Intel IOMMU could be turned off with intel_iommu=off. If Intel
IOMMU is off, the intel_iommu struct will not be initialized.
When device drivers call intel_svm_bind_mm(), the NULL pointer
reference will happen there.
Add dmar_disabled check to avoid NULL pointer reference.
Cc: Ashok Raj <ashok.raj@intel.com> Cc: Jacob Pan <jacob.jun.pan@linux.intel.com> Reported-by: Dave Jiang <dave.jiang@intel.com> Fixes: 2f26e0a9c9860 ("iommu/vt-d: Add basic SVM PASID support") Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com> Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When a child event is allocated in the inherit_event() path, the VMA
based filter offsets are not copied from the parent, even though the
address space mapping of the new task remains the same, which leads to
no trace for the new task until exec.
Reported-by: Mansour Alharthi <malharthi9@gatech.edu> Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Tested-by: Mathieu Poirier <mathieu.poirier@linaro.org> Acked-by: Peter Zijlstra <peterz@infradead.org> Cc: Jiri Olsa <jolsa@redhat.com> Fixes: 375637bc5249 ("perf/core: Introduce address range filtering") Link: http://lkml.kernel.org/r/20190215115655.63469-2-alexander.shishkin@linux.intel.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When a DSA port is added to a bridge and brought up, the resulting STP
state programmed into the hardware depends on the order that these
operations are performed. However, the Linux bridge code believes that
the port is in disabled mode.
If the DSA port is first added to a bridge and then brought up, it will
be in blocking mode. If it is brought up and then added to the bridge,
it will be in disabled mode.
This difference is caused by DSA always setting the STP mode in
dsa_port_enable() whether or not this port is part of a bridge. Since
bridge always sets the STP state when the port is added, brought up or
taken down, it is unnecessary for us to manipulate the STP state.
Apparently, this code was copied from Rocker, and the very next day a
similar fix for Rocker was merged but was not propagated to DSA. See e47172ab7e41 ("rocker: put port in FORWADING state after leaving bridge")
Fixes: b73adef67765 ("net: dsa: integrate with SWITCHDEV for HW bridging") Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The NOUVEAU_GETPARAM_PCI_DEVICE case is missing a break statement and falls
through to the following NOUVEAU_GETPARAM_BUS_TYPE case and may end up
re-assigning the getparam->value to an undesired value. Fix this by adding
in the missing break.
Detected by CoverityScan, CID#1460507 ("Missing break in switch")
Fixes: 359088d5b8ec ("drm/nouveau: remove trivial cases of nvxx_device() usage") Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The CPU port is special and does not need to obey VLAN restrictions as
far as untagged traffic goes, also, having the CPU port be part of a
particular PVID is against the idea of keeping it tagged in all VLANs.
Fixes: ca8931948344 ("net: dsa: b53: Keep CPU port as tagged in all VLANs") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
VLAN filtering can be built into the kernel, and also dynamically turned
on/off through the bridge master device. Allow re-configuring the switch
appropriately to account for that by deciding whether VLAN table
(v_table) misses should lead to a drop or forward.
Fixes: a2482d2ce349 ("net: dsa: b53: Plug in VLAN support") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
We were not consistent in how the default VID of a given port was
defined, b53_br_leave() would make sure the VLAN ID would be either 0/1
depending on the switch generation, but b53_configure_vlan(), which is
the default configuration would unconditionally set it to 1. The correct
value is 1 for 5325/5365 series and 0 otherwise. To avoid repeating that
mistake ever again, introduce a helper function: b53_default_pvid() to
factor that out.
Fixes: 967dd82ffc52 ("net: dsa: b53: Add support for Broadcom RoboSwitch") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The NAND controller device node was inserted into the wrong position,
probably due to a rebase or merge, as the file's structure does not
provide enough context for git to accurately match the previous device
node block.
The current code returns the number of all queues that can be used and
the number of queues that have been allocated, which is incorrect.
What should be returned is the number of queues allocated for each enabled
TC and the number of queues that can be allocated.
This patch fixes it.
Fixes: 849e46077689 ("net: hns3: add ethtool_ops.get_channels support for VF") Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The current code returns the number of all queues that can be used and
the number of queues that have been allocated, which is incorrect.
What should be returned is the number of queues allocated for each enabled
TC and the number of queues that can be allocated.
This patch fixes it.
Fixes: 482d2e9c1cc7 ("net: hns3: add support to query tqps number") Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Commit 5eed6f1dff87 ("fork,memcg: fix crash in free_thread_stack on
memcg charge fail") fixes a crash caused due to failed memcg charge of
the kernel stack. However the fix misses the cached_stacks case which
this patch fixes. So, the same crash can happen if the memcg charge of
a cached stack is failed.
Link: http://lkml.kernel.org/r/20190102180145.57406-1-shakeelb@google.com Fixes: 5eed6f1dff87 ("fork,memcg: fix crash in free_thread_stack on memcg charge fail") Signed-off-by: Shakeel Butt <shakeelb@google.com> Acked-by: Michal Hocko <mhocko@suse.com> Acked-by: Rik van Riel <riel@surriel.com> Cc: Rik van Riel <riel@surriel.com> Cc: Roman Gushchin <guro@fb.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Tejun Heo <tj@kernel.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The ->nr_signal is the supposed to be the number of elements in the
->signal array. There was one place where it was 5 but it was supposed
to be 4. That looks like a copy and paste bug. There were also two
checks that were off by one.
Fixes: 9e2c2e273012 ("drm/etnaviv: add infrastructure to query perf counter") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com> Tested-by: Christian Gmeiner <christian.gmeiner@gmail.com> Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Proxy vote for QDSS clock and remove vote on handover interrupt
to provide MSS PBL with access to STM hardware registers during
boot. Add "snoc_axi" and "mnoc_axi" to the active clock list.
Rename "gpll0_mss_clk" to "gpll0_mss" for consistency across SoCs.
Fixes: 9f058fa2efb1 ("remoteproc: qcom: Add support for mss remoteproc on msm8996") Signed-off-by: Sibi Sankar <sibis@codeaurora.org> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The bcm2835-thermal driver was added with commit ac178e4280e6
("ARM64: bcm2835: add thermal driver to default config"). Unfortunately
this was accidentally dropped by commit eb1e6716cc9c
("arm64: defconfig: sync with savedefconfig"). So enable the driver again.
Fixes: eb1e6716cc9c ("arm64: defconfig: sync with savedefconfig") Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Commit 9b6f7e163cd0 ("mm: rework memcg kernel stack accounting") will
result in fork failing if allocating a kernel stack for a task in
dup_task_struct exceeds the kernel memory allowance for that cgroup.
Unfortunately, it also results in a crash.
