When do IPv6 tunnel PMTU update and calls __ip6_rt_update_pmtu() in the end,
we should not call dst_confirm_neigh() as there is no two-way communication.
Although GTP only support ipv4 right now, and __ip_rt_update_pmtu() does not
call dst_confirm_neigh(), we still set it to false to keep consistency with
IPv6 code.
v5: No change.
v4: No change.
v3: Do not remove dst_confirm_neigh, but add a new bool parameter in
dst_ops.update_pmtu to control whether we should do neighbor confirm.
Also split the big patch to small ones for each area.
v2: Remove dst_confirm_neigh in __ip6_rt_update_pmtu.
Reviewed-by: Guillaume Nault <gnault@redhat.com> Acked-by: David Ahern <dsahern@gmail.com> Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The MTU update code is supposed to be invoked in response to real
networking events that update the PMTU. In IPv6 PMTU update function
__ip6_rt_update_pmtu() we called dst_confirm_neigh() to update neighbor
confirmed time.
But for tunnel code, it will call pmtu before xmit, like:
- tnl_update_pmtu()
- skb_dst_update_pmtu()
- ip6_rt_update_pmtu()
- __ip6_rt_update_pmtu()
- dst_confirm_neigh()
If the tunnel remote dst mac address changed and we still do the neigh
confirm, we will not be able to update neigh cache and ping6 remote
will failed.
So for this ip_tunnel_xmit() case, _EVEN_ if the MTU is changed, we
should not be invoking dst_confirm_neigh() as we have no evidence
of successful two-way communication at this point.
On the other hand it is also important to keep the neigh reachability fresh
for TCP flows, so we cannot remove this dst_confirm_neigh() call.
To fix the issue, we have to add a new bool parameter for dst_ops.update_pmtu
to choose whether we should do neigh update or not. I will add the parameter
in this patch and set all the callers to true to comply with the previous
way, and fix the tunnel code one by one on later patches.
v5: No change.
v4: No change.
v3: Do not remove dst_confirm_neigh, but add a new bool parameter in
dst_ops.update_pmtu to control whether we should do neighbor confirm.
Also split the big patch to small ones for each area.
v2: Remove dst_confirm_neigh in __ip6_rt_update_pmtu.
Suggested-by: David Miller <davem@davemloft.net> Reviewed-by: Guillaume Nault <gnault@redhat.com> Acked-by: David Ahern <dsahern@gmail.com> Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When the size of the receive buffer for a socket is close to 2^31 when
computing if we have enough space in the buffer to copy a packet from
the queue to the buffer we might hit an integer overflow.
When an user set net.core.rmem_default to a value close to 2^31 UDP
packets are dropped because of this overflow. This can be visible, for
instance, with failure to resolve hostnames.
This can be fixed by casting sk_rcvbuf (which is an int) to unsigned
int, similarly to how it is done in TCP.
Signed-off-by: Antonio Messina <amessina@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In a case when a ptp chardev (like /dev/ptp0) is open but an underlying
device is removed, closing this file leads to a race. This reproduces
easily in a kvm virtual machine:
static void __fput(struct file *file)
{ ...
if (file->f_op->release)
file->f_op->release(inode, file); <<< cdev is kfree'd here
if (unlikely(S_ISCHR(inode->i_mode) && inode->i_cdev != NULL &&
!(mode & FMODE_PATH))) {
cdev_put(inode->i_cdev); <<< cdev fields are accessed here
Namely:
__fput()
posix_clock_release()
kref_put(&clk->kref, delete_clock) <<< the last reference
delete_clock()
delete_ptp_clock()
kfree(ptp) <<< cdev is embedded in ptp
cdev_put
module_put(p->owner) <<< *p is kfree'd, bang!
Here cdev is embedded in posix_clock which is embedded in ptp_clock.
The race happens because ptp_clock's lifetime is controlled by two
refcounts: kref and cdev.kobj in posix_clock. This is wrong.
Make ptp_clock's sysfs device a parent of cdev with cdev_device_add()
created especially for such cases. This way the parent device with its
ptp_clock is not released until all references to the cdev are released.
This adds a requirement that an initialized but not exposed struct
device should be provided to posix_clock_register() by a caller instead
of a simple dev_t.
This approach was adopted from the commit 72139dfa2464 ("watchdog: Fix
the race between the release of watchdog_core_data and cdev"). See
details of the implementation in the commit 233ed09d7fda ("chardev: add
helper function to register char devs with a struct device").
Link: https://lore.kernel.org/linux-fsdevel/20191125125342.6189-1-vdronov@redhat.com/T/#u Analyzed-by: Stephen Johnston <sjohnsto@redhat.com> Analyzed-by: Vern Lovejoy <vlovejoy@redhat.com> Signed-off-by: Vladis Dronov <vdronov@redhat.com> Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The burning process requires to perform internal allocations of large
chunks of memory. This memory doesn't need to be contiguous and can be
safely allocated by vzalloc() instead of kzalloc(). This patch changes
such allocation to avoid possible out-of-memory failure.
Fixes: 410ed13cae39 ("Add the mlxfw module for Mellanox firmware flash process") Signed-off-by: Vladyslav Tarasiuk <vladyslavt@mellanox.com> Reviewed-by: Aya Levin <ayal@mellanox.com> Signed-off-by: Leon Romanovsky <leonro@mellanox.com> Tested-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In netpoll the napi handler could be called with budget equal to zero.
Current ENA napi handler doesn't take that into consideration.
The napi handler handles Rx packets in a do-while loop.
Currently, the budget check happens only after decrementing the
budget, therefore the napi handler, in rare cases, could run over
MAX_INT packets.
In addition to that, this moves all budget related variables to int
calculation and stop mixing u32 to avoid ambiguity
Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)") Signed-off-by: Netanel Belgazal <netanel@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Commit 39ce8150a079 ("pinctrl: baytrail: Serialize all register access")
added a spinlock around all register accesses because:
"There is a hardware issue in Intel Baytrail where concurrent GPIO register
access might result reads of 0xffffffff and writes might get dropped
completely."
Testing has shown that this does not catch all cases, there are still
2 problems remaining
1) The original fix uses a spinlock per byt_gpio device / struct,
additional testing has shown that this is not sufficient concurent
accesses to 2 different GPIO banks also suffer from the same problem.
This commit fixes this by moving to a single global lock.
2) The original fix did not add a lock around the register accesses in
the suspend/resume handling.
Since pinctrl-baytrail.c is using normal suspend/resume handlers,
interrupts are still enabled during suspend/resume handling. Nothing
should be using the GPIOs when they are being taken down, _but_ the
GPIOs themselves may still cause interrupts, which are likely to
use (read) the triggering GPIO. So we need to protect against
concurrent GPIO register accesses in the suspend/resume handlers too.
This commit fixes this by adding the missing spin_lock / unlock calls.
The 2 fixes together fix the Acer Switch 10 SW5-012 getting completely
confused after a suspend resume. The DSDT for this device has a bug
in its _LID method which reprograms the home and power button trigger-
flags requesting both high and low _level_ interrupts so the IRQs for
these 2 GPIOs continuously fire. This combined with the saving of
registers during suspend, triggers concurrent GPIO register accesses
resulting in saving 0xffffffff as pconf0 value during suspend and then
when restoring this on resume the pinmux settings get all messed up,
resulting in various I2C busses being stuck, the wifi no longer working
and often the tablet simply not coming out of suspend at all.
Cc: stable@vger.kernel.org Fixes: 39ce8150a079 ("pinctrl: baytrail: Serialize all register access") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The problem comes from the error path which calls
irq_dispose_mapping() while the IRQ has been requested with
devm_request_irq().
IRQ doesn't need to be mapped with irq_of_parse_and_map(). The only
need is to get the IRQ virtual number. For that, use
of_irq_to_resource() instead of the
irq_of_parse_and_map()/irq_dispose_mapping() pair.
Fixes: 500a32abaf81 ("spi: fsl: Call irq_dispose_mapping in err path") Cc: stable@vger.kernel.org Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr> Link: https://lore.kernel.org/r/518cfb83347d5372748e7fe72f94e2e9443d0d4a.1575905123.git.christophe.leroy@c-s.fr Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 24652 Comm: syz-executor.3 Not tainted 5.4.0-rc3+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
[ tglx: Added comments ]
Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lkml.kernel.org/r/20191106174804.74723-1-edumazet@google.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This code reads two global variables without protection
of a lock. We need READ_ONCE()/WRITE_ONCE() pairs to
avoid load/store-tearing and better document the intent.
