2 This file provides some helper functions which are specific for EMMC device.
4 Copyright (c) 2018, NVIDIA CORPORATION. All rights reserved.
5 Copyright (c) 2015 - 2016, Intel Corporation. All rights reserved.<BR>
6 SPDX-License-Identifier: BSD-2-Clause-Patent
10 #include "SdMmcPciHcDxe.h"
13 Send command GO_IDLE_STATE (CMD0 with argument of 0x00000000) to the device to
14 make it go to Idle State.
16 Refer to EMMC Electrical Standard Spec 5.1 Section 6.4 for details.
18 @param[in] PassThru A pointer to the EFI_SD_MMC_PASS_THRU_PROTOCOL instance.
19 @param[in] Slot The slot number of the SD card to send the command to.
21 @retval EFI_SUCCESS The EMMC device is reset correctly.
22 @retval Others The device reset fails.
27 IN EFI_SD_MMC_PASS_THRU_PROTOCOL
*PassThru
,
31 EFI_SD_MMC_COMMAND_BLOCK SdMmcCmdBlk
;
32 EFI_SD_MMC_STATUS_BLOCK SdMmcStatusBlk
;
33 EFI_SD_MMC_PASS_THRU_COMMAND_PACKET Packet
;
36 ZeroMem (&SdMmcCmdBlk
, sizeof (SdMmcCmdBlk
));
37 ZeroMem (&SdMmcStatusBlk
, sizeof (SdMmcStatusBlk
));
38 ZeroMem (&Packet
, sizeof (Packet
));
40 Packet
.SdMmcCmdBlk
= &SdMmcCmdBlk
;
41 Packet
.SdMmcStatusBlk
= &SdMmcStatusBlk
;
42 Packet
.Timeout
= SD_MMC_HC_GENERIC_TIMEOUT
;
44 SdMmcCmdBlk
.CommandIndex
= EMMC_GO_IDLE_STATE
;
45 SdMmcCmdBlk
.CommandType
= SdMmcCommandTypeBc
;
46 SdMmcCmdBlk
.ResponseType
= 0;
47 SdMmcCmdBlk
.CommandArgument
= 0;
51 Status
= SdMmcPassThruPassThru (PassThru
, Slot
, &Packet
, NULL
);
57 Send command SEND_OP_COND to the EMMC device to get the data of the OCR register.
59 Refer to EMMC Electrical Standard Spec 5.1 Section 6.4 for details.
61 @param[in] PassThru A pointer to the EFI_SD_MMC_PASS_THRU_PROTOCOL instance.
62 @param[in] Slot The slot number of the SD card to send the command to.
63 @param[in, out] Argument On input, the argument of SEND_OP_COND is to send to the device.
64 On output, the argument is the value of OCR register.
66 @retval EFI_SUCCESS The operation is done correctly.
67 @retval Others The operation fails.
72 IN EFI_SD_MMC_PASS_THRU_PROTOCOL
*PassThru
,
74 IN OUT UINT32
*Argument
77 EFI_SD_MMC_COMMAND_BLOCK SdMmcCmdBlk
;
78 EFI_SD_MMC_STATUS_BLOCK SdMmcStatusBlk
;
79 EFI_SD_MMC_PASS_THRU_COMMAND_PACKET Packet
;
82 ZeroMem (&SdMmcCmdBlk
, sizeof (SdMmcCmdBlk
));
83 ZeroMem (&SdMmcStatusBlk
, sizeof (SdMmcStatusBlk
));
84 ZeroMem (&Packet
, sizeof (Packet
));
86 Packet
.SdMmcCmdBlk
= &SdMmcCmdBlk
;
87 Packet
.SdMmcStatusBlk
= &SdMmcStatusBlk
;
88 Packet
.Timeout
= SD_MMC_HC_GENERIC_TIMEOUT
;
90 SdMmcCmdBlk
.CommandIndex
= EMMC_SEND_OP_COND
;
91 SdMmcCmdBlk
.CommandType
= SdMmcCommandTypeBcr
;
92 SdMmcCmdBlk
.ResponseType
= SdMmcResponseTypeR3
;
93 SdMmcCmdBlk
.CommandArgument
= *Argument
;
95 Status
= SdMmcPassThruPassThru (PassThru
, Slot
, &Packet
, NULL
);
96 if (!EFI_ERROR (Status
)) {
98 // For details, refer to SD Host Controller Simplified Spec 3.0 Table 2-12.
100 *Argument
= SdMmcStatusBlk
.Resp0
;
107 Broadcast command ALL_SEND_CID to the bus to ask all the EMMC devices to send the
108 data of their CID registers.
110 Refer to EMMC Electrical Standard Spec 5.1 Section 6.4 for details.
112 @param[in] PassThru A pointer to the EFI_SD_MMC_PASS_THRU_PROTOCOL instance.
113 @param[in] Slot The slot number of the SD card to send the command to.
115 @retval EFI_SUCCESS The operation is done correctly.
116 @retval Others The operation fails.
121 IN EFI_SD_MMC_PASS_THRU_PROTOCOL
*PassThru
,
125 EFI_SD_MMC_COMMAND_BLOCK SdMmcCmdBlk
;
126 EFI_SD_MMC_STATUS_BLOCK SdMmcStatusBlk
;
127 EFI_SD_MMC_PASS_THRU_COMMAND_PACKET Packet
;
130 ZeroMem (&SdMmcCmdBlk
, sizeof (SdMmcCmdBlk
));
131 ZeroMem (&SdMmcStatusBlk
, sizeof (SdMmcStatusBlk
));
132 ZeroMem (&Packet
, sizeof (Packet
));
134 Packet
.SdMmcCmdBlk
= &SdMmcCmdBlk
;
135 Packet
.SdMmcStatusBlk
= &SdMmcStatusBlk
;
136 Packet
.Timeout
= SD_MMC_HC_GENERIC_TIMEOUT
;
138 SdMmcCmdBlk
.CommandIndex
= EMMC_ALL_SEND_CID
;
139 SdMmcCmdBlk
.CommandType
= SdMmcCommandTypeBcr
;
140 SdMmcCmdBlk
.ResponseType
= SdMmcResponseTypeR2
;
141 SdMmcCmdBlk
.CommandArgument
= 0;
143 Status
= SdMmcPassThruPassThru (PassThru
, Slot
, &Packet
, NULL
);
149 Send command SET_RELATIVE_ADDR to the EMMC device to assign a Relative device
152 Refer to EMMC Electrical Standard Spec 5.1 Section 6.4 for details.
154 @param[in] PassThru A pointer to the EFI_SD_MMC_PASS_THRU_PROTOCOL instance.
