Add section with more infos about ZFS RAID levels

This new section explains the performance and failure properties of
mirror and RAIDZ VDEVs as well as the "unexpected" higher space usage by
ZVOLs on a RAIDZ.

Signed-off-by: Aaron Lauterer <a.lauterer@proxmox.com>

diff --git a/local-zfs.adoc b/local-zfs.adoc
index fd03e891cd7c0faadc6ab83f78e43377fb3019fe..5b36f5e72e3f03986796fac78e168a81772d25db 100644 (file)
--- a/local-zfs.adoc
+++ b/local-zfs.adoc
@@ -151,6 +151,101 @@ rpool/swap        4.25G  7.69T    64K  -
 ----
 
 
+[[sysadmin_zfs_raid_considerations]]
+ZFS RAID Level Considerations
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+There are a few factors to take into consideration when choosing the layout of
+a ZFS pool. The basic building block of a ZFS pool is the virtual device, or
+`vdev`. All vdevs in a pool are used equally and the data is striped among them
+(RAID0). Check the `zpool(8)` manpage for more details on vdevs.
+
+[[sysadmin_zfs_raid_performance]]
+Performance
+^^^^^^^^^^^
+
+Each `vdev` type has different performance behaviors. The two
+parameters of interest are the IOPS (Input/Output Operations per Second) and
+the bandwidth with which data can be written or read.
+
+A 'mirror' vdev (RAID1) will approximately behave like a single disk in regards
+to both parameters when writing data. When reading data if will behave like the
+number of disks in the mirror.
+
+A common situation is to have 4 disks. When setting it up as 2 mirror vdevs
+(RAID10) the pool will have the write characteristics as two single disks in
+regard of IOPS and bandwidth. For read operations it will resemble 4 single
+disks.
+
+A 'RAIDZ' of any redundancy level will approximately behave like a single disk
+in regard of IOPS with a lot of bandwidth. How much bandwidth depends on the
+size of the RAIDZ vdev and the redundancy level.
+
+For running VMs, IOPS is the more important metric in most situations.
+
+
+[[sysadmin_zfs_raid_size_space_usage_redundancy]]
+Size, Space usage and Redundancy
+^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
+
+While a pool made of 'mirror' vdevs will have the best performance
+characteristics, the usable space will be 50% of the disks available. Less if a
+mirror vdev consists of more than 2 disks, for example in a 3-way mirror. At
+least one healthy disk per mirror is needed for the pool to stay functional.
+
+The usable space of a 'RAIDZ' type vdev of N disks is roughly N-P, with P being
+the RAIDZ-level. The RAIDZ-level indicates how many arbitrary disks can fail
+without losing data. A special case is a 4 disk pool with RAIDZ2. In this
+situation it is usually better to use 2 mirror vdevs for the better performance
+as the usable space will be the same.
+
+Another important factor when using any RAIDZ level is how ZVOL datasets, which
+are used for VM disks, behave. For each data block the pool needs parity data
+which is at least the size of the minimum block size defined by the `ashift`
+value of the pool. With an ashift of 12 the block size of the pool is 4k.  The
+default block size for a ZVOL is 8k. Therefore, in a RAIDZ2 each 8k block
+written will cause two additional 4k parity blocks to be written,
+8k + 4k + 4k = 16k.  This is of course a simplified approach and the real
+situation will be slightly different with metadata, compression and such not
+being accounted for in this example.
+
+This behavior can be observed when checking the following properties of the
+ZVOL:
+
+ * `volsize`
+ * `refreservation` (if the pool is not thin provisioned)
+ * `used` (if the pool is thin provisioned and without snapshots present)
+
+----
+# zfs get volsize,refreservation,used <pool>/vm-<vmid>-disk-X
+----
+
+`volsize` is the size of the disk as it is presented to the VM, while
+`refreservation` shows the reserved space on the pool which includes the
+expected space needed for the parity data. If the pool is thin provisioned, the
+`refreservation` will be set to 0. Another way to observe the behavior is to
+compare the used disk space within the VM and the `used` property. Be aware
+that snapshots will skew the value.
+
+There are a few options to counter the increased use of space:
+
+* Increase the `volblocksize` to improve the data to parity ratio
+* Use 'mirror' vdevs instead of 'RAIDZ'
+* Use `ashift=9` (block size of 512 bytes)
+
+The `volblocksize` property can only be set when creating a ZVOL. The default
+value can be changed in the storage configuration. When doing this, the guest
+needs to be tuned accordingly and depending on the use case, the problem of
+write amplification if just moved from the ZFS layer up to the guest.
+
+Using `ashift=9` when creating the pool can lead to bad
+performance, depending on the disks underneath, and cannot be changed later on.
+
+Mirror vdevs (RAID1, RAID10) have favorable behavior for VM workloads. Use
+them, unless your environmanet has specific needs and charactersitics where
+RAIDZ performance characteristics are acceptable.
+
+
 Bootloader
 ~~~~~~~~~~