KCSAN reported :
BUG: KCSAN: data-race in icmp_global_allow / icmp_global_allow
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 11183 Comm: syz-executor.2 Not tainted 5.4.0-rc3+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Fixes: 4cdf507d5452 ("icmp: add a global rate limitation") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
skb_peek_tail() can be used without protection of a lock,
as spotted by KCSAN [1]
In order to avoid load-stearing, add a READ_ONCE()
Note that the corresponding WRITE_ONCE() are already there.
[1]
BUG: KCSAN: data-race in sk_wait_data / skb_queue_tail
read to 0xffff8880b36a4118 of 8 bytes by task 20426 on cpu 1:
skb_peek_tail include/linux/skbuff.h:1784 [inline]
sk_wait_data+0x15b/0x250 net/core/sock.c:2477
kcm_wait_data+0x112/0x1f0 net/kcm/kcmsock.c:1103
kcm_recvmsg+0xac/0x320 net/kcm/kcmsock.c:1130
sock_recvmsg_nosec net/socket.c:871 [inline]
sock_recvmsg net/socket.c:889 [inline]
sock_recvmsg+0x92/0xb0 net/socket.c:885
___sys_recvmsg+0x1a0/0x3e0 net/socket.c:2480
do_recvmmsg+0x19a/0x5c0 net/socket.c:2601
__sys_recvmmsg+0x1ef/0x200 net/socket.c:2680
__do_sys_recvmmsg net/socket.c:2703 [inline]
__se_sys_recvmmsg net/socket.c:2696 [inline]
__x64_sys_recvmmsg+0x89/0xb0 net/socket.c:2696
do_syscall_64+0xcc/0x370 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x44/0xa9
write to 0xffff8880b36a4118 of 8 bytes by task 451 on cpu 0:
__skb_insert include/linux/skbuff.h:1852 [inline]
__skb_queue_before include/linux/skbuff.h:1958 [inline]
__skb_queue_tail include/linux/skbuff.h:1991 [inline]
skb_queue_tail+0x7e/0xc0 net/core/skbuff.c:3145
kcm_queue_rcv_skb+0x202/0x310 net/kcm/kcmsock.c:206
kcm_rcv_strparser+0x74/0x4b0 net/kcm/kcmsock.c:370
__strp_recv+0x348/0xf50 net/strparser/strparser.c:309
strp_recv+0x84/0xa0 net/strparser/strparser.c:343
tcp_read_sock+0x174/0x5c0 net/ipv4/tcp.c:1639
strp_read_sock+0xd4/0x140 net/strparser/strparser.c:366
do_strp_work net/strparser/strparser.c:414 [inline]
strp_work+0x9a/0xe0 net/strparser/strparser.c:423
process_one_work+0x3d4/0x890 kernel/workqueue.c:2269
worker_thread+0xa0/0x800 kernel/workqueue.c:2415
kthread+0x1d4/0x200 drivers/block/aoe/aoecmd.c:1253
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:352
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 451 Comm: kworker/u4:3 Not tainted 5.4.0-rc3+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: kstrp strp_work
Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
write to 0xffff888121fb2ed0 of 4 bytes by interrupt on cpu 1:
inet_putpeer+0x37/0xa0 net/ipv4/inetpeer.c:240
ip4_frag_free+0x3d/0x50 net/ipv4/ip_fragment.c:102
inet_frag_destroy_rcu+0x58/0x80 net/ipv4/inet_fragment.c:228
__rcu_reclaim kernel/rcu/rcu.h:222 [inline]
rcu_do_batch+0x256/0x5b0 kernel/rcu/tree.c:2157
rcu_core+0x369/0x4d0 kernel/rcu/tree.c:2377
rcu_core_si+0x12/0x20 kernel/rcu/tree.c:2386
__do_softirq+0x115/0x33f kernel/softirq.c:292
run_ksoftirqd+0x46/0x60 kernel/softirq.c:603
smpboot_thread_fn+0x37d/0x4a0 kernel/smpboot.c:165
kthread+0x1d4/0x200 drivers/block/aoe/aoecmd.c:1253
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:352
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 16 Comm: ksoftirqd/1 Not tainted 5.4.0-rc3+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Fixes: 4b9d9be839fd ("inetpeer: remove unused list") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
BUG: KASAN: vmalloc-out-of-bounds in size_entry_mwt net/bridge/netfilter/ebtables.c:2063 [inline]
BUG: KASAN: vmalloc-out-of-bounds in compat_copy_entries+0x128b/0x1380 net/bridge/netfilter/ebtables.c:2155
Read of size 4 at addr ffffc900004461f4 by task syz-executor267/7937
Because padding isn't considered during computation of ->buf_user_offset,
"total" is decremented by fewer bytes than it should.
Therefore, the first part of
if (*total < sizeof(*entry) || entry->next_offset < sizeof(*entry))
will pass, -- it should not have. This causes oob access:
entry->next_offset is past the vmalloced size.
Reject padding and check that computed user offset (sum of ebt_entry
structure plus all individual matches/watchers/targets) is same
value that userspace gave us as the offset of the next entry.
This was always meant to be a temporary thing, just for testing and to
see if it actually ever triggered.
The only thing that reported it was syzbot doing disk image fuzzing, and
then that warning is expected. So let's just remove it before -rc4,
because the extra sanity testing should probably go to -stable, but we
don't want the warning to do so.
This has been discussed several times, and now filesystem people are
talking about doing it individually at the filesystem layer, so head
that off at the pass and just do it in getdents{64}().
This is partially based on a patch by Jann Horn, but checks for NUL
bytes as well, and somewhat simplified.
There's also commentary about how it might be better if invalid names
due to filesystem corruption don't cause an immediate failure, but only
an error at the end of the readdir(), so that people can still see the
filenames that are ok.
There's also been discussion about just how much POSIX strictly speaking
requires this since it's about filesystem corruption. It's really more
"protect user space from bad behavior" as pointed out by Jann. But
since Eric Biederman looked up the POSIX wording, here it is for context:
"From readdir:
The readdir() function shall return a pointer to a structure
representing the directory entry at the current position in the
directory stream specified by the argument dirp, and position the
directory stream at the next entry. It shall return a null pointer
upon reaching the end of the directory stream. The structure dirent
defined in the <dirent.h> header describes a directory entry.
From definitions:
3.129 Directory Entry (or Link)
An object that associates a filename with a file. Several directory
entries can associate names with the same file.
...
3.169 Filename
A name consisting of 1 to {NAME_MAX} bytes used to name a file. The
characters composing the name may be selected from the set of all
character values excluding the slash character and the null byte. The
filenames dot and dot-dot have special meaning. A filename is
sometimes referred to as a 'pathname component'."
Note that I didn't bother adding the checks to any legacy interfaces
that nobody uses.
Also note that if this ends up being noticeable as a performance
regression, we can fix that to do a much more optimized model that
checks for both NUL and '/' at the same time one word at a time.
We haven't really tended to optimize 'memchr()', and it only checks for
one pattern at a time anyway, and we really _should_ check for NUL too
(but see the comment about "soft errors" in the code about why it
currently only checks for '/')
See the CONFIG_DCACHE_WORD_ACCESS case of hash_name() for how the name
lookup code looks for pathname terminating characters in parallel.
Link: https://lore.kernel.org/lkml/20190118161440.220134-2-jannh@google.com/ Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Jann Horn <jannh@google.com> Cc: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Siddharth Chandrasekaran <csiddharth@vmware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Each call to va_copy() should have one, and only one, corresponding call
to va_end(). In strbuf_addv() some code paths result in va_end() getting
called multiple times. Remove the superfluous va_end().
Signed-off-by: Mattias Jacobsson <2pi@mok.nu> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Sanskriti Sharma <sansharm@redhat.com> Link: http://lkml.kernel.org/r/20181229141750.16945-1-2pi@mok.nu Fixes: ce49d8436cff ("perf strbuf: Match va_{add,copy} with va_end") Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
After the recent fix in commit 1899bb325149 ("bonding: fix state
transition issue in link monitoring"), the active-backup mode with
miimon initially come-up fine but after a link-failure, both members
transition into backup state.