155 @param[in] Slot The slot number of the SD card to send the command to.
156 @param[in] Rca The relative device address to be assigned.
158 @retval EFI_SUCCESS The operation is done correctly.
159 @retval Others The operation fails.
164 IN EFI_SD_MMC_PASS_THRU_PROTOCOL
*PassThru
,
169 EFI_SD_MMC_COMMAND_BLOCK SdMmcCmdBlk
;
170 EFI_SD_MMC_STATUS_BLOCK SdMmcStatusBlk
;
171 EFI_SD_MMC_PASS_THRU_COMMAND_PACKET Packet
;
174 ZeroMem (&SdMmcCmdBlk
, sizeof (SdMmcCmdBlk
));
175 ZeroMem (&SdMmcStatusBlk
, sizeof (SdMmcStatusBlk
));
176 ZeroMem (&Packet
, sizeof (Packet
));
178 Packet
.SdMmcCmdBlk
= &SdMmcCmdBlk
;
179 Packet
.SdMmcStatusBlk
= &SdMmcStatusBlk
;
180 Packet
.Timeout
= SD_MMC_HC_GENERIC_TIMEOUT
;
182 SdMmcCmdBlk
.CommandIndex
= EMMC_SET_RELATIVE_ADDR
;
183 SdMmcCmdBlk
.CommandType
= SdMmcCommandTypeAc
;
184 SdMmcCmdBlk
.ResponseType
= SdMmcResponseTypeR1
;
185 SdMmcCmdBlk
.CommandArgument
= (UINT32
)Rca
<< 16;
187 Status
= SdMmcPassThruPassThru (PassThru
, Slot
, &Packet
, NULL
);
193 Send command SEND_CSD to the EMMC device to get the data of the CSD register.
195 Refer to EMMC Electrical Standard Spec 5.1 Section 6.10.4 for details.
197 @param[in] PassThru A pointer to the EFI_SD_MMC_PASS_THRU_PROTOCOL instance.
198 @param[in] Slot The slot number of the SD card to send the command to.
199 @param[in] Rca The relative device address of selected device.
200 @param[out] Csd The buffer to store the content of the CSD register.
201 Note the caller should ignore the lowest byte of this
202 buffer as the content of this byte is meaningless even
203 if the operation succeeds.
205 @retval EFI_SUCCESS The operation is done correctly.
206 @retval Others The operation fails.
211 IN EFI_SD_MMC_PASS_THRU_PROTOCOL
*PassThru
,
217 EFI_SD_MMC_COMMAND_BLOCK SdMmcCmdBlk
;
218 EFI_SD_MMC_STATUS_BLOCK SdMmcStatusBlk
;
219 EFI_SD_MMC_PASS_THRU_COMMAND_PACKET Packet
;
222 ZeroMem (&SdMmcCmdBlk
, sizeof (SdMmcCmdBlk
));
223 ZeroMem (&SdMmcStatusBlk
, sizeof (SdMmcStatusBlk
));
224 ZeroMem (&Packet
, sizeof (Packet
));
226 Packet
.SdMmcCmdBlk
= &SdMmcCmdBlk
;
227 Packet
.SdMmcStatusBlk
= &SdMmcStatusBlk
;
228 Packet
.Timeout
= SD_MMC_HC_GENERIC_TIMEOUT
;
230 SdMmcCmdBlk
.CommandIndex
= EMMC_SEND_CSD
;
231 SdMmcCmdBlk
.CommandType
= SdMmcCommandTypeAc
;
232 SdMmcCmdBlk
.ResponseType
= SdMmcResponseTypeR2
;
233 SdMmcCmdBlk
.CommandArgument
= (UINT32
)Rca
<< 16;
235 Status
= SdMmcPassThruPassThru (PassThru
, Slot
, &Packet
, NULL
);
236 if (!EFI_ERROR (Status
)) {
238 // For details, refer to SD Host Controller Simplified Spec 3.0 Table 2-12.
240 CopyMem (((UINT8
*)Csd
) + 1, &SdMmcStatusBlk
.Resp0
, sizeof (EMMC_CSD
) - 1);
247 Send command SELECT_DESELECT_CARD to the EMMC device to select/deselect it.
249 Refer to EMMC Electrical Standard Spec 5.1 Section 6.10.4 for details.
251 @param[in] PassThru A pointer to the EFI_SD_MMC_PASS_THRU_PROTOCOL instance.
252 @param[in] Slot The slot number of the SD card to send the command to.
253 @param[in] Rca The relative device address of selected device.
255 @retval EFI_SUCCESS The operation is done correctly.
256 @retval Others The operation fails.
261 IN EFI_SD_MMC_PASS_THRU_PROTOCOL
*PassThru
,
266 EFI_SD_MMC_COMMAND_BLOCK SdMmcCmdBlk
;
267 EFI_SD_MMC_STATUS_BLOCK SdMmcStatusBlk
;
268 EFI_SD_MMC_PASS_THRU_COMMAND_PACKET Packet
;
271 ZeroMem (&SdMmcCmdBlk
, sizeof (SdMmcCmdBlk
));
272 ZeroMem (&SdMmcStatusBlk
, sizeof (SdMmcStatusBlk
));
273 ZeroMem (&Packet
, sizeof (Packet
));
275 Packet
.SdMmcCmdBlk
= &SdMmcCmdBlk
;
276 Packet
.SdMmcStatusBlk
= &SdMmcStatusBlk
;
277 Packet
.Timeout
= SD_MMC_HC_GENERIC_TIMEOUT
;
279 SdMmcCmdBlk
.CommandIndex
= EMMC_SELECT_DESELECT_CARD
;
280 SdMmcCmdBlk
.CommandType
= SdMmcCommandTypeAc
;
281 SdMmcCmdBlk
.ResponseType
= SdMmcResponseTypeR1
;
282 SdMmcCmdBlk
.CommandArgument
= (UINT32
)Rca
<< 16;
284 Status
= SdMmcPassThruPassThru (PassThru
, Slot
, &Packet
, NULL
);
290 Send command SEND_EXT_CSD to the EMMC device to get the data of the EXT_CSD register.
292 Refer to EMMC Electrical Standard Spec 5.1 Section 6.10.4 for details.
294 @param[in] PassThru A pointer to the EFI_SD_MMC_PASS_THRU_PROTOCOL instance.
295 @param[in] Slot The slot number of the SD card to send the command to.
