Probe responses were sent to the multicast station while
they should be routed to the broadcast station.
This has no negative effect since the frame was still
routed to the right queue, but it looked very fishy
to send a frame to a (queue, station) tuple where
'queue' is not mapped to 'station'.
Fixes: 7c305de2b954 ("iwlwifi: mvm: Direct multicast frames to the correct station") Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
As reported by the OpenWRT team, write requests sometimes fail on some
platforms.
Currently to check the state chip_ready() is used correctly as described by
the flash memory S29GL256P11TFI01 datasheet.
Also chip_good() is used to check if the write is succeeded and it was
implemented by the commit fb4a90bfcd6d8 ("[MTD] CFI-0002 - Improve error
checking").
But actually the write failure is caused on some platforms and also it can
be fixed by using chip_good() to check the state and retry instead.
Also it seems that it is caused after repeated about 1,000 times to retry
the write one word with the reset command.
By using chip_good() to check the state to be done it can be reduced the
retry with reset.
It is depended on the actual flash chip behavior so the root cause is
unknown.
The syzbot fuzzer has reported a pair of problems in the
hidraw_ioctl() function: slab-out-of-bounds read and use-after-free
read. An example of the first:
BUG: KASAN: slab-out-of-bounds in strlen+0x79/0x90 lib/string.c:525
Read of size 1 at addr ffff8881c8035f38 by task syz-executor.4/2833
It turns out the fault was caused by a bug in the HID Logitech driver,
which violates the requirement that every pathway calling
hid_hw_start() must also call hid_hw_stop(). This patch fixes the bug
by making sure the requirement is met.
Reported-and-tested-by: syzbot+3cbe5cd105d2ad56a1df@syzkaller.appspotmail.com Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: <stable@vger.kernel.org> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The sony driver is not properly cleaning up from potential failures in
sony_input_configured. Currently it calls hid_hw_stop, while hid_connect
is still running. This is not a good idea, instead hid_hw_stop should
be moved to sony_probe. Similar changes were recently made to Logitech
drivers, which were also doing improper cleanup.
The syzbot fuzzer provoked a general protection fault in the
hid-prodikeys driver:
kasan: CONFIG_KASAN_INLINE enabled
kasan: GPF could be caused by NULL-ptr deref or user memory access
general protection fault: 0000 [#1] SMP KASAN
CPU: 0 PID: 12 Comm: kworker/0:1 Not tainted 5.3.0-rc5+ #28
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
Workqueue: usb_hub_wq hub_event
RIP: 0010:pcmidi_submit_output_report drivers/hid/hid-prodikeys.c:300 [inline]
RIP: 0010:pcmidi_set_operational drivers/hid/hid-prodikeys.c:558 [inline]
RIP: 0010:pcmidi_snd_initialise drivers/hid/hid-prodikeys.c:686 [inline]
RIP: 0010:pk_probe+0xb51/0xfd0 drivers/hid/hid-prodikeys.c:836
Code: 0f 85 50 04 00 00 48 8b 04 24 4c 89 7d 10 48 8b 58 08 e8 b2 53 e4 fc
48 8b 54 24 20 48 b8 00 00 00 00 00 fc ff df 48 c1 ea 03 <80> 3c 02 00 0f
85 13 04 00 00 48 ba 00 00 00 00 00 fc ff df 49 8b
The problem is caused by the fact that pcmidi_get_output_report() will
return an error if the HID device doesn't provide the right sort of
output report, but pcmidi_set_operational() doesn't bother to check
the return code and assumes the function call always succeeds.
This patch adds the missing check and aborts the probe operation if
necessary.
Reported-and-tested-by: syzbot+1088533649dafa1c9004@syzkaller.appspotmail.com Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: <stable@vger.kernel.org> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The upstream kernel commit cited below modified the workqueue in the
new CQ API to be bound to a specific CPU (instead of being unbound).
This caused ALL users of the new CQ API to use the same bound WQ.
Specifically, MAD handling was severely delayed when the CPU bound
to the WQ was busy handling (higher priority) interrupts.
This caused a delay in the MAD "heartbeat" response handling,
which resulted in ports being incorrectly classified as "down".
To fix this, add a new "unbound" WQ type to the new CQ API, so that users
have the option to choose either a bound WQ or an unbound WQ.
For MADs, choose the new "unbound" WQ.
Fixes: b7363e67b23e ("IB/device: Convert ib-comp-wq to be CPU-bound") Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Leon Romanovsky <leonro@mellanox.com> Reviewed-by: Sagi Grimberg <sagi@grimberg.m> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
There's a bug in skiboot that causes the OPAL_XIVE_ALLOCATE_IRQ call
to return the 32-bit value 0xffffffff when OPAL has run out of IRQs.
Unfortunatelty, OPAL return values are signed 64-bit entities and
errors are supposed to be negative. If that happens, the linux code
confusingly treats 0xffffffff as a valid IRQ number and panics at some
point.
A fix was recently merged in skiboot:
e97391ae2bb5 ("xive: fix return value of opal_xive_allocate_irq()")
but we need a workaround anyway to support older skiboots already
in the field.
Internally convert 0xffffffff to OPAL_RESOURCE which is the usual error
returned upon resource exhaustion.
Cc: stable@vger.kernel.org # v4.12+ Signed-off-by: Greg Kurz <groug@kaod.org> Reviewed-by: Cédric Le Goater <clg@kaod.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/156821713818.1985334.14123187368108582810.stgit@bahia.lan
(groug: fix arch/powerpc/platforms/powernv/opal-wrappers.S instead of
non-existing arch/powerpc/platforms/powernv/opal-call.c) Signed-off-by: Greg Kurz <groug@kaod.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
There are devices which require low connection intervals for usable operation
including keyboards and mice. Forcing a static connection interval for
these types of devices has an impact in latency and causes a regression.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Observed crash in some scenarios when assertion has occurred,
this is because hw structure is freed and is tried to get
accessed in some functions where null check is already
present. So, avoided the crash by making the hw to NULL after
freeing.