This is due to the code jumping to free_stack and calling
free_thread_stack when the memcg kernel stack charge fails, but without
tsk->stack pointing at the freshly allocated stack.
This in turn results in the vfree_atomic in free_thread_stack oopsing
with a backtrace like this:
In order to make the module bcm2835-camera load automatically, we need to
add a module alias.
Fixes: 4bebb0312ea9 ("staging/bcm2835-camera: Set ourselves up as a platform driver.") Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de> Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
There is one case where we may end up with no "supply" directory for the
OPPs in debugfs. That happens when the OPP core isn't managing the
regulators for the device and the device's OPP do have microvolt
property. It happens because the opp_table->regulator_count remains set
to 0 and the debugfs routines don't add any supply directory in such a
case.
This commit fixes that by setting opp_table->regulator_count to 1 in
that particular case. But to make everything work nicely and not break
other parts of the core, regulator_count is defined as "int" now instead
of "unsigned int" and it can have different special values now. It is
set to -1 initially to mark it "uninitialized" and later only we set it
to 0 or positive values after checking how many supplies are there.
This also helps in finding the bugs where only few of the OPPs have the
"opp-microvolt" property set and not all.
A CA is supposed to ignore FECN bits in multicast, ACK, and CNP
packets. This patch corrects the behavior of the HFI1 driver in this
regard by ignoring FECNs in those packet types.
While fixing the above behavior, fix the extraction of the FECN and BECN
bits from the packet headers for both 9B and 16B packets.
Furthermore, this patch corrects the driver's response to a FECN in RDMA
READ RESPONSE packets. Instead of sending an "empty" ACK, the driver now
sends a CNP packet. While editing that code path, add the missing trace
for CNP packets.
Fixes: 88733e3b8450 ("IB/hfi1: Add 16B UD support") Fixes: f59fb9e05109 ("IB/hfi1: Fix handling of FECN marked multicast packet") Reviewed-by: Kaike Wan <kaike.wan@intel.com> Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Mitko Haralanov <mitko.haralanov@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The GPIOX tsin_a pins wrongly uses the SDCard pinctrl bits, this
patch completely removes these pins entries until we find out what
are the correct bits and registers to be used instead.
An MC-aware mode was introduced in commit 7b8195306694 ("mlxsw:
spectrum: Configure MC-aware mode on mlxsw ports"). In MC-aware mode,
BUM traffic gets a special treatment by being assigned to a separate set
of traffic classes 8..15. Pairs of TCs 0 and 8, 1 and 9, etc., are then
configured to strictly prioritize the lower-numbered ones. The intention
is to prevent BUM traffic from flooding the switch and push out all UC
traffic, which would otherwise happen, and instead give UC traffic
precedence.
However strictly prioritizing UC traffic has the effect that UC overload
pushes out all BUM traffic, such as legitimate ARP queries. These
packets are kept in queues for a while, but under sustained UC overload,
their lifetime eventually expires and these packets are dropped. That is
detrimental to network performance as well.
Therefore configure the MC TCs (8..15) with minimum shaper of 200Mbps (a
minimum permitted value) to allow a trickle of necessary control traffic
to get through.
Fixes: 7b8195306694 ("mlxsw: spectrum: Configure MC-aware mode on mlxsw ports") Signed-off-by: Petr Machata <petrm@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
There is a compatibility issue between RTL8211E implemented
in Developerbox and netsec ethernet controller IP.
Our MDIO controller stops MDC clock right after the write
access, but RTL8211E expects MDC clock must be kept toggling
for several clock cycle with MDIO high before entering
the IDLE state. Without keeping clock after write access,
write access is not correctly handled and register is not
updated.
To meet this requirement, netsec driver needs to issue dummy
read(e.g. read PHYID1(offset 0x2) register) right after write
access, to keep MDC clock.
We think this compatibility issue is a problem specific to
our MDIO controller and RTL8211E.
Fixes: 533dd11a12f6 ("net: socionext: Add Synquacer NetSec driver") Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org> Signed-off-by: Yoshitoyo Osaki <osaki.yoshitoyo@socionext.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Since my change to split out the regulatory init to occur later,
any issues during earlier cfg80211_init() or errors during the
platform device allocation would lead to crashes later. Make this
more robust by checking that the earlier initialization succeeded.
The allocation with fsl_alloc_request() and kmalloc() were unchecked
fixed this up with a NULL check and appropriate cleanup.
Additionally udc->ep_qh_size was reset to 0 on failure of allocation.
Similar udc->phy_mode is initially 0 (as udc_controller was
allocated with kzalloc in fsl_udc_probe()) so reset it to 0 as well
so that this function is side-effect free on failure. Not clear if
this is necessary or sensible as fsl_udc_release() probably can not
be called if fsl_udc_probe() failed - but it should not hurt.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org> Fixes: b504882da5 ("USB: add Freescale high-speed USB SOC device controller driver") Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
On a DT based system, we use the of_node full name to name the
corresponding irq domain. We expect that name to be unique, so so that
domains with the same base name won't clash (this happens on multi-node
topologies, for example).
Since a7e4cfb0a7ca ("of/fdt: only store the device node basename in
full_name"), of_node_full_name() lies and only returns the basename. This
breaks the above requirement, and we end-up with only a subset of the
domains in /sys/kernel/debug/irq/domains.
Let's reinstate the feature by using the fancy new %pOF format specifier,
which happens to do the right thing.
Fixes: a7e4cfb0a7ca ("of/fdt: only store the device node basename in full_name") Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lkml.kernel.org/r/20181001100522.180054-3-marc.zyngier@arm.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The ia64 handling of failure to setup a signal frame has been trying
to set overlapping fields in struct siginfo since 2.3.43. The si_pid
and si_uid fields are stomped when the si_addr field is set. The
si_code of SI_KERNEL indicates that si_pid and si_uid should be valid,
and that si_addr does not exist.
Being at odds with the definition of SI_KERNEL and with nothing to
indicate that this was a signal frame setup failure there is no way
for userspace to know that si_addr was filled out instead.
In practice failure to setup a signal frame is rare, and si_pid and
si_uid are always set to 0 when si_code is SI_KERNEL so I expect no
one has looked closely enough before to see this weirdness. Further
the only difference between force_sigsegv_info and the generic
force_sigsegv other than the return code is that force_sigsegv_info
stomps the si_uid and si_pid fields.
Remove the bug and simplify the code by using force_sigsegv in this
case just like other architectures.