296 @param[out] ExtCsd The buffer to store the content of the EXT_CSD register.
298 @retval EFI_SUCCESS The operation is done correctly.
299 @retval Others The operation fails.
304 IN EFI_SD_MMC_PASS_THRU_PROTOCOL
*PassThru
,
306 OUT EMMC_EXT_CSD
*ExtCsd
309 EFI_SD_MMC_COMMAND_BLOCK SdMmcCmdBlk
;
310 EFI_SD_MMC_STATUS_BLOCK SdMmcStatusBlk
;
311 EFI_SD_MMC_PASS_THRU_COMMAND_PACKET Packet
;
314 ZeroMem (&SdMmcCmdBlk
, sizeof (SdMmcCmdBlk
));
315 ZeroMem (&SdMmcStatusBlk
, sizeof (SdMmcStatusBlk
));
316 ZeroMem (&Packet
, sizeof (Packet
));
318 Packet
.SdMmcCmdBlk
= &SdMmcCmdBlk
;
319 Packet
.SdMmcStatusBlk
= &SdMmcStatusBlk
;
320 Packet
.Timeout
= SD_MMC_HC_GENERIC_TIMEOUT
;
322 SdMmcCmdBlk
.CommandIndex
= EMMC_SEND_EXT_CSD
;
323 SdMmcCmdBlk
.CommandType
= SdMmcCommandTypeAdtc
;
324 SdMmcCmdBlk
.ResponseType
= SdMmcResponseTypeR1
;
325 SdMmcCmdBlk
.CommandArgument
= 0x00000000;
327 Packet
.InDataBuffer
= ExtCsd
;
328 Packet
.InTransferLength
= sizeof (EMMC_EXT_CSD
);
330 Status
= SdMmcPassThruPassThru (PassThru
, Slot
, &Packet
, NULL
);
335 Send command SWITCH to the EMMC device to switch the mode of operation of the
336 selected Device or modifies the EXT_CSD registers.
338 Refer to EMMC Electrical Standard Spec 5.1 Section 6.10.4 for details.
340 @param[in] PassThru A pointer to the EFI_SD_MMC_PASS_THRU_PROTOCOL instance.
341 @param[in] Slot The slot number of the SD card to send the command to.
342 @param[in] Access The access mode of SWTICH command.
343 @param[in] Index The offset of the field to be access.
344 @param[in] Value The value to be set to the specified field of EXT_CSD register.
345 @param[in] CmdSet The value of CmdSet field of EXT_CSD register.
347 @retval EFI_SUCCESS The operation is done correctly.
348 @retval Others The operation fails.
353 IN EFI_SD_MMC_PASS_THRU_PROTOCOL
*PassThru
,
361 EFI_SD_MMC_COMMAND_BLOCK SdMmcCmdBlk
;
362 EFI_SD_MMC_STATUS_BLOCK SdMmcStatusBlk
;
363 EFI_SD_MMC_PASS_THRU_COMMAND_PACKET Packet
;
366 ZeroMem (&SdMmcCmdBlk
, sizeof (SdMmcCmdBlk
));
367 ZeroMem (&SdMmcStatusBlk
, sizeof (SdMmcStatusBlk
));
368 ZeroMem (&Packet
, sizeof (Packet
));
370 Packet
.SdMmcCmdBlk
= &SdMmcCmdBlk
;
371 Packet
.SdMmcStatusBlk
= &SdMmcStatusBlk
;
372 Packet
.Timeout
= SD_MMC_HC_GENERIC_TIMEOUT
;
374 SdMmcCmdBlk
.CommandIndex
= EMMC_SWITCH
;
375 SdMmcCmdBlk
.CommandType
= SdMmcCommandTypeAc
;
376 SdMmcCmdBlk
.ResponseType
= SdMmcResponseTypeR1b
;
377 SdMmcCmdBlk
.CommandArgument
= (Access
<< 24) | (Index
<< 16) | (Value
<< 8) | CmdSet
;
379 Status
= SdMmcPassThruPassThru (PassThru
, Slot
, &Packet
, NULL
);
385 Send command SEND_STATUS to the addressed EMMC device to get its status register.
387 Refer to EMMC Electrical Standard Spec 5.1 Section 6.10.4 for details.
389 @param[in] PassThru A pointer to the EFI_SD_MMC_PASS_THRU_PROTOCOL instance.
390 @param[in] Slot The slot number of the SD card to send the command to.
391 @param[in] Rca The relative device address of addressed device.
392 @param[out] DevStatus The returned device status.
394 @retval EFI_SUCCESS The operation is done correctly.
395 @retval Others The operation fails.
400 IN EFI_SD_MMC_PASS_THRU_PROTOCOL
*PassThru
,
403 OUT UINT32
*DevStatus
406 EFI_SD_MMC_COMMAND_BLOCK SdMmcCmdBlk
;
407 EFI_SD_MMC_STATUS_BLOCK SdMmcStatusBlk
;
408 EFI_SD_MMC_PASS_THRU_COMMAND_PACKET Packet
;
411 ZeroMem (&SdMmcCmdBlk
, sizeof (SdMmcCmdBlk
));
412 ZeroMem (&SdMmcStatusBlk
, sizeof (SdMmcStatusBlk
));
413 ZeroMem (&Packet
, sizeof (Packet
));
415 Packet
.SdMmcCmdBlk
= &SdMmcCmdBlk
;
416 Packet
.SdMmcStatusBlk
= &SdMmcStatusBlk
;
417 Packet
.Timeout
= SD_MMC_HC_GENERIC_TIMEOUT
;
419 SdMmcCmdBlk
.CommandIndex
= EMMC_SEND_STATUS
;
420 SdMmcCmdBlk
.CommandType
= SdMmcCommandTypeAc
;
421 SdMmcCmdBlk
.ResponseType
= SdMmcResponseTypeR1
;
422 SdMmcCmdBlk
.CommandArgument
= (UINT32
)Rca
<< 16;
424 Status
= SdMmcPassThruPassThru (PassThru
, Slot
, &Packet
, NULL
);
425 if (!EFI_ERROR (Status
)) {
426 *DevStatus
= SdMmcStatusBlk
.Resp0
;
433 Send command SEND_TUNING_BLOCK to the EMMC device for HS200 optimal sampling point
436 It may be sent up to 40 times until the host finishes the tuning procedure.
438 Refer to EMMC Electrical Standard Spec 5.1 Section 6.6.8 for details.
440 @param[in] PassThru A pointer to the EFI_SD_MMC_PASS_THRU_PROTOCOL instance.