Signed-off-by: Sanjay Konduri <sanjay.konduri@redpinesignals.com> Signed-off-by: Sushant Kumar Mishra <sushant.mishra@redpinesignals.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
(cherry picked from commit abd39c6ded9db53aa44c2540092bdd5fb6590fa8) Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Acked-by: Tyler Hicks <tyhicks@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Nicolas Dichtel [Fri, 6 Sep 2019 09:54:00 +0000 (11:54 +0200)]
ipv6: fix neighbour resolution with raw socket
BugLink: https://bugs.launchpad.net/bugs/1834465
The scenario is the following: the user uses a raw socket to send an ipv6
packet, destinated to a not-connected network, and specify a connected nh.
Here is the corresponding python script to reproduce this scenario:
fd00:175::/64 is a connected route and fd00:200::fa is not a connected
host.
With this scenario, the kernel starts by sending a NS to resolve
fd00:175::2. When it receives the NA, it flushes its queue and try to send
the initial packet. But instead of sending it, it sends another NS to
resolve fd00:200::fa, which obvioulsy fails, thus the packet is dropped. If
the user sends again the packet, it now uses the right nh (fd00:175::2).
The problem is that ip6_dst_lookup_neigh() uses the rt6i_gateway, which is
:: because the associated route is a connected route, thus it uses the dst
addr of the packet. Let's use rt6_nexthop() to choose the right nh.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net>
(backported from commit 2c6b55f45d53420d8310d41310e0e2cd41fe073f)
[nicolas.dichtel:
The upstream patch was slightly modified because ip6_dst_lookup_neigh()
does not exist in v4.15. It has been introduced in v4.18 by the upstream
commit f8a1b43b709d ("net/ipv6: Create a neigh_lookup for FIB entries"). In
fact, ip6_dst_lookup_neigh() just calls ip6_neigh_lookup().] Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
rt6_nexthop() will be used by ip6_dst_lookup_neigh(), which uses const
variables.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Reported-by: kbuild test robot <lkp@intel.com> Acked-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
(backported from commit 9b1c1ef13b35fa35051b635ca9fbda39fe6bbc70) Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
UBUNTU: SAUCE: selftests: net: replace AF_MAX with INT_MAX in socket.c
BugLink: https://bugs.launchpad.net/bugs/1842023
Use INT_MAX instead of AF_MAX, since libc might have a smaller value
of AF_MAX than the kernel, what causes the test to fail.
Signed-off-by: Marcelo Henrique Cerri <marcelo.cerri@canonical.com> Acked-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Hui Wang [Mon, 2 Sep 2019 04:28:00 +0000 (06:28 +0200)]
ALSA: hda - Define a fallback_pin_fixup_tbl for alc269 family
BugLink: https://bugs.launchpad.net/bugs/1842265
We have another Dell laptop which needs the DELL4_MIC_NO_PRESENCE,
and this laptop has different pincfg definitions from existing
ones in the pintbl, rather adding a new entry, let us define
a tbl in the fallback_pin_fixup_tbl and this tbl will match
all dell machines with alc289 codec and the pins of 0x19 and 0x1b
are undef by default.
Signed-off-by: Hui Wang <hui.wang@canonical.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
(backported from commit 7c0a69394c265f2bb674c3f5daadfdd5c15ea0d1) Signed-off-by: Hui Wang <hui.wang@canonical.com> Acked-by: Seth Forshee <seth.forshee@canonical.com> Acked-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Hui Wang [Mon, 2 Sep 2019 04:28:00 +0000 (06:28 +0200)]
ALSA: hda - Expand pin_match function to match upcoming new tbls
BugLink: https://bugs.launchpad.net/bugs/1842265
With the existing pintbl, we already have many entries in it. it is
better to figure out a new way to reduce the size of the pintbl.
We plan to define a new tbl which will match more machines with a
single tbl, To do that, this function doesn't need to match all valid
pins between machine and tbl, it just needs to match all pins defined
in the tbl with the machine.
And the plan is to move some tbls from pin_fixup_tbl to
fallback_pin_fixup_tbl gradually.
Signed-off-by: Hui Wang <hui.wang@canonical.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
(backported from commit 0fc1e447e9e474c2460df8d0378f899b8813e1d2) Signed-off-by: Hui Wang <hui.wang@canonical.com> Acked-by: Seth Forshee <seth.forshee@canonical.com> Acked-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
UBUNTU: SAUCE: kbuild: add -fcf-protection=none when using retpoline flags
BugLink: https://bugs.launchpad.net/bugs/1843291
The gcc -fcf-protection=branch option is not compatible with
-mindirect-branch=thunk-extern. The latter is used when
CONFIG_RETPOLINE is selected, and this will fail to build with
a gcc which has -fcf-protection=branch enabled by default. Adding
-fcf-protection=none when building with retpoline enabled
prevents such build failures.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
(cherry picked from commit 29be86d7f9cb18df4123f309ac7857570513e8bc) Signed-off-by: Seth Forshee <seth.forshee@canonical.com> Acked-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Acked-by: Colin Ian King <colin.king@canonical.com> Acked-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
BugLink: https://bugs.launchpad.net/bugs/1842774
Add detection for machine types 0x8562 and 8x8561 and set the ELF platform
name to z15. Add the miscellaneous-instruction-extension 3 facility to
the list of facilities for z15.
And allow to generate code that only runs on a z15 machine.
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
(cherry picked from commit a0e2251132995b962281aa80ab54a9288f9e0b6b) Signed-off-by: Frank Heimes <frank.heimes@canonical.com> Acked-by: Sultan Alsawaf <sultan.alsawaf@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
On embedded environments with hard memory limits it is a normal although
rare case when skb can't be allocated on rx part under high traffic.
In such OOM cases napi_complete_done() was not called.
So the napi object became in an invalid state like it is "scheduled".
Kernel do not re-schedules the poll of that napi object.
Consequently, kernel can not remove that object the system hangs on
`ifconfig down` waiting for a poll.
We are fixing this by gracefully closing napi poll routine with correct
invocation of napi_complete_done.