Fixes: 2.3.43 Cc: Tony Luck <tony.luck@intel.com> Cc: Fenghua Yu <fenghua.yu@intel.com> Cc: linux-ia64@vger.kernel.org Acked-by: Tony Luck <tony.luck@intel.com> Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Now that the /firmware/coreboot node in DT is populated by the core DT
platform code with commit 3aa0582fdb82 ("of: platform: populate
/firmware/ node from of_platform_default_populate_init()") we should and
can remove the platform device creation here. Otherwise, the
of_platform_device_create() call will fail, the coreboot of driver won't
be registered, and this driver will never bind. At the same time, we
should move this driver to use MODULE_DEVICE_TABLE so that module
auto-load works properly when the coreboot device is auto-populated and
we should drop the of_node handling that was presumably placed here to
hold a reference to the DT node created during module init that no
longer happens.
Cc: Wei-Ning Huang <wnhuang@chromium.org> Cc: Julius Werner <jwerner@chromium.org> Reviewed-by: Brian Norris <briannorris@chromium.org> Cc: Samuel Holland <samuel@sholland.org> Reviewed-by: Sudeep Holla <Sudeep.Holla@arm.com> Fixes: 3aa0582fdb82 ("of: platform: populate /firmware/ node from of_platform_default_populate_init()") Signed-off-by: Stephen Boyd <swboyd@chromium.org> Reviewed-by: Julius Werner <jwerner@chromium.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Signed-off-by: Tony Jones <tonyj@suse.de> Fixes: 56974a6fcfef ("apparmor: add base infastructure for socket
mediation") Signed-off-by: John Johansen <john.johansen@canonical.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
At some point in the past we needed to make sure we would get the long
name of modules and not just what we get from /proc/modules, but that
need, as described in the cset that introduced the adjustment function:
Fixes: c03d5184f0e9 ("perf machine: Adjust dso->long_name for offline module")
Without using the buildid-cache:
# lsmod | grep trusted
# insmod trusted.ko
# lsmod | grep trusted
trusted 24576 0
# strace -e open,openat perf probe -m ./trusted.ko key_seal |& grep trusted
openat(AT_FDCWD, "/sys/module/trusted/notes/.note.gnu.build-id", O_RDONLY) = 4
openat(AT_FDCWD, "/sys/module/trusted/notes/.note.gnu.build-id", O_RDONLY) = 7
openat(AT_FDCWD, "/root/trusted.ko", O_RDONLY) = 3
openat(AT_FDCWD, "/root/.debug/root/trusted.ko/dd3d355d567394d540f527e093e0f64b95879584/probes", O_RDWR|O_CREAT, 0644) = 3
openat(AT_FDCWD, "/usr/lib/debug/root/trusted.ko.debug", O_RDONLY) = -1 ENOENT (No such file or directory)
openat(AT_FDCWD, "/usr/lib/debug/root/trusted.ko", O_RDONLY) = -1 ENOENT (No such file or directory)
openat(AT_FDCWD, "/root/.debug/trusted.ko", O_RDONLY) = -1 ENOENT (No such file or directory)
openat(AT_FDCWD, "/root/trusted.ko", O_RDONLY) = 3
openat(AT_FDCWD, "trusted.ko.debug", O_RDONLY) = -1 ENOENT (No such file or directory)
openat(AT_FDCWD, ".debug/trusted.ko.debug", O_RDONLY) = -1 ENOENT (No such file or directory)
openat(AT_FDCWD, "trusted.ko.debug", O_RDONLY) = -1 ENOENT (No such file or directory)
openat(AT_FDCWD, "/root/trusted.ko", O_RDONLY) = 3
openat(AT_FDCWD, "/root/trusted.ko", O_RDONLY) = 3
openat(AT_FDCWD, "/root/trusted.ko", O_RDONLY) = 4
openat(AT_FDCWD, "/root/trusted.ko", O_RDONLY) = 3
probe:key_seal (on key_seal in trusted)
# perf probe -l
probe:key_seal (on key_seal in trusted)
#
No attempt at opening '[trusted]'.
Now using the build-id cache:
# rmmod trusted
# perf buildid-cache --add ./trusted.ko
# insmod trusted.ko
# strace -e open,openat perf probe -m ./trusted.ko key_seal |& grep trusted
openat(AT_FDCWD, "/sys/module/trusted/notes/.note.gnu.build-id", O_RDONLY) = 4
openat(AT_FDCWD, "/sys/module/trusted/notes/.note.gnu.build-id", O_RDONLY) = 7
openat(AT_FDCWD, "/root/trusted.ko", O_RDONLY) = 3
openat(AT_FDCWD, "/root/.debug/root/trusted.ko/dd3d355d567394d540f527e093e0f64b95879584/probes", O_RDWR|O_CREAT, 0644) = 3
openat(AT_FDCWD, "/usr/lib/debug/root/trusted.ko.debug", O_RDONLY) = -1 ENOENT (No such file or directory)
openat(AT_FDCWD, "/usr/lib/debug/root/trusted.ko", O_RDONLY) = -1 ENOENT (No such file or directory)
openat(AT_FDCWD, "/root/.debug/trusted.ko", O_RDONLY) = -1 ENOENT (No such file or directory)
openat(AT_FDCWD, "/root/trusted.ko", O_RDONLY) = 3
openat(AT_FDCWD, "trusted.ko.debug", O_RDONLY) = -1 ENOENT (No such file or directory)
openat(AT_FDCWD, ".debug/trusted.ko.debug", O_RDONLY) = -1 ENOENT (No such file or directory)
openat(AT_FDCWD, "trusted.ko.debug", O_RDONLY) = -1 ENOENT (No such file or directory)
openat(AT_FDCWD, "/root/trusted.ko", O_RDONLY) = 3
openat(AT_FDCWD, "/root/trusted.ko", O_RDONLY) = 3
openat(AT_FDCWD, "/root/trusted.ko", O_RDONLY) = 4
openat(AT_FDCWD, "/root/trusted.ko", O_RDONLY) = 3
#
Again, no attempt at reading '[trusted]'.
Finally, adding a probe to that function and then using:
This was the only path I could find using the perf tools that reach at this
function, then as of november/2019, if we put a probe in the line where the
actuall setting of the dso->long_name is done:
To further test this I used kvm.ko as the offline module, i.e. removed
if from the buildid-cache by nuking it completely (rm -rf ~/.debug) and
moved it from the normal kernel distro path, removed the modules, stoped
the kvm guest, and then installed it manually, etc.