441 @param[in] Slot The slot number of the SD card to send the command to.
442 @param[in] BusWidth The bus width to work.
444 @retval EFI_SUCCESS The operation is done correctly.
445 @retval Others The operation fails.
450 IN EFI_SD_MMC_PASS_THRU_PROTOCOL
*PassThru
,
455 EFI_SD_MMC_COMMAND_BLOCK SdMmcCmdBlk
;
456 EFI_SD_MMC_STATUS_BLOCK SdMmcStatusBlk
;
457 EFI_SD_MMC_PASS_THRU_COMMAND_PACKET Packet
;
459 UINT8 TuningBlock
[128];
461 ZeroMem (&SdMmcCmdBlk
, sizeof (SdMmcCmdBlk
));
462 ZeroMem (&SdMmcStatusBlk
, sizeof (SdMmcStatusBlk
));
463 ZeroMem (&Packet
, sizeof (Packet
));
465 Packet
.SdMmcCmdBlk
= &SdMmcCmdBlk
;
466 Packet
.SdMmcStatusBlk
= &SdMmcStatusBlk
;
467 Packet
.Timeout
= SD_MMC_HC_GENERIC_TIMEOUT
;
469 SdMmcCmdBlk
.CommandIndex
= EMMC_SEND_TUNING_BLOCK
;
470 SdMmcCmdBlk
.CommandType
= SdMmcCommandTypeAdtc
;
471 SdMmcCmdBlk
.ResponseType
= SdMmcResponseTypeR1
;
472 SdMmcCmdBlk
.CommandArgument
= 0;
474 Packet
.InDataBuffer
= TuningBlock
;
476 Packet
.InTransferLength
= sizeof (TuningBlock
);
478 Packet
.InTransferLength
= 64;
481 Status
= SdMmcPassThruPassThru (PassThru
, Slot
, &Packet
, NULL
);
487 Tunning the clock to get HS200 optimal sampling point.
489 Command SEND_TUNING_BLOCK may be sent up to 40 times until the host finishes the
492 Refer to EMMC Electrical Standard Spec 5.1 Section 6.6.8 and SD Host Controller
493 Simplified Spec 3.0 Figure 2-29 for details.
495 @param[in] PciIo A pointer to the EFI_PCI_IO_PROTOCOL instance.
496 @param[in] PassThru A pointer to the EFI_SD_MMC_PASS_THRU_PROTOCOL instance.
497 @param[in] Slot The slot number of the SD card to send the command to.
498 @param[in] BusWidth The bus width to work.
500 @retval EFI_SUCCESS The operation is done correctly.
501 @retval Others The operation fails.
505 EmmcTuningClkForHs200 (
506 IN EFI_PCI_IO_PROTOCOL
*PciIo
,
507 IN EFI_SD_MMC_PASS_THRU_PROTOCOL
*PassThru
,
517 // Notify the host that the sampling clock tuning procedure starts.
520 Status
= SdMmcHcOrMmio (PciIo
, Slot
, SD_MMC_HC_HOST_CTRL2
, sizeof (HostCtrl2
), &HostCtrl2
);
521 if (EFI_ERROR (Status
)) {
525 // Ask the device to send a sequence of tuning blocks till the tuning procedure is done.
529 Status
= EmmcSendTuningBlk (PassThru
, Slot
, BusWidth
);
530 if (EFI_ERROR (Status
)) {
531 DEBUG ((DEBUG_ERROR
, "EmmcTuningClkForHs200: Send tuning block fails with %r\n", Status
));
535 Status
= SdMmcHcRwMmio (PciIo
, Slot
, SD_MMC_HC_HOST_CTRL2
, TRUE
, sizeof (HostCtrl2
), &HostCtrl2
);
536 if (EFI_ERROR (Status
)) {
540 if ((HostCtrl2
& (BIT6
| BIT7
)) == 0) {
544 if ((HostCtrl2
& (BIT6
| BIT7
)) == BIT7
) {
547 } while (++Retry
< 40);
549 DEBUG ((DEBUG_ERROR
, "EmmcTuningClkForHs200: Send tuning block fails at %d times with HostCtrl2 %02x\n", Retry
, HostCtrl2
));
551 // Abort the tuning procedure and reset the tuning circuit.
553 HostCtrl2
= (UINT8
)~(BIT6
| BIT7
);
554 Status
= SdMmcHcAndMmio (PciIo
, Slot
, SD_MMC_HC_HOST_CTRL2
, sizeof (HostCtrl2
), &HostCtrl2
);
555 if (EFI_ERROR (Status
)) {
558 return EFI_DEVICE_ERROR
;
562 Switch the bus width to specified width.
564 Refer to EMMC Electrical Standard Spec 5.1 Section 6.6.9 and SD Host Controller
565 Simplified Spec 3.0 Figure 3-7 for details.
567 @param[in] PciIo A pointer to the EFI_PCI_IO_PROTOCOL instance.
568 @param[in] PassThru A pointer to the EFI_SD_MMC_PASS_THRU_PROTOCOL instance.
569 @param[in] Slot The slot number of the SD card to send the command to.
570 @param[in] Rca The relative device address to be assigned.
571 @param[in] IsDdr If TRUE, use dual data rate data simpling method. Otherwise
572 use single data rate data simpling method.
573 @param[in] BusWidth The bus width to be set, it could be 4 or 8.
575 @retval EFI_SUCCESS The operation is done correctly.
576 @retval Others The operation fails.
581 IN EFI_PCI_IO_PROTOCOL
*PciIo
,
582 IN EFI_SD_MMC_PASS_THRU_PROTOCOL
*PassThru
,
597 // Write Byte, the Value field is written into the byte pointed by Index.
600 Index
= OFFSET_OF (EMMC_EXT_CSD
, BusWidth
);
603 } else if (BusWidth
== 8) {
606 return EFI_INVALID_PARAMETER
;
614 Status
= EmmcSwitch (PassThru
, Slot
, Access
, Index
, Value
, CmdSet
);
615 if (EFI_ERROR (Status
)) {
616 DEBUG ((DEBUG_ERROR
, "EmmcSwitchBusWidth: Switch to bus width %d fails with %r\n", BusWidth
, Status
));
620 Status
= EmmcSendStatus (PassThru
, Slot
, Rca
, &DevStatus
);
621 if (EFI_ERROR (Status
)) {
622 DEBUG ((DEBUG_ERROR
, "EmmcSwitchBusWidth: Send status fails with %r\n", Status
));
626 // Check the switch operation is really successful or not.