This was reproduced with artificially failing the allocation of skb to
simulate an "out of memory" error case and check that traffic does
not get stuck.
Fixes: 970a2e9864b0 ("net: ethernet: aquantia: Vector operations") Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com> Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Currently, the ibmvnic driver will not schedule device resets
if the device is being removed, but does not check the device
state before the reset is actually processed. This leads to a race
where a reset is scheduled with a valid device state but is
processed after the driver has been removed, resulting in an oops.
Fix this by checking the device state before processing a queued
reset event.
Reported-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com> Tested-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com> Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Simplify the check in physdev_mt_check() to emit an error message
only when passed an invalid chain (ie, NF_INET_LOCAL_OUT).
This avoids cluttering up the log with errors against valid rules.
For large/heavily modified rulesets, current behavior can quickly
overwhelm the ring buffer, because this function gets called on
every change, regardless of the rule that was changed.
When showing metadata about a single program by invoking
"bpftool prog show PROG", the file descriptor referring to the program
is not closed before returning from the function. Let's close it.
Christoph Paasch [Fri, 13 Sep 2019 20:08:19 +0000 (13:08 -0700)]
tcp: Don't dequeue SYN/FIN-segments from write-queue
BugLink: https://bugs.launchpad.net/bugs/1845266
If a SYN/FIN-segment is on the write-queue, skb->len is 0, but the
segment actually has been transmitted. end_seq and seq of the tcp_skb_cb
in that case will indicate this difference.
We should not remove such segments from the write-queue as we might be
in SYN_SENT-state and a retransmission-timer is running. When that one
fires, packets_out will be 1, but the write-queue would be empty,
resulting in:
The problem is that we are removing an skb from the write-queue that
could have been referenced by the sk_send_head. Thus, we need to check
for the send_head's sanity after removing it.
This patch needs to be backported only to 4.14 and older (among those
that applied the backport of fdfc5c8594c2).
Fixes: fdfc5c8594c2 ("tcp: remove empty skb from write queue in error cases") Cc: Eric Dumazet <edumazet@google.com> Cc: Jason Baron <jbaron@akamai.com> Cc: Vladimir Rutsky <rutsky@google.com> Cc: Soheil Hassas Yeganeh <soheil@google.com> Cc: Neal Cardwell <ncardwell@google.com> Signed-off-by: Christoph Paasch <cpaasch@apple.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Commmit eab09532d400 ("binfmt_elf: use ELF_ET_DYN_BASE only for PIE"),
made changes in the rare case when the ELF loader was directly invoked
(e.g to set a non-inheritable LD_LIBRARY_PATH, testing new versions of
the loader), by moving into the mmap region to avoid both ET_EXEC and
PIE binaries. This had the effect of also moving the brk region into
mmap, which could lead to the stack and brk being arbitrarily close to
each other. An unlucky process wouldn't get its requested stack size
and stack allocations could end up scribbling on the heap.
This is illustrated here. In the case of using the loader directly, brk
(so helpfully identified as "[heap]") is allocated with the _loader_ not
the binary. For example, with ASLR entirely disabled, you can see this
more clearly:
The solution is to move brk out of mmap and into ELF_ET_DYN_BASE since
nothing is there in the direct loader case (and ET_EXEC is still far
away at 0x400000). Anything that ran before should still work (i.e.
the ultimately-launched binary already had the brk very far from its
text, so this should be no different from a COMPAT_BRK standpoint). The
only risk I see here is that if someone started to suddenly depend on
the entire memory space lower than the mmap region being available when
launching binaries via a direct loader execs which seems highly
unlikely, I'd hope: this would mean a binary would _not_ work when
exec()ed normally.
(Note that this is only done under CONFIG_ARCH_HAS_ELF_RANDOMIZATION
when randomization is turned on.)
Link: http://lkml.kernel.org/r/20190422225727.GA21011@beast Link: https://lkml.kernel.org/r/CAGXu5jJ5sj3emOT2QPxQkNQk0qbU6zEfu9=Omfhx_p0nCKPSjA@mail.gmail.com Fixes: eab09532d400 ("binfmt_elf: use ELF_ET_DYN_BASE only for PIE") Signed-off-by: Kees Cook <keescook@chromium.org> Reported-by: Ali Saidi <alisaidi@amazon.com> Cc: Ali Saidi <alisaidi@amazon.com> Cc: Guenter Roeck <linux@roeck-us.net> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Jann Horn <jannh@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: Frank van der Linden <fllinden@amazon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The PCI kirin driver compilation produces the following section mismatch
warning:
WARNING: vmlinux.o(.text+0x4758cc): Section mismatch in reference from
the function kirin_pcie_probe() to the function
.init.text:kirin_add_pcie_port()
The function kirin_pcie_probe() references
the function __init kirin_add_pcie_port().
This is often because kirin_pcie_probe lacks a __init
annotation or the annotation of kirin_add_pcie_port is wrong.
Remove '__init' from kirin_add_pcie_port() to fix it.
Fixes: fc5165db245a ("PCI: kirin: Add HiSilicon Kirin SoC PCIe controller driver") Reported-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
[lorenzo.pieralisi@arm.com: updated commit log] Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
After the conversion to lock-less dma-api call the
increase_address_space() function can be called without any
locking. Multiple CPUs could potentially race for increasing
the address space, leading to invalid domain->mode settings
and invalid page-tables. This has been happening in the wild
under high IO load and memory pressure.
Fix the race by locking this operation. The function is
called infrequently so that this does not introduce
a performance regression in the dma-api path again.
Reported-by: Qian Cai <cai@lca.pw> Fixes: 256e4621c21a ('iommu/amd: Make use of the generic IOVA allocator') Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When devices are attached to the amd_iommu in a kdump kernel, the old device
table entries (DTEs), which were copied from the crashed kernel, will be
overwritten with a new domain number. When the new DTE is written, the IOMMU
is told to flush the DTE from its internal cache--but it is not told to flush
the translation cache entries for the old domain number.
