.ig
Copyright (C) 2002-10 Bruce Allen <smartmontools-support@lists.sourceforge.net>
- $Id: smartctl.8.in 3320 2011-04-30 20:44:55Z chrfranke $
+ $Id: smartctl.8.in 3530 2012-03-27 19:54:06Z chrfranke $
This program is free software; you can redistribute it and/or modify it
under the terms of the GNU General Public License as published by the Free
.SH SYNOPSIS
.B smartctl [options] device
+.\" %IF NOT OS Windows
.SH FULL PATH
.B /usr/local/sbin/smartctl
+.\" %ENDIF NOT OS Windows
.SH PACKAGE VERSION
CURRENT_SVN_VERSION CURRENT_SVN_DATE CURRENT_SVN_REV
.SH DESCRIPTION
+.\" %IF NOT OS ALL
+.\"! [This man page is generated for the OS_MAN_FILTER version of smartmontools.
+.\"! It does not contain info specific to other platforms.]
+.\"! .PP
+.\" %ENDIF NOT OS ALL
\fBsmartctl\fP controls the Self\-Monitoring, Analysis and Reporting
Technology (SMART) system built into many ATA\-3 and later ATA, IDE and
SCSI\-3 hard drives. The purpose of SMART is to monitor the reliability
is often derived from the device path but may need help with the \'\-d\'
option (for more information see the section on "ATA, SCSI command sets
and SAT" below). Device paths are as follows:
+.\" %IF OS Linux
.IP \fBLINUX\fP: 9
Use the forms \fB"/dev/hd[a\-t]"\fP for IDE/ATA devices, and
\fB"/dev/sd[a\-z]"\fP for SCSI devices. For SCSI Tape Drives and
you need \fB"/dev/sg[2\-9]"\fP (note that smartmontools interacts with
the Areca controllers via a SCSI generic device which is different
than the SCSI device used for reading and writing data)!
+.\" %ENDIF OS Linux
+.\" %IF OS Darwin
.IP \fBDARWIN\fP: 9
Use the forms \fB/dev/disk[0\-9]\fP or equivalently \fBdisk[0\-9]\fP or equivalently
\fB/dev/rdisk[0\-9]\fP. Long forms are also available: please use \'\-h\' to see some
examples. Note that there is currently no Darwin SCSI support.
+.\" %ENDIF OS Darwin
+.\" %IF OS FreeBSD
.IP \fBFREEBSD\fP: 9
Use the forms \fB"/dev/ad[0\-9]+"\fP for IDE/ATA
devices and \fB"/dev/da[0\-9]+"\fP or \fB"/dev/pass[0\-9]+"\fP for SCSI devices.
For SATA devices on AHCI bus use \fB"/dev/ada[0\-9]+"\fP format.
+.\" %ENDIF OS FreeBSD
+.\" %IF OS NetBSD OpenBSD
.IP \fBNETBSD/OPENBSD\fP: 9
Use the form \fB"/dev/wd[0\-9]+c"\fP for IDE/ATA
devices. For SCSI disk and tape devices, use the device names
\fB"/dev/sd[0\-9]+c"\fP and \fB"/dev/st[0\-9]+c"\fP respectively.
Be sure to specify the correct "whole disk" partition letter for
your architecture.
+.\" %ENDIF OS NetBSD OpenBSD
+.\" %IF OS Solaris
.IP \fBSOLARIS\fP: 9
Use the forms \fB"/dev/rdsk/c?t?d?s?"\fP for IDE/ATA and SCSI disk
devices, and \fB"/dev/rmt/*"\fP for SCSI tape devices.
+.\" %ENDIF OS Solaris
+.\" %IF OS Windows
.IP \fBWINDOWS\ 9x/ME\fP: 9
Use the forms \fB"/dev/hd[a\-d]"\fP for standard IDE/ATA devices
accessed via SMARTVSD.VXD, and \fB"/dev/hd[e\-h]"\fP for additional devices
accessed via a patched SMARTVSE.VXD (see INSTALL file for details).