628 if ((DevStatus
& BIT7
) != 0) {
629 DEBUG ((DEBUG_ERROR
, "EmmcSwitchBusWidth: The switch operation fails as DevStatus is 0x%08x\n", DevStatus
));
630 return EFI_DEVICE_ERROR
;
633 Status
= SdMmcHcSetBusWidth (PciIo
, Slot
, BusWidth
);
639 Switch the bus timing and clock frequency.
641 Refer to EMMC Electrical Standard Spec 5.1 Section 6.6 and SD Host Controller
642 Simplified Spec 3.0 Figure 3-3 for details.
644 @param[in] PciIo A pointer to the EFI_PCI_IO_PROTOCOL instance.
645 @param[in] PassThru A pointer to the EFI_SD_MMC_PASS_THRU_PROTOCOL instance.
646 @param[in] Slot The slot number of the SD card to send the command to.
647 @param[in] Rca The relative device address to be assigned.
648 @param[in] DriverStrength Driver strength to set for speed modes that support it.
649 @param[in] BusTiming The bus mode timing indicator.
650 @param[in] ClockFreq The max clock frequency to be set, the unit is MHz.
652 @retval EFI_SUCCESS The operation is done correctly.
653 @retval Others The operation fails.
657 EmmcSwitchBusTiming (
658 IN EFI_PCI_IO_PROTOCOL
*PciIo
,
659 IN EFI_SD_MMC_PASS_THRU_PROTOCOL
*PassThru
,
662 IN EDKII_SD_MMC_DRIVER_STRENGTH DriverStrength
,
663 IN SD_MMC_BUS_MODE BusTiming
,
673 SD_MMC_HC_PRIVATE_DATA
*Private
;
676 Private
= SD_MMC_HC_PRIVATE_FROM_THIS (PassThru
);
678 // Write Byte, the Value field is written into the byte pointed by Index.
681 Index
= OFFSET_OF (EMMC_EXT_CSD
, HsTiming
);
685 Value
= (UINT8
)((DriverStrength
.Emmc
<< 4) | 3);
688 Value
= (UINT8
)((DriverStrength
.Emmc
<< 4) | 2);
698 DEBUG ((DEBUG_ERROR
, "EmmcSwitchBusTiming: Unsupported BusTiming(%d\n)", BusTiming
));
699 return EFI_INVALID_PARAMETER
;
702 Status
= EmmcSwitch (PassThru
, Slot
, Access
, Index
, Value
, CmdSet
);
703 if (EFI_ERROR (Status
)) {
704 DEBUG ((DEBUG_ERROR
, "EmmcSwitchBusTiming: Switch to bus timing %d fails with %r\n", BusTiming
, Status
));
708 if (BusTiming
== SdMmcMmcHsSdr
|| BusTiming
== SdMmcMmcHsDdr
) {
710 Status
= SdMmcHcOrMmio (PciIo
, Slot
, SD_MMC_HC_HOST_CTRL1
, sizeof (HostCtrl1
), &HostCtrl1
);
711 if (EFI_ERROR (Status
)) {
715 HostCtrl1
= (UINT8
)~BIT2
;
716 Status
= SdMmcHcAndMmio (PciIo
, Slot
, SD_MMC_HC_HOST_CTRL1
, sizeof (HostCtrl1
), &HostCtrl1
);
717 if (EFI_ERROR (Status
)) {
722 Status
= SdMmcHcUhsSignaling (Private
->ControllerHandle
, PciIo
, Slot
, BusTiming
);
723 if (EFI_ERROR (Status
)) {
728 // Convert the clock freq unit from MHz to KHz.
730 Status
= SdMmcHcClockSupply (PciIo
, Slot
, ClockFreq
* 1000, Private
->BaseClkFreq
[Slot
], Private
->ControllerVersion
[Slot
]);
731 if (EFI_ERROR (Status
)) {
735 Status
= EmmcSendStatus (PassThru
, Slot
, Rca
, &DevStatus
);
736 if (EFI_ERROR (Status
)) {
737 DEBUG ((DEBUG_ERROR
, "EmmcSwitchBusTiming: Send status fails with %r\n", Status
));
741 // Check the switch operation is really successful or not.
743 if ((DevStatus
& BIT7
) != 0) {
744 DEBUG ((DEBUG_ERROR
, "EmmcSwitchBusTiming: The switch operation fails as DevStatus is 0x%08x\n", DevStatus
));
745 return EFI_DEVICE_ERROR
;
748 if (mOverride
!= NULL
&& mOverride
->NotifyPhase
!= NULL
) {
749 Status
= mOverride
->NotifyPhase (
750 Private
->ControllerHandle
,
752 EdkiiSdMmcSwitchClockFreqPost
,
755 if (EFI_ERROR (Status
)) {
758 "%a: SD/MMC switch clock freq post notifier callback failed - %r\n",
770 Switch to the High Speed timing according to request.
772 Refer to EMMC Electrical Standard Spec 5.1 Section 6.6.8 and SD Host Controller
773 Simplified Spec 3.0 Figure 2-29 for details.
775 @param[in] PciIo A pointer to the EFI_PCI_IO_PROTOCOL instance.
776 @param[in] PassThru A pointer to the EFI_SD_MMC_PASS_THRU_PROTOCOL instance.
777 @param[in] Slot The slot number of the SD card to send the command to.
778 @param[in] Rca The relative device address to be assigned.
779 @param[in] BusMode Pointer to SD_MMC_BUS_SETTINGS structure containing bus settings.
781 @retval EFI_SUCCESS The operation is done correctly.
782 @retval Others The operation fails.
786 EmmcSwitchToHighSpeed (
787 IN EFI_PCI_IO_PROTOCOL
*PciIo
,
788 IN EFI_SD_MMC_PASS_THRU_PROTOCOL
*PassThru
,
791 IN SD_MMC_BUS_SETTINGS
*BusMode
797 if ((BusMode
->BusTiming
!= SdMmcMmcHsSdr
&& BusMode
->BusTiming
!= SdMmcMmcHsDdr
) ||
798 BusMode
->ClockFreq
> 52) {
799 return EFI_INVALID_PARAMETER
;
802 if (BusMode
->BusTiming
== SdMmcMmcHsDdr
) {
808 Status
= EmmcSwitchBusWidth (PciIo
, PassThru
, Slot
, Rca
, IsDdr
, BusMode
->BusWidth
);
809 if (EFI_ERROR (Status
)) {
813 return EmmcSwitchBusTiming (PciIo
, PassThru
, Slot
, Rca
, BusMode
->DriverStrength
, BusMode
->BusTiming
, BusMode
->ClockFreq
);
817 Switch to the HS200 timing. This function assumes that eMMC bus is still in legacy mode.
819 Refer to EMMC Electrical Standard Spec 5.1 Section 6.6.8 and SD Host Controller
820 Simplified Spec 3.0 Figure 2-29 for details.
822 @param[in] PciIo A pointer to the EFI_PCI_IO_PROTOCOL instance.