Following steps to reproduce the scenario (eth1 and eth2 are the
slaves of the bond):
ip link set eth1 up
ip link set eth2 down
sleep 1
ip link set eth2 up
ip link set eth1 down
cat /sys/class/net/eth1/bonding_slave/state
cat /sys/class/net/eth2/bonding_slave/state
Fixes: 1899bb325149 ("bonding: fix state transition issue in link monitoring") CC: Jay Vosburgh <jay.vosburgh@canonical.com> Signed-off-by: Mahesh Bandewar <maheshb@google.com> Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
We made the error message for the CORB/RIRB communication clearer by
upgrading to dev_WARN() so that user can notice better. But this
struck us like a boomerang: now it caught syzbot and reported back as
a fatal issue although it's not really any too serious bug that worth
for stopping the whole system.
OK, OK, let's be softy, downgrade it to the standard dev_err() again.
Fixes: dd65f7e19c69 ("ALSA: hda - Show the fatal CORB/RIRB error more clearly") Reported-by: syzbot+b3028ac3933f5c466389@syzkaller.appspotmail.com Link: https://lore.kernel.org/r/20191216151224.30013-1-tiwai@suse.de Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Bridge packets that are forwarded have skb->dst == NULL and get
dropped by the check introduced by b60a77386b1d4868f72f6353d35dabe5fbe981f2 (net: make skb_dst_force
return true when dst is refcounted).
To fix this we check skb_dst() before skb_dst_force(), so we don't
drop skb packet with dst == NULL. This holds also for skb at the
PRE_ROUTING hook so we remove the second check.
Fixes: b60a77386b1d ("net: make skb_dst_force return true when dst is refcounted") Signed-off-by: Marco Oliverio <marco.oliverio@tanaza.com> Signed-off-by: Rocco Folino <rocco.folino@tanaza.com> Acked-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
proc_dointvec_minmax_bpf_restricted() has been firstly introduced
in commit 2e4a30983b0f ("bpf: restrict access to core bpf sysctls")
under CONFIG_HAVE_EBPF_JIT. Then, this ifdef has been removed in ede95a63b5e8 ("bpf: add bpf_jit_limit knob to restrict unpriv
allocations"), because a new sysctl, bpf_jit_limit, made use of it.
Finally, this parameter has become long instead of integer with fdadd04931c2 ("bpf: fix bpf_jit_limit knob for PAGE_SIZE >= 64K")
and thus, a new proc_dolongvec_minmax_bpf_restricted() has been
added.
With this last change, we got back to that
proc_dointvec_minmax_bpf_restricted() is used only under
CONFIG_HAVE_EBPF_JIT, but the corresponding ifdef has not been
brought back.
So, in configurations like CONFIG_BPF_JIT=y && CONFIG_HAVE_EBPF_JIT=n
since v4.20 we have:
CC net/core/sysctl_net_core.o
net/core/sysctl_net_core.c:292:1: warning: ‘proc_dointvec_minmax_bpf_restricted’ defined but not used [-Wunused-function]
292 | proc_dointvec_minmax_bpf_restricted(struct ctl_table *table, int write,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Suppress this by guarding it with CONFIG_HAVE_EBPF_JIT again.
Fixes: fdadd04931c2 ("bpf: fix bpf_jit_limit knob for PAGE_SIZE >= 64K") Signed-off-by: Alexander Lobakin <alobakin@dlink.ru> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Link: https://lore.kernel.org/bpf/20191218091821.7080-1-alobakin@dlink.ru Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The function mce_severity_amd_smca() requires m->bank to be initialized
for correct operation. Fix the one case, where mce_severity() is called
without doing so.
Fixes: 6bda529ec42e ("x86/mce: Grade uncorrected errors for SMCA-enabled systems") Fixes: d28af26faa0b ("x86/MCE: Initialize mce.bank in the case of a fatal error in mce_no_way_out()") Signed-off-by: Jan H. Schönherr <jschoenh@amazon.de> Signed-off-by: Borislav Petkov <bp@suse.de> Reviewed-by: Tony Luck <tony.luck@intel.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: linux-edac <linux-edac@vger.kernel.org> Cc: <stable@vger.kernel.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: x86-ml <x86@kernel.org> Cc: Yazen Ghannam <Yazen.Ghannam@amd.com> Link: https://lkml.kernel.org/r/20191210000733.17979-4-jschoenh@amazon.de Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
A while ago Andy noticed
(http://lkml.kernel.org/r/CALCETrWY+5ynDct7eU_nDUqx=okQvjm=Y5wJvA4ahBja=CQXGw@mail.gmail.com)
that UFFD_FEATURE_EVENT_FORK used by an unprivileged user may have
security implications.
As the first step of the solution the following patch limits the availably
of UFFD_FEATURE_EVENT_FORK only for those having CAP_SYS_PTRACE.
The usage of CAP_SYS_PTRACE ensures compatibility with CRIU.
Yet, if there are other users of non-cooperative userfaultfd that run
without CAP_SYS_PTRACE, they would be broken :(
Current implementation of UFFD_FEATURE_EVENT_FORK modifies the file
descriptor table from the read() implementation of uffd, which may have
security implications for unprivileged use of the userfaultfd.
Limit availability of UFFD_FEATURE_EVENT_FORK only for callers that have
CAP_SYS_PTRACE.
Link: http://lkml.kernel.org/r/1572967777-8812-2-git-send-email-rppt@linux.ibm.com Signed-off-by: Mike Rapoport <rppt@linux.ibm.com> Reviewed-by: Andrea Arcangeli <aarcange@redhat.com> Cc: Daniel Colascione <dancol@google.com> Cc: Jann Horn <jannh@google.com> Cc: Lokesh Gidra <lokeshgidra@google.com> Cc: Nick Kralevich <nnk@google.com> Cc: Nosh Minwalla <nosh@google.com> Cc: Pavel Emelyanov <ovzxemul@gmail.com> Cc: Tim Murray <timmurray@google.com> Cc: Aleksa Sarai <cyphar@cyphar.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Currently, the drop_caches proc file and sysctl read back the last value
written, suggesting this is somehow a stateful setting instead of a
one-time command. Make it write-only, like e.g. compact_memory.
While mitigating a VM problem at scale in our fleet, there was confusion
about whether writing to this file will permanently switch the kernel into
a non-caching mode. This influences the decision making in a tense
situation, where tens of people are trying to fix tens of thousands of
affected machines: Do we need a rollback strategy? What are the
performance implications of operating in a non-caching state for several
days? It also caused confusion when the kernel team said we may need to
write the file several times to make sure it's effective ("But it already
reads back 3?").
Link: http://lkml.kernel.org/r/20191031221602.9375-1-hannes@cmpxchg.org Signed-off-by: Johannes Weiner <hannes@cmpxchg.org> Acked-by: Chris Down <chris@chrisdown.name> Acked-by: Vlastimil Babka <vbabka@suse.cz> Acked-by: David Hildenbrand <david@redhat.com> Acked-by: Michal Hocko <mhocko@suse.com> Acked-by: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Each SBDT is located at a 4KB page and contains 512 entries.
Each entry of a SDBT points to a SDB, a 4KB page containing
sampled data. The last entry is a link to another SDBT page.
When an event is created the function sequence executed is:
Both functions realloc_sampling_buffers() and
alloc_sample_data_block() allocate pages and the allocation
can fail. This is handled correctly and all allocated
pages are freed and error -ENOMEM is returned to the
top calling function. Finally the event is not created.
Once the event has been created, the amount of initially
allocated SDBT and SDB can be too low. This is detected
during measurement interrupt handling, where the amount
of lost samples is calculated. If the number of lost samples
is too high considering sampling frequency and already allocated
SBDs, the number of SDBs is enlarged during the next execution
of cpumsf_pmu_enable().
are called to allocate more pages. Page allocation may fail
and the returned error is ignored. A SDBT and SDB setup
already exists.
However the modified SDBTs and SDBs might end up in a situation
where the first entry of an SDBT does not point to an SDB,
but another SDBT, basicly an SBDT without payload.
This can not be handled by the interrupt handler, where an SDBT
must have at least one entry pointing to an SBD.
