Jarkko Nikula [Thu, 30 Aug 2018 03:54:00 +0000 (05:54 +0200)]
mfd: intel-lpss: Fix Intel Cannon Lake LPSS I2C input clock
BugLink: https://bugs.launchpad.net/bugs/1789790
Intel Cannon Lake PCH has much higher 216 MHz input clock to LPSS I2C
than Sunrisepoint which uses 120 MHz. Preliminary information was that
both share the same clock rate but actual silicon implements elevated
rate for better support for 3.4 MHz high-speed I2C.
This incorrect input clock rate results too high I2C bus clock in case
ACPI doesn't provide tuned I2C timing parameters since I2C host
controller driver calculates them from input clock rate.
Fix this by using the correct rate. We still share the same 230 ns SDA
hold time value than Sunrisepoint.
Cc: stable@vger.kernel.org Fixes: b418bbff36dd ("mfd: intel-lpss: Add Intel Cannonlake PCI IDs") Reported-by: Jian-Hong Pan <jian-hong@endlessm.com> Reported-by: Chris Chiu <chiu@endlessm.com> Reported-by: Daniel Drake <drake@endlessm.com> Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Tested-by: Jian-Hong Pan <jian-hong@endlessm.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
(cherry picked from commit 4e93a658576ab115977225c9d0992b97ff19ba8c) Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Acked-by: Colin Ian King <colin.king@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Paolo Pisati [Mon, 27 Aug 2018 09:18:00 +0000 (11:18 +0200)]
UBUNTU: [Config] disable ARCH_TANGO
BugLink: https://bugs.launchpad.net/bugs/1787945
The TANGO platform is enabled by default in the multiplatform ARM kernel.
However, it calls __initcall in arch/arm/mach-tango/pm.c without a check whether
it actually runs on this hw. This causes an OOPS during suspend on my Tegra
platform. Please disable this (multiplatform incompatible) arch.
Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Seth Forshee <seth.forshee@canonical.com>
[ kleber: remove tango-ir and tango_nand modules from prebious ABI's
modules list for armhf. ] Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
When operating the system headless headless, the domain is never
powered on, leaving the clocks disabled. The shutdown function then
tries to disable the already disabled clocks, resulting in errors.
Therefore call meson_gx_pwrc_vpu_power_off() only if domain is
powered on.
This patch fixes the described issue on my system (Odorid-C2).
Fixes: 339cd0ea0822 "soc: amlogic: meson-gx-pwrc-vpu: fix power-off when powered by bootloader" Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Add test cases verifying FIB onlink commands work as expected in
various conditions - IPv4, IPv6, main table, and VRF.
Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
drm_vblank_count() has an u32 type returning what is a 64-bit vblank count.
The effect of this is when drm_wait_vblank_ioctl() tries to widen the user
space requested vblank sequence using this clipped 32-bit count(when the
value is >= 2^32) as reference, the requested sequence remains a 32-bit
value and gets queued like that. However, the code that checks if the
requested sequence has passed compares this against the 64-bit vblank
count.
With drm_vblank_count() returning all bits of the vblank count, update
drm_crtc_accurate_vblank_count() so that drm_crtc_arm_vblank_event() queues
the correct sequence. Otherwise, this leads to prolonged waits for a vblank
sequence when the current count is >=2^32.
According to the figure 9.2(b) of the R-Car Series, 3rd Generation User’s
Manual: Hardware Rev. 0.80 the A2IRn and A2SCn power areas in R8A77970 have
the A3IR area as a parent, thus the SYSC driver has those parents wrong...
Brightness couldn't change when booting up in DC mode.
It was because "psr_enabled" flag was not set to true before
setting vsc packet revision, causing packet rev setup was skipped.
Now instead of checking the psr flag, it checks if the DPCD_REV >= 1.2
and set the vsc packet revision.
Signed-off-by: Tao <xtao@amd.com> Reviewed-by: Tony Cheng <Tony.Cheng@amd.com> Acked-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Currently, buffers holding individual queue statistics are allocated
when the device is opened. If an ibmvnic interface is hotplugged or
initialized but never opened, an attempt to get statistics with
ethtool will result in a kernel panic.
Since the driver allocates a constant number, the maximum supported
queues, of buffers, these can be allocated during device probe and
freed when the device is hot-unplugged or the module is removed.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
On the 8xx, the page size is set in the PMD entry and applies to
all pages of the page table pointed by the said PMD entry.
When an app has some regular pages allocated (e.g. see below) and tries
to mmap() a huge page at a hint address covered by the same PMD entry,
the kernel accepts the hint allthough the 8xx cannot handle different
page sizes in the same PMD entry.
In order to fix this, this patch uses the address space "slices"
implemented for BOOK3S/64 and enhanced to support PPC32 by the
preceding patch.
This patch modifies the context.id on the 8xx to be in the range
[1:16] instead of [0:15] in order to identify context.id == 0 as
not initialised contexts as done on BOOK3S
This patch activates CONFIG_PPC_MM_SLICES when CONFIG_HUGETLB_PAGE is
selected for the 8xx
Alltough we could in theory have as many slices as PMD entries, the
current slices implementation limits the number of low slices to 16.
This limitation is not preventing us to fix the initial issue allthough
it is suboptimal. It will be cured in a subsequent patch.
Fixes: 4b91428699477 ("powerpc/8xx: Implement support of hugepages") Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr> Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In preparation for the following patch which will fix an issue on
the 8xx by re-using the 'slices', this patch enhances the
'slices' implementation to support 32 bits CPUs.
On PPC32, the address space is limited to 4Gbytes, hence only the low
slices will be used.
The high slices use bitmaps. As bitmap functions are not prepared to
handle bitmaps of size 0, this patch ensures that bitmap functions
are called only when SLICE_NUM_HIGH is not nul.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr> Reviewed-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In preparation for the following patch which will enhance 'slices'
for supporting PPC32 in order to fix an issue on hugepages on 8xx,
this patch takes out of page*.h all bits related to 'slices' and put
them into newly created slice.h header files.