Without this patch, AMD systems using the tg3 network driver fail when kdump
tries to save the vmcore to a network system, showing network timeouts and
(sometimes) IOMMU errors in the kernel log.
This patch will flush IOMMU translation cache entries for the old domain when
a DTE gets overwritten with a new domain number.
Signed-off-by: Stuart Hayes <stuart.w.hayes@gmail.com> Fixes: 3ac3e5ee5ed5 ('iommu/amd: Copy old trans table from old kernel') Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If a request_key authentication token key gets revoked, there's a window in
which request_key_auth_describe() can see it with a NULL payload - but it
makes no check for this and something like the following oops may occur:
When the 'start' parameter is >= 0xFF000000 on 32-bit
systems, or >= 0xFFFFFFFF'FF000000 on 64-bit systems,
fill_gva_list() gets into an infinite loop.
With such inputs, 'cur' overflows after adding HV_TLB_FLUSH_UNIT
and always compares as less than end. Memory is filled with
guest virtual addresses until the system crashes.
Fix this by never incrementing 'cur' to be larger than 'end'.
Reported-by: Jong Hyun Park <park.jonghyun@yonsei.ac.kr> Signed-off-by: Tianyu Lan <Tianyu.Lan@microsoft.com> Reviewed-by: Michael Kelley <mikelley@microsoft.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Fixes: 2ffd9e33ce4a ("x86/hyper-v: Use hypercall for remote TLB flush") Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Identical to __put_user(); the __get_user() argument evalution will too
leak UBSAN crud into the __uaccess_begin() / __uaccess_end() region.
While uncommon this was observed to happen for:
drivers/xen/gntdev.c: if (__get_user(old_status, batch->status[i]))
where UBSAN added array bound checking.
This complements commit:
6ae865615fc4 ("x86/uaccess: Dont leak the AC flag into __put_user() argument evaluation")
If devm_request_irq() fails to disable all interrupts, no cleanup is
performed before retuning the error. To fix this issue, invoke
omap_dma_free() to do the cleanup.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu> Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Link: https://lore.kernel.org/r/1565938570-7528-1-git-send-email-wenwen@cs.uga.edu Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In ti_dra7_xbar_probe(), 'rsv_events' is allocated through kcalloc(). Then
of_property_read_u32_array() is invoked to search for the property.
However, if this process fails, 'rsv_events' is not deallocated, leading to
a memory leak bug. To fix this issue, free 'rsv_events' before returning
the error.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu> Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Link: https://lore.kernel.org/r/1565938136-7249-1-git-send-email-wenwen@cs.uga.edu Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In commit 99cd149efe82 ("sgiseeq: replace use of dma_cache_wback_inv"),
a call to 'get_zeroed_page()' has been turned into a call to
'dma_alloc_coherent()'. Only the remove function has been updated to turn
the corresponding 'free_page()' into 'dma_free_attrs()'.
The error hndling path of the probe function has not been updated.
Fix it now.
Rename the corresponding label to something more in line.
Fixes: 99cd149efe82 ("sgiseeq: replace use of dma_cache_wback_inv") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Reviewed-by: Thomas Bogendoerfer <tbogendoerfer@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
turbostat could be terminated by general protection fault on some latest
hardwares which (for example) support 9 levels of C-states and show 18
"tADDED" lines. That bloats the total output and finally causes buffer
overrun. So let's extend the buffer to avoid this.
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The -w argument in x86_energy_perf_policy currently triggers an
unconditional segfault.
This is because the argument string reads: "+a:c:dD:E:e:f:m:M:rt:u:vw" and
yet the argument handler expects an argument.
When parse_optarg_string is called with a null argument, we then proceed to
crash in strncmp, not horribly friendly.
The man page describes -w as taking an argument, the long form
(--hwp-window) is correctly marked as taking a required argument, and the
code expects it.
As such, this patch simply marks the short form (-w) as requiring an
argument.
Signed-off-by: Zephaniah E. Loss-Cutler-Hull <zephaniah@gmail.com> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
x86_energy_perf_policy first uses __get_cpuid() to check the maximum
CPUID level and exits if it is too low. It then assumes that later
calls will succeed (which I think is architecturally guaranteed). It
also assumes that CPUID works at all (which is not guaranteed on
x86_32).
If optimisations are enabled, gcc warns about potentially
uninitialized variables. Fix this by adding an exit-on-error after
every call to __get_cpuid() instead of just checking the maximum
level.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When counting dispatched micro-ops with cnt_ctl=1, in order to prevent
sample bias, IBS hardware preloads the least significant 7 bits of
current count (IbsOpCurCnt) with random values, such that, after the
interrupt is handled and counting resumes, the next sample taken
will be slightly perturbed.
The current count bitfield is in the IBS execution control h/w register,
alongside the maximum count field.
Currently, the IBS driver writes that register with the maximum count,
leaving zeroes to fill the current count field, thereby overwriting
the random bits the hardware preloaded for itself.
Fix the driver to actually retain and carry those random bits from the
read of the IBS control register, through to its write, instead of
overwriting the lower current count bits with zeroes.
Tested with:
perf record -c 100001 -e ibs_op/cnt_ctl=1/pp -a -C 0 taskset -c 0 <workload>
Machines prior to family 10h Rev. C don't have the RDWROPCNT capability,
and have the IbsOpCurCnt bitfield reserved, so this patch shouldn't
affect their operation.
It is unknown why commit db98c5faf8cb ("perf/x86: Implement 64-bit
counter support for IBS") ignored the lower 4 bits of the IbsOpCurCnt
field; the number of preloaded random bits has always been 7, AFAICT.
Signed-off-by: Kim Phillips <kim.phillips@amd.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: "Arnaldo Carvalho de Melo" <acme@kernel.org> Cc: <x86@kernel.org> Cc: Ingo Molnar <mingo@kernel.org> Cc: Ingo Molnar <mingo@redhat.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: "Borislav Petkov" <bp@alien8.de> Cc: Stephane Eranian <eranian@google.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: "Namhyung Kim" <namhyung@kernel.org> Cc: "H. Peter Anvin" <hpa@zytor.com> Link: https://lkml.kernel.org/r/20190826195730.30614-1-kim.phillips@amd.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
A similar workaround for the suspend/resume problem is needed for yet
another ASUS machines, P6X models. Like the previous fix, the BIOS
doesn't provide the standard DMI_SYS_* entry, so again DMI_BOARD_*
entries are used instead.