# rmmod kvm-intel
# rmmod kvm
# lsmod | grep kvm
# modprobe kvm-intel
modprobe: ERROR: ctx=0x55d3b1722260 path=/lib/modules/5.3.8-200.fc30.x86_64/kernel/arch/x86/kvm/kvm.ko.xz error=No such file or directory
modprobe: ERROR: ctx=0x55d3b1722260 path=/lib/modules/5.3.8-200.fc30.x86_64/kernel/arch/x86/kvm/kvm.ko.xz error=No such file or directory
modprobe: ERROR: could not insert 'kvm_intel': Unknown symbol in module, or unknown parameter (see dmesg)
# insmod ./kvm.ko
# modprobe kvm-intel
modprobe: ERROR: ctx=0x562f34026260 path=/lib/modules/5.3.8-200.fc30.x86_64/kernel/arch/x86/kvm/kvm.ko.xz error=No such file or directory
modprobe: ERROR: ctx=0x562f34026260 path=/lib/modules/5.3.8-200.fc30.x86_64/kernel/arch/x86/kvm/kvm.ko.xz error=No such file or directory
# lsmod | grep kvm
kvm_intel 299008 0
kvm 765952 1 kvm_intel
irqbypass 16384 1 kvm
#
# perf probe -x ~/bin/perf machine__findnew_module_map:12 mname=m.name:string filename=filename:string 'dso_long_name=map->dso->long_name:string' 'dso_name=map->dso->name:string'
# perf probe -l
probe_perf:machine__findnew_module_map (on machine__findnew_module_map:12@util/machine.c in /home/acme/bin/perf with mname filename dso_long_name dso_name)
# perf record
^C[ perf record: Woken up 2 times to write data ]
[ perf record: Captured and wrote 3.416 MB perf.data (33956 samples) ]
# perf trace -e probe_perf:machine*
<SNIP>
6.322 perf/23099 probe_perf:machine__findnew_module_map(__probe_ip: 5492493, mname: "[salsa20_generic]", filename: "/lib/modules/5.3.8-200.fc30.x86_64/kernel/crypto/salsa20_generic.ko.xz", dso_long_name: "/lib/modules/5.3.8-200.fc30.x86_64/kernel/crypto/salsa20_generic.ko.xz", dso_name: "[salsa20_generic]")
6.375 perf/23099 probe_perf:machine__findnew_module_map(__probe_ip: 5492493, mname: "[kvm]", filename: "[kvm]", dso_long_name: "[kvm]", dso_name: "[kvm]")
<SNIP>
The filename doesn't come with the path, no point in trying to set the dso->long_name.
[root@quaco ~]# strace -e open,openat perf probe -m ./kvm.ko kvm_apic_local_deliver |& egrep 'open.*kvm'
openat(AT_FDCWD, "/sys/module/kvm_intel/notes/.note.gnu.build-id", O_RDONLY) = 4
openat(AT_FDCWD, "/sys/module/kvm/notes/.note.gnu.build-id", O_RDONLY) = 4
openat(AT_FDCWD, "/lib/modules/5.3.8-200.fc30.x86_64/kernel/arch/x86/kvm", O_RDONLY|O_NONBLOCK|O_CLOEXEC|O_DIRECTORY) = 7
openat(AT_FDCWD, "/sys/module/kvm_intel/notes/.note.gnu.build-id", O_RDONLY) = 8
openat(AT_FDCWD, "/root/kvm.ko", O_RDONLY) = 3
openat(AT_FDCWD, "/root/.debug/root/kvm.ko/5955f426cb93f03f30f3e876814be2db80ab0b55/probes", O_RDWR|O_CREAT, 0644) = 3
openat(AT_FDCWD, "/usr/lib/debug/root/kvm.ko.debug", O_RDONLY) = -1 ENOENT (No such file or directory)
openat(AT_FDCWD, "/usr/lib/debug/root/kvm.ko", O_RDONLY) = -1 ENOENT (No such file or directory)
openat(AT_FDCWD, "/root/.debug/kvm.ko", O_RDONLY) = -1 ENOENT (No such file or directory)
openat(AT_FDCWD, "/root/kvm.ko", O_RDONLY) = 3
openat(AT_FDCWD, "kvm.ko.debug", O_RDONLY) = -1 ENOENT (No such file or directory)
openat(AT_FDCWD, ".debug/kvm.ko.debug", O_RDONLY) = -1 ENOENT (No such file or directory)
openat(AT_FDCWD, "kvm.ko.debug", O_RDONLY) = -1 ENOENT (No such file or directory)
openat(AT_FDCWD, "/root/kvm.ko", O_RDONLY) = 3
openat(AT_FDCWD, "/root/kvm.ko", O_RDONLY) = 3
openat(AT_FDCWD, "/root/kvm.ko", O_RDONLY) = 4
openat(AT_FDCWD, "/root/kvm.ko", O_RDONLY) = 3
[root@quaco ~]#
Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Wang Nan <wangnan0@huawei.com> Link: https://lkml.kernel.org/n/tip-jlfew3lyb24d58egrp0o72o2@git.kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
gss_read_proxy_verf() assumes things about the XDR buffer containing
the RPC Call that are not true for buffers generated by
svc_rdma_recv().
RDMA's buffers look more like what the upper layer generates for
sending: head is a kmalloc'd buffer; it does not point to a page
whose contents are contiguous with the first page in the buffers'
page array. The result is that ACCEPT_SEC_CONTEXT via RPC/RDMA has
stopped working on Linux NFS servers that use gssproxy.
This does not affect clients that use only TCP to send their
ACCEPT_SEC_CONTEXT operation (that's all Linux clients). Other
clients, like Solaris NFS clients, send ACCEPT_SEC_CONTEXT on the
same transport as they send all other NFS operations. Such clients
can send ACCEPT_SEC_CONTEXT via RPC/RDMA.
I thought I had found every direct reference in the server RPC code
to the rqstp->rq_pages field.
Bug found at the 2019 Westford NFS bake-a-thon.
Fixes: 3316f0631139 ("svcrdma: Persistently allocate and DMA- ... ") Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Tested-by: Bill Baker <bill.baker@oracle.com> Reviewed-by: Simo Sorce <simo@redhat.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Some platforms execute their timer handler with the interrupt priority
level set below 6. That means the handler could be interrupted by another
driver and this could lead to re-entry of the timer core.
Avoid this by use of local_irq_save/restore for timer interrupt dispatch.
This provides mutual exclusion around the timer interrupt flag access
which is needed later in this series for the clocksource conversion.
Reported-by: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/alpine.DEB.2.21.1811131407120.2697@nanos.tec.linutronix.de Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The interrupt clear flag register is a "write 1 to clear" register.
So, only writing ones allows to clear flags:
- Replace buggy stm32_clr_bits() by a simple write to clear error flags
- Replace useless read/modify/write stm32_set_bits() routine by a
simple write to clear TC (transfer complete) flag.
The retured value from ib_dma_map_sg saved in dma_nents variable. To avoid
future mismatch between types, define dma_nents as an integer instead of
unsigned.