While common parts go into asm/slice.h, subarch specific
parts go into respective books3s/64/slice.c and nohash/64/slice.c
'slices'
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr> Reviewed-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
bitmap_or() and bitmap_andnot() can work properly with dst identical
to src1 or src2. There is no need of an intermediate result bitmap
that is copied back to dst in a second step.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr> Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Reviewed-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The sdma wptr polling memory is not fast enough, then the sdma
wptr register will be random, and not equal to sdma rptr, which
will cause sdma engine hang when load driver, so clean up the sdma
wptr directly to fix this issue.
v2:add comment above the code and correct coding style
Reviewed-by: Xiangliang Yu <Xiangliang.Yu@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Emily Deng <Emily.Deng@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Previously, we attempt to flush the whole cp pack in a single bio,
however, when suddenly powering off at this time, we could get into
an extreme scenario that cp pack 1 page and cp pack 2 page are updated
and latest, but payload or current summaries are still partially
outdated. (see reliable write in the UFS specification)
This patch submits the whole cp pack except cp pack 2 page at first,
and then writes the cp pack 2 page with an extra independent
bio with pre-io barrier.
The case in which we handle a reset from the state where the device is
closed seems to be bugged for all types of reset. For most types of reset
we currently exit the reset routine correctly, but don't set the state to
indicate that we are back in the "closed" state. For some specific cases,
we don't exit the reset routine at all and resetting will cause a closed
device to be opened.
This patch fixes the problem by unconditionally checking the reset_state
and correctly setting the adapter state before returning.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
struct delayed_work writeback_rate_update in struct cache_dev is a delayed
worker to call function update_writeback_rate() in period (the interval is
defined by dc->writeback_rate_update_seconds).
When a metadate I/O error happens on cache device, bcache error handling
routine bch_cache_set_error() will call bch_cache_set_unregister() to
retire whole cache set. On the unregister code path, this delayed work is
stopped by calling cancel_delayed_work_sync(&dc->writeback_rate_update).
dc->writeback_rate_update is a special delayed work from others in bcache.
In its routine update_writeback_rate(), this delayed work is re-armed
itself. That means when cancel_delayed_work_sync() returns, this delayed
work can still be executed after several seconds defined by
dc->writeback_rate_update_seconds.
The problem is, after cancel_delayed_work_sync() returns, the cache set
unregister code path will continue and release memory of struct cache set.
Then the delayed work is scheduled to run, __update_writeback_rate()
will reference the already released cache_set memory, and trigger a NULL
pointer deference fault.
This patch introduces two more bcache device flags,
- BCACHE_DEV_WB_RUNNING
bit set: bcache device is in writeback mode and running, it is OK for
dc->writeback_rate_update to re-arm itself.
bit clear:bcache device is trying to stop dc->writeback_rate_update,
this delayed work should not re-arm itself and quit.
- BCACHE_DEV_RATE_DW_RUNNING
bit set: routine update_writeback_rate() is executing.
bit clear: routine update_writeback_rate() quits.
This patch also adds a function cancel_writeback_rate_update_dwork() to
wait for dc->writeback_rate_update quits before cancel it by calling
cancel_delayed_work_sync(). In order to avoid a deadlock by unexpected
quit dc->writeback_rate_update, after time_out seconds this function will
give up and continue to call cancel_delayed_work_sync().
And here I explain how this patch stops self re-armed delayed work properly
with the above stuffs.
update_writeback_rate() sets BCACHE_DEV_RATE_DW_RUNNING at its beginning
and clears BCACHE_DEV_RATE_DW_RUNNING at its end. Before calling
cancel_writeback_rate_update_dwork() clear flag BCACHE_DEV_WB_RUNNING.
Before calling cancel_delayed_work_sync() wait utill flag
BCACHE_DEV_RATE_DW_RUNNING is clear. So when calling
cancel_delayed_work_sync(), dc->writeback_rate_update must be already re-
armed, or quite by seeing BCACHE_DEV_WB_RUNNING cleared. In both cases
delayed work routine update_writeback_rate() won't be executed after
cancel_delayed_work_sync() returns.
Inside update_writeback_rate() before calling schedule_delayed_work(), flag
BCACHE_DEV_WB_RUNNING is checked before. If this flag is cleared, it means
someone is about to stop the delayed work. Because flag
BCACHE_DEV_RATE_DW_RUNNING is set already and cancel_delayed_work_sync()
has to wait for this flag to be cleared, we don't need to worry about race
condition here.
If update_writeback_rate() is scheduled to run after checking
BCACHE_DEV_RATE_DW_RUNNING and before calling cancel_delayed_work_sync()
in cancel_writeback_rate_update_dwork(), it is also safe. Because at this
moment BCACHE_DEV_WB_RUNNING is cleared with memory barrier. As I mentioned
previously, update_writeback_rate() will see BCACHE_DEV_WB_RUNNING is clear
and quit immediately.
Because there are more dependences inside update_writeback_rate() to struct
cache_set memory, dc->writeback_rate_update is not a simple self re-arm
delayed work. After trying many different methods (e.g. hold dc->count, or
use locks), this is the only way I can find which works to properly stop
dc->writeback_rate_update delayed work.
Changelog:
v3: change values of BCACHE_DEV_WB_RUNNING and BCACHE_DEV_RATE_DW_RUNNING
to bit index, for test_bit().
v2: Try to fix the race issue which is pointed out by Junhui.
v1: The initial version for review
Signed-off-by: Coly Li <colyli@suse.de> Reviewed-by: Junhui Tang <tang.junhui@zte.com.cn> Reviewed-by: Michael Lyle <mlyle@lyle.org> Cc: Michael Lyle <mlyle@lyle.org> Cc: Hannes Reinecke <hare@suse.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When bcache metadata I/O fails, bcache will call bch_cache_set_error()
to retire the whole cache set. The expected behavior to retire a cache
set is to unregister the cache set, and unregister all backing device
attached to this cache set, then remove sysfs entries of the cache set
and all attached backing devices, finally release memory of structs
cache_set, cache, cached_dev and bcache_device.
In my testing when journal I/O failure triggered by disconnected cache
device, sometimes the cache set cannot be retired, and its sysfs
entry /sys/fs/bcache/<uuid> still exits and the backing device also
references it. This is not expected behavior.
When metadata I/O failes, the call senquence to retire whole cache set is,
bch_cache_set_error()
bch_cache_set_unregister()
bch_cache_set_stop()
__cache_set_unregister() <- called as callback by calling
clousre_queue(&c->caching)
cache_set_flush() <- called as a callback when refcount
of cache_set->caching is 0
cache_set_free() <- called as a callback when refcount
of catch_set->cl is 0
bch_cache_set_release() <- called as a callback when refcount
of catch_set->kobj is 0
I find if kernel thread bch_writeback_thread() quits while-loop when
kthread_should_stop() is true and searched_full_index is false, clousre
callback cache_set_flush() set by continue_at() will never be called. The
result is, bcache fails to retire whole cache set.
cache_set_flush() will be called when refcount of closure c->caching is 0,
and in function bcache_device_detach() refcount of closure c->caching is
released to 0 by clousre_put(). In metadata error code path, function
bcache_device_detach() is called by cached_dev_detach_finish(). This is a
callback routine being called when cached_dev->count is 0. This refcount
is decreased by cached_dev_put().
