* Copy-on-write clone
-* Various raid levels: RAID0, RAID1, RAID10, RAIDZ-1, RAIDZ-2 and RAIDZ-3
+* Various raid levels: RAID0, RAID1, RAID10, RAIDZ-1, RAIDZ-2, RAIDZ-3,
+dRAID, dRAID2, dRAID3
* Can use SSD for cache
* Designed for high storage capacities
-* Protection against data corruption
-
* Asynchronous replication over network
* Open Source
~~~~~~~~
ZFS depends heavily on memory, so you need at least 8GB to start. In
-practice, use as much you can get for your hardware/budget. To prevent
+practice, use as much as you can get for your hardware/budget. To prevent
data corruption, we recommend the use of high quality ECC RAM.
If you use a dedicated cache and/or log disk, you should use an
enterprise class SSD (e.g. Intel SSD DC S3700 Series). This can
increase the overall performance significantly.
-IMPORTANT: Do not use ZFS on top of hardware controller which has its
-own cache management. ZFS needs to directly communicate with disks. An
-HBA adapter is the way to go, or something like LSI controller flashed
-in ``IT'' mode.
+IMPORTANT: Do not use ZFS on top of a hardware RAID controller which has its
+own cache management. ZFS needs to communicate directly with the disks. An
+HBA adapter or something like an LSI controller flashed in ``IT'' mode is more
+appropriate.
If you are experimenting with an installation of {pve} inside a VM
(Nested Virtualization), don't use `virtio` for disks of that VM,
-since they are not supported by ZFS. Use IDE or SCSI instead (works
-also with `virtio` SCSI controller type).
+as they are not supported by ZFS. Use IDE or SCSI instead (also works
+with the `virtio` SCSI controller type).
Installation as Root File System
performance, depending on the disks underneath, and cannot be changed later on.
Mirror vdevs (RAID1, RAID10) have favorable behavior for VM workloads. Use
-them, unless your environmanet has specific needs and charactersitics where
+them, unless your environment has specific needs and characteristics where
RAIDZ performance characteristics are acceptable.
+ZFS dRAID
+~~~~~~~~~
+
+In a ZFS dRAID (declustered RAID) the hot spare drive(s) participate in the RAID.
+Their spare capacity is reserved and used for rebuilding when one drive fails.
+This provides, depending on the configuration, faster rebuilding compared to a
+RAIDZ in case of drive failure. More information can be found in the official
+OpenZFS documentation. footnote:[OpenZFS dRAID
+https://openzfs.github.io/openzfs-docs/Basic%20Concepts/dRAID%20Howto.html]
+
+NOTE: dRAID is intended for more than 10-15 disks in a dRAID. A RAIDZ
+setup should be better for a lower amount of disks in most use cases.
+
+NOTE: The GUI requires one more disk than the minimum (i.e. dRAID1 needs 3). It
+expects that a spare disk is added as well.
+
+ * `dRAID1` or `dRAID`: requires at least 2 disks, one can fail before data is
+lost
+ * `dRAID2`: requires at least 3 disks, two can fail before data is lost
+ * `dRAID3`: requires at least 4 disks, three can fail before data is lost
+
+
+Additional information can be found on the manual page:
+
+----
+# man zpoolconcepts
+----
+
+Spares and Data
+^^^^^^^^^^^^^^^
+The number of `spares` tells the system how many disks it should keep ready in
+case of a disk failure. The default value is 0 `spares`. Without spares,
+rebuilding won't get any speed benefits.
+
+`data` defines the number of devices in a redundancy group. The default value is
+8. Except when `disks - parity - spares` equal something less than 8, the lower
+number is used. In general, a smaller number of `data` devices leads to higher
+IOPS, better compression ratios and faster resilvering, but defining fewer data
+devices reduces the available storage capacity of the pool.
+
+
Bootloader
~~~~~~~~~~
-Depending on whether the system is booted in EFI or legacy BIOS mode the
-{pve} installer sets up either `grub` or `systemd-boot` as main bootloader.
-See the chapter on xref:sysboot[{pve} host bootladers] for details.
+{pve} uses xref:sysboot_proxmox_boot_tool[`proxmox-boot-tool`] to manage the
+bootloader configuration.
