--- /dev/null
+ALPS HID Touchpad Protocol
+----------------------
+
+Introduction
+------------
+Currently ALPS HID driver supports U1 Touchpad device.
+
+U1 devuce basic information.
+Vender ID 0x044E
+Product ID 0x120B
+Version ID 0x0121
+
+
+HID Descriptor
+------------
+Byte Field Value Notes
+0 wHIDDescLength 001E Length of HID Descriptor : 30 bytes
+2 bcdVersion 0100 Compliant with Version 1.00
+4 wReportDescLength 00B2 Report Descriptor is 178 Bytes (0x00B2)
+6 wReportDescRegister 0002 Identifier to read Report Descriptor
+8 wInputRegister 0003 Identifier to read Input Report
+10 wMaxInputLength 0053 Input Report is 80 Bytes + 2
+12 wOutputRegister 0000 Identifier to read Output Report
+14 wMaxOutputLength 0000 No Output Reports
+16 wCommandRegister 0005 Identifier for Command Register
+18 wDataRegister 0006 Identifier for Data Register
+20 wVendorID 044E Vendor ID 0x044E
+22 wProductID 120B Product ID 0x120B
+24 wVersionID 0121 Version 01.21
+26 RESERVED 0000 RESERVED
+
+
+Report ID
+------------
+ReportID-1 (Input Reports) (HIDUsage-Mouse) for TP&SP
+ReportID-2 (Input Reports) (HIDUsage-keyboard) for TP
+ReportID-3 (Input Reports) (Vendor Usage: Max 10 finger data) for TP
+ReportID-4 (Input Reports) (Vendor Usage: ON bit data) for GP
+ReportID-5 (Feature Reports) Feature Reports
+ReportID-6 (Input Reports) (Vendor Usage: StickPointer data) for SP
+ReportID-7 (Feature Reports) Flash update (Bootloader)
+
+
+Data pattern
+------------
+Case1 ReportID_1 TP/SP Relative/Relative
+Case2 ReportID_3 TP Absolute
+ ReportID_6 SP Absolute
+
+
+Command Read/Write
+------------------
+To read/write to RAM, need to send a commands to the device.
+The command format is as below.
+
+DataByte(SET_REPORT)
+Byte1 Command Byte
+Byte2 Address - Byte 0 (LSB)
+Byte3 Address - Byte 1
+Byte4 Address - Byte 2
+Byte5 Address - Byte 3 (MSB)
+Byte6 Value Byte
+Byte7 Checksum
+
+Command Byte is read=0xD1/write=0xD2 .
+Address is read/write RAM address.
+Value Byte is writing data when you send the write commands.
+When you read RAM, there is no meaning.
+
+DataByte(GET_REPORT)
+Byte1 Response Byte
+Byte2 Address - Byte 0 (LSB)
+Byte3 Address - Byte 1
+Byte4 Address - Byte 2
+Byte5 Address - Byte 3 (MSB)
+Byte6 Value Byte
+Byte7 Checksum
+
+Read value is stored in Value Byte.
