS6598x USB Power Delivery controllers") Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The missing "compatible" entries are needed by drivers/clk/ti/clkctrl.c,
and without them the structures initialized in drivers/clk/ti/clk-814x.c
are not passed to configuration code. The result is a "not found from
clkctrl data" error message, although boot proceeds anyway.
The reason why the compatible is not found is because the board specific
files override the SoC compatible without including it. This did not
cause any issues until with the clkctrl nodes got introduced.
Very lightly tested on a (lurching) AM3874 design that's in the middle
of a kernel upgrade from TI's abandoned 2.6.37 tree.
Also tested on j5eco-evm and hp-t410 to verify the clkctrl clocks are
found.
Fixes: bb30465b5902 ("ARM: dts: dm814x: add clkctrl nodes") Fixes: 80a06c0d8357 ("ARM: dts: dm816x: add clkctrl nodes") Signed-off-by: Graeme Smecher <gsmecher@threespeedlogic.com>
[tony: updated to fix for 8168-evm, updated comments] Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
We can't allow the user to change multipath settings at runtime, as this
will create naming conflicts due to the different naming schemes used
for each mode.
Signed-off-by: Keith Busch <keith.busch@intel.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
It was noticed that the IRTE configured for guest OS kernel
was over-written while the guest was running. As a result,
vt-d Posted Interrupts configured for the guest are not being
delivered directly, and instead bounces off the host. Every
interrupt delivery takes a VM Exit.
It was noticed that the following stack is doing the over-write:
[ 147.463177] modify_irte+0x171/0x1f0
[ 147.463405] intel_ir_set_affinity+0x5c/0x80
[ 147.463641] msi_domain_set_affinity+0x32/0x90
[ 147.463881] irq_do_set_affinity+0x37/0xd0
[ 147.464125] irq_set_affinity_locked+0x9d/0xb0
[ 147.464374] __irq_set_affinity+0x42/0x70
[ 147.464627] write_irq_affinity.isra.5+0xe1/0x110
[ 147.464895] proc_reg_write+0x38/0x70
[ 147.465150] __vfs_write+0x36/0x180
[ 147.465408] ? handle_mm_fault+0xdf/0x200
[ 147.465671] ? _cond_resched+0x15/0x30
[ 147.465936] vfs_write+0xad/0x1a0
[ 147.466204] SyS_write+0x52/0xc0
[ 147.466472] do_syscall_64+0x74/0x1a0
[ 147.466744] entry_SYSCALL_64_after_hwframe+0x3d/0xa2
reversing the sense of force check in intel_ir_reconfigure_irte()
restores proper posted interrupt functionality
Even with the wait-loop fixed, there is a further issue with
kthread_parkme(). Upon hotplug, when we do takedown_cpu(),
smpboot_park_threads() can return before all those threads are in fact
blocked, due to the placement of the complete() in __kthread_parkme().
When that happens, sched_cpu_dying() -> migrate_tasks() can end up
migrating such a still runnable task onto another CPU.
Normally the task will have hit schedule() and gone to sleep by the
time we do kthread_unpark(), which will then do __kthread_bind() to
re-bind the task to the correct CPU.
However, when we loose the initial TASK_PARKED store to the concurrent
wakeup issue described previously, do the complete(), get migrated, it
is possible to either:
- observe kthread_unpark()'s clearing of SHOULD_PARK and terminate
the park and set TASK_RUNNING, or
- __kthread_bind()'s wait_task_inactive() to observe the competing
TASK_RUNNING store.
Either way the WARN() in __kthread_bind() will trigger and fail to
correctly set the CPU affinity.
Fix this by only issuing the complete() when the kthread has scheduled
out. This does away with all the icky 'still running' nonsense.
The alternative is to promote TASK_PARKED to a special state, this
guarantees wait_task_inactive() cannot observe a 'stale' TASK_RUNNING
and we'll end up doing the right thing, but this preserves the whole
icky business of potentially migating the still runnable thing.
Reported-by: Gaurav Kohli <gkohli@codeaurora.org> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When we dropped the custom Linux GPIO translation it resulted that the
IRQ numbers changed slightly as well. Normally this would be fine
because everyone is expected to use controller relative GPIO numbers and
ACPI GpioIo/GpioInt resources. However, there is a certain set of
Intel_Strago based Chromebooks where i8042 keyboard controller IRQ
number is hardcoded be 182 (this is corrected with newer coreboot but
the older ones still have the hardcoded Linux IRQ number). Because of
this hardcoded IRQ number keyboard on those systems accidentally broke
again.
Fix this by iteratively associating IRQ descriptors to the chip irqdomain
so that there are no gaps on those systems. Other systems are not
affected.
Fixes: 03c4749dd6c7 ("gpio / ACPI: Drop unnecessary ACPI GPIO to Linux GPIO translation") Link: https://bugzilla.kernel.org/show_bug.cgi?id=199463 Reported-by: Sultan Alsawaf <sultanxda@gmail.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Previously, if a method contained mandatory attributes in a namespace
that wasn't given by the user, these attributes weren't validated.
Fixing this by iterating over all specification namespaces.