Add a check to avoid SDBTs with out payload (SDBs) when enlarging
the buffer setup.
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This patch introduces support for a new architectured reply
code 0x8B indicating that a hypervisor layer (if any) has
rejected an ap message.
Linux may run as a guest on top of a hypervisor like zVM
or KVM. So the crypto hardware seen by the ap bus may be
restricted by the hypervisor for example only a subset like
only clear key crypto requests may be supported. Other
requests will be filtered out - rejected by the hypervisor.
The new reply code 0x8B will appear in such cases and needs
to get recognized by the ap bus and zcrypt device driver zoo.
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
To avoid breaking the build on arches where this is not wired up, at
least all the other features should be made available and when using
this specific routine, the "unknown" should point the user/developer to
the need to wire this up on this particular hardware architecture.
Detected in a container mipsel debian cross build environment, where it
shows up as:
In file included from /usr/mipsel-linux-gnu/include/stdio.h:867,
from /git/linux/tools/perf/lib/include/perf/cpumap.h:6,
from util/session.c:13:
In function 'printf',
inlined from 'regs_dump__printf' at util/session.c:1103:3,
inlined from 'regs__printf' at util/session.c:1131:2:
/usr/mipsel-linux-gnu/include/bits/stdio2.h:107:10: error: '%-5s' directive argument is null [-Werror=format-overflow=]
107 | return __printf_chk (__USE_FORTIFY_LEVEL - 1, __fmt, __va_arg_pack ());
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from /usr/mips64-linux-gnuabi64/include/stdio.h:867,
from /git/linux/tools/perf/lib/include/perf/cpumap.h:6,
from util/session.c:13:
In function 'printf',
inlined from 'regs_dump__printf' at util/session.c:1103:3,
inlined from 'regs__printf' at util/session.c:1131:2,
inlined from 'regs_user__printf' at util/session.c:1139:3,
inlined from 'dump_sample' at util/session.c:1246:3,
inlined from 'machines__deliver_event' at util/session.c:1421:3:
/usr/mips64-linux-gnuabi64/include/bits/stdio2.h:107:10: error: '%-5s' directive argument is null [-Werror=format-overflow=]
107 | return __printf_chk (__USE_FORTIFY_LEVEL - 1, __fmt, __va_arg_pack ());
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
In function 'printf',
inlined from 'regs_dump__printf' at util/session.c:1103:3,
inlined from 'regs__printf' at util/session.c:1131:2,
inlined from 'regs_intr__printf' at util/session.c:1147:3,
inlined from 'dump_sample' at util/session.c:1249:3,
inlined from 'machines__deliver_event' at util/session.c:1421:3:
/usr/mips64-linux-gnuabi64/include/bits/stdio2.h:107:10: error: '%-5s' directive argument is null [-Werror=format-overflow=]
107 | return __printf_chk (__USE_FORTIFY_LEVEL - 1, __fmt, __va_arg_pack ());
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
brstackinsn must be allowed to be set by the user when AUX area data has
been captured because, in that case, the branch stack might be
synthesized on the fly. This fixes the following error:
Before:
$ perf record -e '{intel_pt//,cpu/mem_inst_retired.all_loads,aux-sample-size=8192/pp}:u' grep -rqs jhgjhg /boot
[ perf record: Woken up 19 times to write data ]
[ perf record: Captured and wrote 2.274 MB perf.data ]
$ perf script -F +brstackinsn --xed --itrace=i1usl100 | head
Display of branch stack assembler requested, but non all-branch filter set
Hint: run 'perf record -b ...'
After:
$ perf record -e '{intel_pt//,cpu/mem_inst_retired.all_loads,aux-sample-size=8192/pp}:u' grep -rqs jhgjhg /boot
[ perf record: Woken up 19 times to write data ]
[ perf record: Captured and wrote 2.274 MB perf.data ]
$ perf script -F +brstackinsn --xed --itrace=i1usl100 | head
grep 13759 [002] 8091.310257: 1862 instructions:uH: 5641d58069eb bmexec+0x86b (/bin/grep)
bmexec+2485: 00005641d5806b35 jnz 0x5641d5806bd0 # MISPRED 00005641d5806bd0 movzxb (%r13,%rdx,1), %eax 00005641d5806bd6 add %rdi, %rax 00005641d5806bd9 movzxb -0x1(%rax), %edx 00005641d5806bdd cmp %rax, %r14 00005641d5806be0 jnb 0x5641d58069c0 # MISPRED
mismatch of LBR data and executable 00005641d58069c0 movzxb (%r13,%rdx,1), %edi
Fixes: 48d02a1d5c13 ("perf script: Add 'brstackinsn' for branch stacks") Reported-by: Andi Kleen <ak@linux.intel.com> Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Link: http://lore.kernel.org/lkml/20191127095322.15417-1-adrian.hunter@intel.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
build_initial_tok_table() overwrites unused sym_entry to shrink the
table size. Before the entry is overwritten, table[i].sym must be freed
since it is malloc'ed data.
This fixes the 'definitely lost' report from valgrind. I ran valgrind
against x86_64_defconfig of v5.4-rc8 kernel, and here is the summary:
[Before the fix]
LEAK SUMMARY:
definitely lost: 53,184 bytes in 2,874 blocks
[After the fix]
LEAK SUMMARY:
definitely lost: 0 bytes in 0 blocks
The sanity check in macro update_for_len checks to see if len
is less than zero, however, len is a size_t so it can never be
less than zero, so this sanity check is a no-op. Fix this by
making len a ssize_t so the comparison will work and add ulen
that is a size_t copy of len so that the min() macro won't
throw warnings about comparing different types.
Addresses-Coverity: ("Macro compares unsigned to 0") Fixes: f1bd904175e8 ("apparmor: add the base fns() for domain labels") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: John Johansen <john.johansen@canonical.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The per-SoC devtype structures can contain their own callbacks that
overwrite mpc8xxx_gpio_devtype_default.
The clear intention is that mpc8xxx_irq_set_type is used in case the SoC
does not specify a more specific callback. But what happens is that if
the SoC doesn't specify one, its .irq_set_type is de-facto NULL, and
this overwrites mpc8xxx_irq_set_type to a no-op. This means that the
following SoCs are affected:
On these boards, the irq_set_type does exactly nothing, and the GPIO
controller keeps its GPICR register in the hardware-default state. On
the LS1028A, that is ACTIVE_BOTH, which means 2 interrupts are raised
even if the IRQ client requests LEVEL_HIGH. Another implication is that
the IRQs are not checked (e.g. level-triggered interrupts are not
rejected, although they are not supported).
Fixes: 82e39b0d8566 ("gpio: mpc8xxx: handle differences between incarnations at a single place") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Link: https://lore.kernel.org/r/20191115125551.31061-1-olteanv@gmail.com Tested-by: Michael Walle <michael@walle.cc> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The iSCSI target driver is the only target driver that does not wait for
ongoing commands to finish before freeing a session. Make the iSCSI target
driver wait for ongoing commands to finish before freeing a session. This
patch fixes the following KASAN complaint:
BUG: KASAN: use-after-free in __lock_acquire+0xb1a/0x2710
Read of size 8 at addr ffff8881154eca70 by task kworker/0:2/247
Memory state around the buggy address: ffff8881154ec900: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff8881154ec980: fc fc fc fc fc fc fc fc fb fb fb fb fb fb fb fb
>ffff8881154eca00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^ ffff8881154eca80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff8881154ecb00: fb fb fb fb fc fc fc fc fc fc fc fc fc fc fc fc
Cc: Mike Christie <mchristi@redhat.com> Link: https://lore.kernel.org/r/20191113220508.198257-3-bvanassche@acm.org Reviewed-by: Roman Bolshakov <r.bolshakov@yadro.com> Signed-off-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If a faulty initiator fails to bind the socket to the iSCSI connection
before emitting a command, for instance, a subsequent send_pdu, it will
crash the kernel due to a null pointer dereference in sock_sendmsg(), as
shown in the log below. This patch makes sure the bind succeeded before
trying to use the socket.
Add a module parameter to inhibit disconnect/reselect for individual
targets. This gains compatibility with Aztec PowerMonster SCSI/SATA
adapters with buggy firmware. (No fix is available from the vendor.)