+
+
+Packet Format
+Touchpad data byte
+------------------
+ b7 b6 b5 b4 b3 b2 b1 b0
+1 0 0 SW6 SW5 SW4 SW3 SW2 SW1
+2 0 0 0 Fcv Fn3 Fn2 Fn1 Fn0
+3 Xa0_7 Xa0_6 Xa0_5 Xa0_4 Xa0_3 Xa0_2 Xa0_1 Xa0_0
+4 Xa0_15 Xa0_14 Xa0_13 Xa0_12 Xa0_11 Xa0_10 Xa0_9 Xa0_8
+5 Ya0_7 Ya0_6 Ya0_5 Ya0_4 Ya0_3 Ya0_2 Ya0_1 Ya0_0
+6 Ya0_15 Ya0_14 Ya0_13 Ya0_12 Ya0_11 Ya0_10 Ya0_9 Ya0_8
+7 LFB0 Zs0_6 Zs0_5 Zs0_4 Zs0_3 Zs0_2 Zs0_1 Zs0_0
+
+8 Xa1_7 Xa1_6 Xa1_5 Xa1_4 Xa1_3 Xa1_2 Xa1_1 Xa1_0
+9 Xa1_15 Xa1_14 Xa1_13 Xa1_12 Xa1_11 Xa1_10 Xa1_9 Xa1_8
+10 Ya1_7 Ya1_6 Ya1_5 Ya1_4 Ya1_3 Ya1_2 Ya1_1 Ya1_0
+11 Ya1_15 Ya1_14 Ya1_13 Ya1_12 Ya1_11 Ya1_10 Ya1_9 Ya1_8
+12 LFB1 Zs1_6 Zs1_5 Zs1_4 Zs1_3 Zs1_2 Zs1_1 Zs1_0
+
+13 Xa2_7 Xa2_6 Xa2_5 Xa2_4 Xa2_3 Xa2_2 Xa2_1 Xa2_0
+14 Xa2_15 Xa2_14 Xa2_13 Xa2_12 Xa2_11 Xa2_10 Xa2_9 Xa2_8
+15 Ya2_7 Ya2_6 Ya2_5 Ya2_4 Ya2_3 Ya2_2 Ya2_1 Ya2_0
+16 Ya2_15 Ya2_14 Ya2_13 Ya2_12 Ya2_11 Ya2_10 Ya2_9 Ya2_8
+17 LFB2 Zs2_6 Zs2_5 Zs2_4 Zs2_3 Zs2_2 Zs2_1 Zs2_0
+
+18 Xa3_7 Xa3_6 Xa3_5 Xa3_4 Xa3_3 Xa3_2 Xa3_1 Xa3_0
+19 Xa3_15 Xa3_14 Xa3_13 Xa3_12 Xa3_11 Xa3_10 Xa3_9 Xa3_8
+20 Ya3_7 Ya3_6 Ya3_5 Ya3_4 Ya3_3 Ya3_2 Ya3_1 Ya3_0
+21 Ya3_15 Ya3_14 Ya3_13 Ya3_12 Ya3_11 Ya3_10 Ya3_9 Ya3_8
+22 LFB3 Zs3_6 Zs3_5 Zs3_4 Zs3_3 Zs3_2 Zs3_1 Zs3_0
+
+23 Xa4_7 Xa4_6 Xa4_5 Xa4_4 Xa4_3 Xa4_2 Xa4_1 Xa4_0
+24 Xa4_15 Xa4_14 Xa4_13 Xa4_12 Xa4_11 Xa4_10 Xa4_9 Xa4_8
+25 Ya4_7 Ya4_6 Ya4_5 Ya4_4 Ya4_3 Ya4_2 Ya4_1 Ya4_0
+26 Ya4_15 Ya4_14 Ya4_13 Ya4_12 Ya4_11 Ya4_10 Ya4_9 Ya4_8
+27 LFB4 Zs4_6 Zs4_5 Zs4_4 Zs4_3 Zs4_2 Zs4_1 Zs4_0
+
+
+SW1-SW6: SW ON/OFF status
+Xan_15-0(16bit):X Absolute data of the "n"th finger
+Yan_15-0(16bit):Y Absolute data of the "n"th finger
+Zsn_6-0(7bit): Operation area of the "n"th finger
+
+
+StickPointer data byte
+------------------
+ b7 b6 b5 b4 b3 b2 b1 b0
+Byte1 1 1 1 0 1 SW3 SW2 SW1
+Byte2 X7 X6 X5 X4 X3 X2 X1 X0
+Byte3 X15 X14 X13 X12 X11 X10 X9 X8
+Byte4 Y7 Y6 Y5 Y4 Y3 Y2 Y1 Y0
+Byte5 Y15 Y14 Y13 Y12 Y11 Y10 Y9 Y8
+Byte6 Z7 Z6 Z5 Z4 Z3 Z2 Z1 Z0
+Byte7 T&P Z14 Z13 Z12 Z11 Z10 Z9 Z8
+
+SW1-SW3: SW ON/OFF status
+Xn_15-0(16bit):X Absolute data
+Yn_15-0(16bit):Y Absolute data
+Zn_14-0(15bit):Z
--- /dev/null
+/*
+ * Copyright (c) 2016 Masaki Ota <masaki.ota@jp.alps.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the Free
+ * Software Foundation; either version 2 of the License, or (at your option)
+ * any later version.