823 @param[in] PassThru A pointer to the EFI_SD_MMC_PASS_THRU_PROTOCOL instance.
824 @param[in] Slot The slot number of the SD card to send the command to.
825 @param[in] Rca The relative device address to be assigned.
826 @param[in] BusMode Pointer to SD_MMC_BUS_SETTINGS structure containing bus settings.
828 @retval EFI_SUCCESS The operation is done correctly.
829 @retval Others The operation fails.
834 IN EFI_PCI_IO_PROTOCOL
*PciIo
,
835 IN EFI_SD_MMC_PASS_THRU_PROTOCOL
*PassThru
,
838 IN SD_MMC_BUS_SETTINGS
*BusMode
843 if (BusMode
->BusTiming
!= SdMmcMmcHs200
||
844 (BusMode
->BusWidth
!= 4 && BusMode
->BusWidth
!= 8)) {
845 return EFI_INVALID_PARAMETER
;
848 Status
= EmmcSwitchBusWidth (PciIo
, PassThru
, Slot
, Rca
, FALSE
, BusMode
->BusWidth
);
849 if (EFI_ERROR (Status
)) {
853 Status
= EmmcSwitchBusTiming (PciIo
, PassThru
, Slot
, Rca
, BusMode
->DriverStrength
, BusMode
->BusTiming
, BusMode
->ClockFreq
);
854 if (EFI_ERROR (Status
)) {
858 Status
= EmmcTuningClkForHs200 (PciIo
, PassThru
, Slot
, BusMode
->BusWidth
);
864 Switch to the HS400 timing. This function assumes that eMMC bus is still in legacy mode.
866 Refer to EMMC Electrical Standard Spec 5.1 Section 6.6.8 and SD Host Controller
867 Simplified Spec 3.0 Figure 2-29 for details.
869 @param[in] PciIo A pointer to the EFI_PCI_IO_PROTOCOL instance.
870 @param[in] PassThru A pointer to the EFI_SD_MMC_PASS_THRU_PROTOCOL instance.
871 @param[in] Slot The slot number of the SD card to send the command to.
872 @param[in] Rca The relative device address to be assigned.
873 @param[in] BusMode Pointer to SD_MMC_BUS_SETTINGS structure containing bus settings.
875 @retval EFI_SUCCESS The operation is done correctly.
876 @retval Others The operation fails.
881 IN EFI_PCI_IO_PROTOCOL
*PciIo
,
882 IN EFI_SD_MMC_PASS_THRU_PROTOCOL
*PassThru
,
885 IN SD_MMC_BUS_SETTINGS
*BusMode
889 SD_MMC_BUS_SETTINGS Hs200BusMode
;
892 if (BusMode
->BusTiming
!= SdMmcMmcHs400
||
893 BusMode
->BusWidth
!= 8) {
894 return EFI_INVALID_PARAMETER
;
897 Hs200BusMode
.BusTiming
= SdMmcMmcHs200
;
898 Hs200BusMode
.BusWidth
= BusMode
->BusWidth
;
899 Hs200BusMode
.ClockFreq
= BusMode
->ClockFreq
;
900 Hs200BusMode
.DriverStrength
= BusMode
->DriverStrength
;
902 Status
= EmmcSwitchToHS200 (PciIo
, PassThru
, Slot
, Rca
, &Hs200BusMode
);
903 if (EFI_ERROR (Status
)) {
908 // Set to High Speed timing and set the clock frequency to a value less than or equal to 52MHz.
909 // This step is necessary to be able to switch Bus into 8 bit DDR mode which is unsupported in HS200.
911 HsFreq
= BusMode
->ClockFreq
< 52 ? BusMode
->ClockFreq
: 52;
912 Status
= EmmcSwitchBusTiming (PciIo
, PassThru
, Slot
, Rca
, BusMode
->DriverStrength
, SdMmcMmcHsSdr
, HsFreq
);
913 if (EFI_ERROR (Status
)) {
917 Status
= EmmcSwitchBusWidth (PciIo
, PassThru
, Slot
, Rca
, TRUE
, BusMode
->BusWidth
);
918 if (EFI_ERROR (Status
)) {
922 return EmmcSwitchBusTiming (PciIo
, PassThru
, Slot
, Rca
, BusMode
->DriverStrength
, BusMode
->BusTiming
, BusMode
->ClockFreq
);
926 Check if passed BusTiming is supported in both controller and card.
928 @param[in] Private Pointer to controller private data
929 @param[in] SlotIndex Index of the slot in the controller
930 @param[in] ExtCsd Pointer to the card's extended CSD
931 @param[in] BusTiming Bus timing to check
933 @retval TRUE Both card and controller support given BusTiming
934 @retval FALSE Card or controller doesn't support given BusTiming
937 EmmcIsBusTimingSupported (
938 IN SD_MMC_HC_PRIVATE_DATA
*Private
,
940 IN EMMC_EXT_CSD
*ExtCsd
,
941 IN SD_MMC_BUS_MODE BusTiming
945 SD_MMC_HC_SLOT_CAP
*Capabilities
;
947 Capabilities
= &Private
->Capability
[SlotIndex
];
952 if ((((ExtCsd
->DeviceType
& (BIT6
| BIT7
)) != 0) && (Capabilities
->Hs400
!= 0)) && Capabilities
->BusWidth8
!= 0) {
957 if ((((ExtCsd
->DeviceType
& (BIT4
| BIT5
)) != 0) && (Capabilities
->Sdr104
!= 0))) {
962 if ((((ExtCsd
->DeviceType
& (BIT2
| BIT3
)) != 0) && (Capabilities
->Ddr50
!= 0))) {
967 if ((((ExtCsd
->DeviceType
& BIT1
) != 0) && (Capabilities
->HighSpeed
!= 0))) {
972 if ((ExtCsd
->DeviceType
& BIT0
) != 0) {
984 Get the target bus timing to set on the link. This function
985 will try to select highest bus timing supported by card, controller
988 @param[in] Private Pointer to controller private data
989 @param[in] SlotIndex Index of the slot in the controller
990 @param[in] ExtCsd Pointer to the card's extended CSD
992 @return Bus timing value that should be set on link
995 EmmcGetTargetBusTiming (
996 IN SD_MMC_HC_PRIVATE_DATA
*Private
,
998 IN EMMC_EXT_CSD
*ExtCsd
1001 SD_MMC_BUS_MODE BusTiming
;
1004 // We start with highest bus timing that this driver currently supports and
1005 // return as soon as we find supported timing.