Reported-and-tested-by: SteveM <swm@swm1.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
pfn_valid can be wrong when parsing a invalid pfn whose phys address
exceeds BITS_PER_LONG as the MSB will be trimed when shifted.
The issue originally arise from bellowing call stack, which corresponding to
an access of the /proc/kpageflags from userspace with a invalid pfn parameter
and leads to kernel panic.
[46886.723249] c7 [<c031ff98>] (stable_page_flags) from [<c03203f8>]
[46886.723264] c7 [<c0320368>] (kpageflags_read) from [<c0312030>]
[46886.723280] c7 [<c0311fb0>] (proc_reg_read) from [<c02a6e6c>]
[46886.723290] c7 [<c02a6e24>] (__vfs_read) from [<c02a7018>]
[46886.723301] c7 [<c02a6f74>] (vfs_read) from [<c02a778c>]
[46886.723315] c7 [<c02a770c>] (SyS_pread64) from [<c0108620>]
(ret_fast_syscall+0x0/0x28)
Signed-off-by: Zhaoyang Huang <zhaoyang.huang@unisoc.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
It's safer to zero out the password so that it can never be disclosed.
Fixes: 0c219f5799c7 ("cifs: set domainName when a domain-key is used in multiuser") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When we use a domain-key to authenticate using multiuser we must also set
the domainnmame for the new volume as it will be used and passed to the server
in the NTLMSSP Domain-name.
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Looking at the implementation of get_symbol_pos(), it returns the
lowest index for aliasing symbols. In this case, it return 0.
But kallsyms_lookup_size_offset() considers 0 as a failure, which
is obviously wrong (there is definitely a valid symbol living there).
In turn, the kprobe blacklisting stops abruptly, hence the original
error.
A CONFIG_KALLSYMS_ALL kernel wouldn't fail as there is always
some random symbols at the beginning of this array, which are never
looked up via kallsyms_lookup_size_offset.
Fix it by considering that get_symbol_pos() is always successful
(which is consistent with the other uses of this function).
Fixes: ffc5089196446 ("[PATCH] Create kallsyms_lookup_size_offset()") Reviewed-by: Masami Hiramatsu <mhiramat@kernel.org> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Will Deacon <will@kernel.org> Cc: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Marc Zyngier <maz@kernel.org> Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The find_pattern() debug output was printing the 'skip' character.
This can be a NULL-byte and messes up further pr_debug() output.
Output without the fix:
kernel: nf_conntrack_ftp: Pattern matches!
kernel: nf_conntrack_ftp: Skipped up to `<7>nf_conntrack_ftp: find_pattern `PORT': dlen = 8
kernel: nf_conntrack_ftp: find_pattern `EPRT': dlen = 8
Output with the fix:
kernel: nf_conntrack_ftp: Pattern matches!
kernel: nf_conntrack_ftp: Skipped up to 0x0 delimiter!
kernel: nf_conntrack_ftp: Match succeeded!
kernel: nf_conntrack_ftp: conntrack_ftp: match `172,17,0,100,200,207' (20 bytes at 4150681645)
kernel: nf_conntrack_ftp: find_pattern `PORT': dlen = 8
Signed-off-by: Thomas Jarosch <thomas.jarosch@intra2net.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Rahul Tanwar reported the following bug on DT systems:
> 'ioapic_dynirq_base' contains the virtual IRQ base number. Presently, it is
> updated to the end of hardware IRQ numbers but this is done only when IOAPIC
> configuration type is IOAPIC_DOMAIN_LEGACY or IOAPIC_DOMAIN_STRICT. There is
> a third type IOAPIC_DOMAIN_DYNAMIC which applies when IOAPIC configuration
> comes from devicetree.
>
> See dtb_add_ioapic() in arch/x86/kernel/devicetree.c
>
> In case of IOAPIC_DOMAIN_DYNAMIC (DT/OF based system), 'ioapic_dynirq_base'
> remains to zero initialized value. This means that for OF based systems,
> virtual IRQ base will get set to zero.
Such systems will very likely not even boot.
For DT enabled machines ioapic_dynirq_base is irrelevant and not
updated, so simply map the IRQ base 1:1 instead.
get_registers() blindly copies the memory written to by the
usb_control_msg() call even if the underlying urb failed.
This could lead to junk register values being read by the driver, since
some indirect callers of get_registers() ignore the return values. One
example is:
ocp_read_dword() ignores the return value of generic_ocp_read(), which
calls get_registers().
So, emulate PCI "Master Abort" behavior by setting the buffer to all
0xFFs when usb_control_msg() fails.
This patch is copied from the r8152 driver (v2.12.0) published by
Realtek (www.realtek.com).
Signed-off-by: Prashant Malani <pmalani@chromium.org> Acked-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Multiple batadv_ogm2_packet can be stored in an skbuff. The functions
batadv_v_ogm_send_to_if() uses batadv_v_ogm_aggr_packet() to check if there
is another additional batadv_ogm2_packet in the skb or not before they
continue processing the packet.
The length for such an OGM2 is BATADV_OGM2_HLEN +
batadv_ogm2_packet->tvlv_len. The check must first check that at least
BATADV_OGM2_HLEN bytes are available before it accesses tvlv_len (which is
part of the header. Otherwise it might try read outside of the currently
available skbuff to get the content of tvlv_len.
Fixes: 9323158ef9f4 ("batman-adv: OGMv2 - implement originators logic") Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
A timing hazard exists when an early fork/exec thread begins
exiting and sets its mm pointer to NULL while a separate core
tries to update the section information.
This commit ensures that the mm pointer is not NULL before
setting its section parameters. The arguments provided by
commit 11ce4b33aedc ("ARM: 8672/1: mm: remove tasklist locking
from update_sections_early()") are equally valid for not
requiring grabbing the task_lock around this check.