Currently, KVM flushes the TLB after a change to the APIC access page
address or the APIC mode when EPT mode is enabled. However, even in
shadow paging mode, a TLB flush is needed if VPIDs are being used, as
specified in the Intel SDM Section 29.4.5.
So replace vmx_flush_tlb_ept_only() with vmx_flush_tlb(), which will
flush if either EPT or VPIDs are in use.
Signed-off-by: Junaid Shahid <junaids@google.com> Reviewed-by: Jim Mattson <jmattson@google.com> Signed-off-by: Radim Krčmář <rkrcmar@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When clk_prepare_enable fails for the axi_clk, the mg_clk isn't properly
cleaned up. Add another jump label to handle that case, and make sure we
jump to it in the later error cases.
Fixes: 4792ea04bcd0 ("net: mvpp2: Fix clock resource by adding an optional bus clock") Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
For very very old generation of the management FW Ethernet port
information table may theoretically not be available. This in
turn will cause the nfp_port structures to not be allocated.
Make sure we don't crash the kernel when there is no eth_tbl:
Found while working with broken/development version of management FW.
Fixes: a5950182c00e ("nfp: map mac_stats and vf_cfg BARs") Fixes: 93da7d9660ee ("nfp: provide nfp_port to of nfp_net_get_mac_addr()") Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
For LD20, the bit 5 of the offset 0x200c turned out to be a USB3
reset. The hardware document says it is the GIO reset despite LD20
has no GIO bus, confusingly.
Also, fix confusing comments for PXs3.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
arch/powerpc/kvm/emulate_loadstore.o: In function `kvmppc_check_altivec_disabled':
arch/powerpc/kvm/emulate_loadstore.c: undefined reference to `.kvmppc_core_queue_vec_unavail'
Fixes: 09f984961c137c4b ("KVM: PPC: Book3S: Add MMIO emulation for VMX instructions") Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Commit 2a5418a13fcf ("bpf: improve dead code sanitizing") replaced dead
code with a series of ja-1 instructions, for safety. That made JIT
compilation much more complex for some BPF programs. One instance of such
programs is, for example:
bool flag = false
...
/* A bunch of other code */
...
if (flag)
do_something()
In some cases llvm is not able to remove at compile time the code for
do_something(), so the generated BPF program ends up with a large amount
of dead instructions. In one specific real life example, there are two
series of ~500 and ~1000 dead instructions in the program. When the
verifier replaces them with a series of ja-1 instructions, it causes an
interesting behavior at JIT time.
During the first pass, since all the instructions are estimated at 64
bytes, the ja-1 instructions end up being translated as 5 bytes JMP
instructions (0xE9), since the jump offsets become increasingly large (>
127) as each instruction gets discovered to be 5 bytes instead of the
estimated 64.
Starting from the second pass, the first N instructions of the ja-1
sequence get translated into 2 bytes JMPs (0xEB) because the jump offsets
become <= 127 this time. In particular, N is defined as roughly 127 / (5
- 2) ~= 42. So, each further pass will make the subsequent N JMP
instructions shrink from 5 to 2 bytes, making the image shrink every time.
This means that in order to have the entire program converge, there need
to be, in the real example above, at least ~1000 / 42 ~= 24 passes just
for translating the dead code. If we add this number to the passes needed
to translate the other non dead code, it brings such program to 40+
passes, and JIT doesn't complete. Ultimately the userspace loader fails
because such BPF program was supposed to be part of a prog array owner
being JITed.
While it is certainly possible to try to refactor such programs to help
the compiler remove dead code, the behavior is not really intuitive and it
puts further burden on the BPF developer who is not expecting such
behavior. To make things worse, such programs are working just fine in all
the kernel releases prior to the ja-1 fix.
A possible approach to mitigate this behavior consists into noticing that
for ja-1 instructions we don't really need to rely on the estimated size
of the previous and current instructions, we know that a -1 BPF jump
offset can be safely translated into a 0xEB instruction with a jump offset
of -2.
Such fix brings the BPF program in the previous example to complete again
in ~9 passes.
Fixes: 2a5418a13fcf ("bpf: improve dead code sanitizing") Signed-off-by: Gianluca Borello <g.borello@gmail.com> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The reason is that current implementation doesn't check PMU name of a
event when adding its alias into the alias list for core PMU. The
uncore event aliases are mistakenly added.
This bug was introduced in:
commit 14b22ae028de ("perf pmu: Add helper function is_pmu_core to
detect PMU CORE devices")
Checking the PMU name for all PMUs on X86 and other architectures except
ARM.
There is no behavior change for ARM.
Signed-off-by: Kan Liang <kan.liang@linux.intel.com> Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Agustin Vega-Frias <agustinv@codeaurora.org> Cc: Andi Kleen <ak@linux.intel.com> Cc: Ganapatrao Kulkarni <ganapatrao.kulkarni@cavium.com> Cc: Jin Yao <yao.jin@linux.intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Shaokun Zhang <zhangshaokun@hisilicon.com> Cc: Will Deacon <will.deacon@arm.com> Fixes: 14b22ae028de ("perf pmu: Add helper function is_pmu_core to detect PMU CORE devices") Link: http://lkml.kernel.org/r/1524594014-79243-1-git-send-email-kan.liang@linux.intel.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Our arm64_skip_faulting_instruction() helper advances the userspace
singlestep state machine, but this is also called by the kernel BRK
handler, as used for WARN*().