1007 BusTiming
= SdMmcMmcHs400
;
1008 while (BusTiming
> SdMmcMmcLegacy
) {
1009 if (EmmcIsBusTimingSupported (Private
, SlotIndex
, ExtCsd
, BusTiming
)) {
1019 Check if the passed bus width is supported by controller and card.
1021 @param[in] Private Pointer to controller private data
1022 @param[in] SlotIndex Index of the slot in the controller
1023 @param[in] BusTiming Bus timing set on the link
1024 @param[in] BusWidth Bus width to check
1026 @retval TRUE Passed bus width is supported in current bus configuration
1027 @retval FALSE Passed bus width is not supported in current bus configuration
1030 EmmcIsBusWidthSupported (
1031 IN SD_MMC_HC_PRIVATE_DATA
*Private
,
1033 IN SD_MMC_BUS_MODE BusTiming
,
1037 if (BusWidth
== 8 && Private
->Capability
[SlotIndex
].BusWidth8
!= 0) {
1039 } else if (BusWidth
== 4 && BusTiming
!= SdMmcMmcHs400
) {
1041 } else if (BusWidth
== 1 && (BusTiming
== SdMmcMmcHsSdr
|| BusTiming
== SdMmcMmcLegacy
)) {
1049 Get the target bus width to be set on the bus.
1051 @param[in] Private Pointer to controller private data
1052 @param[in] SlotIndex Index of the slot in the controller
1053 @param[in] ExtCsd Pointer to card's extended CSD
1054 @param[in] BusTiming Bus timing set on the bus
1056 @return Bus width to be set on the bus
1059 EmmcGetTargetBusWidth (
1060 IN SD_MMC_HC_PRIVATE_DATA
*Private
,
1062 IN EMMC_EXT_CSD
*ExtCsd
,
1063 IN SD_MMC_BUS_MODE BusTiming
1067 UINT8 PreferredBusWidth
;
1069 PreferredBusWidth
= Private
->Slot
[SlotIndex
].OperatingParameters
.BusWidth
;
1071 if (PreferredBusWidth
!= EDKII_SD_MMC_BUS_WIDTH_IGNORE
&&
1072 EmmcIsBusWidthSupported (Private
, SlotIndex
, BusTiming
, PreferredBusWidth
)) {
1073 BusWidth
= PreferredBusWidth
;
1074 } else if (EmmcIsBusWidthSupported (Private
, SlotIndex
, BusTiming
, 8)) {
1076 } else if (EmmcIsBusWidthSupported (Private
, SlotIndex
, BusTiming
, 4)) {
1086 Get the target clock frequency to be set on the bus.
1088 @param[in] Private Pointer to controller private data
1089 @param[in] SlotIndex Index of the slot in the controller
1090 @param[in] ExtCsd Pointer to card's extended CSD
1091 @param[in] BusTiming Bus timing to be set on the bus
1093 @return Value of the clock frequency to be set on bus in MHz
1096 EmmcGetTargetClockFreq (
1097 IN SD_MMC_HC_PRIVATE_DATA
*Private
,
1099 IN EMMC_EXT_CSD
*ExtCsd
,
1100 IN SD_MMC_BUS_MODE BusTiming
1103 UINT32 PreferredClockFreq
;
1104 UINT32 MaxClockFreq
;
1106 PreferredClockFreq
= Private
->Slot
[SlotIndex
].OperatingParameters
.ClockFreq
;
1108 switch (BusTiming
) {
1122 if (PreferredClockFreq
!= EDKII_SD_MMC_CLOCK_FREQ_IGNORE
&& PreferredClockFreq
< MaxClockFreq
) {
1123 return PreferredClockFreq
;
1125 return MaxClockFreq
;
1130 Get the driver strength to be set on bus.
1132 @param[in] Private Pointer to controller private data
1133 @param[in] SlotIndex Index of the slot in the controller
1134 @param[in] ExtCsd Pointer to card's extended CSD
1135 @param[in] BusTiming Bus timing set on the bus
1137 @return Value of the driver strength to be set on the bus
1139 EDKII_SD_MMC_DRIVER_STRENGTH
1140 EmmcGetTargetDriverStrength (
1141 IN SD_MMC_HC_PRIVATE_DATA
*Private
,
1143 IN EMMC_EXT_CSD
*ExtCsd
,
1144 IN SD_MMC_BUS_MODE BusTiming
1147 EDKII_SD_MMC_DRIVER_STRENGTH PreferredDriverStrength
;
1148 EDKII_SD_MMC_DRIVER_STRENGTH DriverStrength
;
1150 PreferredDriverStrength
= Private
->Slot
[SlotIndex
].OperatingParameters
.DriverStrength
;
1151 DriverStrength
.Emmc
= EmmcDriverStrengthType0
;
1153 if (PreferredDriverStrength
.Emmc
!= EDKII_SD_MMC_DRIVER_STRENGTH_IGNORE
&&
1154 (ExtCsd
->DriverStrength
& (BIT0
<< PreferredDriverStrength
.Emmc
))) {
1155 DriverStrength
.Emmc
= PreferredDriverStrength
.Emmc
;
1158 return DriverStrength
;
1162 Get the target settings for the bus mode.
1164 @param[in] Private Pointer to controller private data
1165 @param[in] SlotIndex Index of the slot in the controller
1166 @param[in] ExtCsd Pointer to card's extended CSD
1167 @param[out] BusMode Target configuration of the bus
1170 EmmcGetTargetBusMode (
1171 IN SD_MMC_HC_PRIVATE_DATA
*Private
,
1173 IN EMMC_EXT_CSD
*ExtCsd
,
1174 OUT SD_MMC_BUS_SETTINGS
*BusMode
1177 BusMode
->BusTiming
= EmmcGetTargetBusTiming (Private
, SlotIndex
, ExtCsd
);
1178 BusMode
->BusWidth
= EmmcGetTargetBusWidth (Private
, SlotIndex
, ExtCsd
, BusMode
->BusTiming
);
1179 BusMode
->ClockFreq
= EmmcGetTargetClockFreq (Private
, SlotIndex
, ExtCsd
, BusMode
->BusTiming
);
1180 BusMode
->DriverStrength
= EmmcGetTargetDriverStrength (Private
, SlotIndex
, ExtCsd
, BusMode
->BusTiming
);
1184 Switch the high speed timing according to request.
1186 Refer to EMMC Electrical Standard Spec 5.1 Section 6.6.8 and SD Host Controller
1187 Simplified Spec 3.0 Figure 2-29 for details.
1189 @param[in] PciIo A pointer to the EFI_PCI_IO_PROTOCOL instance.