Fixes: 08925c2f124f ("ARM: 8464/1: Update all mm structures with section adjustments") Signed-off-by: Doug Berger <opendmb@gmail.com> Acked-by: Laura Abbott <labbott@redhat.com> Cc: Mike Rapoport <rppt@linux.ibm.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Rob Herring <robh@kernel.org> Cc: "Steven Rostedt (VMware)" <rostedt@goodmis.org> Cc: Peng Fan <peng.fan@nxp.com> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If qed_mcp_send_drv_version() fails, no cleanup is executed, leading to
memory leaks. To fix this issue, introduce the label 'err4' to perform the
cleanup work before returning the error.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu> Acked-by: Sudarsana Reddy Kalluru <skalluru@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Initialise the result count to 0 rather than initialising it to the
argument count. The reason is that we want to ensure we record the
I/O stats correctly in the case where an error is returned (for
instance in the layoutstats).
Currently, we are translating RPC level errors such as timeouts,
as well as interrupts etc into EOPENSTALE, which forces a single
replay of the open attempt. What we actually want to do is
force the replay only in the cases where the returned error
indicates that the file may have changed on the server.
So the fix is to spell out the exact set of errors where we want
to return EOPENSTALE.
Trying to append nfacct related rules results in an unhelpful message.
Although it is suggested to look for more information in dmesg, nothing
can be found there.
# iptables -A <chain> -m nfacct --nfacct-name <acct-object>
iptables: Invalid argument. Run `dmesg' for more information.
This patch fixes the memory misalignment by enforcing 8-byte alignment
within the struct's first revision. This solution is often used in many
other uapi netfilter headers.
Currently the driver does not handle EPROBE_DEFER for the confd gpio.
Use devm_gpiod_get_optional() instead of devm_gpiod_get() and return
error codes from altera_ps_probe().
Fixes: 5692fae0742d ("fpga manager: Add altera-ps-spi driver for Altera FPGAs") Signed-off-by: Phil Reid <preid@electromag.com.au> Signed-off-by: Moritz Fischer <mdf@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
"p runtime/jit: pass > 32bit index to tail_call" fails when
bpf_jit_enable=1, because the tail call is not executed.
This in turn is because the generated code assumes index is 64-bit,
while it must be 32-bit, and as a result prog array bounds check fails,
while it should pass. Even if bounds check would have passed, the code
that follows uses 64-bit index to compute prog array offset.
Fix by using clrj instead of clgrj for comparing index with array size,
and also by using llgfr for truncating index to 32 bits before using it
to compute prog array offset.
According to the latest am572x[1] and dra74x[2] data manuals, mmc3
default, hs, sdr12 and sdr25 modes use iodelay values given in
MMC3_MANUAL1. Set the MODE_SELECT bit for these so that manual mode is
selected and correct iodelay values can be configured.
We have errata i688 workaround produce warnings on SoCs other than
omap4 and omap5:
omap4_sram_init:Unable to allocate sram needed to handle errata I688
omap4_sram_init:Unable to get sram pool needed to handle errata I688
This is happening because there is no ti,omap4-mpu node, or no SRAM
to configure for the other SoCs, so let's remove the warning based
on the SoC revision checks.
As nobody has complained it seems that the other SoC variants do not
need this workaround.
Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
"masking, test in bounds 3" fails on s390, because
BPF_ALU64_IMM(BPF_NEG, BPF_REG_2, 0) ignores the top 32 bits of
BPF_REG_2. The reason is that JIT emits lcgfr instead of lcgr.
The associated comment indicates that the code was intended to
emit lcgr in the first place, it's just that the wrong opcode
was used.
TRM says PWMSS_SYSCONFIG bit for SOFTRESET changes to zero when
reset is completed. Let's configure it as otherwise we get warnings
on boot when we check the data against dts provided data. Eventually
the legacy platform data will be just dropped, but let's fix the
warning first.
Reviewed-by: Suman Anna <s-anna@ti.com> Tested-by: Keerthy <j-keerthy@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
commit 1222a1601488 ("nl80211: Fix possible Spectre-v1 for CQM
RSSI thresholds") was incomplete and requires one more fix to
prevent accessing to rssi_thresholds[n] because user can control
rssi_thresholds[i] values to make i reach to n. For example,
rssi_thresholds = {-400, -300, -200, -100} when last is -34.
Cc: stable@vger.kernel.org Fixes: 1222a1601488 ("nl80211: Fix possible Spectre-v1 for CQM RSSI thresholds") Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Masashi Honma <masashi.honma@gmail.com> Link: https://lore.kernel.org/r/20190908005653.17433-1-masashi.honma@gmail.com Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
mwifiex_update_vs_ie(),mwifiex_set_uap_rates() and
mwifiex_set_wmm_params() call memcpy() without checking
the destination size.Since the source is given from
user-space, this may trigger a heap buffer overflow.
Fix them by putting the length check before performing memcpy().
This fix addresses CVE-2019-14814,CVE-2019-14815,CVE-2019-14816.
Signed-off-by: Wen Huang <huangwenabc@gmail.com> Acked-by: Ganapathi Bhat <gbhat@marvell.comg> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When half-duplex RS485 communication is used, after RX is started, TX
tasklet still needs to be scheduled tasklet. This avoids console freezing
when more data is to be transmitted, if the serial communication is not
closed.
Fixes: 69646d7a3689 ("tty/serial: atmel: RS485 HD w/DMA: enable RX after TX is stopped") Signed-off-by: Razvan Stefanescu <razvan.stefanescu@microchip.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20190813074025.16218-1-razvan.stefanescu@microchip.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The sequence of arguments which was passed to handle_lsr_errors() didn't
match the parameters defined in that function, &lsr was passed to flag
and &flag was passed to lsr, this patch fixed that.
The VPD implementation from Chromium Vital Product Data project used to
parse data from untrusted input without checking if the meta data is
invalid or corrupted. For example, the size from decoded content may
be negative value, or larger than whole input buffer. Such invalid data
may cause buffer overflow.