Fixes: 57b26497fabe ("IB/iser: Pass the correct number of entries for dma mapped SGL") Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Israel Rukshin <israelr@mellanox.com> Signed-off-by: Max Gurtovoy <maxg@mellanox.com> Acked-by: Sagi Grimberg <sagi@grimberg.me> Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Older versions of the Juno *SoC* TRM [1] recommended that the UART clock
source should be 7.2738 MHz, whereas the *system* TRM [2] stated a more
correct value of 7.3728 MHz. Somehow the wrong value managed to end up in
our DT.
Doing a prime factorisation, a modulo divide by 115200 and trying
to buy a 7.2738 MHz crystal at your favourite electronics dealer suggest
that the old value was actually a typo. The actual UART clock is driven
by a PLL, configured via a parameter in some board.txt file in the
firmware, which reads 7.37 MHz (sic!).
Fix this to correct the baud rate divisor calculation on the Juno board.
The INTERRUPT_CNTL2 register expects a valid DMA address, but is
currently set with a GPU MC address. This can cause problems on
systems that detect the resulting DMA read from an invalid address
(found on a Power8 guest).
Instead, use the DMA address of the dummy page because it will always
be safe.
Fixes: d8f60cfc9345 ("drm/radeon/kms: Add support for interrupts on r6xx/r7xx chips (v3)") Fixes: 25a857fbe973 ("drm/radeon/kms: add support for interrupts on SI") Fixes: a59781bbe528 ("drm/radeon: add support for interrupts on CIK (v5)") Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In affs_remount if data is provided it is duplicated into new_opts. The
allocated memory for new_opts is only released if parse_options fails.
There's a bit of history behind new_options, originally there was
save/replace options on the VFS layer so the 'data' passed must not
change (thus strdup), this got cleaned up in later patches. But not
completely.
There's no reason to do the strdup in cases where the filesystem does
not need to reuse the 'data' again, because strsep would modify it
directly.
v4.11-rc1 did introduce a patch series that rearranged the
sdio quirks into a header file. Unfortunately this did forget
to handle SDIO_VENDOR_ID_TI differently between wl1251 and
wl1271 with the result that although the wl1251 was found on
the sdio bus, the firmware did not load any more and there was
no interface registration.
This patch defines separate constants to be used by sdio quirks
and drivers.
Fixes: 884f38607897 ("mmc: core: move some sdio IDs out of quirks file") Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com> Cc: <stable@vger.kernel.org> # v4.11+ Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Adding a couple of READ_ONCE()/WRITE_ONCE() should silence it.
Since the report hinted about multiple cpus using the history
concurrently, I added a test avoiding writing on it if the
victim slot already contains the desired value.
[1]
BUG: KCSAN: data-race in fanout_demux_rollover / fanout_demux_rollover
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 18922 Comm: syz-executor.3 Not tainted 5.4.0-rc6+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Fixes: 3b3a5b0aab5b ("packet: rollover huge flows before small flows") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
A difference of two unsigned long needs long storage.
Fixes: c7fb64db001f ("[NETLINK]: Neighbour table configuration and statistics via rtnetlink") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When the driver needs to create a hash value because it
was not done at higher level, then the hash should be marked
as a software not hardware hash.
Fixes: f72860afa2e3 ("hv_netvsc: Exclude non-TCP port numbers from vRSS hashing") Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
By default s_maxbytes is set to MAX_NON_LFS, which limits the usable
file size to 2GB, enforced by the vfs.
Commit b9b1f8d5930a ("AFS: write support fixes") added support for the
64-bit fetch and store server operations, but did not change this value.
As a result, attempts to write past the 2G mark result in EFBIG errors:
$ dd if=/dev/zero of=foo bs=1M count=1 seek=2048
dd: error writing 'foo': File too large
Set s_maxbytes to MAX_LFS_FILESIZE.
Fixes: b9b1f8d5930a ("AFS: write support fixes") Signed-off-by: Marc Dionne <marc.dionne@auristor.com> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The reset counter is specific for every QCA700x chip. So move this
into the private driver struct. Otherwise we get unpredictable reset
behavior in setups with multiple QCA700x chips.
Fixes: 291ab06ecf67 (net: qualcomm: new Ethernet over SPI driver for QCA7000) Signed-off-by: Stefan Wahren <stefan.wahren@in-tech.com> Signed-off-by: Stefan Wahren <wahrenst@gmx.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If packet corruption failed we jump to finish_segs and return
NET_XMIT_SUCCESS. Seeing success will make the parent qdisc
increment its backlog, that's incorrect - we need to return
NET_XMIT_DROP.
Fixes: 6071bd1aa13e ("netem: Segment GSO packets on enqueue") Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
To corrupt a GSO frame we first perform segmentation. We then
proceed using the first segment instead of the full GSO skb and
requeue the rest of the segments as separate packets.
If there are any issues with processing the first segment we
still want to process the rest, therefore we jump to the
finish_segs label.
Commit 177b8007463c ("net: netem: fix backlog accounting for
corrupted GSO frames") started using the pointer to the first
segment in the "rest of segments processing", but as mentioned
above the first segment may had already been freed at this point.
Backlog corrections for parent qdiscs have to be adjusted.
Fixes: 177b8007463c ("net: netem: fix backlog accounting for corrupted GSO frames") Reported-by: kbuild test robot <lkp@intel.com> Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Reported-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Illegal memory will be touch if SDMA_SCRIPT_ADDRS_ARRAY_SIZE_V3
(41) exceed the size of structure sdma_script_start_addrs(40),
thus cause memory corrupt such as slob block header so that kernel
trap into while() loop forever in slob_free(). Please refer to below
code piece in imx-sdma.c:
for (i = 0; i < sdma->script_number; i++)
if (addr_arr[i] > 0)
saddr_arr[i] = addr_arr[i]; /* memory corrupt here */
That issue was brought by commit a572460be9cf ("dmaengine: imx-sdma: Add
support for version 3 firmware") because SDMA_SCRIPT_ADDRS_ARRAY_SIZE_V3
(38->41 3 scripts added) not align with script number added in
sdma_script_start_addrs(2 scripts).
Fixes: a572460be9cf ("dmaengine: imx-sdma: Add support for version 3 firmware") Cc: stable@vger.kernel Link: https://www.spinics.net/lists/arm-kernel/msg754895.html Signed-off-by: Robin Gong <yibin.gong@nxp.com> Reported-by: Jurgen Lambrecht <J.Lambrecht@TELEVIC.com> Link: https://lore.kernel.org/r/1569347584-3478-1-git-send-email-yibin.gong@nxp.com
[vkoul: update the patch title] Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
On msm8998, vblank timeouts are observed because the DSI controller is not
reset properly, which ends up stalling the MDP. This is because the reset
logic is not correct per the hardware documentation.
The documentation states that after asserting reset, software should wait
some time (no indication of how long), or poll the status register until it
returns 0 before deasserting reset.
wmb() is insufficient for this purpose since it just ensures ordering, not
timing between writes. Since asserting and deasserting reset occurs on the
same register, ordering is already guaranteed by the architecture, making
the wmb extraneous.