The above dependence indicates, cache_set_flush() will be called when
refcount of cache_set->cl is 0, and refcount of cache_set->cl to be 0
when refcount of cache_dev->count is 0.
The reason why sometimes cache_dev->count is not 0 (when metadata I/O fails
and bch_cache_set_error() called) is, in bch_writeback_thread(), refcount
of cache_dev is not decreased properly.
In bch_writeback_thread(), cached_dev_put() is called only when
searched_full_index is true and cached_dev->writeback_keys is empty, a.k.a
there is no dirty data on cache. In most of run time it is correct, but
when bch_writeback_thread() quits the while-loop while cache is still
dirty, current code forget to call cached_dev_put() before this kernel
thread exits. This is why sometimes cache_set_flush() is not executed and
cache set fails to be retired.
The reason to call cached_dev_put() in bch_writeback_rate() is, when the
cache device changes from clean to dirty, cached_dev_get() is called, to
make sure during writeback operatiions both backing and cache devices
won't be released.
Adding following code in bch_writeback_thread() does not work,
static int bch_writeback_thread(void *arg)
}
+ if (atomic_read(&dc->has_dirty))
+ cached_dev_put()
+
return 0;
}
because writeback kernel thread can be waken up and start via sysfs entry:
echo 1 > /sys/block/bcache<N>/bcache/writeback_running
It is difficult to check whether backing device is dirty without race and
extra lock. So the above modification will introduce potential refcount
underflow in some conditions.
The correct fix is, to take cached dev refcount when creating the kernel
thread, and put it before the kernel thread exits. Then bcache does not
need to take a cached dev refcount when cache turns from clean to dirty,
or to put a cached dev refcount when cache turns from ditry to clean. The
writeback kernel thread is alwasy safe to reference data structure from
cache set, cache and cached device (because a refcount of cache device is
taken for it already), and no matter the kernel thread is stopped by I/O
errors or system reboot, cached_dev->count can always be used correctly.
The patch is simple, but understanding how it works is quite complicated.
Changelog:
v2: set dc->writeback_thread to NULL in this patch, as suggested by Hannes.
v1: initial version for review.
Signed-off-by: Coly Li <colyli@suse.de> Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Michael Lyle <mlyle@lyle.org> Cc: Michael Lyle <mlyle@lyle.org> Cc: Junhui Tang <tang.junhui@zte.com.cn> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Coly Li [Wed, 7 Feb 2018 19:41:44 +0000 (11:41 -0800)]
bcache: set writeback_rate_update_seconds in range [1, 60] seconds
BugLink: http://bugs.launchpad.net/bugs/1786352
dc->writeback_rate_update_seconds can be set via sysfs and its value can
be set to [1, ULONG_MAX]. It does not make sense to set such a large
value, 60 seconds is long enough value considering the default 5 seconds
works well for long time.
Because dc->writeback_rate_update is a special delayed work, it re-arms
itself inside the delayed work routine update_writeback_rate(). When
stopping it by cancel_delayed_work_sync(), there should be a timeout to
wait and make sure the re-armed delayed work is stopped too. A small max
value of dc->writeback_rate_update_seconds is also helpful to decide a
reasonable small timeout.
This patch limits sysfs interface to set dc->writeback_rate_update_seconds
in range of [1, 60] seconds, and replaces the hand-coded number by macros.
Changelog:
v2: fix a rebase typo in v4, which is pointed out by Michael Lyle.
v1: initial version.
Signed-off-by: Coly Li <colyli@suse.de> Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Michael Lyle <mlyle@lyle.org> Signed-off-by: Jens Axboe <axboe@kernel.dk>
(cherry picked from commit 7a5e3ecbe5b7b58e9a78a3738b28244982822e1c) Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Currently fw_add_devm_name() returns 1 if the firmware cache
was already set. This makes it complicated for us to check for
correctness. It is actually non-fatal if the firmware cache
is already setup, so just return 0, and simplify the checkers.
fw_add_devm_name() adds device's name onto the devres for the
device so that prior to suspend we cache the firmware onto memory,
so that on resume the firmware is reliably available. We never
were checking for success for this call though, meaning in some
really rare cases we my have never setup the firmware cache for
a device, which could in turn make resume fail.
This is all theoretical, no known issues have been reported.
This small issue has been present way since the addition of the
devres firmware cache names on v3.7.
Fixes: f531f05ae9437 ("firmware loader: store firmware name into devres list") Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
As defined in hyperv_net.h, the NVSP_STAT_SUCCESS is one not zero.
Some functions returns 0 when it actually means NVSP_STAT_SUCCESS.
This patch fixes them.
In netvsc_receive(), it puts the last RNDIS packet's receive status
for all packets in a vmxferpage which may contain multiple RNDIS
packets.
This patch puts NVSP_STAT_FAIL in the receive completion if one of
the packets in a vmxferpage fails.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When we suspend and resume, we need to clear and re-enable the interrupt
scheme. This was previously not done while holding the RTNL lock, which
could be problematic, because we are actually destroying and re-creating
queues.
Hold the RTNL lock for the entire sequence of preparing for reset, and
when resuming. This additionally protects the flags related to interrupt
scheme under RTNL lock so that their modification is properly threaded.
This is part of a larger effort to remove the need for cmpxchg64 in
i40e_set_priv_flags().
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Commit a158bdd3 ("rxrpc: Fix call timeouts") reworked the time calculation
for the next resend event. For this calculation, "oldest" will be before
"now", so ktime_sub(oldest, now) will yield a negative value. When passed
to nsecs_to_jiffies which expects an unsigned value, the end result will be
a very large value, and a resend event scheduled far into the future. This
could cause calls to stall if some packets were lost.
Fix by ordering the arguments to ktime_sub correctly.
Fixes: a158bdd3247b ("rxrpc: Fix call timeouts") Signed-off-by: Marc Dionne <marc.dionne@auristor.com> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
We're freeing "value_name" which is NULL, so that's a no-op, but we
intended to free "location_name" instead. And then we don't free the
names in token_location_attrs[0] and token_value_attrs[0].
Fixes: 33b9ca1e53b4 ("platform/x86: dell-smbios: Add a sysfs interface for SMBIOS tokens") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Current implementations map locking operations using .rl and .aq
annotations. However, this mapping is unsound w.r.t. the kernel
memory consistency model (LKMM) [1]:
Referring to the "unlock-lock-read-ordering" test reported below,
Daniel wrote:
"I think an RCpc interpretation of .aq and .rl would in fact
allow the two normal loads in P1 to be reordered [...]