+ */
+
+#include <linux/kernel.h>
+#include <linux/hid.h>
+#include <linux/input.h>
+#include <linux/input/mt.h>
+#include <linux/module.h>
+#include <asm/unaligned.h>
+#include "hid-ids.h"
+
+/* ALPS Device Product ID */
+#define HID_PRODUCT_ID_T3_BTNLESS 0xD0C0
+#define HID_PRODUCT_ID_COSMO 0x1202
+#define HID_PRODUCT_ID_U1_PTP_1 0x1207
+#define HID_PRODUCT_ID_U1 0x1209
+#define HID_PRODUCT_ID_U1_PTP_2 0x120A
+#define HID_PRODUCT_ID_U1_DUAL 0x120B
+#define HID_PRODUCT_ID_T4_BTNLESS 0x120C
+
+#define DEV_SINGLEPOINT 0x01
+#define DEV_DUALPOINT 0x02
+
+#define U1_MOUSE_REPORT_ID 0x01 /* Mouse data ReportID */
+#define U1_ABSOLUTE_REPORT_ID 0x03 /* Absolute data ReportID */
+#define U1_FEATURE_REPORT_ID 0x05 /* Feature ReportID */
+#define U1_SP_ABSOLUTE_REPORT_ID 0x06 /* Feature ReportID */
+
+#define U1_FEATURE_REPORT_LEN 0x08 /* Feature Report Length */
+#define U1_FEATURE_REPORT_LEN_ALL 0x0A
+#define U1_CMD_REGISTER_READ 0xD1
+#define U1_CMD_REGISTER_WRITE 0xD2
+
+#define U1_DEVTYPE_SP_SUPPORT 0x10 /* SP Support */
+#define U1_DISABLE_DEV 0x01
+#define U1_TP_ABS_MODE 0x02
+#define U1_SP_ABS_MODE 0x80
+
+#define ADDRESS_U1_DEV_CTRL_1 0x00800040
+#define ADDRESS_U1_DEVICE_TYP 0x00800043
+#define ADDRESS_U1_NUM_SENS_X 0x00800047
+#define ADDRESS_U1_NUM_SENS_Y 0x00800048
+#define ADDRESS_U1_PITCH_SENS_X 0x00800049
+#define ADDRESS_U1_PITCH_SENS_Y 0x0080004A
+#define ADDRESS_U1_RESO_DWN_ABS 0x0080004E
+#define ADDRESS_U1_PAD_BTN 0x00800052
+#define ADDRESS_U1_SP_BTN 0x0080009F
+
+#define MAX_TOUCHES 5
+
+/**
+ * struct u1_data
+ *
+ * @input: pointer to the kernel input device
+ * @input2: pointer to the kernel input2 device
+ * @hdev: pointer to the struct hid_device
+ *
+ * @dev_ctrl: device control parameter
+ * @dev_type: device type
+ * @sen_line_num_x: number of sensor line of X
+ * @sen_line_num_y: number of sensor line of Y
+ * @pitch_x: sensor pitch of X
+ * @pitch_y: sensor pitch of Y
+ * @resolution: resolution
+ * @btn_info: button information
+ * @x_active_len_mm: active area length of X (mm)
+ * @y_active_len_mm: active area length of Y (mm)
+ * @x_max: maximum x coordinate value
+ * @y_max: maximum y coordinate value
+ * @btn_cnt: number of buttons
+ * @sp_btn_cnt: number of stick buttons
+ */
+struct u1_dev {
+ struct input_dev *input;
+ struct input_dev *input2;
+ struct hid_device *hdev;
+
+ u8 dev_ctrl;
+ u8 dev_type;
+ u8 sen_line_num_x;
+ u8 sen_line_num_y;
+ u8 pitch_x;
+ u8 pitch_y;
+ u8 resolution;
+ u8 btn_info;
+ u8 sp_btn_info;
+ u32 x_active_len_mm;
+ u32 y_active_len_mm;
+ u32 x_max;
+ u32 y_max;
+ u32 btn_cnt;
+ u32 sp_btn_cnt;
+};
+
+struct u1_dev *priv;
+