To fix that, the size parameters passed to vpd_decode functions should
be changed to unsigned integer (u32) type, and the parsing of entry
header should be refactored so every size field is correctly verified
before starting to decode.
Fixes: ad2ac9d5c5e0 ("firmware: Google VPD: import lib_vpd source files") Signed-off-by: Hung-Te Lin <hungte@chromium.org> Cc: stable <stable@vger.kernel.org> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/20190830022402.214442-1-hungte@chromium.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The first/last indexes are typically shared with a user app.
The app can change the 'last' index that the kernel uses
to store the next result. This change sanity checks the index
before using it for writing to a potentially arbitrary address.
This fixes CVE-2019-14821.
Cc: stable@vger.kernel.org Fixes: 5f94c1741bdc ("KVM: Add coalesced MMIO support (common part)") Signed-off-by: Matt Delco <delco@chromium.org> Signed-off-by: Jim Mattson <jmattson@google.com> Reported-by: syzbot+983c866c3dd6efa3662a@syzkaller.appspotmail.com
[Use READ_ONCE. - Paolo] Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When skb_shinfo(skb) is not able to cache extra fragment (that is,
skb_shinfo(skb)->nr_frags >= MAX_SKB_FRAGS), xennet_fill_frags() assumes
the sk_buff_head list is already empty. As a result, cons is increased only
by 1 and returns to error handling path in xennet_poll().
However, if the sk_buff_head list is not empty, queue->rx.rsp_cons may be
set incorrectly. That is, queue->rx.rsp_cons would point to the rx ring
buffer entries whose queue->rx_skbs[i] and queue->grant_rx_ref[i] are
already cleared to NULL. This leads to NULL pointer access in the next
iteration to process rx ring buffer entries.
Below is how xennet_poll() does error handling. All remaining entries in
tmpq are accounted to queue->rx.rsp_cons without assuming how many
outstanding skbs are remained in the list.
985 static int xennet_poll(struct napi_struct *napi, int budget)
... ...
1032 if (unlikely(xennet_set_skb_gso(skb, gso))) {
1033 __skb_queue_head(&tmpq, skb);
1034 queue->rx.rsp_cons += skb_queue_len(&tmpq);
1035 goto err;
1036 }
It is better to always have the error handling in the same way.
Fixes: ad4f15dc2c70 ("xen/netfront: don't bug in case of too many frags") Signed-off-by: Dongli Zhang <dongli.zhang@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The hardware manual should be revised, but the initial value of
VBCTRL.OCCLREN is set to 1 actually. If the bit is set, the hardware
clears VBCTRL.VBOUT and ADPCTRL.DRVVBUS registers automatically
when the hardware detects over-current signal from a USB power switch.
However, since the hardware doesn't have any registers which
indicates over-current, the driver cannot handle it at all. So, if
"is_otg_channel" hardware detects over-current, since ADPCTRL.DRVVBUS
register is cleared automatically, the channel cannot be used after
that.
To resolve this behavior, this patch sets the VBCTRL.OCCLREN to 0
to keep ADPCTRL.DRVVBUS even if the "is_otg_channel" hardware
detects over-current. (We assume a USB power switch itself protects
over-current and turns the VBUS off.)
This patch is inspired by a BSP patch from Kazuya Mizuguchi.
Fixes: 1114e2d31731 ("phy: rcar-gen3-usb2: change the mode to OTG on the combined channel") Cc: <stable@vger.kernel.org> # v4.5+ Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The error occurs when the descriptors_changed() routine (called during
a device reset) attempts to compare the old and new BOS and capability
descriptors. The length it uses for the comparison is the
wTotalLength value stored in BOS descriptor, but this value is not
necessarily the same as the length actually allocated for the
descriptors. If it is larger the routine will call memcmp() with a
length that is too big, thus reading beyond the end of the allocated
region and leading to this fault.
The kernel reads the BOS descriptor twice: first to get the total
length of all the capability descriptors, and second to read it along
with all those other descriptors. A malicious (or very faulty) device
may send different values for the BOS descriptor fields each time.
The memory area will be allocated using the wTotalLength value read
the first time, but stored within it will be the value read the second
time.
To prevent this possibility from causing any errors, this patch
modifies the BOS descriptor after it has been read the second time:
It sets the wTotalLength field to the actual length of the descriptors
that were read in and validated. Then the memcpy() call, or any other
code using these descriptors, will be able to rely on wTotalLength
being valid.
We use mmu_vmemmap_psize to find the page size for mapping the vmmemap area.
With radix translation, we are suboptimally setting this value to PAGE_SIZE.
We do check for 2M page size support and update mmu_vmemap_psize to use
hugepage size but we suboptimally reset the value to PAGE_SIZE in
radix__early_init_mmu(). This resulted in always mapping vmemmap area with
64K page size.
Fixes: 2bfd65e45e87 ("powerpc/mm/radix: Add radix callbacks for early init routines") Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In the generic code path, HID_DG_CONTACTMAX was previously
only read from the second byte of report 0x23.
Another report (0x82) has the HID_DG_CONTACTMAX in the
higher nibble of the third byte. We should support reading the
value of HID_DG_CONTACTMAX no matter what report we are reading
or which position that value is in.
To do this we submit the feature report as a event report
using hid_report_raw_event(). Our modified finger event path
records the value of HID_DG_CONTACTMAX when it sees that usage.
Fixes: 8ffffd5212846 ("HID: wacom: fix timeout on probe for some wacoms") Signed-off-by: Aaron Armstrong Skomra <aaron.skomra@wacom.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The last change to this Makefile caused relocation errors when loading
a kdump kernel. Restore -mcmodel=large (not -mcmodel=kernel),
-ffreestanding, and -fno-zero-initialized-bsss, without reverting to
the former practice of resetting KBUILD_CFLAGS.
Purgatory.ro is a standalone binary that is not linked against the
rest of the kernel. Its image is copied into an array that is linked
to the kernel, and from there kexec relocates it wherever it desires.