The intuition would be that the amoswap.w.aq can forward from
the amoswap.w.rl while that's still in the store buffer, and
then the lw x3,0(x4) can also perform while the amoswap.w.rl
is still in the store buffer, all before the l1 x1,0(x2)
executes. That's not forbidden unless the amoswaps are RCsc,
unless I'm missing something.
Likewise even if the unlock()/lock() is between two stores.
A control dependency might originate from the load part of
the amoswap.w.aq, but there still would have to be something
to ensure that this load part in fact performs after the store
part of the amoswap.w.rl performs globally, and that's not
automatic under RCpc."
Simulation of the RISC-V memory consistency model confirmed this
expectation.
In order to "synchronize" LKMM and RISC-V's implementation, this
commit strengthens the implementations of the locking operations
by replacing .rl and .aq with the use of ("lightweigth") fences,
resp., "fence rw, w" and "fence r , rw".
The kasan_slab_free hook's return value denotes whether the reuse of a
slab object must be delayed (e.g. when the object is put into memory
qurantine).
The current way SLUB handles this hook is by ignoring its return value
and hardcoding checks similar (but not exactly the same) to the ones
performed in kasan_slab_free, which is prone to making mistakes.
The main difference between the hardcoded checks and the ones in
kasan_slab_free is whether we want to perform a free in case when an
invalid-free or a double-free was detected (we don't).
This patch changes the way SLUB handles this by:
1. taking into account the return value of kasan_slab_free for each of
the objects, that are being freed;
2. reconstructing the freelist of objects to exclude the ones, whose
reuse must be delayed.
[andreyknvl@google.com: eliminate unnecessary branch in slab_free] Link: http://lkml.kernel.org/r/a62759a2545fddf69b0c034547212ca1eb1b3ce2.1520359686.git.andreyknvl@google.com Link: http://lkml.kernel.org/r/083f58501e54731203801d899632d76175868e97.1519400992.git.andreyknvl@google.com Signed-off-by: Andrey Konovalov <andreyknvl@google.com> Acked-by: Andrey Ryabinin <aryabinin@virtuozzo.com> Cc: Christoph Lameter <cl@linux.com> Cc: Pekka Enberg <penberg@kernel.org> Cc: David Rientjes <rientjes@google.com> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Alexander Potapenko <glider@google.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Kostya Serebryany <kcc@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The driver currently uses src port field (along with other fields) in the
decap tunnel key, while looking up and adding tunnel nodes. This leads to
redundant cfa_decap_filter_alloc() requests to the FW and flow-miss in the
flow engine. Fix this by ignoring the src port field in decap tunnel nodes.
Fixes: f484f6782e01 ("bnxt_en: add hwrm FW cmds for cfa_encap_record and decap_filter") Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Commit 08810a4119aa (PM / core: Add NEVER_SKIP and SMART_PREPARE
driver flags) inadvertently prevented the power.direct_complete flag
from being set for devices without PM callbacks and with disabled
runtime PM which also prevents power.direct_complete from being set
for their parents. That led to problems including a resume crash on
HP ZBook 14u.
Restore the previous behavior by causing power.direct_complete to be
set for those devices again, but do that in a more direct way to
avoid overlooking that case in the future.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=199693 Fixes: 08810a4119aa (PM / core: Add NEVER_SKIP and SMART_PREPARE driver flags) Reported-by: Thomas Martitz <kugel@rockbox.org> Tested-by: Thomas Martitz <kugel@rockbox.org> Cc: 4.15+ <stable@vger.kernel.org> # 4.15+ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org> Reviewed-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Used buffer wasn't big enough to hold whole strings. Example output of
this function is:
[ 0.180892] bcma: bus0: core 0x0800, irq: 2(S)* 3 4 5 6 D I
[ 0.180948] bcma: bus0: core 0x0812, irq: 2(S) 3* 4 5 6 D I
[ 0.180998] bcma: bus0: core 0x082d, irq: 2(S) 3 4* 5 6 D I
[ 0.181046] bcma: bus0: core 0x082c, irq: 2(S) 3 4 5 6 D I*
which means we need to store up to 24 chars.
Fixes: 758f7e06063a8 ("bcma: Use bcma_debug and not pr_cont in MIPS driver") Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Cc: stable@vger.kernel.org # v4.15+ Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Otherwise modules that use these arithmetic operations will fail to
link. We accomplish this with the usual EXPORT_SYMBOL, which on most
architectures goes in the .S file but the ARM64 maintainers prefer that
insead it goes into arm64ksyms.
While we're at it, we also fix this up to use SPDX, and I personally
choose to relicense this as GPL2||BSD so that these symbols don't need
to be export_symbol_gpl, so all modules can use the routines, since
these are important general purpose compiler-generated function calls.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Reported-by: PaX Team <pageexec@freemail.hu> Cc: stable@vger.kernel.org Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In commit 97548575bef3 ("mmc: block: Convert RPMB to a character device") a
new function `mmc_rpmb_ioctl` was added. The final return is simply
returning a value of `0` instead of propagating the correct return code.
Discovered during a compilation with W=1, silence the following gcc warning
drivers/mmc/core/block.c:2470:6: warning: variable ‘ret’ set but not used
[-Wunused-but-set-variable]
Signed-off-by: Mathieu Malaterre <malat@debian.org> Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com> Fixes: 97548575bef3 ("mmc: block: Convert RPMB to a character device") Cc: stable@vger.kernel.org # v4.15+ Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Jun Wu at Facebook reported that an internal service was seeing a return
value of 1 from ftruncate() on Btrfs in some cases. This is coming from
the NEED_TRUNCATE_BLOCK return value from btrfs_truncate_inode_items().
btrfs_truncate() uses two variables for error handling, ret and err.
When btrfs_truncate_inode_items() returns non-zero, we set err to the
return value. However, NEED_TRUNCATE_BLOCK is not an error. Make sure we
only set err if ret is an error (i.e., negative).
To reproduce the issue: mount a filesystem with -o compress-force=zstd
and the following program will encounter return value of 1 from
ftruncate:
int main(void) {
char buf[256] = { 0 };
int ret;
int fd;
"VFS: don't keep disconnected dentries on d_anon" had a non-trivial
side-effect - d_unhashed() now returns true for those dentries,
making d_find_alias() skip them altogether. For most of its callers
that's fine - we really want a connected alias there. However,
there is a codepath where we relied upon picking such aliases
if nothing else could be found - selinux delayed initialization
of contexts for inodes on already mounted filesystems used to
rely upon that.
