New chapter "Hyper-converged Infrastructure" with Proxmox ceph server

The new chapter "Hyper-converged Infrastructure" is added. It contains a general statement about it and
as subchapter "Ceph server in Proxmox VE Cluster"

The latter is derived from the corresponding Wiki article. Since the Wiki article contains a lot of
additional best practice information it is not obsolete yet. A combined source for both Wiki and Administration Guide
will be made later.

Signed-off-by: Friedrich Ramberger <f.ramberger@proxmox.com>

diff --git a/ceph-server.adoc b/ceph-server.adoc
new file mode 100644 (file)
index 0000000..39c9b74
--- /dev/null
+++ b/ceph-server.adoc
@@ -0,0 +1,138 @@
+Ceph Server in Proxmox VE Cluster
+---------------------------------
+
+
+It is possible to install at Proxmox VE cluster nodes a Ceph Server for RADOS Block Devices (RBD), see 
+xref:ceph_rados_block_devices[chapter Ceph RADOS Block Devices (RBD)] 
+
+
+Precondition
+~~~~~~~~~~~~
+
+There should be at least three (preferably) identical servers for setup which build together a Proxmox Cluster.
+
+
+A 10Gb network is recommmended, exclusively used for Ceph. If there are no 10Gb switches available meshed network is 
+also an option, see {webwiki-url}Full_Mesh_Network_for_Ceph_Server[wiki]. 
+
+
+Check also the recommendations from http://docs.ceph.com/docs/jewel/start/hardware-recommendations/[Ceph's Website].
+
+
+Installation of Ceph Packages
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+
+On each node run the installation script as follows:
+
+[source,bash]
+----
+pveceph install -version jewel
+----
+
+
+This sets up an 'apt' package repository in /etc/apt/sources.list.d/ceph.list and installs the required software.
+
+
+Creating initial Ceph configuration
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+After installation of packages, you need to create an initial Ceph configuration on just one node, based on your network (10.10.10.0/24 in the following example) dedicated for Ceph: 
+
+[source,bash]
+----
+pveceph init --network 10.10.10.0/24
+----
+
+This creates an initial config at /etc/pve/ceph.conf. That file is automatically distributed to all Proxmox VE nodes by using xref:proxmox_cluster_file_system[pmxcfs]. The command also creates a symbolic link from /etc/ceph/ceph.conf pointing to that file. So you can simply run Ceph commands without the need to specify a configuration file. 
+
+
+Creating Ceph Monitors
+~~~~~~~~~~~~~~~~~~~~~~
+
+On each node where a monitor is requested (at least 3 are recommended) create it by using the "Ceph" item in the GUI or run 
+
+
+[source,bash]
+----
+pveceph createmon
+----
+
+
+Creating Ceph OSDs
+~~~~~~~~~~~~~~~~~~
+
+
+via GUI or via CLI as follows:
+
+[source,bash]
+----
+pveceph createosd /dev/sd[X]
+----
+
+If you want to use a dedicated SSD journal disk: 
+
+NOTE: In order to use a dedicated journal disk (SSD), the disk needs to have a GPT partition table. You can create this with 'gdisk /dev/sd(x)'. If there is no GPT, you cannot select the disk as journal. Currently the journal size is fixed to 5 GB.
+
+
+[source,bash]
+----
+pveceph createosd /dev/sd[X] -journal_dev /dev/sd[X]
+----
+
+Example: /dev/sdf as data disk (4TB) and /dev/sdb is the dedicated SSD journal disk 
+
+[source,bash]
+----
+pveceph createosd /dev/sdf -journal_dev /dev/sdb
+----
+
+
+This partitions the disk (data and journal partition), creates filesystems and starts the OSD, afterwards it is running and fully functional. Please create at least 12 OSDs, distributed among your nodes (4 on each node). 
+
+It should be noted that this command refuses to initialize disk when it detects existing data. So if you want to overwrite a disk you should remove existing data first. You can do that using: 
+
+[source,bash]
+----
+ceph-disk zap /dev/sd[X]
+----
+
+
+You can create OSDs containing both journal and data partitions or you can place the journal on a dedicated SSD. Using a SSD journal disk is highly recommended if you expect good performance. 
+
+
+
+Ceph Pools
+~~~~~~~~~~
+
+
+The standard installation creates per default the pool 'rbd', additional pools can be created via GUI.
+
+
+
+Ceph Client
+~~~~~~~~~~~
+
+
+You can then configure Proxmox VE to use such pools to store VM images, just use the GUI ("Add Storage": RBD, see section xref:ceph_rados_block_devices[Ceph RADOS Block Devices (RBD)]).
+
+
+You also need to copy the keyring to a predefined location.
+NOTE: that the file name needs to be storage id + .keyring - storage id is the expression after 'rbd:' in /etc/pve/storage.cfg which is 'my-ceph-storage' in the following example:
+
+[source,bash]
+----
+mkdir /etc/pve/priv/ceph
+cp /etc/ceph/ceph.client.admin.keyring /etc/pve/priv/ceph/my-ceph-storage.keyring
+----
+
+
+
+
+
+
+
+
+
+
+