Apparently these adapters pass-through the product/vendor of the attached
SATA device. Since they can't be identified from the response to an INQUIRY
command, a device blacklist flag won't work.
Cc: Michael Schmitz <schmitzmic@gmail.com> Link: https://lore.kernel.org/r/993b17545990f31f9fa5a98202b51102a68e7594.1573875417.git.fthain@telegraphics.com.au Reviewed-and-tested-by: Michael Schmitz <schmitzmic@gmail.com> Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
During clock gating (ufshcd_gate_work()), we first put the link hibern8 by
calling ufshcd_uic_hibern8_enter() and if ufshcd_uic_hibern8_enter()
returns success (0) then we gate all the clocks. Now let’s zoom in to what
ufshcd_uic_hibern8_enter() does internally: It calls
__ufshcd_uic_hibern8_enter() and if failure is encountered, link recovery
shall put the link back to the highest HS gear and returns success (0) to
ufshcd_uic_hibern8_enter() which is the issue as link is still in active
state due to recovery! Now ufshcd_uic_hibern8_enter() returns success to
ufshcd_gate_work() and hence it goes ahead with gating the UFS clock while
link is still in active state hence I believe controller would raise UIC
error interrupts. But when we service the interrupt, clocks might have
already been disabled!
This change fixes for this by returning failure from
__ufshcd_uic_hibern8_enter() if recovery succeeds as link is still not in
hibern8, upon receiving the error ufshcd_hibern8_enter() would initiate
retry to put the link state back into hibern8.
Link: https://lore.kernel.org/r/1573798172-20534-8-git-send-email-cang@codeaurora.org Reviewed-by: Avri Altman <avri.altman@wdc.com> Reviewed-by: Bean Huo <beanhuo@micron.com> Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org> Signed-off-by: Can Guo <cang@codeaurora.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Driver was missing complete() call in mpi_sata_completion which result in
SATA abort error handling timing out. That causes the device to be left in
the in_recovery state so subsequent commands sent to the device fail and
the OS removes access to it.
Link: https://lore.kernel.org/r/20191114100910.6153-2-deepak.ukey@microchip.com Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com> Signed-off-by: peter chang <dpf@google.com> Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com> Signed-off-by: Viswas G <Viswas.G@microchip.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
However, some devices, namely Microsoft's Surface line of products
instead implement a "segmented device certification report" (usage 0xC6)
which returns the same report, but in smaller chunks.
drivers/nvdimm/btt.c: In function 'btt_read_pg':
drivers/nvdimm/btt.c:1264:8: warning: variable 'rc' set but not used
[-Wunused-but-set-variable]
int rc;
^~
Add a ratelimited message in case a storm of errors is encountered.
Fixes: d9b83c756953 ("libnvdimm, btt: rework error clearing") Signed-off-by: Qian Cai <cai@lca.pw> Reviewed-by: Vishal Verma <vishal.l.verma@intel.com> Link: https://lore.kernel.org/r/1572530719-32161-1-git-send-email-cai@lca.pw Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
My Logitech M185 (PID:4038) 2.4 GHz wireless HID++ mouse is causing
intermittent errors like these in the log:
[11091.034857] logitech-hidpp-device 0003:046D:4038.0006: hidpp20_batterylevel_get_battery_capacity: received protocol error 0x09
[12388.031260] logitech-hidpp-device 0003:046D:4038.0006: hidpp20_batterylevel_get_battery_capacity: received protocol error 0x09
[16613.718543] logitech-hidpp-device 0003:046D:4038.0006: hidpp20_batterylevel_get_battery_capacity: received protocol error 0x09
[23529.938728] logitech-hidpp-device 0003:046D:4038.0006: hidpp20_batterylevel_get_battery_capacity: received protocol error 0x09
We are already silencing error-code 0x09 (HIDPP_ERROR_RESOURCE_ERROR)
errors in other places, lets do the same in
hidpp20_batterylevel_get_battery_capacity to remove these harmless,
but scary looking errors from the dmesg output.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In bch_mca_scan(), the number of shrinking btree node is calculated
by code like this,
unsigned long nr = sc->nr_to_scan;
nr /= c->btree_pages;
nr = min_t(unsigned long, nr, mca_can_free(c));
variable sc->nr_to_scan is number of objects (here is bcache B+tree
nodes' number) to shrink, and pointer variable sc is sent from memory
management code as parametr of a callback.
If sc->nr_to_scan is smaller than c->btree_pages, after the above
calculation, variable 'nr' will be 0 and nothing will be shrunk. It is
frequeently observed that only 1 or 2 is set to sc->nr_to_scan and make
nr to be zero. Then bch_mca_scan() will do nothing more then acquiring
and releasing mutex c->bucket_lock.
This patch checkes whether nr is 0 after the above calculation, if 0
is the result then set 1 to variable 'n'. Then at least bch_mca_scan()
will try to shrink a single B+tree node.
Signed-off-by: Coly Li <colyli@suse.de> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Link: https://lore.kernel.org/r/4567bcae94523b47d6f3b77450ba305823bca479.1572656814.git.fthain@telegraphics.com.au Reported-and-tested-by: Michael Schmitz <schmitzmic@gmail.com> Reviewed-by: Michael Schmitz <schmitzmic@gmail.com>
References: commit 68ab2d76e4be ("scsi: cxlflash: Set sg_tablesize to 1 instead of SG_NONE") Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Output before this fix:
# cat /sys/devices/system/cpu/vulnerabilities/meltdown
Mitigation: RFI Flush, L1D private per thread
# echo 0 > /sys/kernel/debug/powerpc/rfi_flush
# cat /sys/devices/system/cpu/vulnerabilities/meltdown
Mitigation: L1D private per thread
Output after fix:
# cat /sys/devices/system/cpu/vulnerabilities/meltdown
Mitigation: RFI Flush, L1D private per thread
# echo 0 > /sys/kernel/debug/powerpc/rfi_flush
# cat /sys/devices/system/cpu/vulnerabilities/meltdown
Vulnerable: L1D private per thread
Signed-off-by: Gustavo L. F. Walbon <gwalbon@linux.ibm.com> Signed-off-by: Mauro S. M. Rodrigues <maurosr@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20190502210907.42375-1-gwalbon@linux.ibm.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When unloading the module, one gets
------------[ cut here ]------------
Device 'cmm0' does not have a release() function, it is broken and must be fixed. See Documentation/kobject.txt.
WARNING: CPU: 0 PID: 19308 at drivers/base/core.c:1244 .device_release+0xcc/0xf0
...
We only have one static fake device. There is nothing to do when
releasing the device (via cmm_exit()).
Signed-off-by: David Hildenbrand <david@redhat.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20191031142933.10779-2-david@redhat.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In function __ufshcd_query_descriptor(), in the event of an error
happening, we directly goto out_unlock and forget to invaliate
hba->dev_cmd.query.descriptor pointer. This results in this pointer still
valid in ufshcd_copy_query_response() for other query requests which go
through ufshcd_exec_raw_upiu_cmd(). This will cause __memcpy() crash and
system hangs. Log as shown below:
Unable to handle kernel paging request at virtual address ffff000012233c40
Mem abort info:
ESR = 0x96000047
Exception class = DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
Data abort info:
ISV = 0, ISS = 0x00000047
CM = 0, WnR = 1
swapper pgtable: 4k pages, 48-bit VAs, pgdp = 0000000028cc735c
[ffff000012233c40] pgd=00000000bffff003, pud=00000000bfffe003,
pmd=00000000ba8b8003, pte=0000000000000000
Internal error: Oops: 96000047 [#2] PREEMPT SMP
...
Call trace:
__memcpy+0x74/0x180
ufshcd_issue_devman_upiu_cmd+0x250/0x3c0
ufshcd_exec_raw_upiu_cmd+0xfc/0x1a8
ufs_bsg_request+0x178/0x3b0
bsg_queue_rq+0xc0/0x118
blk_mq_dispatch_rq_list+0xb0/0x538
blk_mq_sched_dispatch_requests+0x18c/0x1d8
__blk_mq_run_hw_queue+0xb4/0x118
blk_mq_run_work_fn+0x28/0x38
process_one_work+0x1ec/0x470
worker_thread+0x48/0x458
kthread+0x130/0x138
ret_from_fork+0x10/0x1c
Code: 540000aba8c12027a88120c7a8c12027 (a88120c7)
---[ end trace 793e1eb5dff69f2d ]---
note: kworker/0:2H[2054] exited with preempt_count 1
This patch is to move "descriptor = NULL" down to below the label
"out_unlock".