Cc: stable@kernel.org # f1ee616214cb "VFS: don't keep disconnected dentries on d_anon" Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The debug definitions were missing for MACH_JZ4770, resulting in a build
failure when DEBUG_ZBOOT was set.
Since the UART addresses are the same across all Ingenic SoCs, we just
use a #ifdef CONFIG_MACH_INGENIC instead of checking for individual
Ingenic SoCs.
Additionally, I added a #define for the UART0 address in-code and
dropped the <asm/mach-jz4740/base.h> include, for the reason that this
include file is slowly being phased out as the whole platform is being
moved to devicetree.
Commit b35565bb16a5 ("MIPS: generic: Add support for MIPSfpga") added
and its.S file for xilfpga but forgot to add it to
arch/mips/generic/Platform so it is never used.
Fixes: b35565bb16a5 ("MIPS: generic: Add support for MIPSfpga") Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: linux-mips@linux-mips.org Cc: <stable@vger.kernel.org> # 4.15+
Patchwork: https://patchwork.linux-mips.org/patch/19245/ Signed-off-by: James Hogan <jhogan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
A dtb.o is generated from nexys4ddr.dts but this is never used since it
has been moved to mips/generic with commit b35565bb16a5 ("MIPS: generic:
Add support for MIPSfpga").
Fixes: b35565bb16a5 ("MIPS: generic: Add support for MIPSfpga") Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: linux-mips@linux-mips.org Cc: <stable@vger.kernel.org> # 4.15+
Patchwork: https://patchwork.linux-mips.org/patch/19244/ Signed-off-by: James Hogan <jhogan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
tools: sync up .h files with the repective arch and uapi .h files
BugLink: http://bugs.launchpad.net/bugs/1786352
perf wants matching .h files otherwise it complains during the build
process. As these files have been modified over the past few 4.14.y
releases, they are out of sync, so fix that problem by properly copying
the respective versions to the tools/ mirror copies.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[kamal: copied respective versions from local 4.15 tree] Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
SOU primary plane prepare_fb hook depends upon dmabuf_size to pin up BO
(and not call a new vmw_dmabuf_init) when a new fb size is same as
current fb. This was changed in a recent commit which is causing
page_flip to fail on VM with low display memory and multi-mon failure
when cycle monitors from secondary display.
Cc: <stable@vger.kernel.org> # 4.14, 4.16 Fixes: 20fb5a635a0c ("drm/vmwgfx: Unpin the screen object backup buffer when not used") Signed-off-by: Deepak Rawat <drawat@vmware.com> Reviewed-by: Sinclair Yeh <syeh@vmware.com> Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The SPI version of this chip allows several devices to be present on the
same SPI bus via a local address. If this is in action and if the kernel
has debugfs, however, the code attempts to create duplicate entries for
the regmap's debugfs:
mcp23s08 spi1.1: Failed to create debugfs directory
This patch simply assigns a local name matching the device logical
address to the `struct regmap_config`.
No changes are needed for MCP23S18 because that device does not support
any logical addressing. Similarly, I2C devices do not need any action,
either, because they are already different in their I2C address.
A similar problem is present for the pinctrl debugfs instance, but that
one is not addressed by this patch.
The missing last digit of the CONFIG values is added. Looks like a typo
of some sort when comparing to the downstream dt. This fixes
intermittent behavior behaviour of the ethernet controllers.
This patch adds necessary delay for 4.33 firmware to recover after
EMP reset. Without this patch driver occasionally reinitializes
structures too quickly to communicate with firmware after EMP reset
causing AdminQ to timeout.
Signed-off-by: Filip Sadowski <filip.sadowski@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The cache pointer points to the actual memory used by the cache, as the
comparison here is looking for the type of the cache it should check
against cache_type.
Fixes: 1ea975cf1ef5 ("regmap: Add a function to check if a regmap register is cached") Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The used part does contain an eeprom compatible with an Atmel 24c02
chip and it is from NXP, but it is not called 24c02. It's actually a
se97b chip. Adjust the compatible accordingly.
Fixes: 21dd0ece34c2 ("ARM: dts: at91: add devicetree for the Axentia TSE-850") Signed-off-by: Peter Rosin <peda@axentia.se> Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
According to the latest revision 2.00 of the R-Car Gen2 manual, the LVDS
and the bias circuit must be enabled after the LVDS I/O pins are
enabled, not before. Fix the Gen2 LVDS startup sequence accordingly.
While at it, also fix the comment preceding the first LVDCR0 write that
still talks about hardcoding the LVDS mode 0.
According to the latest revisions of the R-Car Gen3 manual, the LVDS mode
must be set before the LVDS I/O pins are enabled, not after -- fix the
Gen3 LVDS startup sequence accordingly.
Fixes: e947eccbeba4 ("drm: rcar-du: Add support for LVDS mode selection") Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
[Updated comment in rcar_du_lvdsenc_start_gen3()]
[Moved Gen2 startup comment update to separate commit]
[Fixed =| typo] Tested-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When resolving a fallback label, check the sk_buff version as it
is possible (e.g. SCTP) to have family = PF_INET6 while
receiving ip_hdr(skb)->version = 4.
Signed-off-by: Richard Haines <richard_c_haines@btinternet.com> Acked-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
eBPF test fails due to verifier failure because log_buf is too small.
Fixed by increasing log_buf size
Signed-off-by: Prashant Bhole <bhole_prashant_q7@lab.ntt.co.jp> Acked-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When we strip the perf binary, dwarf unwind test stop
to work. The reason is that strip will remove static
function symbols, which we need to check for unwind.
This change will keep this test working in cases where
the global symbols are put into dynamic symbol table,
which is the case on x86. It still won't work on powerpc.
Making those 5 local functions global, and adding
'test_dwarf_unwind__' to their names.
Committer testing:
Before:
# perf test dwarf
58: DWARF unwind : Ok
# strip ~/bin/perf
# perf test dwarf
58: DWARF unwind : FAILED!
# perf test -v dwarf
58: DWARF unwind :
--- start ---
test child forked, pid 6590
unwind: thread map already set, dso=/home/acme/bin/perf
<SNIP>
unwind: access_mem addr 0x7ffce6c48098 val 48563f, offset 1144
unwind: test__dwarf_unwind:ip = 0x4a54e5 (0xa54e5)
got: test__dwarf_unwind 0xa54e5, expecting test__dwarf_unwind
unwind: '':ip = 0x4a50bb (0xa50bb)
failed: got unresolved address 0xa50bb
unwind failed
test child finished with -1
---- end ----
DWARF unwind: FAILED!