Since we would define a timeout for polling the status register to avoid a
possible infinite loop, lets just use a static delay of 20 ms, since 16.666
ms is the time available to process one frame at 60 fps.
Fixes: a689554ba6ed ("drm/msm: Initial add DSI connector support") Cc: Hai Li <hali@codeaurora.org> Cc: Rob Clark <robdclark@gmail.com> Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com> Reviewed-by: Sean Paul <sean@poorly.run>
[seanpaul renamed RESET_DELAY to DSI_RESET_TOGGLE_DELAY_MS] Signed-off-by: Sean Paul <seanpaul@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20191011133939.16551-1-jeffrey.l.hugo@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The field "name" in struct ptp_clock_info has a fixed size of 16
chars and is used as zero terminated string by clock_name_show()
in drivers/ptp/ptp_sysfs.c
The current initialization value requires 17 chars to fit also the
null termination, and this causes overflow to the next bytes in
the struct when the string is read as null terminated:
hexdump -C /sys/class/ptp/ptp0/clock_name 00000000 73 74 6d 6d 61 63 5f 70 74 70 5f 63 6c 6f 63 6b |stmmac_ptp_clock| 00000010 a0 ac b9 03 0a |.....|
where the extra 4 bytes (excluding the newline) after the string
represent the integer 0x03b9aca0 = 62500000 assigned to the field
"max_adj" that follows "name" in the same struct.
There is no strict requirement for the "name" content and in the
comment in ptp_clock_kernel.h it's reported it should just be 'A
short "friendly name" to identify the clock'.
Replace it with "stmmac ptp".
Signed-off-by: Antonio Borneo <antonio.borneo@st.com> Fixes: 92ba6888510c ("stmmac: add the support for PTP hw clock driver") Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If llc_conn_state_process() sees that llc_conn_service() put the skb on
a list, it will drop one fewer references to it. This is wrong because
the current behavior is that llc_conn_service() never consumes a
reference to the skb.
The code also makes the number of skb references being dropped
conditional on which of ind_prim and cfm_prim are nonzero, yet neither
of these affects how many references are *acquired*. So there is extra
code that tries to fix this up by sometimes taking another reference.
Remove the unnecessary/broken refcounting logic and instead just add an
skb_get() before the only two places where an extra reference is
actually consumed.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
All callers of llc_conn_state_process() except llc_build_and_send_pkt()
(via llc_ui_sendmsg() -> llc_ui_send_data()) assume that it always
consumes a reference to the skb. Fix this caller to do the same.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
We can process deauth frames and all, but we drop them very
early in the RX path today - this could never have worked.
Fixes: 2cc59e784b54 ("mac80211: reply to AUTH with DEAUTH if sta allocation fails in IBSS") Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Link: https://lore.kernel.org/r/20191004123706.15768-2-luca@coelho.fi Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
"nvme: add a common helper to read Identify Controller data"
has re-introduced an issue that we have attempted to work around in the
past, in commit a310acd7a7ea ("NVMe: use split lo_hi_{read,write}q").
The problem is that some PCIe NVMe controllers do not implement 64-bit
outbound accesses correctly, which is why the commit above switched
to using lo_hi_[read|write]q for all 64-bit BAR accesses occuring in
the code.
In the mean time, the NVMe subsystem has been refactored, and now calls
into the PCIe support layer for NVMe via a .reg_read64() method, which
fails to use lo_hi_readq(), and thus reintroduces the problem that the
workaround above aimed to address.
Given that, at the moment, .reg_read64() is only used to read the
capability register [which is known to tolerate split reads], let's
switch .reg_read64() to lo_hi_readq() as well.
This fixes a boot issue on some ARM boxes with NVMe behind a Synopsys
DesignWare PCIe host controller.
Fixes: 7fd8930f26be4 ("nvme: add a common helper to read Identify Controller data") Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The "iface" variable is an enum and in this context GCC treats it as
an unsigned int so the error handling is never triggered.
Fixes: b78624125304 ("of_mdio: Abstract a general interface for phy connect") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The "lp->phy_mode" is an enum but in this context GCC treats it as an
unsigned int so the error handling is never triggered.
Fixes: ee06b1728b95 ("net: axienet: add support for standard phy-mode binding") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The "dwmac->phy_mode" is an enum and in this context GCC treats it as
an unsigned int so the error handling is never triggered.
Fixes: 566e82516253 ("net: stmmac: add a glue driver for the Amlogic Meson 8b / GXBB DWMAC") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The "priv->phy_mode" variable is an enum and in this context GCC will
treat it as unsigned to the error handling will never trigger.
Fixes: 57c5bc9ad7d7 ("net: hisilicon: add hix5hd2 mac driver") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The irqreturn_t type is an enum or an unsigned int in GCC. That
creates to problems because it can't detect if the
self->aq_hw_ops->hw_irq_read() call fails and at the end the function
always returns IRQ_HANDLED.
drivers/net/ethernet/aquantia/atlantic/aq_vec.c:316 aq_vec_isr_legacy() warn: unsigned 'err' is never less than zero.
drivers/net/ethernet/aquantia/atlantic/aq_vec.c:329 aq_vec_isr_legacy() warn: always true condition '(err >= 0) => (0-u32max >= 0)'
Fixes: 970a2e9864b0 ("net: ethernet: aquantia: Vector operations") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Igor Russkikh <igor.russkikh@aquantia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In addr_handler(), assuming status == 0 and the device already has been
acquired (id_priv->cma_dev != NULL), we get the following incorrect
"error" message:
RDMA CM: ADDR_ERROR: failed to resolve IP. status 0
Fixes: 498683c6a7ee ("IB/cma: Add debug messages to error flows") Link: https://lore.kernel.org/r/20190902092731.1055757-1-haakon.bugge@oracle.com Signed-off-by: HÃ¥kon Bugge <haakon.bugge@oracle.com> Reviewed-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When the FW bundles multiple packets, pkt->act_len may be incorrect
as it refers to the first packet only (however, the FW will only
bundle packets that fit into the same pkt->alloc_len).
Before this patch, the skb length would be set (incorrectly) to
pkt->act_len in ath10k_sdio_mbox_rx_packet, and then later manually
adjusted in ath10k_sdio_mbox_rx_process_packet.
The first problem is that ath10k_sdio_mbox_rx_process_packet does not
use proper skb_put commands to adjust the length (it directly changes
skb->len), so we end up with a mismatch between skb->head + skb->tail
and skb->data + skb->len. This is quite serious, and causes corruptions
in the TCP stack, as the stack tries to coalesce packets, and relies
on skb->tail being correct (that is, skb_tail_pointer must point to
the first byte_after_ the data).