Fixes: d44a5f98bb49b2(ufs: query descriptor API) Link: https://lore.kernel.org/r/20191112223436.27449-3-huobean@gmail.com Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com> Reviewed-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Bean Huo <beanhuo@micron.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
*** CID 101747: Null pointer dereferences (FORWARD_NULL)
/drivers/scsi/lpfc/lpfc_els.c: 4439 in lpfc_cmpl_els_rsp()
4433 kfree(mp);
4434 }
4435 mempool_free(mbox, phba->mbox_mem_pool);
4436 }
4437 out:
4438 if (ndlp && NLP_CHK_NODE_ACT(ndlp)) {
vvv CID 101747: Null pointer dereferences (FORWARD_NULL)
vvv Dereferencing null pointer "shost".
4439 spin_lock_irq(shost->host_lock);
4440 ndlp->nlp_flag &= ~(NLP_ACC_REGLOGIN | NLP_RM_DFLT_RPI);
4441 spin_unlock_irq(shost->host_lock);
4442
4443 /* If the node is not being used by another discovery thread,
4444 * and we are sending a reject, we are done with it.
Fix by adding a check for non-null shost in line 4438.
The scenario when shost is set to null is when ndlp is null.
As such, the ndlp check present was sufficient. But better safe
than sorry so add the shost check.
Reported-by: coverity-bot <keescook+coverity-bot@chromium.org>
Addresses-Coverity-ID: 101747 ("Null pointer dereferences") Fixes: 2e0fef85e098 ("[SCSI] lpfc: NPIV: split ports") CC: James Bottomley <James.Bottomley@SteelEye.com> CC: "Gustavo A. R. Silva" <gustavo@embeddedor.com> CC: linux-next@vger.kernel.org Link: https://lore.kernel.org/r/20191111230401.12958-3-jsmart2021@gmail.com Reviewed-by: Ewan D. Milne <emilne@redhat.com> Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Quota statistics counted as 64-bit per-cpu counter. Reading sums per-cpu
fractions as signed 64-bit int, filters negative values and then reports
lower half as signed 32-bit int.
Some RCGs (the gfx_3d_src_clk in msm8998 for example) are basically just
some constant ratio from the input across the entire frequency range. It
would be great if we could specify the frequency table as a single entry
constant ratio instead of a long list, ie:
{ .src = P_GPUPLL0_OUT_EVEN, .pre_div = 3 },
{ }
So, lets support that.
We need to fix a corner case in qcom_find_freq() where if the freq table
is non-null, but has no frequencies, we end up returning an "entry" before
the table array, which is bad. Then, we need ignore the freq from the
table, and instead base everything on the requested freq.
Suggested-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com> Link: https://lkml.kernel.org/r/20191031185715.15504-1-jeffrey.l.hugo@gmail.com Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This is causing xfstest generic/579 to fail due to fsck.f2fs reporting errors.
I'm not sure what the problem is, but it still happens even with all the
fs-verity stuff in the test commented out, so that the test just runs fsstress.
generic/579 23s ... [10:02:25]
[ 7.745370] run fstests generic/579 at 2019-11-04 10:02:25
_check_generic_filesystem: filesystem on /dev/vdc is inconsistent
(see /results/f2fs/results-default/generic/579.full for details)
[10:02:47]
Ran: generic/579
Failures: generic/579
Failed 1 of 1 tests
Xunit report: /results/f2fs/results-default/result.xml
Here's the contents of 579.full:
_check_generic_filesystem: filesystem on /dev/vdc is inconsistent
*** fsck.f2fs output ***
[ASSERT] (__chk_dots_dentries:1378) --> Bad inode number[0x24] for '..', parent parent ino is [0xd10]
The root cause is that we forgot to update directory's i_pino during
cross_rename, fix it.
Fixes: 32f9bc25cbda0 ("f2fs: support ->rename2()") Signed-off-by: Chao Yu <yuchao0@huawei.com> Tested-by: Eric Biggers <ebiggers@kernel.org> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If the driver receives a login that is later then LOGO'd by the remote port
(aka ndlp), the driver, upon the completion of the LOGO ACC transmission,
will logout the node and unregister the rpi that is being used for the
node. As part of the unreg, the node's rpi value is replaced by the
LPFC_RPI_ALLOC_ERROR value. If the port is subsequently offlined, the
offline walks the nodes and ensures they are logged out, which possibly
entails unreg'ing their rpi values. This path does not validate the node's
rpi value, thus doesn't detect that it has been unreg'd already. The
replaced rpi value is then used when accessing the rpi bitmask array which
tracks active rpi values. As the LPFC_RPI_ALLOC_ERROR value is not a valid
index for the bitmask, it may fault the system.
Revise the rpi release code to detect when the rpi value is the replaced
RPI_ALLOC_ERROR value and ignore further release steps.
Link: https://lore.kernel.org/r/20191105005708.7399-2-jsmart2021@gmail.com Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
jbd2 statistics counting number of blocks logged in a transaction was
wrong. It didn't count the commit block and more importantly it didn't
count revoke descriptor blocks. Make sure these get properly counted.
Reviewed-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20191105164437.32602-13-jack@suse.cz Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This patch updates the lock pattern in ext4_direct_IO_read() to not
block on inode lock in cases of IOCB_NOWAIT direct I/O reads. The
locking condition implemented here is similar to that of 942491c9e6d6
("xfs: fix AIM7 regression").
Fixes: 16c54688592c ("ext4: Allow parallel DIO reads") Signed-off-by: Matthew Bobrowski <mbobrowski@mbobrowski.org> Reviewed-by: Jan Kara <jack@suse.cz> Reviewed-by: Ritesh Harjani <riteshh@linux.ibm.com> Link: https://lore.kernel.org/r/c5d5e759f91747359fbd2c6f9a36240cf75ad79f.1572949325.git.mbobrowski@mbobrowski.org Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
With large memory (8TB and more) hotplug, we can get soft lockup
warnings as below. These were caused by a long loop without any
explicit cond_resched which is a problem for !PREEMPT kernels.
Avoid this using cond_resched() while inserting hash page table
entries. We already do similar cond_resched() in __add_pages(), see
commit f64ac5e6e306 ("mm, memory_hotplug: add scheduling point to
__add_pages").
Some of our scripts are passed $objdump and then call it as
"$objdump". This doesn't work if it contains spaces because we're
using ccache, for example you get errors such as:
./arch/powerpc/tools/relocs_check.sh: line 48: ccache ppc64le-objdump: No such file or directory
./arch/powerpc/tools/unrel_branch_check.sh: line 26: ccache ppc64le-objdump: No such file or directory
Fix it by not quoting the string when we expand it, allowing the shell
to do the right thing for us.
Fixes: a71aa05e1416 ("powerpc: Convert relocs_check to a shell script using grep") Fixes: 4ea80652dc75 ("powerpc/64s: Tool to flag direct branches from unrelocated interrupt vectors") Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20191024004730.32135-1-mpe@ellerman.id.au Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If the hypervisor returned H_PTEG_FULL for H_ENTER hcall, retry a hash page table
insert by removing a random entry from the group.
After some runtime, it is very well possible to find all the 8 hash page table
entry slot in the hpte group used for mapping. Don't fail a bolted entry insert
in that case. With Storage class memory a user can find this error easily since
a namespace enable/disable is equivalent to memory add/remove.
This results in failures as reported below:
$ ndctl create-namespace -r region1 -t pmem -m devdax -a 65536 -s 100M
libndctl: ndctl_dax_enable: dax1.3: failed to enable
Error: namespace1.2: failed to enable
failed to create namespace: No such device or address
In kernel log we find the details as below:
Unable to create mapping for hot added memory 0xc000042006000000..0xc00004200d000000: -1
dax_pmem: probe of dax1.3 failed with error -14
This indicates that we failed to create a bolted hash table entry for direct-map
address backing the namespace.
We also observe failures such that not all namespaces will be enabled with
ndctl enable-namespace all command.
When operating in private loop mode, PLOGI exchanges are racing and the
driver tries to abort it's PLOGI. But the PLOGI abort ends up terminating
the login with the other end causing the other end to abort its PLOGI as
well. Discovery never fully completes.