1190 @param[in] PassThru A pointer to the EFI_SD_MMC_PASS_THRU_PROTOCOL instance.
1191 @param[in] Slot The slot number of the SD card to send the command to.
1192 @param[in] Rca The relative device address to be assigned.
1194 @retval EFI_SUCCESS The operation is done correctly.
1195 @retval Others The operation fails.
1200 IN EFI_PCI_IO_PROTOCOL
*PciIo
,
1201 IN EFI_SD_MMC_PASS_THRU_PROTOCOL
*PassThru
,
1208 EMMC_EXT_CSD ExtCsd
;
1209 SD_MMC_BUS_SETTINGS BusMode
;
1210 SD_MMC_HC_PRIVATE_DATA
*Private
;
1212 Private
= SD_MMC_HC_PRIVATE_FROM_THIS (PassThru
);
1214 Status
= EmmcGetCsd (PassThru
, Slot
, Rca
, &Csd
);
1215 if (EFI_ERROR (Status
)) {
1216 DEBUG ((DEBUG_ERROR
, "EmmcSetBusMode: GetCsd fails with %r\n", Status
));
1220 Status
= EmmcSelect (PassThru
, Slot
, Rca
);
1221 if (EFI_ERROR (Status
)) {
1222 DEBUG ((DEBUG_ERROR
, "EmmcSetBusMode: Select fails with %r\n", Status
));
1226 ASSERT (Private
->BaseClkFreq
[Slot
] != 0);
1229 // Get Device_Type from EXT_CSD register.
1231 Status
= EmmcGetExtCsd (PassThru
, Slot
, &ExtCsd
);
1232 if (EFI_ERROR (Status
)) {
1233 DEBUG ((DEBUG_ERROR
, "EmmcSetBusMode: GetExtCsd fails with %r\n", Status
));
1237 EmmcGetTargetBusMode (Private
, Slot
, &ExtCsd
, &BusMode
);
1239 DEBUG ((DEBUG_INFO
, "EmmcSetBusMode: Target bus mode: timing = %d, width = %d, clock freq = %d, driver strength = %d\n",
1240 BusMode
.BusTiming
, BusMode
.BusWidth
, BusMode
.ClockFreq
, BusMode
.DriverStrength
.Emmc
));
1242 if (BusMode
.BusTiming
== SdMmcMmcHs400
) {
1243 Status
= EmmcSwitchToHS400 (PciIo
, PassThru
, Slot
, Rca
, &BusMode
);
1244 } else if (BusMode
.BusTiming
== SdMmcMmcHs200
) {
1245 Status
= EmmcSwitchToHS200 (PciIo
, PassThru
, Slot
, Rca
, &BusMode
);
1247 Status
= EmmcSwitchToHighSpeed (PciIo
, PassThru
, Slot
, Rca
, &BusMode
);
1250 DEBUG ((DEBUG_INFO
, "EmmcSetBusMode: Switch to %a %r\n", (BusMode
.BusTiming
== SdMmcMmcHs400
) ? "HS400" : ((BusMode
.BusTiming
== SdMmcMmcHs200
) ? "HS200" : "HighSpeed"), Status
));
1256 Execute EMMC device identification procedure.
1258 Refer to EMMC Electrical Standard Spec 5.1 Section 6.4 for details.
1260 @param[in] Private A pointer to the SD_MMC_HC_PRIVATE_DATA instance.
1261 @param[in] Slot The slot number of the SD card to send the command to.
1263 @retval EFI_SUCCESS There is a EMMC card.
1264 @retval Others There is not a EMMC card.
1268 EmmcIdentification (
1269 IN SD_MMC_HC_PRIVATE_DATA
*Private
,
1274 EFI_PCI_IO_PROTOCOL
*PciIo
;
1275 EFI_SD_MMC_PASS_THRU_PROTOCOL
*PassThru
;
1280 PciIo
= Private
->PciIo
;
1281 PassThru
= &Private
->PassThru
;
1283 Status
= EmmcReset (PassThru
, Slot
);
1284 if (EFI_ERROR (Status
)) {
1285 DEBUG ((DEBUG_VERBOSE
, "EmmcIdentification: Executing Cmd0 fails with %r\n", Status
));
1292 Status
= EmmcGetOcr (PassThru
, Slot
, &Ocr
);
1293 if (EFI_ERROR (Status
)) {
1294 DEBUG ((DEBUG_VERBOSE
, "EmmcIdentification: Executing Cmd1 fails with %r\n", Status
));
1299 if (Retry
++ == 100) {
1300 DEBUG ((DEBUG_VERBOSE
, "EmmcIdentification: Executing Cmd1 fails too many times\n"));
1301 return EFI_DEVICE_ERROR
;
1303 gBS
->Stall(10 * 1000);
1304 } while ((Ocr
& BIT31
) == 0);
1306 Status
= EmmcGetAllCid (PassThru
, Slot
);
1307 if (EFI_ERROR (Status
)) {
1308 DEBUG ((DEBUG_VERBOSE
, "EmmcIdentification: Executing Cmd2 fails with %r\n", Status
));
1312 // Slot starts from 0 and valid RCA starts from 1.
1313 // Here we takes a simple formula to calculate the RCA.
1314 // Don't support multiple devices on the slot, that is
1315 // shared bus slot feature.
1318 Status
= EmmcSetRca (PassThru
, Slot
, Rca
);
1319 if (EFI_ERROR (Status
)) {
1320 DEBUG ((DEBUG_ERROR
, "EmmcIdentification: Executing Cmd3 fails with %r\n", Status
));
1324 // Enter Data Tranfer Mode.
1326 DEBUG ((DEBUG_INFO
, "EmmcIdentification: Found a EMMC device at slot [%d], RCA [%d]\n", Slot
, Rca
));
1327 Private
->Slot
[Slot
].CardType
= EmmcCardType
;
1329 Status
= EmmcSetBusMode (PciIo
, PassThru
, Slot
, Rca
);