With the previous change to compiler flags, the error "kexec: Overflow
in relocation type 11 value 0x11fffd000" was encountered when trying
to load the crash kernel. This is from kexec code trying to relocate
the purgatory.ro object.
From the error message, relocation type 11 is R_X86_64_32S. The
x86_64 ABI says:
"The R_X86_64_32 and R_X86_64_32S relocations truncate the
computed value to 32-bits. The linker must verify that the
generated value for the R_X86_64_32 (R_X86_64_32S) relocation
zero-extends (sign-extends) to the original 64-bit value."
This type of relocation doesn't work when kexec chooses to place the
purgatory binary in memory that is not reachable with 32 bit
addresses.
The compiler flag -mcmodel=kernel allows those type of relocations to
be emitted, so revert to using -mcmodel=large as was done before.
Also restore the -ffreestanding and -fno-zero-initialized-bss flags
because they are appropriate for a stand alone piece of object code
which doesn't explicitly zero the bss, and one other report has said
undefined symbols are encountered without -ffreestanding.
These identical compiler flag changes need to happen for every object
that becomes part of the purgatory.ro object, so gather them together
first into PURGATORY_CFLAGS_REMOVE and PURGATORY_CFLAGS, and then
apply them to each of the objects that have C source. Do not apply
any of these flags to kexec-purgatory.o, which is not part of the
standalone object but part of the kernel proper.
Tested-by: Vaibhav Rustagi <vaibhavrustagi@google.com> Tested-by: Andreas Smas <andreas@lonelycoder.com> Signed-off-by: Steve Wahl <steve.wahl@hpe.com> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Cc: Borislav Petkov <bp@alien8.de> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: None Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: clang-built-linux@googlegroups.com Cc: dimitri.sivanich@hpe.com Cc: mike.travis@hpe.com Cc: russ.anderson@hpe.com Fixes: b059f801a937 ("x86/purgatory: Use CFLAGS_REMOVE rather than reset KBUILD_CFLAGS") Link: https://lkml.kernel.org/r/20190905202346.GA26595@swahl-linux Signed-off-by: Ingo Molnar <mingo@kernel.org> Cc: Andreas Smas <andreas@lonelycoder.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
There were a couple cases where the ITR value generated via the adaptive
ITR scheme could exceed 126. This resulted in the value becoming either 0
or something less than 10. Switching back and forth between a value less
than 10 and a value greater than 10 can cause issues as certain hardware
features such as RSC to not function well when the ITR value has dropped
that low.
CC: stable@vger.kernel.org Fixes: b4ded8327fea ("ixgbe: Update adaptive ITR algorithm") Reported-by: Gregg Leventhal <gleventhal@janestreet.com> Signed-off-by: Alexander Duyck <alexander.h.duyck@linux.intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
One of the very few warnings I have in the current build comes from
arch/x86/boot/edd.c, where I get the following with a gcc9 build:
arch/x86/boot/edd.c: In function ‘query_edd’:
arch/x86/boot/edd.c:148:11: warning: taking address of packed member of ‘struct boot_params’ may result in an unaligned pointer value [-Waddress-of-packed-member]
148 | mbrptr = boot_params.edd_mbr_sig_buffer;
| ^~~~~~~~~~~
This warning triggers because we throw away all the CFLAGS and then make
a new set for REALMODE_CFLAGS, so the -Wno-address-of-packed-member we
added in the following commit is not present:
The simplest solution for now is to adjust the warning for this version
of CFLAGS as well, but it would definitely make sense to examine whether
REALMODE_CFLAGS could be derived from CFLAGS, so that it picks up changes
in the compiler flags environment automatically.
The compatibility "eeprom" attribute is currently root-only no
matter what the configuration says. The "nvmem" attribute does
respect the setting of the root_only configuration bit, so do the
same for "eeprom".
Signed-off-by: Jean Delvare <jdelvare@suse.de> Fixes: b6c217ab9be6 ("nvmem: Add backwards compatibility support for older EEPROM drivers.") Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Cc: Arnd Bergmann <arnd@arndb.de> Link: https://lore.kernel.org/r/20190728184255.563332e6@endymion Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The CB4063 board uses pmc_plt_clk* clocks for ethernet controllers. This
adds it to the critclk_systems DMI table so the clocks are marked as
CLK_CRITICAL and not turned off.
Fixes: 648e921888ad ("clk: x86: Stop marking clocks as CLK_IS_CRITICAL") Signed-off-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This commit has caused regressions in notebooks that support suspend
to idle such as the XPS 9360, XPS 9370 and XPS 9380.
These notebooks will wakeup from suspend to idle from an unsolicited
advertising packet from an unpaired BLE device.
In a bug report it was sugggested that this is caused by a generic
lack of LE privacy support. Revert this commit until that behavior
can be avoided by the kernel.
Each iteration of for_each_child_of_node puts the previous
node, but in the case of a goto from the middle of the loop, there is
no put, thus causing a memory leak. Hence add an of_node_put before the
goto in two places.
Issue found with Coccinelle.
Fixes: 119f5173628a (drm/mediatek: Add DRM Driver for Mediatek SoC MT8173) Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com> Signed-off-by: CK Hu <ck.hu@mediatek.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
TI-SCI firmware will only respond to messages when the
TI_SCI_FLAG_REQ_ACK_ON_PROCESSED flag is set. Most messages already do
this, set this for the ones that do not.
This will be enforced in future firmware that better match the TI-SCI
specifications, this patch will not break users of existing firmware.
Fixes: aa276781a64a ("firmware: Add basic support for TI System Control Interface (TI-SCI) protocol") Signed-off-by: Andrew F. Davis <afd@ti.com> Acked-by: Nishanth Menon <nm@ti.com> Tested-by: Alejandro Hernandez <ajhernandez@ti.com> Signed-off-by: Tero Kristo <t-kristo@ti.com> Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
For decrypt, req->cryptlen includes the size of the authentication
part while all functions of the driver expect cryptlen to be
the size of the encrypted data.
As it is not expected to change req->cryptlen, this patch
implements local calculation of cryptlen.