Thus, if we happen to hit a WARN*() while the user singlestep state
machine is in the active-no-pending state, we'll advance to the
active-pending state without having executed a user instruction, and
will take a step exception earlier than expected when we return to
userspace.
Let's fix this by only advancing the state machine when skipping a user
instruction.
Signed-off-by: Mark Rutland <mark.rutland@arm.com> Cc: Andrey Konovalov <andreyknvl@google.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Will Deacon <will.deacon@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Debian toolcahin defaults to PIE, and I guess that will also be the case
of most distributions. This causes the following build failure:
AS arch/riscv/kernel/vdso/getcpu.o
AS arch/riscv/kernel/vdso/flush_icache.o
VDSOLD arch/riscv/kernel/vdso/vdso.so.dbg
OBJCOPY arch/riscv/kernel/vdso/vdso.so
AS arch/riscv/kernel/vdso/vdso.o
VDSOLD arch/riscv/kernel/vdso/vdso-dummy.o
LD arch/riscv/kernel/vdso/vdso-syms.o
riscv64-linux-gnu-ld: attempted static link of dynamic object `arch/riscv/kernel/vdso/vdso-dummy.o'
make[2]: *** [arch/riscv/kernel/vdso/Makefile:43: arch/riscv/kernel/vdso/vdso-syms.o] Error 1
make[1]: *** [scripts/Makefile.build:575: arch/riscv/kernel/vdso] Error 2
make: *** [Makefile:1018: arch/riscv/kernel] Error 2
While the root Makefile correctly passes "-fno-PIE" to build individual
object files, the RISC-V kernel also builds vdso-dummy.o as an
executable, which is therefore linked as PIE. Fix that by updating this
specific link rule to also include "-no-pie".
The property of the legacy mode for the eMMC PHY turned out to
be wrong. Some eMMC devices are unstable due to the set-up/hold
timing violation. Correct the delay value.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Dan Carpenter had pointed this out a while ago, but the code around
this had changed so wasn't causing any problems since that field
was not used in this error path.
Still, it is cleaner to always initialize this field, so changing
the error path to set it.
Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com> CC: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Steve French <smfrench@gmail.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
At least on one Dell system the PNP motherboard resources device
includes resources used by WDAT table. Since PNP gets initialized before
WDAT it results following error and no watchdog:
Now, the PNP system driver is already accustomed with the situation that
it cannot reserve all those motherboard resources because drivers using
those might have reserved them already. In addition putting WDAT table
resources under motherboard resources device makes sense in general.
Fix this by initializing WDAT right before PNP. This allows WDAT to
reserve all its resources and still keeps PNP system driver happy.
Reported-by: Shubhrata.Priyadarsh@dell.com Reported-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Acked-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Submitting a cmd IO request (usually on the WRITE device, but for IDX
also on the READ device) is currently done with ccw_device_start()
and a manual timeout in the caller.
On timeout, the caller cleans up the related resources (eg. IO buffer).
But 1) the IO might still be active and utilize those resources, and
2) when the IO completes, qeth_irq() will attempt to clean up the
same resources again.
Instead of introducing additional resource locking, switch to
ccw_device_start_timeout() to ensure IO termination after timeout, and
let the IRQ handler alone deal with cleaning up after a request.
This also removes a stray write->irq_pending reset from
clear_ipacmd_list(). The routine doesn't terminate any pending IO on
the WRITE device, so this should be handled properly via IO timeout
in the IRQ handler.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
AFS server records get removed from the net->fs_servers tree when
they're deleted, but not from the net->fs_addresses{4,6} lists, which
can lead to an oops in afs_find_server() when a server record has been
removed, for instance during rmmod.
Fix this by deleting the record from the by-address lists before posting
it for RCU destruction.
The reason this hasn't been noticed before is that the fileserver keeps
probing the local cache manager, thereby keeping the service record
alive, so the oops would only happen when a fileserver eventually gets
bored and stops pinging or if the module gets rmmod'd and a call comes
in from the fileserver during the window between the server records
being destroyed and the socket being closed.
The Khadas VIM2 board connects the dwc3 controller to an internal 4-port
USB hub which. Two of these ports are accessible directly soldered to
the board, while the other two are accessible through the 40-pin "GPIO"
header.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The LibreTech CC ("Le Potato") board provides four USB connectors.
These are provided by a hub which is connected to the SoC's USB
controller.
Enable the SoC's USB controller to make the USB ports usable. Also turn
on the HDMI_5V regulator when powering on the PHY because (even though
it's not shown in the schematics) HDMI_5V also supplies the USB VBUS.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
All S905D (GXL) and S912 (GXM) reference boards (namely these are
P230, P231, Q200 and Q201) provide USB connectors.
This enables the USB controller on these boards to make the USB ports
actually usable.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
All boards based on the P212 reference design (the P212 reference board
itself and the Khadas VIM) have USB connectors (in case of the Khadas
VIM the first port is exposed through the USB Type-C connector, the
second port is connected to a 4-port USB hub).
