Open 2.0 development tree

[qemu.git] / docs / usb2.txt

diff --git a/docs/usb2.txt b/docs/usb2.txt
index d17e3c0044b176083b953bbc1b72ab9c0e8e0ee7..c7a445afcd55fe1f12033d529d668a1306d5a9f4 100644 (file)
--- a/docs/usb2.txt
+++ b/docs/usb2.txt
@@ -11,7 +11,7 @@ one USB 2.0 bus driven by the EHCI controller.  Devices must be
 attached to the correct controller manually.
 
 The '-usb' switch will make qemu create the UHCI controller as part of
-the PIIX3 chipset.  The USB 1.1 bus will carry the name "usb.0".
+the PIIX3 chipset.  The USB 1.1 bus will carry the name "usb-bus.0".
 
 You can use the standard -device switch to add a EHCI controller to
 your virtual machine.  It is strongly recommended to specify an ID for
@@ -27,7 +27,7 @@ a complete example:
         -drive if=none,id=usbstick,file=/path/to/image   \
         -usb                                             \
         -device usb-ehci,id=ehci                         \
-        -device usb-tablet,bus=usb.0                     \
+        -device usb-tablet,bus=usb-bus.0                 \
         -device usb-storage,bus=ehci.0,drive=usbstick
 
 This attaches a usb tablet to the UHCI adapter and a usb mass storage
@@ -58,11 +58,11 @@ try ...
 xhci controller support
 -----------------------
 
-There also is xhci host controller support available.  It got alot
+There is also xhci host controller support available.  It got a lot
 less testing than ehci and there are a bunch of known limitations, so
 ehci may work better for you.  On the other hand the xhci hardware
 design is much more virtualization-friendly, thus xhci emulation uses
-less ressources (especially cpu).  If you wanna give xhci a try
+less resources (especially cpu).  If you want to give xhci a try
 use this to add the host controller ...
 
     qemu -device nec-usb-xhci,id=xhci
@@ -88,22 +88,22 @@ ports (1-4), the emulated (1.1) USB hub has eight ports.
 
 Plugging a tablet into UHCI port 1 works like this:
 
-        -device usb-tablet,bus=usb.0,port=1
+        -device usb-tablet,bus=usb-bus.0,port=1
 
 Plugging a hub into UHCI port 2 works like this:
 
-        -device usb-hub,bus=usb.0,port=2
+        -device usb-hub,bus=usb-bus.0,port=2
 
 Plugging a virtual usb stick into port 4 of the hub just plugged works
 this way:
 
-        -device usb-storage,bus=usb.0,port=2.4,drive=...
+        -device usb-storage,bus=usb-bus.0,port=2.4,drive=...
 
 You can do basically the same in the monitor using the device_add
 command.  If you want to unplug devices too you should specify some
 unique id which you can use to refer to the device ...
 
-        (qemu) device_add usb-tablet,bus=usb.0,port=1,id=my-tablet
+        (qemu) device_add usb-tablet,bus=usb-bus.0,port=1,id=my-tablet
         (qemu) device_del my-tablet
 
 ... when unplugging it with device_del.
@@ -148,10 +148,10 @@ using for testing is bus 1 + port 1 for 2.0 devices and bus 3 + port 1
 for 1.1 devices.  Passing through any device plugged into that port
 and also assign them to the correct bus can be done this way:
 
-    qemu -M pc ${otheroptions}                           \
-        -usb                                             \
-        -device usb-ehci,id=ehci                         \
-        -device usb-host,bus=usb.0,hostbus=3,hostport=1  \
+    qemu -M pc ${otheroptions}                               \
+        -usb                                                 \
+        -device usb-ehci,id=ehci                             \
+        -device usb-host,bus=usb-bus.0,hostbus=3,hostport=1  \
         -device usb-host,bus=ehci.0,hostbus=1,hostport=1
 
 enjoy,