#
For the cumulative output, we allocate the he_cache array based on the
--max-stack option value and populate it with data from 'callchain_cursor'.
The --max-stack option value does not ensure now the limit for number of
callchain_cursor nodes, so the cumulative iter code will allocate smaller array
than it's actually needed and cause above corruption.
I think the --max-stack limit does not apply here anyway, because we add
callchain data as normal hist entries, while the --max-stack control the limit
of single entry callchain depth.
Using the callchain_cursor.nr as he_cache array count to fix this. Also
removing struct hist_entry_iter::max_stack, because there's no longer any use
for it.
We need more fixes to ensure that the branch stack code follows properly the
logic of --max-stack, which is not the case at the moment.
Original-patch-by: Jin Yao <yao.jin@linux.intel.com> Signed-off-by: Jiri Olsa <jolsa@kernel.org> Reported-by: Jin Yao <yao.jin@linux.intel.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Kan Liang <kan.liang@intel.com> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lkml.kernel.org/r/20180216123619.GA9945@krava Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The symbol search called by machine__find_kernel_symbol_by_name is using
internally arch__compare_symbol_names function to compare 2 symbol
names, because different archs have different ways of comparing symbols.
Mostly for skipping '.' prefixes and similar.
In test 1 when we try to find matching symbols in kallsyms and vmlinux,
by address and by symbol name. When either is found we compare the pair
symbol names by simple strcmp, which is not good enough for reasons
explained in previous paragraph.
On powerpc this can cause lockup, because even thought we found the
pair, the compared names are different and don't match simple strcmp.
Following code path is executed, that leads to lockup:
- we find the pair in kallsyms by sym->start
next_pair:
- we compare the names and it fails
- we find the pair by sym->name
- the pair addresses match so we call goto next_pair
because we assume the names match in this case
Signed-off-by: Jiri Olsa <jolsa@kernel.org> Tested-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> Acked-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: David Ahern <dsahern@gmail.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Fixes: 031b84c407c3 ("perf probe ppc: Enable matching against dot symbols automatically") Link: http://lkml.kernel.org/r/20180215122635.24029-10-jolsa@kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Please note that only from LBRv5 (according to Jiri) onwards, i.e. >=
Skylake is that we'll have the cycles counts in each branch record
entry, so to see the Cycles and IPC columns, and be able to test this
patch, one need a capable hardware.
While applying this I first tested it on a Broadwell class machine and
couldn't get those columns, will add code to the annotate browser to
warn the user about that, i.e. you have branch records, but no cycles,
use a more recent hardware to get the cycles and IPC columns.
Signed-off-by: Jin Yao <yao.jin@linux.intel.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: Jin Yao <yao.jin@intel.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Kan Liang <kan.liang@intel.com> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lkml.kernel.org/r/1517223473-14750-1-git-send-email-yao.jin@linux.intel.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Using Fedora 27 and latest Linux kernel the test case
trace+probe_libc_inet_pton.sh fails again on s390. This time is the
inlining of functions which does not match. After an update of the
glibc (from 2.26-16 to 2.26-24) the output is different
Currently the kdump kernel becomes very slow if 'noapic' is specified.
Normal kernel doesn't have this bug.
Kernel parameter 'noapic' is used to disable IO-APIC in system for
testing or special purpose. Here the root cause is that in kdump
kernel LAPIC is disabled since commit:
522e664644 ("x86/apic: Disable I/O APIC before shutdown of the local APIC")
In this case we need set up through-local-APIC on boot CPU in
setup_local_APIC().
In normal kernel the legacy irq mode is enabled by the BIOS. If
it is virtual wire mode, the local-APIC has been enabled and set as
through-local-APIC.
Though we fixed the regression introduced by commit 522e664644,
to further improve robustness set up the through-local-APIC mode
explicitly, do not rely on the default boot IRQ mode.
Signed-off-by: Baoquan He <bhe@redhat.com> Reviewed-by: Eric W. Biederman <ebiederm@xmission.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: douly.fnst@cn.fujitsu.com Cc: joro@8bytes.org Cc: prarit@redhat.com Cc: uobergfe@redhat.com Link: http://lkml.kernel.org/r/20180214054656.3780-7-bhe@redhat.com
[ Rewrote the changelog. ] Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When mapping external DMA-bufs through the PRIME mmap call, we might be
given an offset which has to be respected. However for the internal DRM
GEM mmap path, we have to ignore the fake mmap offset used to identify
the buffer only. Currently the code always zeroes out vma->vm_pgoff,
which breaks the former.
This patch fixes the problem by moving the vm_pgoff assignment to a
function that is used only for GEM mmap path, so that the PRIME path
retains the original offset.
Cc: Daniel Kurtz <djkurtz@chromium.org> Signed-off-by: Ørjan Eide <orjan.eide@arm.com> Signed-off-by: Tomasz Figa <tfiga@chromium.org> Signed-off-by: Sean Paul <seanpaul@chromium.org> Signed-off-by: Thierry Escande <thierry.escande@collabora.com> Tested-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Heiko Stuebner <heiko@sntech.de> Link: https://patchwork.freedesktop.org/patch/msgid/20180130202913.28724-4-thierry.escande@collabora.com Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The ADVERTISED_Asym_Pause bit was being improperly set when both
rx and tx pause were enabled. When rx and tx are both enabled, only
the ADVERTISED_Pause bit is supposed to be set.
Signed-off-by: Jake Moroni <mail@jakemoroni.com> Acked-by: Madalin Bucur <madalin.bucur@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This patch fixes MOD_SEL1 bit20 and MOD_SEL2 bit20, bit21 pin assignment
for SSI pins group.
This is a correction to the incorrect implementation of MOD_SEL register
pin assignment for R8A7796 SoC specification of R-Car Gen3 Hardware
User's Manual Rev.0.51E or later.
When RCU stall warning triggers, it can print out a lot of messages
while holding spinlocks. If the console device is slow (e.g. an
actual or IPMI serial console), it may end up triggering NMI hard
lockup watchdog like the following.
Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
stmmac_mac_config_rx_queues_routing() incorrectly calls rx_queue_prio()
instead of rx_queue_routing().
This looks like a copy paste issue, since
stmmac_mac_config_rx_queues_prio() already calls rx_queue_prio(),
and both stmmac_mac_config_rx_queues_routing() and
stmmac_mac_config_rx_queues_prio() are very similar in structure.