diff --git a/hyper-converged-infrastructure.adoc b/hyper-converged-infrastructure.adoc
new file mode 100644 (file)
index 0000000..2948498
--- /dev/null
+++ b/hyper-converged-infrastructure.adoc
@@ -0,0 +1,12 @@
+[[chapter_hyper_converged_infrastructure]]
+Hyper-converged Infrastructure
+==============================
+
+Proxmox VE has all the https://en.wikipedia.org/wiki/Hyper-converged_infrastructure[Hyper-converged Infrastructure] capabilities needed to deploy and manage a complete open source hyper-converged 
+infrastructure. 
+It integrates tightly compute, networking, and storage resources into a single deployment unit and you can manage everything with the centralized web management interface. 
+Proxmox VE unifies your compute and storage systems, i.e. you can use the same physical nodes within a cluster for both computing (processing VMs and Containers) as well as for replicated storage.
+
+
+include::ceph-server.adoc[]
+

diff --git a/pmxcfs.adoc b/pmxcfs.adoc
index d3b7a715d4d464d33c0ad6ee5f2c817f231456e9..8f8c81c579c32e95ded361af8e518375ea866275 100644 (file)
--- a/pmxcfs.adoc
+++ b/pmxcfs.adoc
@@ -18,6 +18,7 @@ DESCRIPTION
 endif::manvolnum[]
 
 ifndef::manvolnum[]
+[[proxmox_cluster_file_system]]
 Proxmox Cluster File System (pmxcfs)
 ====================================
 :pve-toplevel:

diff --git a/pve-admin-guide.adoc b/pve-admin-guide.adoc
index 5cb85bbbedd8d5c545d27b5d028bd7879884317f..b783cd0eb9c8de688673a10232e92ab167aef2fc 100644 (file)
--- a/pve-admin-guide.adoc
+++ b/pve-admin-guide.adoc
@@ -25,6 +25,8 @@ include::pve-installation.adoc[]
 
 include::sysadmin.adoc[]
 
+include::hyper-converged-infrastructure.adoc[]
+
 include::pve-gui.adoc[]
 
 include::pvecm.adoc[]

diff --git a/pve-storage-rbd.adoc b/pve-storage-rbd.adoc
index c33b70e0fd1af14cfe17ba2d69605f14db50ee2b..c782ee190a09c9d6ba0d3d236eee11a7115b8ef5 100644 (file)
--- a/pve-storage-rbd.adoc
+++ b/pve-storage-rbd.adoc
@@ -1,3 +1,4 @@
+[[ceph_rados_block_devices]]
 Ceph RADOS Block Devices (RBD)
 ------------------------------
 ifdef::wiki[]