+static int u1_read_write_register(struct hid_device *hdev, u32 address,
+ u8 *read_val, u8 write_val, bool read_flag)
+{
+ int ret, i;
+ u8 check_sum;
+ u8 *input;
+ u8 *readbuf;
+
+ input = kzalloc(sizeof(u8)*U1_FEATURE_REPORT_LEN, GFP_KERNEL);
+ if (!input)
+ return -ENOMEM;
+
+ readbuf = kzalloc(sizeof(u8)*U1_FEATURE_REPORT_LEN, GFP_KERNEL);
+ if (!readbuf) {
+ kfree(input);
+ return -ENOMEM;
+ }
+
+ input[0] = U1_FEATURE_REPORT_ID;
+ if (read_flag) {
+ input[1] = U1_CMD_REGISTER_READ;
+ input[6] = 0x00;
+ } else {
+ input[1] = U1_CMD_REGISTER_WRITE;
+ input[6] = write_val;
+ }
+
+ put_unaligned_le32(address, input + 2);
+
+ /* Calculate the checksum */
+ check_sum = U1_FEATURE_REPORT_LEN_ALL;
+ for (i = 0; i < U1_FEATURE_REPORT_LEN - 1; i++)
+ check_sum += input[i];
+
+ input[7] = check_sum;
+ ret = hid_hw_raw_request(hdev, U1_FEATURE_REPORT_ID, input,
+ sizeof(input), HID_FEATURE_REPORT, HID_REQ_SET_REPORT);
+
+ if (ret < 0) {
+ dev_err(&hdev->dev, "failed to read command (%d)\n", ret);
+ goto exit;
+ }
+
+ if (read_flag) {
+ ret = hid_hw_raw_request(hdev, U1_FEATURE_REPORT_ID, readbuf,
+ sizeof(readbuf), HID_FEATURE_REPORT,
+ HID_REQ_GET_REPORT);
+
+ if (ret < 0) {
+ dev_err(&hdev->dev, "failed read register (%d)\n", ret);
+ goto exit;
+ }
+
+ *read_val = readbuf[6];
+ }
+
+ kfree(input);
+ kfree(readbuf);
+ return 0;
+
+exit:
+ kfree(input);
+ kfree(readbuf);
+ return ret;
+}
+
+static int alps_raw_event(struct hid_device *hdev,
+ struct hid_report *report, u8 *data, int size)
+{
+ int x[MAX_TOUCHES], y[MAX_TOUCHES], z[MAX_TOUCHES];
+ int i, left, right, middle;
+ short sp_x, sp_y, sp_z;
+ struct u1_dev *hdata = hid_get_drvdata(hdev);
+
+ switch (data[0]) {
+ case U1_MOUSE_REPORT_ID:
+ break;
+ case U1_FEATURE_REPORT_ID:
+ break;
+ case U1_ABSOLUTE_REPORT_ID:
+ for (i = 0; i < MAX_TOUCHES; i++) {
+ x[i] = (data[3+(5*i)] | (data[4+(5*i)] << 8));
+ y[i] = (data[5+(5*i)] | (data[6+(5*i)] << 8));
+ z[i] = data[7+(5*i)] & 0x7F;
+ left = data[1] & 0x1;
+ right = (data[1] & 0x2) >> 1;
+ middle = (data[1] & 0x4) >> 2;
+
+ input_mt_slot(hdata->input, i);
+
+ if (z[i] != 0) {
+ input_mt_report_slot_state(hdata->input,
+ MT_TOOL_FINGER, 1);
+ } else {
+ input_mt_report_slot_state(hdata->input,
+ MT_TOOL_FINGER, 0);
+ break;
+ }
+
+ input_event(hdata->input, EV_ABS,
+ ABS_MT_POSITION_X, x[i]);
+ input_event(hdata->input, EV_ABS,
+ ABS_MT_POSITION_Y, y[i]);
+ input_event(hdata->input, EV_ABS,
+ ABS_MT_PRESSURE, z[i]);
+ }
+
+ input_mt_sync_frame(hdata->input);
+ input_sync(hdata->input);
+
+ input_event(hdata->input, EV_KEY, BTN_LEFT, left);
+ input_event(hdata->input, EV_KEY, BTN_RIGHT, right);