Fixes: abe80fdc6ee6 ("net: stmmac: RX queue routing configuration") Signed-off-by: Niklas Cassel <niklas.cassel@axis.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If there is a memory allocation error when trying to change an audit
kernel feature value, the ignored allocation error will trigger a NULL
pointer dereference oops on subsequent use of that pointer. Return
instead.
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
[PM: not necessary (other funcs check for NULL), but a good practice] Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
There is a problem with PCMCIA system resume callbacks with respect
to suspend-to-idle in which the ->suspend_noirq() callback may be
invoked after the ->resume_noirq() one without resuming the system
entirely in some cases. This doesn't work for PCMCIA because of
the lack of symmetry between its system suspend and system resume
"noirq" callbacks.
The system resume handling in PCMCIA is split between
socket_early_resume() and socket_late_resume() which are called in
different phases of system resume and both need to run for
socket_suspend() (invoked by the system suspend "noirq" callback)
to work. Specifically, socket_suspend() returns an error when
called after socket_early_resume() without socket_late_resume(),
so if the suspend-to-idle core detects a spurious wakeup event and
attempts to put the system back to sleep, that is aborted by the
error coming from socket_suspend().
Avoid that by using a new socket state flag, SOCKET_IN_RESUME,
to indicate that socket_early_resume() has already run for the
socket in which case socket_suspend() will do minimum handling
and return 0.
This change has been tested on my venerable Toshiba Portege R500
(which is where the problem has been discovered in the first place),
but admittedly I have no PCMCIA cards to test along with the socket
itself.
Fixes: 33e4f80ee69b (ACPI / PM: Ignore spurious SCI wakeups from suspend-to-idle) Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
[linux@dominikbrodowski.net: follow same codepaths for both suspend variants; call ->suspend()] Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Since 517e7a1537a ("ASoC: bcm2835: move to use the clock framework")
the bcm2835-i2s requires a clock as DT property. Unfortunately
the necessary DT change has never been applied. While we are at it
also fix the first PCM register range to cover the PCM_GRAY register.
Fixes: 517e7a1537a ("ASoC: bcm2835: move to use the clock framework") Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Reviewed-by: Eric Anholt <eric@anholt.net> Tested-by: Matthias Reichl <hias@horus.com> Signed-off-by: Eric Anholt <eric@anholt.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
It appears that the single port Ether controllers having TSU (like SH7734/
R8A7740) need the same kind of treating in sh_eth_tsu_init() as R7S72100
currently has -- they also don't have the TSU registers related e.g. to
passing the frames between ports. Add the 'sh_eth_cpu_data::dual_port'
flag and use it as a new criterion for taking a "short path" in the TSU
init sequence in order to avoid writing to the non-existent registers...
Fixes: f0e81fecd4f8 ("net: sh_eth: Add support SH7734") Fixes: 73a0d907301e ("net: sh_eth: add support R8A7740") Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Tested-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
On hardware which supports timestamping all packets, the timestamps are
recorded in the packet buffer, and the driver no longer uses or reads
the registers. This makes the logic for checking and clearing Rx
timestamp hangs meaningless.
If we run the ixgbe_ptp_rx_hang() function in this case, then the driver
will continuously spam the log output with "Clearing Rx timestamp hang".
These messages are spurious, and confusing to end users.
The original code in commit a9763f3cb54c ("ixgbe: Update PTP to support
X550EM_x devices", 2015-12-03) did have a flag PTP_RX_TIMESTAMP_IN_REGISTER
which was intended to be used to avoid the Rx timestamp hang check,
however it did not actually check the flag before calling the function.
Do so now in order to stop the checks and prevent the spurious log
messages.
Fixes: a9763f3cb54c ("ixgbe: Update PTP to support X550EM_x devices", 2015-12-03) Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Currently when UDF filesystem is recorded without uid / gid (ids are set
to -1), we will assign INVALID_[UG]ID to vfs inode unless user uses uid=
and gid= mount options. In such case filesystem could not be modified in
any way as VFS refuses to modify files with invalid ids (even by root).
This is confusing to users and not very useful default since such media
mode is generally used for removable media. Use overflow[ug]id instead
so that at least root can modify the filesystem.
Reported-by: Steve Kenton <skenton@ou.edu> Reviewed-by: Pali Rohár <pali.rohar@gmail.com> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
An issue in the code mapping the skb fragments into
scatter-gather frames was evidentiated by netperf
TCP_SENDFILE tests. The size was set wrong for all
fragments but the first, affecting the transmission
of any skb with more than one fragment.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Ideally the de-allocation of resources should happen in the exact
opposite order in which they were allocated. It helps maintain the code
in long term, even if nothing really breaks with incorrect ordering.
That wasn't followed in cpufreq_online() and it has some
inconsistencies. For example, the symlinks were created from within
the locked region while they are removed only after putting the locks.
Also ->exit() should have been called only after the symlinks are
removed and the lock is dropped, as that was the case when ->init()
was first called.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
[ rjw: Subject ] Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
A dma_wmb() is used to guarantee the ordering, with respect to
other writes, to cache coherent DMA memory.
There is a dma_wmb() in prepare_tx_desc()/prepare_tso_tx_desc() which
ensures that TDES0/1/2 is written before TDES3 (which contains the own
bit), for First Desc.
However, in the rare case that MSS changes, there will be a MSS
context descriptor in front of the regular DMA descriptors:
Thus, for this special case, we need a dma_wmb()
after prepare_tso_tx_desc()/before writing the own bit to the MSS desc,
so that we flush the write to TDES3 for First Desc,
in order to ensure that the MSS descriptor is the last descriptor to
set the own bit.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
According to Documentation/memory-barriers.txt, we need to use a
dma_rmb() after reading the status/own bit, to ensure that all
descriptor fields are read after reading the own bit.
This way, we ensure that the DMA engine is done with the DMA
descriptor before we read the other descriptor fields, e.g. reading
the tx hardware timestamp (if PTP is enabled).
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
issue:
sometime GFX/MM ib test hit timeout under SRIOV env, root cause
is that engine doesn't come back soon enough so the current
IB test considered as timed out.
fix:
for SRIOV GFX IB test wait time need to be expanded a lot during
SRIOV runtimei mode since it couldn't really begin before GFX engine
come back.
for SRIOV MM IB test it always need more time since MM scheduling
is not go together with GFX engine, it is controled by h/w MM
scheduler so no matter runtime or exclusive mode MM IB test
always need more time.
v2:
use ring type instead of idx to judge
Signed-off-by: Monk Liu <Monk.Liu@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
otherwise there will be DMAR reading error comes out from CP since
GFX is still alive and CPC's WPTR_POLL is still enabled, which would
lead to DMAR read error.
fix:
we can hault CPG after hw_fini, but cannot halt CPC becaues KIQ
stil need to be alive to let RLCV invoke, but its WPTR_POLL could
be disabled.