Instead of re-adjusting the size in ath10k_sdio_mbox_rx_process_packet,
this moves the code to ath10k_sdio_mbox_rx_packet, and also add a
bounds check, as skb_put would crash the kernel if not enough space is
available.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Fixes: 8530b4e7b22bc3b ("ath10k: sdio: set skb len for all rx packets") Signed-off-by: Nicolas Boichat <drinkcat@chromium.org> Signed-off-by: Wen Gong <wgong@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
sonic_send_packet will be processed in irq or non-irq
context, so it would better use dev_kfree_skb_any
instead of dev_kfree_skb.
Fixes: d9fb9f384292 ("*sonic/natsemi/ns83829: Move the National Semi-conductor drivers") Signed-off-by: Mao Wenan <maowenan@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Fix an error in the bitmaskfor the shtc1 and shtw1 bitmask used to
retrieve the chip ID from the ID register. See section 5.7 of the shtw1
or shtc1 datasheet for details.
Fixes: 1a539d372edd9832444e7a3daa710c444c014dc9 ("hwmon: add support for Sensirion SHTC1 sensor") Signed-off-by: Dan Robertson <dan@dlrobertson.com> Link: https://lore.kernel.org/r/20190905014554.21658-3-dan@dlrobertson.com
[groeck: Reordered to be first in series and adjusted accordingly] Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In Xen environment, if Xen-swiotlb is enabled, ixgbe driver
could possibly allocate a page, DMA memory buffer, for the first
fragment which is not suitable for Xen-swiotlb to do DMA operations.
Xen-swiotlb have to internally allocate another page for doing DMA
operations. This mechanism requires syncing the data from the internal
page to the page which ixgbe sends to upper network stack. However,
since commit f3213d932173 ("ixgbe: Update driver to make use of DMA
attributes in Rx path"), the unmap operation is performed with
DMA_ATTR_SKIP_CPU_SYNC. As a result, the sync is not performed.
Since the sync isn't performed, the upper network stack could receive
a incomplete network packet. By incomplete, it means the linear data
on the first fragment(between skb->head and skb->end) is invalid. So
we have to copy the data from the internal xen-swiotlb page to the page
which ixgbe sends to upper network stack through the sync operation.
More details from Alexander Duyck:
Specifically since we are mapping the frame with
DMA_ATTR_SKIP_CPU_SYNC we have to unmap with that as well. As a result
a sync is not performed on an unmap and must be done manually as we
skipped it for the first frag. As such we need to always sync before
possibly performing a page unmap operation.
Fixes: f3213d932173 ("ixgbe: Update driver to make use of DMA attributes in Rx path") Signed-off-by: Firo Yang <firo.yang@suse.com> Reviewed-by: Alexander Duyck <alexander.h.duyck@linux.intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
generic_write_checks() may modify iov_iter_count(), so we must get the
count after the call, not before. Using the wrong one has a couple of
consequences:
1. We check a longer range in check_can_nocow() for nowait than we're
actually writing.
2. We create extra hole extent maps in btrfs_cont_expand(). As far as I
can tell, this is harmless, but I might be missing something.
These issues are pretty minor, but let's fix it before something more
important trips on it.
Fixes: edf064e7c6fe ("btrfs: nowait aio support") Reviewed-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Omar Sandoval <osandov@fb.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If the caching thread fails to allocate a path, it returns without waking
up any cache waiters, leaving them hang forever. Fix this by following the
same approach as when we fail to start the caching thread: print an error
message, disable inode caching and make the wakers fallback to non-caching
mode behaviour (calling btrfs_find_free_objectid()).
Fixes: 581bb050941b4f ("Btrfs: Cache free inode numbers in memory") Reviewed-by: Nikolay Borisov <nborisov@suse.com> Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If we fail to start the inode caching thread, we print an error message
and disable the inode cache, however we never wake up any waiters, so they
hang forever waiting for the caching to finish. Fix this by waking them
up and have them fallback to a call to btrfs_find_free_objectid().
Fixes: e60efa84252c05 ("Btrfs: avoid triggering bug_on() when we fail to start inode caching task") Reviewed-by: Nikolay Borisov <nborisov@suse.com> Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If we are able to load an existing inode cache off disk, we set the state
of the cache to BTRFS_CACHE_FINISHED, but we don't wake up any one waiting
for the cache to be available. This means that anyone waiting for the
cache to be available, waiting on the condition that either its state is
BTRFS_CACHE_FINISHED or its available free space is greather than zero,
can hang forever.
This could be observed running fstests with MOUNT_OPTIONS="-o inode_cache",
in particular test case generic/161 triggered it very frequently for me,
producing a trace like the following:
[63795.739712] BTRFS info (device sdc): enabling inode map caching
[63795.739714] BTRFS info (device sdc): disk space caching is enabled
[63795.739716] BTRFS info (device sdc): has skinny extents
[64036.653886] INFO: task btrfs-transacti:3917 blocked for more than 120 seconds.
[64036.654079] Not tainted 5.2.0-rc4-btrfs-next-50 #1
[64036.654143] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[64036.654232] btrfs-transacti D 0 3917 2 0x80004000
[64036.654239] Call Trace:
[64036.654258] ? __schedule+0x3ae/0x7b0
[64036.654271] schedule+0x3a/0xb0
[64036.654325] btrfs_commit_transaction+0x978/0xae0 [btrfs]
[64036.654339] ? remove_wait_queue+0x60/0x60
[64036.654395] transaction_kthread+0x146/0x180 [btrfs]
[64036.654450] ? btrfs_cleanup_transaction+0x620/0x620 [btrfs]
[64036.654456] kthread+0x103/0x140
[64036.654464] ? kthread_create_worker_on_cpu+0x70/0x70
[64036.654476] ret_from_fork+0x3a/0x50
[64036.654504] INFO: task xfs_io:3919 blocked for more than 120 seconds.
[64036.654568] Not tainted 5.2.0-rc4-btrfs-next-50 #1
[64036.654617] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[64036.654685] xfs_io D 0 3919 3633 0x00000000
[64036.654691] Call Trace:
[64036.654703] ? __schedule+0x3ae/0x7b0
[64036.654716] schedule+0x3a/0xb0
[64036.654756] btrfs_find_free_ino+0xa9/0x120 [btrfs]
[64036.654764] ? remove_wait_queue+0x60/0x60
[64036.654809] btrfs_create+0x72/0x1f0 [btrfs]
[64036.654822] lookup_open+0x6bc/0x790
[64036.654849] path_openat+0x3bc/0xc00
[64036.654854] ? __lock_acquire+0x331/0x1cb0
[64036.654869] do_filp_open+0x99/0x110
[64036.654884] ? __alloc_fd+0xee/0x200
[64036.654895] ? do_raw_spin_unlock+0x49/0xc0
[64036.654909] ? do_sys_open+0x132/0x220
[64036.654913] do_sys_open+0x132/0x220
[64036.654926] do_syscall_64+0x60/0x1d0
[64036.654933] entry_SYSCALL_64_after_hwframe+0x49/0xbe
Fix this by adding a wake_up() call right after setting the cache state to
BTRFS_CACHE_FINISHED, at start_caching(), when we are able to load the
cache from disk.