+ input_event(hdata->input, EV_KEY, BTN_MIDDLE, middle);
+
+ return 1;
+
+ case U1_SP_ABSOLUTE_REPORT_ID:
+ sp_x = (data[2] | (data[3] << 8));
+ sp_y = (data[4] | (data[5] << 8));
+ sp_z = (data[6] | data[7]) & 0x7FFF;
+ left = data[1] & 0x1;
+ right = (data[1] & 0x2) >> 1;
+ middle = (data[1] & 0x4) >> 2;
+
+ sp_x = sp_x / 8;
+ sp_y = sp_y / 8;
+
+ input_event(priv->input2, EV_REL, REL_X, sp_x);
+ input_event(priv->input2, EV_REL, REL_Y, sp_y);
+
+ input_event(priv->input2, EV_KEY, BTN_LEFT, left);
+ input_event(priv->input2, EV_KEY, BTN_RIGHT, right);
+ input_event(priv->input2, EV_KEY, BTN_MIDDLE, middle);
+
+ input_sync(priv->input2);
+
+ return 1;
+ }
+
+ return 0;
+}
+
+#ifdef CONFIG_PM
+static int alps_post_reset(struct hid_device *hdev)
+{
+ return u1_read_write_register(hdev, ADDRESS_U1_DEV_CTRL_1,
+ NULL, U1_TP_ABS_MODE, false);
+}
+
+static int alps_post_resume(struct hid_device *hdev)
+{
+ return u1_read_write_register(hdev, ADDRESS_U1_DEV_CTRL_1,
+ NULL, U1_TP_ABS_MODE, false);
+}
+#endif /* CONFIG_PM */
+
+static int alps_input_configured(struct hid_device *hdev, struct hid_input *hi)
+{
+ struct u1_dev *data = hid_get_drvdata(hdev);
+ struct input_dev *input = hi->input, *input2;
+ struct u1_dev devInfo;
+ int ret;
+ int res_x, res_y, i;
+
+ /* Check device product ID */
+ switch (hdev->product) {
+ case HID_PRODUCT_ID_U1:
+ case HID_PRODUCT_ID_U1_DUAL:
+ break;
+ default:
+ return 0;
+ }
+
+ data->input = input;
+
+ hid_dbg(hdev, "Opening low level driver\n");
+ ret = hid_hw_open(hdev);
+ if (ret)
+ return ret;
+
+ /* Allow incoming hid reports */
+ hid_device_io_start(hdev);
+
+ /* Device initialization */
+ ret = u1_read_write_register(hdev, ADDRESS_U1_DEV_CTRL_1,
+ &devInfo.dev_ctrl, 0, true);
+ if (ret < 0) {
+ dev_err(&hdev->dev, "failed U1_DEV_CTRL_1 (%d)\n", ret);
+ goto exit;
+ }
+
+ devInfo.dev_ctrl &= ~U1_DISABLE_DEV;
+ devInfo.dev_ctrl |= U1_TP_ABS_MODE;
+ ret = u1_read_write_register(hdev, ADDRESS_U1_DEV_CTRL_1,
+ NULL, devInfo.dev_ctrl, false);
+ if (ret < 0) {
+ dev_err(&hdev->dev, "failed to change TP mode (%d)\n", ret);
+ goto exit;
+ }
+
+ ret = u1_read_write_register(hdev, ADDRESS_U1_NUM_SENS_X,
+ &devInfo.sen_line_num_x, 0, true);
+ if (ret < 0) {
+ dev_err(&hdev->dev, "failed U1_NUM_SENS_X (%d)\n", ret);
+ goto exit;
+ }
+
+ ret = u1_read_write_register(hdev, ADDRESS_U1_NUM_SENS_Y,
+ &devInfo.sen_line_num_y, 0, true);
+ if (ret < 0) {
+ dev_err(&hdev->dev, "failed U1_NUM_SENS_Y (%d)\n", ret);
+ goto exit;
+ }
+
+ ret = u1_read_write_register(hdev, ADDRESS_U1_PITCH_SENS_X,
+ &devInfo.pitch_x, 0, true);
+ if (ret < 0) {
+ dev_err(&hdev->dev, "failed U1_PITCH_SENS_X (%d)\n", ret);
+ goto exit;