This enables the USB controller on these boards to make the USB ports
actually usable.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The USB configuration on GXM is slightly different than on GXL. The dwc3
controller's internal hub has three USB2 ports (instead of 2 on GXL)
along with a dedicated USB2 PHY for this port. However, it seems that
there are no pins on GXM which would allow connecting the third port to
a physical USB port.
Passing the third PHY is required though, because without it none of the
other USB ports is working (this seems to be a limitation of how the
internal USB hub works, if one PHY is disabled then no USB port works).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
This adds USB host support to the Meson GXL SoC. A dwc3 controller is
used for host-mode, while a dwc2 controller (not added in this patch
because I could not get it working) is used for device-mode only.
The dwc3 controller's internal roothub has two USB2 ports enabled but no
USB3 port. Each of the ports is supplied by a separate PHY. The USB pins
are connected to the SoC's USBHOST_A and USBOTG_B pins.
Due to the way the roothub works internally the USB PHYs are left
enabled. When the dwc3 controller is disabled the PHY is never powered on
so it does not draw any extra power. However, when the dwc3 host
controller is enabled then all PHYs also have to be enabled, otherwise
USB devices will not be detected (regardless of whether they are plugged
into an enabled port or not). This means that only the dwc3 controller
has to be enabled on boards with USB support (instead of requiring all
boards to enable the PHYs additionally with the chance of forgetting to
enable one and breaking all other ports with that as well).
This also adds the USB3 PHY which currently only does some basic
initialization. That however is required because without it high-speed
devices (like USB thumb drives) do not work on some devices (probably
because the bootloader does not configure the USB3 PHY registers).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
In arm64's kasan_init(), we use pfn_to_nid() to find the NUMA node a
span of memory is in, hoping to allocate shadow from the same NUMA node.
However, at this point, the page array has not been initialized, and
thus this is bogus.
Let's fix this by using early_pfn_to_nid(), as other architectures do in
their kasan init code. Note that early_pfn_to_nid acquires the nid from
the memblock array, which we iterate over in kasan_init(), so this
should be fine.
Signed-off-by: Mark Rutland <mark.rutland@arm.com> Fixes: 39d114ddc6822302 ("arm64: add KASAN support") Cc: Will Deacon <will.deacon@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When vgic_prune_ap_list() finds an interrupt that needs to be migrated
to a new VCPU, we should notify this VCPU of the pending interrupt,
since it requires immediate action.
Kick this VCPU once we have added the new IRQ to the list, but only
after dropping the locks.
Reported-by: Stefano Stabellini <sstabellini@kernel.org> Reviewed-by: Christoffer Dall <christoffer.dall@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
If there is no d-cache-size property in the device tree, l1d_size could
be zero. We don't actually expect that to happen, it's only been seen
on mambo (simulator) in some configurations.
A zero-size l1d_size leads to the loop in the asm wrapping around to
2^64-1, and then walking off the end of the fallback area and
eventually causing a page fault which is fatal.
Just default to 64K which is correct on some CPUs, and sane enough to
not cause a crash on others.
Fixes: aa8a5e0062ac9 ('powerpc/64s: Add support for RFI flush of L1-D cache') Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
[mpe: Rewrite comment and change log] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Update 'tsc_offset' on vmentry/vmexit of L2 guests to ensure that it always
captures the TSC_OFFSET of the running guest whether it is the L1 or L2
guest.
Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Radim Krčmář <rkrcmar@redhat.com> Cc: kvm@vger.kernel.org Cc: linux-kernel@vger.kernel.org Reviewed-by: Jim Mattson <jmattson@google.com> Suggested-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: KarimAllah Ahmed <karahmed@amazon.de>
[AMD changes, fix update_ia32_tsc_adjust_msr. - Paolo] Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When attempting to change the driver parameters, such as the MTU
value or number of queues, do not call netdev_notify_peers().
Doing so will deadlock on the rtnl_lock.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
While rcvbuf is properly clamped by tcp_rmem[2], rcvwin
is left to a potentially too big value.
It has no serious effect, since :
1) tcp_grow_window() has very strict checks.
2) window_clamp can be mangled by user space to any value anyway.
tcp_init_buffer_space() and companions use tcp_full_space(),
we use tcp_win_from_space() to avoid reloading sk->sk_rcvbuf
Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Acked-by: Wei Wang <weiwan@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
There is a scenario that can end up with rebuild process failing to
return good content, i.e.
suppose that all disks can be read without problems and if the content
that was read out doesn't match its checksum, currently for raid6
btrfs at most retries twice,
- the 1st retry is to rebuild with all other stripes, it'll eventually
be a raid5 xor rebuild,
- if the 1st fails, the 2nd retry will deliberately fail parity p so
that it will do raid6 style rebuild,
however, the chances are that another non-parity stripe content also
has something corrupted, so that the above retries are not able to
return correct content, and users will think of this as data loss.
More seriouly, if the loss happens on some important internal btree
roots, it could refuse to mount.
This extends btrfs to do more retries and each retry fails only one
stripe. Since raid6 can tolerate 2 disk failures, if there is one
more failure besides the failure on which we're recovering, this can
always work.