+See the chapter on xref:sysboot[{pve} host bootloaders] for details.
ZFS Administration
.Changing a failed bootable device
-Depending on how {pve} was installed it is either using `grub` or `systemd-boot`
-as bootloader (see xref:sysboot[Host Bootloader]).
+Depending on how {pve} was installed it is either using `systemd-boot` or `grub`
+through `proxmox-boot-tool`
+footnote:[Systems installed with {pve} 6.4 or later, EFI systems installed with
+{pve} 5.4 or later] or plain `grub` as bootloader (see
+xref:sysboot[Host Bootloader]). You can check by running:
+
+----
+# proxmox-boot-tool status
+----
The first steps of copying the partition table, reissuing GUIDs and replacing
the ZFS partition are the same. To make the system bootable from the new disk,
NOTE: Use the `zpool status -v` command to monitor how far the resilvering
process of the new disk has progressed.
-.With `systemd-boot`:
+.With `proxmox-boot-tool`:
----
-# pve-efiboot-tool format <new disk's ESP>
-# pve-efiboot-tool init <new disk's ESP>
+# proxmox-boot-tool format <new disk's ESP>
+# proxmox-boot-tool init <new disk's ESP>
----
NOTE: `ESP` stands for EFI System Partition, which is setup as partition #2 on
bootable disks setup by the {pve} installer since version 5.4. For details, see
-xref:sysboot_systemd_boot_setup[Setting up a new partition for use as synced ESP].
+xref:sysboot_proxmox_boot_setup[Setting up a new partition for use as synced ESP].
-.With `grub`:
+.With plain `grub`:
----
# grub-install <new disk>
----
+NOTE: plain `grub` is only used on systems installed with {pve} 6.3 or earlier,
+which have not been manually migrated to using `proxmox-boot-tool` yet.
-Activate E-Mail Notification
-~~~~~~~~~~~~~~~~~~~~~~~~~~~~
-ZFS comes with an event daemon, which monitors events generated by the
-ZFS kernel module. The daemon can also send emails on ZFS events like
-pool errors. Newer ZFS packages ship the daemon in a separate package,
-and you can install it using `apt-get`:
+Configure E-Mail Notification
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
-----
-# apt-get install zfs-zed
-----
+ZFS comes with an event daemon `ZED`, which monitors events generated by the ZFS
+kernel module. The daemon can also send emails on ZFS events like pool errors.
+Newer ZFS packages ship the daemon in a separate `zfs-zed` package, which should
+already be installed by default in {pve}.
-To activate the daemon it is necessary to edit `/etc/zfs/zed.d/zed.rc` with your
-favourite editor, and uncomment the `ZED_EMAIL_ADDR` setting:
+You can configure the daemon via the file `/etc/zfs/zed.d/zed.rc` with your
+favorite editor. The required setting for email notification is
+`ZED_EMAIL_ADDR`, which is set to `root` by default.
--------
ZED_EMAIL_ADDR="root"
Please note {pve} forwards mails to `root` to the email address
configured for the root user.
-IMPORTANT: The only setting that is required is `ZED_EMAIL_ADDR`. All
-other settings are optional.
-
[[sysadmin_zfs_limit_memory_usage]]
Limit ZFS Memory Usage
~~~~~~~~~~~~~~~~~~~~~~
-It is good to use at most 50 percent (which is the default) of the
-system memory for ZFS ARC to prevent performance shortage of the
-host. Use your preferred editor to change the configuration in
-`/etc/modprobe.d/zfs.conf` and insert:
+ZFS uses '50 %' of the host memory for the **A**daptive **R**eplacement
+**C**ache (ARC) by default. Allocating enough memory for the ARC is crucial for
+IO performance, so reduce it with caution. As a general rule of thumb, allocate
+at least +2 GiB Base + 1 GiB/TiB-Storage+. For example, if you have a pool with
++8 TiB+ of available storage space then you should use +10 GiB+ of memory for
+the ARC.
+
+You can change the ARC usage limit for the current boot (a reboot resets this
+change again) by writing to the +zfs_arc_max+ module parameter directly:
+
+----
+ echo "$[10 * 1024*1024*1024]" >/sys/module/zfs/parameters/zfs_arc_max
+----
+
+To *permanently change* the ARC limits, add the following line to
+`/etc/modprobe.d/zfs.conf`:
--------
options zfs zfs_arc_max=8589934592
--------
-This example setting limits the usage to 8GB.