Fixes: 82d5902d9c681b ("Btrfs: Support reading/writing on disk free ino cache") Reviewed-by: Nikolay Borisov <nborisov@suse.com> Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
NETDEV_TX_BUSY really should only be used by drivers that call
netif_tx_stop_queue() at the wrong moment. If dma_map_single() is
failed to map tx DMA buffer, it might trigger an infinite loop.
This patch use NETDEV_TX_OK instead of NETDEV_TX_BUSY, and change
printk to pr_err_ratelimited.
Fixes: d9fb9f384292 ("*sonic/natsemi/ns83829: Move the National Semi-conductor drivers") Signed-off-by: Mao Wenan <maowenan@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When dealing with 32-bit variant of LPUART IP block appropriate I/O
helpers have to be used to properly deal with endianness
differences. Change all of the offending code to do that.
Fixes: a5fa2660d787 ("tty/serial/fsl_lpuart: Add CONSOLE_POLL support
for lpuart32.") Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Cc: Stefan Agner <stefan@agner.ch> Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com> Cc: Chris Healy <cphealy@gmail.com> Cc: Cory Tusar <cory.tusar@zii.aero> Cc: Lucas Stach <l.stach@pengutronix.de> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: linux-imx@nxp.com Cc: linux-serial@vger.kernel.org Cc: linux-kernel@vger.kernel.org Link: https://lore.kernel.org/r/20190729195226.8862-14-andrew.smirnov@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Currently the pointer val is being incorrectly incremented
instead of the value pointed to by val. Fix this by adding
in the missing * indirection operator.
Addresses-Coverity: ("Unused value") Fixes: c03f2c536818 ("staging:iio:dac: Add AD5380 driver") Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
An earlier commit re-worked the setting of the bitmask and is now
assigning v with some bit flags rather than bitwise or-ing them
into v, consequently the earlier bit-settings of v are being lost.
Fix this by replacing an assignment with the bitwise or instead.
Addresses-Coverity: ("Unused value") Fixes: 2be25cac8402 ("bcma: add constants for PCI and use them") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Recently device pass-through stops working for Linux VM running on Hyper-V.
git-bisect shows the regression is caused by the recent commit 467a3bb97432 ("PCI: hv: Allocate a named fwnode ..."), but the root cause
is that the commit d59f6617eef0 forgets to set the domain->fwnode for
IRQCHIP_FWNODE_NAMED*, and as a result:
1. The domain->fwnode remains to be NULL.
2. irq_find_matching_fwspec() returns NULL since "h->fwnode == fwnode" is
false, and pci_set_bus_msi_domain() sets the Hyper-V PCI root bus's
msi_domain to NULL.
3. When the device is added onto the root bus, the device's dev->msi_domain
is set to NULL in pci_set_msi_domain().
4. When a device driver tries to enable MSI-X, pci_msi_setup_msi_irqs()
calls arch_setup_msi_irqs(), which uses the native MSI chip (i.e.
arch/x86/kernel/apic/msi.c: pci_msi_controller) to set up the irqs, but
actually pci_msi_setup_msi_irqs() is supposed to call
msi_domain_alloc_irqs() with the hbus->irq_domain, which is created in
hv_pcie_init_irq_domain() and is associated with the Hyper-V chip
hv_msi_irq_chip. Consequently, the irq line is not properly set up, and
the device driver can not receive any interrupt.
Fixes: d59f6617eef0 ("genirq: Allow fwnode to carry name information only") Fixes: 467a3bb97432 ("PCI: hv: Allocate a named fwnode instead of an address-based one") Reported-by: Lili Deng <v-lide@microsoft.com> Signed-off-by: Dexuan Cui <decui@microsoft.com> Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/PU1P153MB01694D9AF625AC335C600C5FBFBE0@PU1P153MB0169.APCP153.PROD.OUTLOOK.COM Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The problem is in gb_lights_request_handler(). If we get a request to
change the config then we release the light with gb_lights_light_release()
and re-allocated it. However, if the allocation fails part way through
then we call gb_lights_light_release() again. This can lead to a couple
different double frees where we haven't cleared out the original values:
I also made a small change to how we set "light->channels_count = 0;".
The original code handled this part fine and did not cause a use after
free but it was sort of complicated to read.
We may want to use the device pointer in device_init_wakeup() with
functions that expect the device to already be added with device_add().
For example, if we were to link the device initializing wakeup to
something in sysfs such as a class for wakeups we'll run into an error.
It looks like this code was written with the assumption that the device
would be added before initializing wakeup due to the order of operations
in power_supply_unregister().
Let's change the order of operations so we don't run into problems here.
Fixes: 948dcf966228 ("power_supply: Prevent suspend until power supply events are processed") Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Tri Vo <trong@android.com> Cc: Kalesh Singh <kaleshsingh@google.com> Cc: Ravi Chandra Sadineni <ravisadineni@chromium.org> Cc: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Stephen Boyd <swboyd@chromium.org> Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Writes into limit registers fail if the temperature written is negative.
The regmap write operation checks the value range, regmap_write accepts
an unsigned int as parameter, and the temperature value passed to
regmap_write is kept in a variable declared as long. Negative values
are converted large unsigned integers, which fails the range check.
Fix by type casting the temperature to u16 when calling regmap_write().
Cc: Iker Perez del Palomar Sustatxa <iker.perez@codethink.co.uk> Fixes: e65365fed87f ("hwmon: (lm75) Convert to use regmap") Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Commit dfe2a77fd243 ("kfifo: fix kfifo_alloc() and kfifo_init()") made
the kfifo code round the number of elements up. That was good for
__kfifo_alloc(), but it's actually wrong for __kfifo_init().
The difference? __kfifo_alloc() will allocate the rounded-up number of
elements, but __kfifo_init() uses an allocation done by the caller. We
can't just say "use more elements than the caller allocated", and have
to round down.
The good news? All the normal cases will be using power-of-two arrays
anyway, and most users of kfifo's don't use kfifo_init() at all, but one
of the helper macros to declare a KFIFO that enforce the proper
power-of-two behavior. But it looks like at least ibmvscsis might be
affected.
The bad news? Will Deacon refers to an old thread and points points out
that the memory ordering in kfifo's is questionable. See