The worst case is to retry as many times as the number of raid6 disks,
but given the fact that such a scenario is really rare in practice,
it's still acceptable.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The raid6 corruption is that,
suppose that all disks can be read without problems and if the content
that was read out doesn't match its checksum, currently for raid6
btrfs at most retries twice,
- the 1st retry is to rebuild with all other stripes, it'll eventually
be a raid5 xor rebuild,
- if the 1st fails, the 2nd retry will deliberately fail parity p so
that it will do raid6 style rebuild,
however, the chances are that another non-parity stripe content also
has something corrupted, so that the above retries are not able to
return correct content.
We've fixed normal reads to rebuild raid6 correctly with more retries
in Patch "Btrfs: make raid6 rebuild retry more"[1], this is to fix
scrub to do the exactly same rebuild process.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When a panic() occurs, the kexec code uses smp_send_stop() to stop
the other CPUs, but this results in the CPU register state not being
saved, and gdb is unable to inspect the state of other CPUs.
Commit 0ee59413c967 ("x86/panic: replace smp_send_stop() with kdump
friendly version in panic path") addressed the issue on x86, but
ignored other architectures. Address the issue on ARM by splitting
out the crash stop implementation to crash_smp_send_stop() and
adding the necessary protection.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The hypervisor setup before __enter_kernel destroys the value
sotred in r1. The value needs to be restored just before the jump.
Fixes: 6b52f7bdb888 ("ARM: hyp-stub: Use r1 for the soft-restart address") Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
In commit 639da5ee374b ("ARM: add an extra temp register to the low
level debugging addruart macro") an additional temporary register was
added to the addruart macro, but the decompressor code wasn't updated.
Fixes: 639da5ee374b ("ARM: add an extra temp register to the low level debugging addruart macro") Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When CONFIG_RANDOMIZE_TEXT_OFFSET=y, TEXT_OFFSET is an arbitrary
multiple of PAGE_SIZE in the interval [0, 2MB).
The EFI stub does not account for the potential misalignment of
TEXT_OFFSET relative to EFI_KIMG_ALIGN, and produces a randomized
physical offset which is always a round multiple of EFI_KIMG_ALIGN.
This may result in statically allocated objects whose alignment exceeds
PAGE_SIZE to appear misaligned in memory. This has been observed to
result in spurious stack overflow reports and failure to make use of
the IRQ stacks, and theoretically could result in a number of other
issues.
We can OR in the low bits of TEXT_OFFSET to ensure that we have the
necessary offset (and hence preserve the misalignment of TEXT_OFFSET
relative to EFI_KIMG_ALIGN), so let's do that.
Reported-by: Kim Phillips <kim.phillips@arm.com> Tested-by: Kim Phillips <kim.phillips@arm.com>
[ardb: clarify comment and commit log, drop unneeded parens] Signed-off-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-efi@vger.kernel.org Fixes: 6f26b3671184c36d ("arm64: kaslr: increase randomization granularity") Link: http://lkml.kernel.org/r/20180518140841.9731-2-ard.biesheuvel@linaro.org Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
No other architecture has setup_profiling_timer() in the init section,
thus on parisc we face this section mismatch warning:
Reference from the function devm_device_add_group() to the function .init.text:setup_profiling_timer()
Signed-off-by: Helge Deller <deller@gmx.de> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
6b55c9654fcc ("sched/debug: Move print_cfs_rq() declaration to kernel/sched/sched.h")
the print_cfs_rq() prototype was added to <kernel/sched/sched.h>,
right next to the prototypes for print_cfs_stats(), print_rt_stats()
and print_dl_stats().
Finish this previous commit and also move related prototypes for
print_rt_rq() and print_dl_rq().
Remove existing extern declarations now that they not needed anymore.
Silences the following GCC warning, triggered by W=1:
kernel/sched/debug.c:573:6: warning: no previous prototype for ‘print_rt_rq’ [-Wmissing-prototypes]
kernel/sched/debug.c:603:6: warning: no previous prototype for ‘print_dl_rq’ [-Wmissing-prototypes]
The integer overflow in DIV_ROUND_UP() means "cpp" is UINT_MAX / 8 and
because of how we picked args->width that means cpp < UINT_MAX / 4.
I've fixed it by preventing the integer overflow in DIV_ROUND_UP(). I
removed the check for !cpp because it's not possible after this change.
I also changed all the 0xffffffffU references to U32_MAX.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Link: https://patchwork.freedesktop.org/patch/msgid/20180516140026.GA19340@mwanda Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The filesystem freezing code needs to transfer ownership of a rwsem
embedded in a percpu-rwsem from the task that does the freezing to
another one that does the thawing by calling percpu_rwsem_release()
after freezing and percpu_rwsem_acquire() before thawing.
However, the new rwsem debug code runs afoul with this scheme by warning
that the task that releases the rwsem isn't the one that acquires it,
as reported by Amir Goldstein:
To work properly with the rwsem debug code, we need to annotate that the
rwsem ownership is unknown during the tranfer period until a brave soul
comes forward to acquire the ownership. During that period, optimistic
spinning will be disabled.
