---- a/smartd.8.in
-+++ b/smartd.8.in
-@@ -554,10 +554,11 @@ Section below!
- .B # This is an example smartd startup config file
- .B # /usr/local/etc/smartd.conf for monitoring three
- .B # ATA disks, three SCSI disks, six ATA disks
--.B # behind two 3ware controllers, three SATA disks
--.B # directly connected to the HighPoint Rocket-
--.B # RAID controller, two SATA disks connected to
--.B # the HighPoint RocketRAID controller via a pmport
-+.B # behind two 3ware controllers, two disks on a cciss
-+.B # controller, three SATA disks directly connected
-+.B # to the HighPoint Rocket-RAID controller,
-+.B # two SATA disks connected to the HighPoint
-+.B # RocketRAID controller via a pmport
- .B # device, four SATA disks connected to an Areca
- .B # RAID controller, and one SATA disk.
- .B #
-@@ -619,6 +620,13 @@ Section below!
- .B \ \ /dev/twa0 -d 3ware,1 -a -s L/../../7/02
- .B #
- .nf
-+.B # Monitor 2 disks connected to the first HP SmartArray controller which
-+.B # uses the cciss driver. Start long tests on Sunday nights and short
-+.B # self-tests every night and send errors to root
-+.B \ \ /dev/cciss/c0d0 -d cciss,0 -a -s (L/../../7/02|S/../.././02) -m root
-+.B \ \ /dev/cciss/c0d0 -d cciss,1 -a -s (L/../../7/03|S/../.././03) -m root
-+.B #
-+.nf
- .B # Three SATA disks on a HighPoint RocketRAID controller.
- .B # Start short self-tests daily between 1-2, 2-3, and
- .B # 3-4 am.
-@@ -724,6 +732,10 @@ these disks. Areca firmware version 1.4
- smartmontools must be used; Please see the \fBsmartctl\fP(8) man page
- for further details.
-
-+.B If a cciss controller is used
-+then the corresponding block device (/dev/cciss/c?d?) must be listed,
-+along with the \'\-d cciss,N\' Directive (see below).
-+
- .TP
- .B \-d TYPE
- Specifies the type of the device. This Directive may be used multiple
-@@ -1255,9 +1267,9 @@ is set to the argument of \-M exec, if p
- .IP \fBSMARTD_DEVICE\fP 4
- is set to the device path (examples: /dev/hda, /dev/sdb).
- .IP \fBSMARTD_DEVICETYPE\fP 4
--is set to the device type (possible values: ata, scsi, 3ware,N,
-+is set to the device type (possible values: ata, scsi, 3ware,N, cciss,N,
- areca,N, hpt,L/M/N). Here N=0,...,127 denotes the ATA disk behind a
--3ware RAID controller and L/M/N denotes the SATA disk behind a
-+3ware or cciss RAID controller and L/M/N denotes the SATA disk behind a
- HighPoint RocketRAID controller.
- .IP \fBSMARTD_DEVICESTRING\fP 4
- is set to the device description. For SMARTD_DEVICETYPE of ata or