+ }
+
+ ret = u1_read_write_register(hdev, ADDRESS_U1_PITCH_SENS_Y,
+ &devInfo.pitch_y, 0, true);
+ if (ret < 0) {
+ dev_err(&hdev->dev, "failed U1_PITCH_SENS_Y (%d)\n", ret);
+ goto exit;
+ }
+
+ ret = u1_read_write_register(hdev, ADDRESS_U1_RESO_DWN_ABS,
+ &devInfo.resolution, 0, true);
+ if (ret < 0) {
+ dev_err(&hdev->dev, "failed U1_RESO_DWN_ABS (%d)\n", ret);
+ goto exit;
+ }
+
+ ret = u1_read_write_register(hdev, ADDRESS_U1_PAD_BTN,
+ &devInfo.btn_info, 0, true);
+ if (ret < 0) {
+ dev_err(&hdev->dev, "failed U1_PAD_BTN (%d)\n", ret);
+ goto exit;
+ }
+
+ /* Check StickPointer device */
+ ret = u1_read_write_register(hdev, ADDRESS_U1_DEVICE_TYP,
+ &devInfo.dev_type, 0, true);
+ if (ret < 0) {
+ dev_err(&hdev->dev, "failed U1_DEVICE_TYP (%d)\n", ret);
+ goto exit;
+ }
+
+ devInfo.x_active_len_mm =
+ (devInfo.pitch_x * (devInfo.sen_line_num_x - 1)) / 10;
+ devInfo.y_active_len_mm =
+ (devInfo.pitch_y * (devInfo.sen_line_num_y - 1)) / 10;
+
+ devInfo.x_max =
+ (devInfo.resolution << 2) * (devInfo.sen_line_num_x - 1);
+ devInfo.y_max =
+ (devInfo.resolution << 2) * (devInfo.sen_line_num_y - 1);
+
+ __set_bit(EV_ABS, input->evbit);
+ input_set_abs_params(input, ABS_MT_POSITION_X, 1, devInfo.x_max, 0, 0);
+ input_set_abs_params(input, ABS_MT_POSITION_Y, 1, devInfo.y_max, 0, 0);
+
+ if (devInfo.x_active_len_mm && devInfo.y_active_len_mm) {
+ res_x = (devInfo.x_max - 1) / devInfo.x_active_len_mm;
+ res_y = (devInfo.y_max - 1) / devInfo.y_active_len_mm;
+
+ input_abs_set_res(input, ABS_MT_POSITION_X, res_x);
+ input_abs_set_res(input, ABS_MT_POSITION_Y, res_y);
+ }
+
+ input_set_abs_params(input, ABS_MT_PRESSURE, 0, 64, 0, 0);
+
+ input_mt_init_slots(input, MAX_TOUCHES, INPUT_MT_POINTER);
+
+ __set_bit(EV_KEY, input->evbit);
+ if ((devInfo.btn_info & 0x0F) == (devInfo.btn_info & 0xF0) >> 4) {
+ devInfo.btn_cnt = (devInfo.btn_info & 0x0F);
+ } else {
+ /* Button pad */
+ devInfo.btn_cnt = 1;
+ __set_bit(INPUT_PROP_BUTTONPAD, input->propbit);
+ }
+
+ for (i = 0; i < devInfo.btn_cnt; i++)
+ __set_bit(BTN_LEFT + i, input->keybit);
+
+
+ /* Stick device initialization */
+ if (devInfo.dev_type & U1_DEVTYPE_SP_SUPPORT) {
+
+ priv = kzalloc(sizeof(struct u1_dev), GFP_KERNEL);
+ if (!priv) {
+ hid_device_io_stop(hdev);
+ hid_hw_close(hdev);
+ return -ENOMEM;
+ }
+
+ input2 = input_allocate_device();
+ if (!input2) {
+ input_free_device(input2);
+ goto exit;
+ }
+
+ priv->input2 = input2;
+
+ devInfo.dev_ctrl |= U1_SP_ABS_MODE;
+ ret = u1_read_write_register(hdev, ADDRESS_U1_DEV_CTRL_1,
+ NULL, devInfo.dev_ctrl, false);
+ if (ret < 0) {
+ dev_err(&hdev->dev, "failed SP mode (%d)\n", ret);
+ input_free_device(input2);