Reported-by: Amir Goldstein <amir73il@gmail.com> Tested-by: Amir Goldstein <amir73il@gmail.com> Signed-off-by: Waiman Long <longman@redhat.com> Acked-by: Peter Zijlstra <peterz@infradead.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Davidlohr Bueso <dave@stgolabs.net> Cc: Jan Kara <jack@suse.cz> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Matthew Wilcox <willy@infradead.org> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Theodore Y. Ts'o <tytso@mit.edu> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Will Deacon <will.deacon@arm.com> Cc: linux-fsdevel@vger.kernel.org Link: http://lkml.kernel.org/r/1526420991-21213-3-git-send-email-longman@redhat.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
There are use cases where a rwsem can be acquired by one task, but
released by another task. In thess cases, optimistic spinning may need
to be disabled. One example will be the filesystem freeze/thaw code
where the task that freezes the filesystem will acquire a write lock
on a rwsem and then un-owns it before returning to userspace. Later on,
another task will come along, acquire the ownership, thaw the filesystem
and release the rwsem.
Bit 0 of the owner field was used to designate that it is a reader
owned rwsem. It is now repurposed to mean that the owner of the rwsem
is not known. If only bit 0 is set, the rwsem is reader owned. If bit
0 and other bits are set, it is writer owned with an unknown owner.
One such value for the latter case is (-1L). So we can set owner to 1 for
reader-owned, -1 for writer-owned. The owner is unknown in both cases.
To handle transfer of rwsem ownership, the higher level code should
set the owner field to -1 to indicate a write-locked rwsem with unknown
owner. Optimistic spinning will be disabled in this case.
Once the higher level code figures who the new owner is, it can then
set the owner field accordingly.
Tested-by: Amir Goldstein <amir73il@gmail.com> Signed-off-by: Waiman Long <longman@redhat.com> Acked-by: Peter Zijlstra <peterz@infradead.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Davidlohr Bueso <dave@stgolabs.net> Cc: Jan Kara <jack@suse.cz> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Matthew Wilcox <willy@infradead.org> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Theodore Y. Ts'o <tytso@mit.edu> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Will Deacon <will.deacon@arm.com> Cc: linux-fsdevel@vger.kernel.org Link: http://lkml.kernel.org/r/1526420991-21213-2-git-send-email-longman@redhat.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
On i.MX6 ULL using PLL3 seems to cause a freeze when setting
the parent to IMX6UL_CLK_PLL3_USB_OTG. This only seems to appear
since commit 6f9575e55632 ("clk: imx: Add CLK_IS_CRITICAL flag
for busy divider and busy mux"), probably because the clock is
now forced to be on.
Fixes: 6f9575e55632("clk: imx: Add CLK_IS_CRITICAL flag for busy divider and busy mux") Signed-off-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
VPIF capture driver expects card name to be set since it
uses it without checking for NULL. The commit which
introduced VPIF display and capture support added card
name only for display, not for capture.
Set it in platform data to probe driver successfully.
While at it, also fix the display card name to something more
appropriate.
Fixes: 85609c1ccda6 ("DaVinci: DM646x - platform changes for vpif capture and display drivers") Signed-off-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
commit a16cb91ad9c4 ("[media] media: vpif: use a configurable
i2c_adapter_id for vpif display") removed hardcoded I2C adaptor
setting in VPIF driver, but missed updating platform data passed
from DM646x board.
Fix it.
Fixes: a16cb91ad9c4 ("[media] media: vpif: use a configurable i2c_adapter_id for vpif display") Signed-off-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
commit b38434145b34 ("ARM: davinci: irqs: Correct McASP1 TX interrupt
definition for DM646x") inadvertently removed priority setting for
timer0_12 (bottom half of timer0). This timer is used as clockevent.
When INTPRIn register setting for an interrupt is left at 0, it is
mapped to FIQ by the AINTC causing the timer interrupt to not get
generated.
Fix it by including an entry for timer0_12 in interrupt priority map
array. While at it, move the clockevent comment to the right place.
Fixes: b38434145b34 ("ARM: davinci: irqs: Correct McASP1 TX interrupt definition for DM646x") Signed-off-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
platform_domain_notifier contains a variable sized array, which the
pm_clk_notify() notifier treats as a NULL terminated array:
for (con_id = clknb->con_ids; *con_id; con_id++)
pm_clk_add(dev, *con_id);
Omitting the initialiser for con_ids means that the array is zero
sized, and there is no NULL terminator. This leads to pm_clk_notify()
overrunning into what ever structure follows, which may not be NULL.
This leads to an oops:
It has been observed that writing 0xF2 to the power register while it
reads as 0xF4 results in the register having the value 0xF0, i.e. clearing
RESUME and setting SUSPENDM in one go does not work. It might also violate
the USB spec to transition directly from resume to suspend, especially
when not taking T_DRSMDN into account. But this is what happens when a
remote wakeup occurs between SetPortFeature USB_PORT_FEAT_SUSPEND on the
root hub and musb_bus_suspend being called.
This commit returns -EBUSY when musb_bus_suspend is called while remote
wakeup is signalled and thus avoids to reset the RESUME bit. Ignoring
this error when musb_port_suspend is called from musb_hub_control is ok.