+This example setting limits the usage to 8 GiB ('8 * 2^30^').
+
+IMPORTANT: In case your desired +zfs_arc_max+ value is lower than or equal to
++zfs_arc_min+ (which defaults to 1/32 of the system memory), +zfs_arc_max+ will
+be ignored unless you also set +zfs_arc_min+ to at most +zfs_arc_max - 1+.
+
+----
+echo "$[8 * 1024*1024*1024 - 1]" >/sys/module/zfs/parameters/zfs_arc_min
+echo "$[8 * 1024*1024*1024]" >/sys/module/zfs/parameters/zfs_arc_max
+----
+
+This example setting (temporarily) limits the usage to 8 GiB ('8 * 2^30^') on
+systems with more than 256 GiB of total memory, where simply setting
++zfs_arc_max+ alone would not work.
[IMPORTANT]
====
-If your root file system is ZFS you must update your initramfs every
+If your root file system is ZFS, you must update your initramfs every
time this value changes:
----
-# update-initramfs -u
+# update-initramfs -u -k all
----
+
+You *must reboot* to activate these changes.
====
We strongly recommend to use enough memory, so that you normally do not
run into low memory situations. Should you need or want to add swap, it is
-preferred to create a partition on a physical disk and use it as swapdevice.
+preferred to create a partition on a physical disk and use it as a swap device.
You can leave some space free for this purpose in the advanced options of the
installer. Additionally, you can lower the
``swappiness'' value. A good value for servers is 10:
Encrypted ZFS Datasets
~~~~~~~~~~~~~~~~~~~~~~
+WARNING: Native ZFS encryption in {pve} is experimental. Known limitations and
+issues include Replication with encrypted datasets
+footnote:[https://bugzilla.proxmox.com/show_bug.cgi?id=2350],
+as well as checksum errors when using Snapshots or ZVOLs.
+footnote:[https://github.com/openzfs/zfs/issues/11688]
+
ZFS on Linux version 0.8.0 introduced support for native encryption of
datasets. After an upgrade from previous ZFS on Linux versions, the encryption
feature can be enabled per pool:
ZFS datasets expose the `special_small_blocks=<size>` property. `size` can be
`0` to disable storing small file blocks on the `special` device or a power of
-two in the range between `512B` to `128K`. After setting the property new file
+two in the range between `512B` to `1M`. After setting the property new file
blocks smaller than `size` will be allocated on the `special` device.
IMPORTANT: If the value for `special_small_blocks` is greater than or equal to
----
# zfs set special_small_blocks=0 <pool>/<filesystem>
----
+
+[[sysadmin_zfs_features]]
+ZFS Pool Features
+~~~~~~~~~~~~~~~~~
+
+Changes to the on-disk format in ZFS are only made between major version changes
+and are specified through *features*. All features, as well as the general
+mechanism are well documented in the `zpool-features(5)` manpage.
+
+Since enabling new features can render a pool not importable by an older version
+of ZFS, this needs to be done actively by the administrator, by running
+`zpool upgrade` on the pool (see the `zpool-upgrade(8)` manpage).
+
+Unless you need to use one of the new features, there is no upside to enabling
+them.
+
+In fact, there are some downsides to enabling new features:
+
+* A system with root on ZFS, that still boots using `grub` will become
+ unbootable if a new feature is active on the rpool, due to the incompatible
+ implementation of ZFS in grub.
+* The system will not be able to import any upgraded pool when booted with an
+ older kernel, which still ships with the old ZFS modules.
+* Booting an older {pve} ISO to repair a non-booting system will likewise not
+ work.
+
+IMPORTANT: Do *not* upgrade your rpool if your system is still booted with
+`grub`, as this will render your system unbootable. This includes systems
+installed before {pve} 5.4, and systems booting with legacy BIOS boot (see
+xref:sysboot_determine_bootloader_used[how to determine the bootloader]).
+
+.Enable new features for a ZFS pool:
+----
+# zpool upgrade <pool>
+----
projects / pve-docs.git / blobdiff