+ goto exit;
+ }
+
+ ret = u1_read_write_register(hdev, ADDRESS_U1_SP_BTN,
+ &devInfo.sp_btn_info, 0, true);
+ if (ret < 0) {
+ dev_err(&hdev->dev, "failed U1_SP_BTN (%d)\n", ret);
+ input_free_device(input2);
+ goto exit;
+ }
+
+ input2->phys = input->phys;
+ input2->name = "DualPoint Stick";
+ input2->id.bustype = BUS_I2C;
+ input2->id.vendor = input->id.vendor;
+ input2->id.product = input->id.product;
+ input2->id.version = input->id.version;
+ input2->dev.parent = input->dev.parent;
+
+ __set_bit(EV_KEY, input2->evbit);
+ devInfo.sp_btn_cnt = (devInfo.sp_btn_info & 0x0F);
+ for (i = 0; i < devInfo.sp_btn_cnt; i++)
+ __set_bit(BTN_LEFT + i, input2->keybit);
+
+ __set_bit(EV_REL, input2->evbit);
+ __set_bit(REL_X, input2->relbit);
+ __set_bit(REL_Y, input2->relbit);
+ __set_bit(INPUT_PROP_POINTER, input2->propbit);
+ __set_bit(INPUT_PROP_POINTING_STICK, input2->propbit);
+
+ if (input_register_device(priv->input2)) {
+ input_free_device(input2);
+ goto exit;
+ }
+ }
+
+exit:
+ hid_device_io_stop(hdev);
+ hid_hw_close(hdev);
+ return ret;
+}
+
+static int alps_input_mapping(struct hid_device *hdev,
+ struct hid_input *hi, struct hid_field *field,
+ struct hid_usage *usage, unsigned long **bit, int *max)
+{
+ return -1;
+}
+
+static int alps_probe(struct hid_device *hdev, const struct hid_device_id *id)
+{
+ struct u1_dev *data = NULL;
+ int ret;
+
+ data = devm_kzalloc(&hdev->dev, sizeof(struct u1_dev), GFP_KERNEL);
+ if (!data)
+ return -ENOMEM;
+
+ data->hdev = hdev;
+ hid_set_drvdata(hdev, data);
+
+ hdev->quirks |= HID_QUIRK_NO_INIT_REPORTS;
+
+ ret = hid_parse(hdev);
+ if (ret) {
+ hid_err(hdev, "parse failed\n");
+ return ret;
+ }
+
+ ret = hid_hw_start(hdev, HID_CONNECT_DEFAULT);
+ if (ret) {
+ hid_err(hdev, "hw start failed\n");
+ return ret;
+ }
+
+ return 0;
+}
+
+static void alps_remove(struct hid_device *hdev)
+{
+ hid_hw_stop(hdev);
+ kfree(priv);
+}
+
+static const struct hid_device_id alps_id[] = {
+ { HID_DEVICE(HID_BUS_ANY, HID_GROUP_ANY,
+ USB_VENDOR_ID_ALPS_JP, HID_ANY_ID) },
+ { }
+};
+MODULE_DEVICE_TABLE(hid, alps_id);
+
+static struct hid_driver alps_driver = {
+ .name = "hid-alps",
+ .id_table = alps_id,
+ .probe = alps_probe,
+ .remove = alps_remove,
+ .raw_event = alps_raw_event,
+ .input_mapping = alps_input_mapping,
+ .input_configured = alps_input_configured,
+#ifdef CONFIG_PM
+ .resume = alps_post_resume,
+ .reset_resume = alps_post_reset,
+#endif
+};
+
+module_hid_driver(alps_driver);
+
+MODULE_AUTHOR("Masaki Ota <masaki.ota@jp.alps.com>");
+MODULE_DESCRIPTION("ALPS HID driver");
+MODULE_LICENSE("GPL");
projects / mirror_ubuntu-zesty-kernel.git / commitdiff