Fix by disabling the PLOGI abort when private loop and letting the state
machine play out.
Link: https://lore.kernel.org/r/20191018211832.7917-5-jsmart2021@gmail.com Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
For CHAP [RFC1994], in the first step, the initiator MUST send:
CHAP_A=<A1,A2...>
Where A1,A2... are proposed algorithms, in order of preference.
...
For the Algorithm, as stated in [RFC1994], one value is required to
be implemented:
5 (CHAP with MD5)
LIO currently checks for this value by only comparing a single byte in
the tokenized Algorithm string, which means that any value starting with
a '5' (e.g. "55") is interpreted as "CHAP with MD5". Fix this by
comparing the entire tokenized string.
Reviewed-by: Lee Duncan <lduncan@suse.com> Reviewed-by: Mike Christie <mchristi@redhat.com> Signed-off-by: David Disseldorp <ddiss@suse.de> Link: https://lore.kernel.org/r/20190912095547.22427-2-ddiss@suse.de Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Page tables that reside in physical memory beyond the 4 GiB boundary are
currently not working properly. The reason is that when the physical
address for page directory entries is read, it gets truncated at 32 bits
and can cause crashes when passing that address to the DMA API.
Fix this by first casting the PDE value to a dma_addr_t and then using
the page frame number mask for the SMMU instance to mask out the invalid
bits, which are typically used for mapping attributes, etc.
Across suspend and resume, we are seeing error messages like the following:
atmel_mxt_ts i2c-PRP0001:00: __mxt_read_reg: i2c transfer failed (-121)
atmel_mxt_ts i2c-PRP0001:00: Failed to read T44 and T5 (-121)
This occurs because the driver leaves its IRQ enabled. Upon resume, there
is an IRQ pending, but the interrupt is serviced before both the driver and
the underlying I2C bus have been resumed. This causes EREMOTEIO errors.
Disable the IRQ in suspend, and re-enable it on resume. If there are cases
where the driver enters suspend with interrupts disabled, that's a bug we
should fix separately.
Signed-off-by: Evan Green <evgreen@chromium.org> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Symptoms were seen of the driver not having valid data for mailbox
commands. After debugging, the following sequence was found:
The driver maintains a port-wide pointer of the mailbox command that is
currently in execution. Once finished, the port-wide pointer is cleared
(done in lpfc_sli4_mq_release()). The next mailbox command issued will set
the next pointer and so on.
The mailbox response data is only copied if there is a valid port-wide
pointer.
In the failing case, it was seen that a new mailbox command was being
attempted in parallel with the completion. The parallel path was seeing
the mailbox no long in use (flag check under lock) and thus set the port
pointer. The completion path had cleared the active flag under lock, but
had not touched the port pointer. The port pointer is cleared after the
lock is released. In this case, the completion path cleared the just-set
value by the parallel path.
Fix by making the calls that clear mbox state/port pointer while under
lock. Also slightly cleaned up the error path.
Link: https://lore.kernel.org/r/20190922035906.10977-8-jsmart2021@gmail.com Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When user issues diag register command from application with required size,
and if driver unable to allocate the memory, then it will fail the register
command. While failing the register command, driver is not currently
clearing MPT3_CMD_PENDING bit in ctl_cmds.status variable which was set
before trying to allocate the memory. As this bit is set, subsequent
register command will be failed with BUSY status even when user wants to
register the trace buffer will less memory.
Clear MPT3_CMD_PENDING bit in ctl_cmds.status before returning the diag
register command with no memory status.
Link: https://lore.kernel.org/r/1568379890-18347-4-git-send-email-sreekanth.reddy@broadcom.com Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
An issue was seen discovering all SCSI Luns when a target device undergoes
link bounce.
The driver currently does not qualify the FC4 support on the target.
Therefore it will send a SCSI PRLI and an NVMe PRLI. The expectation is
that the target will reject the PRLI if it is not supported. If a PRLI
times out, the driver will retry. The driver will not proceed with the
device until both SCSI and NVMe PRLIs are resolved. In the failure case,
the device is FCP only and does not respond to the NVMe PRLI, thus
initiating the wait/retry loop in the driver. During that time, a RSCN is
received (device bounced) causing the driver to issue a GID_FT. The GID_FT
response comes back before the PRLI mess is resolved and it prematurely
cancels the PRLI retry logic and leaves the device in a STE_PRLI_ISSUE
state. Discovery with the target never completes or resets.
Fix by resetting the node state back to STE_NPR_NODE when GID_FT completes,
thereby restarting the discovery process for the node.
Link: https://lore.kernel.org/r/20190922035906.10977-10-jsmart2021@gmail.com Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Command queuing has been reported broken on some systems based on Intel
GLK. A separate patch disables command queuing in some cases.
This patch adds a quirk for broken command queuing, which enables users
with problems to disable command queuing using sdhci module parameters for
quirks.
Fixes: 8ee82bda230f ("mmc: sdhci-pci: Add CQHCI support for Intel GLK") Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20191217095349.14592-2-adrian.hunter@intel.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The scheduler code calling cpufreq_update_util() may run during CPU
offline on the target CPU after the IRQ work lists have been flushed
for it, so the target CPU should be prevented from running code that
may queue up an IRQ work item on it at that point.
Unfortunately, that may not be the case if dvfs_possible_from_any_cpu
is set for at least one cpufreq policy in the system, because that
allows the CPU going offline to run the utilization update callback
of the cpufreq governor on behalf of another (online) CPU in some
cases.
If that happens, the cpufreq governor callback may queue up an IRQ
work on the CPU running it, which is going offline, and the IRQ work
may not be flushed after that point. Moreover, that IRQ work cannot
be flushed until the "offlining" CPU goes back online, so if any
other CPU calls irq_work_sync() to wait for the completion of that
IRQ work, it will have to wait until the "offlining" CPU is back
online and that may not happen forever. In particular, a system-wide
deadlock may occur during CPU online as a result of that.
The failing scenario is as follows. CPU0 is the boot CPU, so it
creates a cpufreq policy and becomes the "leader" of it
(policy->cpu). It cannot go offline, because it is the boot CPU.
Next, other CPUs join the cpufreq policy as they go online and they
leave it when they go offline. The last CPU to go offline, say CPU3,
may queue up an IRQ work while running the governor callback on
behalf of CPU0 after leaving the cpufreq policy because of the
dvfs_possible_from_any_cpu effect described above. Then, CPU0 is
the only online CPU in the system and the stale IRQ work is still
queued on CPU3. When, say, CPU1 goes back online, it will run
irq_work_sync() to wait for that IRQ work to complete and so it
will wait for CPU3 to go back online (which may never happen even
in principle), but (worse yet) CPU0 is waiting for CPU1 at that
point too and a system-wide deadlock occurs.
To address this problem notice that CPUs which cannot run cpufreq
utilization update code for themselves (for example, because they
have left the cpufreq policies that they belonged to), should also
be prevented from running that code on behalf of the other CPUs that
belong to a cpufreq policy with dvfs_possible_from_any_cpu set and so
in that case the cpufreq_update_util_data pointer of the CPU running
the code must not be NULL as well as for the CPU which is the target
of the cpufreq utilization update in progress.
Accordingly, change cpufreq_this_cpu_can_update() into a regular
function in kernel/sched/cpufreq.c (instead of a static inline in a
header file) and make it check the cpufreq_update_util_data pointer
of the local CPU if dvfs_possible_from_any_cpu is set for the target
cpufreq policy.
Also update the schedutil governor to do the
cpufreq_this_cpu_can_update() check in the non-fast-switch
case too to avoid the stale IRQ work issues.
Fixes: 99d14d0e16fa ("cpufreq: Process remote callbacks from any CPU if the platform permits") Link: https://lore.kernel.org/linux-pm/20191121093557.bycvdo4xyinbc5cb@vireshk-i7/ Reported-by: Anson Huang <anson.huang@nxp.com> Tested-by: Anson Huang <anson.huang@nxp.com> Cc: 4.14+ <stable@vger.kernel.org> # 4.14+ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Tested-by: Peng Fan <peng.fan@nxp.com> (i.MX8QXP-MEK) Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Viresh Kumar [Tue, 22 May 2018 10:01:30 +0000 (15:31 +0530)]
cpufreq: Rename cpufreq_can_do_remote_dvfs()
BugLink: https://bugs.launchpad.net/bugs/1859712
This routine checks if the CPU running this code belongs to the policy
of the target CPU or if not, can it do remote DVFS for it remotely. But
the current name of it implies as if it is only about doing remote
updates.