Signed-off-by: Daniel Glöckner <dg@emlix.com> Signed-off-by: Bin Liu <b-liu@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Some AFS servers refuse to accept unencrypted traffic, so can't be accessed
with kAFS. Set the AF_RXRPC security level to encrypt client calls to deal
with this.
Note that incoming service calls are set by the remote client and so aren't
affected by this.
This requires an AF_RXRPC patch to pass the value set by setsockopt to calls
begun by the kernel.
Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Commit 9e343e87d2c4 ("mtd: cfi: convert inline functions to macros")
changed map_word_andequal() into a macro, but also changed the right
hand side of the comparison from val3 to val2. Change it back to use
val3 on the right hand side.
Thankfully this did not cause a regression because all callers
currently pass the same argument for val2 and val3.
Fixes: 9e343e87d2c4 ("mtd: cfi: convert inline functions to macros") Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Protection key 0 is the default key for all memory and will
not normally come back from pkey_alloc(). But, you might
still want pass it to mprotect_pkey().
This check ensures that you can use pkey 0.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Dave Hansen <dave.hansen@intel.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Michael Ellermen <mpe@ellerman.id.au> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Ram Pai <linuxram@us.ibm.com> Cc: Shuah Khan <shuah@kernel.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-mm@kvack.org Link: http://lkml.kernel.org/r/20180509171356.9E40B254@viggo.jf.intel.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
This makes it possible to to tell what 'prot' a given allocation
is supposed to have. That way, if we want to change just the
pkey, we know what 'prot' to pass to mprotect_pkey().
Also, keep a record of the most recent allocation so the tests
can easily find it.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Dave Hansen <dave.hansen@intel.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Michael Ellermen <mpe@ellerman.id.au> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Ram Pai <linuxram@us.ibm.com> Cc: Shuah Khan <shuah@kernel.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-mm@kvack.org Link: http://lkml.kernel.org/r/20180509171354.AA23E228@viggo.jf.intel.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
We dump out the entire area of the siginfo where the si_pkey_ptr is
supposed to be. But, we do some math on the poitner, which is a u32.
We intended to do byte math, not u32 math on the pointer.
Cast it over to a u8* so it works.
Also, move this block of code to below th si_code check. It doesn't
hurt anything, but the si_pkey field is gibberish for other signal
types.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Dave Hansen <dave.hansen@intel.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Michael Ellermen <mpe@ellerman.id.au> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Ram Pai <linuxram@us.ibm.com> Cc: Shuah Khan <shuah@kernel.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-mm@kvack.org Link: http://lkml.kernel.org/r/20180509171352.9BE09819@viggo.jf.intel.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
In our "exhaust all pkeys" test, we make sure that there
is the expected number available. Turns out that the
test did not cover the execute-only key, but discussed
it anyway. It did *not* discuss the test-allocated
key.
Now that we have a test for the mprotect(PROT_EXEC) case,
this off-by-one issue showed itself. Correct the off-by-
one and add the explanation for the case we missed.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Dave Hansen <dave.hansen@intel.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Michael Ellermen <mpe@ellerman.id.au> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Ram Pai <linuxram@us.ibm.com> Cc: Shuah Khan <shuah@kernel.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-mm@kvack.org Link: http://lkml.kernel.org/r/20180509171350.E1656B95@viggo.jf.intel.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
We currently have an execute-only test, but it is for
the explicit mprotect_pkey() interface. We will soon
add a test for the implicit mprotect(PROT_EXEC)
enterface. We need this code in both tests.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Dave Hansen <dave.hansen@intel.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Michael Ellermen <mpe@ellerman.id.au> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Ram Pai <linuxram@us.ibm.com> Cc: Shuah Khan <shuah@kernel.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-mm@kvack.org Link: http://lkml.kernel.org/r/20180509171347.C64AB733@viggo.jf.intel.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
There is some noisy debug code at the end of the signal handler. It was
disabled by an early, unconditional "return". However, that return also
hid a dprint_in_signal=0, which kept dprint_in_signal=1 and effectively
locked us into permanent dprint_in_signal=1 behavior.
Remove the return and the dead code, fixing dprint_in_signal.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Dave Hansen <dave.hansen@intel.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Michael Ellermen <mpe@ellerman.id.au> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Ram Pai <linuxram@us.ibm.com> Cc: Shuah Khan <shuah@kernel.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-mm@kvack.org Link: http://lkml.kernel.org/r/20180509171342.846B9B2E@viggo.jf.intel.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
do_not_expect_pk_fault() is a helper that we call when we do not expect
a PK fault to have occurred. But, it is a function, which means that
it obscures the line numbers from pkey_assert(). It also gives no
details.
Replace it with an implementation that gives nice line numbers and
also lets callers pass in a more descriptive message about what
happened that caused the unexpected fault.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Dave Hansen <dave.hansen@intel.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Michael Ellermen <mpe@ellerman.id.au> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Ram Pai <linuxram@us.ibm.com> Cc: Shuah Khan <shuah@kernel.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-mm@kvack.org Link: http://lkml.kernel.org/r/20180509171338.55D13B64@viggo.jf.intel.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Since MOV SS and POP SS instructions will delay the exceptions until the
next instruction is executed, single-stepping on it by uprobes must be
prohibited.
uprobe already rejects probing on POP SS (0x1f), but allows probing on MOV
SS (0x8e and reg == 2). This checks the target instruction and if it is
MOV SS or POP SS, returns -ENOTSUPP to reject probing.