Signed-off-by: Monk Liu <Monk.Liu@amd.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
There's no reason to delay initialization of most of the driver (such as
mapping memory I/O, getting clocks or enabling runtime PM) to the
component master bind handler.
This additionally fixes a real PM issue caused enabling runtime PM in
the bind handler.
The bind handler performs the following sequence of PM operations:
pm_runtime_enable(dev);
pm_runtime_get_sync(dev);
... (access the hardware to read the device revision) ...
pm_runtime_put_sync(dev);
If a failure occurs at this point, the error path calls
pm_runtime_disable() to balance the pm_runtime_enable() call.
To understand the problem, it should be noted that the bind handler is
called when one of the component registers itself, which happens in the
component's probe handler. Furthermore, as the components are children
of the DSS, the device core calls pm_runtime_get_sync() on the DSS
platform device before calling the component's probe handler. This
increases the DSS power usage count but doesn't runtime resume the
device, as runtime PM is disabled at that point.
The bind handler is thus called with runtime PM disabled, with the
device runtime suspended, but with the power usage count larger than 0.
The pm_runtime_get_sync() call will thus further increase the power
usage count and runtime resume the device. The pm_runtime_put_sync()
handler will decrease the power usage count to a non-zero value and will
thus not suspend the device. Finally, the pm_runtime_disable() call will
disable runtime PM, preventing the pm_runtime_put() call in the device
core from runtime suspending the device. The DSS device is thus left
powered on.
To fix this, move the initialization code from the bind handler to the
probe handler.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When Linux is master of BAM, it can directly read registers to know number
of supported channels, however when its remotely controlled reading these
registers would trigger a crash if the BAM is not yet initialized or
powered up on the remote side.
This patch allows driver to read num-channels and num-ees from Device Tree
for remotely controlled BAM.
vfio-ccw only supports command mode for channel programs, not transport
mode. User space is supposed to already take care of that and pass us
command-mode ORBs only, but better make sure and return an error to
the caller instead of trying to process tcws as ccws.
Reviewed-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com> Acked-by: Halil Pasic <pasic@linux.vnet.ibm.com> Signed-off-by: Cornelia Huck <cohuck@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When dt_to_map_one_config() is called with a pinctrl_dev passed
in, it should only be using this if the node being looked up
is a hog. The code was always using the passed pinctrl_dev
without checking whether the dt node referred to it.
A pin controller can have pinctrl-n dependencies on other pin
controllers in these cases:
- the pin controller hardware is external, for example I2C, so
needs other pin controller(s) to be setup to communicate with
the hardware device.
- it is a child of a composite MFD so its of_node is shared with
the parent MFD and other children of that MFD. Any part of that
MFD could have dependencies on other pin controllers.
Because of this, dt_to_map_one_config() can't assume that if it
has a pinctrl_dev passed in then the node it looks up must be
a hog. It could be a reference to some other pin controller.
If devm_reset_control_get_exclusive() fails, asm9260_wdt_probe()
returns immediately. But clks has been already enabled at that point,
so it is required to disable them or to move the code around.
Found by Linux Driver Verification project (linuxtesting.org).
This patch fixes an issue that a race condition happens between a client
driver and the rcar-dmac driver:
- The rcar_dmac_isr_transfer_end() is called.
- The done list appears, and desc.running is the next active list.
- rcar_dmac_chan_get_residue() is called by a client driver before
rcar_dmac_isr_channel_thread() is called.
- The rcar_dmac_chan_get_residue() will not find any descriptors.
- And, the following WARNING happens:
WARN(1, "No descriptor for cookie!");
The sh-sci driver with HSCIF (921,600bps) on R-Car H3 can cause this
situation.
So, this patch checks the done lists in rcar_dmac_chan_get_residue()
and returns zero if the done lists has the argument cookie.
When booting up with "threadirqs" in command line, all irq handlers of the DMA
controller pl330 will be threaded forcedly. These threads will race for the same
list, pl330->req_done.
Before the callback, the spinlock was released. And after it, the spinlock was
taken. This opened an race window where another threaded irq handler could steal
the spinlock and be permitted to delete entries of the list, pl330->req_done.
If the later deleted an entry that was still referred to by the former, there would
be a kernel panic when the former was scheduled and tried to get the next sibling
of the deleted entry.
The scenario could be depicted as below:
Thread: T1 pl330->req_done Thread: T2
| | |
| -A-B-C-D- |
Locked | |
| | Waiting
Del A | |
| -B-C-D- |
Unlocked | |
| | Locked
Waiting | |
| | Del B
| | |
| -C-D- Unlocked
Waiting | |
|
Locked
|
get C via B
\
- Kernel panic
This patch fixes the below warnings with new glibc and gcc:
hv_vss_daemon.c:100:13: warning: In the GNU C Library, "major" is defined
by <sys/sysmacros.h>. For historical compatibility, it is currently
defined by <sys/types.h> as well, but we plan to remove this soon.
To use "major", include <sys/sysmacros.h> directly.
hv_fcopy_daemon.c:42:2: note: 'snprintf' output between 2 and 1040
bytes into a destination of size 260
Signed-off-by: Dexuan Cui <decui@microsoft.com> Cc: Stephen Hemminger <sthemmin@microsoft.com> Cc: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Then no picture. Apparently the I2C engine inside the SiI9022
is not smart enough to try to fall back to DDC I2C. Or the
vendor have not integrated the electronics properly. I don't
know which one it is.
After this, the I2C bus seems stalled and the first attempt to
read the status register fails, and the code returns with
negative return value, and the display fails to initialized.
Instead, retry status readout five times and continue even
if this fails.
Tested on the ARM Versatile Express with a DVI-to-VGA
connector, it now gives picture.
Introduce a helper struct device *dev variable to make
the code more readable.
Pipe clock comes out of the phy and is available as long as
the phy is turned on. Clock controller fails to gate this
clock after the phy is turned off and generates a warning.
In slave_update() of vmaster code ignores the error from the slave
get() callback and copies the values. It's not only about the missing
error code but also that this may potentially lead to a leak of
uninitialized variables when the slave get() don't clear them.
This patch fixes slave_update() not to copy the potentially
uninitialized values when an error is returned from the slave get()
callback, and to propagate the error value properly.