Rename it to make it more relevant.
Suggested-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
(cherry picked from commit 036399782bf51dafb932b680b260936b2b5f8dd6) Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
BugLink: https://bugs.launchpad.net/bugs/1859712
ALE is enabled from cpsw_ale_start() now, but disabled only from
cpsw_ale_destroy() which introduces inconsitance as cpsw_ale_start() is
called when netif[s] is opened, but cpsw_ale_destroy() is called when
driver is removed. Hence, move ALE disabling in cpsw_ale_stop().
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
(cherry picked from commit d0aef029b53c70d6261ef9d4bd827c861d51a8ef) Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
There is a race in the TUN driver between napi_busy_loop and
napi_gro_frags. This commit resolves the race by adding the NAPI struct
via netif_tx_napi_add, instead of netif_napi_add, which disables polling
for the NAPI struct.
KCSAN reported:
BUG: KCSAN: data-race in gro_normal_list.part.0 / napi_busy_loop
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 11168 Comm: syz-executor.0 Not tainted 5.4.0-rc6+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Fixes: 943170998b20 ("tun: enable NAPI for TUN/TAP driver") Signed-off-by: Petar Penkov <ppenkov@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The AD5600 is a single channel, 16-bit resolution, voltage output digital
to analog converter (DAC). The AD5600 uses a 3-wire SPI interface. It is
part of the AD5541 family of DACs.
The ad5446 IIO driver implements support for some of these DACs (in the
AD5441 family), so the change is a simple entry in this driver.
Link: https://www.analog.com/media/en/technical-documentation/data-sheets/AD5600.pdf Signed-off-by: Stefan Popa <stefan.popa@analog.com> Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If event parsing fails the event list is leaked, instead splice the list
onto the out result and let the caller cleanup.
An example input for parse_events found by libFuzzer that reproduces
this memory leak is 'm{'.
Signed-off-by: Ian Rogers <irogers@google.com> Acked-by: Jiri Olsa <jolsa@kernel.org> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Alexei Starovoitov <ast@kernel.org> Cc: Andi Kleen <ak@linux.intel.com> Cc: Daniel Borkmann <daniel@iogearbox.net> Cc: Jin Yao <yao.jin@linux.intel.com> Cc: John Garry <john.garry@huawei.com> Cc: Kan Liang <kan.liang@linux.intel.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Martin KaFai Lau <kafai@fb.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Song Liu <songliubraving@fb.com> Cc: Stephane Eranian <eranian@google.com> Cc: Yonghong Song <yhs@fb.com> Cc: bpf@vger.kernel.org Cc: clang-built-linux@googlegroups.com Cc: netdev@vger.kernel.org Link: http://lore.kernel.org/lkml/20191025180827.191916-5-irogers@google.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If software running before the OCOTP driver is loaded left the
controller with the error status pending, the driver will never
be able to complete the read timing setup. Reset the error status
on probe to make sure the controller is in usable state.
When there is a TX timeout, we can tell if the driver or stack
has stopped the queue by looking at state field, and when has
the last packet transmited by looking at trans_start field.
So this patch prints these two field in the
hns3_get_tx_timeo_queue_info().
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
And the procedure to keep resize bitmap safe is allocate new storage
space, then quiesce, copy bits, replace bitmap, and re-start.
However the daemon (bitmap_daemon_work) could happen even the array is
quiesced, which means when bitmap_file_clear_bit is triggered by raid1d,
then it thinks it should be fine to access store->filemap since
counts->lock is held, but resize could change the storage without the
protection of the lock.
Cc: Jack Wang <jinpu.wang@cloud.ionos.com> Cc: NeilBrown <neilb@suse.com> Signed-off-by: Guoqing Jiang <guoqing.jiang@cloud.ionos.com> Signed-off-by: Song Liu <songliubraving@fb.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Earlier it was possible that the parts of the driver that assumed runtime
PM was enabled were being called before runtime PM was enabled in the
driver's probe function. So enable runtime PM before registering the
sub-device.
It appears that some Broadcom controllers (eg BCM20702A0) reject LE Set
Advertising Parameters command if advertising intervals provided are not
within range for undirected and low duty directed advertising.
Workaround this bug by populating min and max intervals with 'valid'
values.
< HCI Command: LE Set Advertising Parameters (0x08|0x0006) plen 15
Min advertising interval: 0.000 msec (0x0000)
Max advertising interval: 0.000 msec (0x0000)
Type: Connectable directed - ADV_DIRECT_IND (high duty cycle) (0x01)
Own address type: Public (0x00)
Direct address type: Random (0x01)
Direct address: E2:F0:7B:9F:DC:F4 (Static)
Channel map: 37, 38, 39 (0x07)
Filter policy: Allow Scan Request from Any, Allow Connect Request from Any (0x00)
> HCI Event: Command Complete (0x0e) plen 4
LE Set Advertising Parameters (0x08|0x0006) ncmd 1
Status: Invalid HCI Command Parameters (0x12)
For historical reasons, the function drm_wait_vblank_ioctl always return
-EINVAL if something gets wrong. This scenario limits the flexibility
for the userspace to make detailed verification of any problem and take
some action. In particular, the validation of “if (!dev->irq_enabled)”
in the drm_wait_vblank_ioctl is responsible for checking if the driver
support vblank or not. If the driver does not support VBlank, the
function drm_wait_vblank_ioctl returns EINVAL, which does not represent
the real issue; this patch changes this behavior by return EOPNOTSUPP.
Additionally, drm_crtc_get_sequence_ioctl and
drm_crtc_queue_sequence_ioctl, also returns EINVAL if vblank is not
supported; this patch also changes the return value to EOPNOTSUPP in
these functions. Lastly, these functions are invoked by libdrm, which is
used by many compositors; because of this, it is important to check if
this change breaks any compositor. In this sense, the following projects
were examined:
* Drm-hwcomposer
* Kwin
* Sway
* Wlroots
* Wayland
* Weston
* Mutter
* Xorg (67 different drivers)
For each repository the verification happened in three steps:
* Update the main branch
* Look for any occurrence of "drmCrtcQueueSequence",
"drmCrtcGetSequence", and "drmWaitVBlank" with the command git grep -n
"STRING".
* Look in the git history of the project with the command
git log -S<STRING>
None of the above projects validate the use of EINVAL when using
drmWaitVBlank(), which make safe, at least for these projects, to change
the return values. On the other hand, mesa and xserver project uses
drmCrtcQueueSequence() and drmCrtcGetSequence(); this change is harmless
for both projects.
Change since V5 (Pekka Paalanen):
- Check if the change also affects Mutter
Change since V4 (Daniel):
- Also return EOPNOTSUPP in drm_crtc_[get|queue]_sequence_ioctl
Change since V3:
- Return EINVAL for _DRM_VBLANK_SIGNAL (Daniel)
Change since V2:
Daniel Vetter and Chris Wilson
- Replace ENOTTY by EOPNOTSUPP
- Return EINVAL if the parameters are wrong
Cc: Keith Packard <keithp@keithp.com> Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Daniel Vetter <daniel@ffwll.ch> Cc: Pekka Paalanen <pekka.paalanen@collabora.com> Signed-off-by: Rodrigo Siqueira <rodrigosiqueiramelo@gmail.com> Reviewed-by: Daniel Vetter <daniel@ffwll.ch> Acked-by: Pekka Paalanen <pekka.paalanen@collabora.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191002140516.adeyj3htylimmlmg@smtp.gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Signed-off-by: Allen Pais <allen.pais@oracle.com> Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com> Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Panels must be initialised with drm_panel_init(). Add the missing
function call in the panel-raspberrypi-touchscreen.c and
panel-sitronix-st7789v.c drivers.
CA0132 has the delayed HP jack detection code that is invoked from the
unsol handler, but it does a few weird things: it contains the cancel
of a work inside the work handler, and yet it misses the cancel-sync
call at (runtime-)suspend. This patch addresses those issues.