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Oleg Nesterov <oleg@redhat.com> Cc: Ricardo Neri <ricardo.neri-calderon@linux.intel.com> Cc: Francis Deslauriers <francis.deslauriers@efficios.com> Cc: Alexei Starovoitov <ast@kernel.org> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Andy Lutomirski <luto@kernel.org> Cc: "H . Peter Anvin" <hpa@zytor.com> Cc: Yonghong Song <yhs@fb.com> Cc: Borislav Petkov <bp@suse.de> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: "David S . Miller" <davem@davemloft.net> Link: https://lkml.kernel.org/r/152587072544.17316.5950935243917346341.stgit@devbox Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Since MOV SS and POP SS instructions will delay the exceptions until the
next instruction is executed, single-stepping on it by kprobes must be
prohibited.
However, kprobes usually executes those instructions directly on trampoline
buffer (a.k.a. kprobe-booster), except for the kprobes which has
post_handler. Thus if kprobe user probes MOV SS with post_handler, it will
do single-stepping on the MOV SS.
This means it is safe that if it is used via ftrace or perf/bpf since those
don't use the post_handler.
Anyway, since the stack switching is a rare case, it is safer just
rejecting kprobes on such instructions.
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Ricardo Neri <ricardo.neri-calderon@linux.intel.com> Cc: Francis Deslauriers <francis.deslauriers@efficios.com> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Alexei Starovoitov <ast@kernel.org> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Andy Lutomirski <luto@kernel.org> Cc: "H . Peter Anvin" <hpa@zytor.com> Cc: Yonghong Song <yhs@fb.com> Cc: Borislav Petkov <bp@suse.de> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: "David S . Miller" <davem@davemloft.net> Link: https://lkml.kernel.org/r/152587069574.17316.3311695234863248641.stgit@devbox Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
While reflinking an inode, we create a new inode in orphan directory,
then take EX lock on it, reflink the original inode to orphan inode and
release EX lock. Once the lock is released another node could request
it in EX mode from ocfs2_recover_orphans() which causes downconvert of
the lock, on this node, to NL mode.
Later we attempt to initialize security acl for the orphan inode and
move it to the reflink destination. However, while doing this we dont
take EX lock on the inode. This could potentially cause problems
because we could be starting transaction, accessing journal and
modifying metadata of the inode while holding NL lock and with another
node holding EX lock on the inode.
Fix this by taking orphan inode cluster lock in EX mode before
initializing security and moving orphan inode to reflink destination.
Use the __tracker variant while taking inode lock to avoid recursive
locking in the ocfs2_init_security_and_acl() call chain.
Link: http://lkml.kernel.org/r/1523475107-7639-1-git-send-email-ashish.samant@oracle.com Signed-off-by: Ashish Samant <ashish.samant@oracle.com> Reviewed-by: Joseph Qi <jiangqi903@gmail.com> Reviewed-by: Junxiao Bi <junxiao.bi@oracle.com> Acked-by: Jun Piao <piaojun@huawei.com> Cc: Mark Fasheh <mark@fasheh.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Changwei Ge <ge.changwei@h3c.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The existing kcore code checks for bad addresses against __va(0) with
the assumption that this is the lowest address on the system. This may
not hold true on some systems (e.g. arm64) and produce overflows and
crashes. Switch to using other functions to validate the address range.
It's currently only seen on arm64 and it's not clear if anyone wants to
use that particular combination on a stable release. So this is not
urgent for stable.
Link: http://lkml.kernel.org/r/20180501201143.15121-1-labbott@redhat.com Signed-off-by: Laura Abbott <labbott@redhat.com> Tested-by: Dave Anderson <anderson@redhat.com> Cc: Kees Cook <keescook@chromium.org> Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org> Cc: Ingo Molnar <mingo@kernel.org> Cc: Andi Kleen <andi@firstfloor.org> Cc: Alexey Dobriyan <adobriyan@gmail.com>a Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The caller calls action's ->init() and passes pointer to "struct tc_action *a",
which later may be initialized to point at the existing action, otherwise
"struct tc_action *a" is still invalid, and therefore dereferencing it is an
error as happens in tcf_idr_release, where refcnt is decremented.
So in case of missing flags tcf_idr_release must be called only for
existing actions.
v2:
- prepare patch for net tree
Fixes: 5e1567aeb7fe ("net sched: skbedit action fix late binding") Signed-off-by: Roman Mashak <mrv@mojatatu.com> Acked-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The IP increment should be done after the hypercall emulation, after
calling the various handlers. In this way, these handlers can accurately
identify the the IP of the VMCALL if they need it.
This patch keeps the same functionality for the Hyper-V handler which does
not use the return code of the standard kvm_skip_emulated_instruction()
call.
Signed-off-by: Marian Rotariu <mrotariu@bitdefender.com>
[Hyper-V hypercalls also need kvm_skip_emulated_instruction() - Paolo] Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
projects / mirror_ubuntu-bionic-kernel.git / log