Use the form \fB"/dev/scsi[0\-9][0\-f]"\fP for SCSI devices via an aspi dll
on ASPI adapter 0\-9, ID 0\-15. The prefix \fB"/dev/"\fP is optional.
+.\" %ENDIF OS Windows
+.\" %IF OS Windows Cygwin
.IP \fBWINDOWS\ NT4/2000/XP/2003/Vista/Win7/2008\fP: 9
Use the forms \fB"/dev/sd[a\-z]"\fP for IDE/(S)ATA and SCSI disks
"\\\\.\\PhysicalDrive[0\-25]" (where "a" maps to "0").
driver use \fB"/dev/csmi[0\-9],N"\fP where N specifies the port behind
the logical scsi controller "\\\\.\\Scsi[0\-9]:".
The prefix \fB"/dev/"\fP is optional.
+.\" %ENDIF OS Windows Cygwin
+.\" %IF OS Cygwin
.IP \fBCYGWIN\fP: 9
See "WINDOWS NT4/2000/XP/2003/Vista/Win7/2008" above.
+.\" %ENDIF OS Cygwin
+.\" %IF OS OS2
.IP \fBOS/2,eComStation\fP: 9
Use the form \fB"/dev/hd[a\-z]"\fP for IDE/ATA devices.
+.\" %ENDIF OS OS2
.PP
if \'\-\' is specified as the device path, \fBsmartctl\fP reads and
interprets it's own debug output from standard input.
Prints all SMART and non-SMART information about the device. For ATA
devices this is equivalent to
.nf
-\'\-H \-i \-c \-A \-f brief \-l xerror,error \-l xselftest,selftest
+\'\-H \-i \-g all \-c \-A \-f brief \-l xerror,error \-l xselftest,selftest
\-l selective \-l directory \-l scttemp \-l scterc \-l sataphy\'.
.fi
and for SCSI, this is equivalent to
.nf
smartctl --scan-open -- -a -W 4,45,50 -m admin@work > smartd.conf
.fi
+.TP
+.B \-g NAME, \-\-get=NAME
+Get non\-SMART device settings. See \'\-s, \-\-set\' below for further info.
.TP
.B RUN\-TIME BEHAVIOR OPTIONS:
\fBsmartctl\fP
from issuing SCSI commands to an ATA device.
+.\" %IF NOT OS Darwin
.I scsi
\- the device type is SCSI. This prevents
\fBsmartctl\fP
from issuing ATA commands to a SCSI device.
-.I sat
+.I sat[,auto][,N]
\- the device type is SCSI to ATA Translation (SAT).
This is for ATA disks that have a SCSI to ATA Translation (SAT) Layer
(SATL) between the disk and the operating system.
the other 16 bytes long. The default is the 16 byte variant which can be
overridden with either \'\-d sat,12\' or \'\-d sat,16\'.
+If \'-d sat,auto\' is specified, device type SAT (for ATA/SATA disks) is
+only used if the SCSI INQUIRY data reports a SATL (VENDOR: "ATA ").
+Otherwise device type SCSI (for SCSI/SAS disks) is used.
+
.I usbcypress
\- this device type is for ATA disks that are behind a Cypress USB to PATA
bridge. This will use the ATACB proprietary scsi pass through command.
\- this device type is for SATA disks that are behind a SunplusIT USB to SATA
bridge.
+.\" %ENDIF NOT OS Darwin
+.\" %IF OS Linux
.I marvell
\- [Linux only] interact with SATA disks behind Marvell chip-set
controllers (using the Marvell rather than libata driver).
.fi
For PERC5/6 controllers: \fB/dev/megaraid_sas_ioctl_node\fP
+.\" %ENDIF OS Linux
+.\" %IF OS FreeBSD Linux
.I 3ware,N
\- [FreeBSD and Linux only] the device consists of one or more ATA disks
connected to a 3ware RAID controller. The non-negative integer N
The necessary WRITE LOG commands can not be passed through the SCSI
interface.
+.\" %ENDIF OS FreeBSD Linux
+.\" %IF OS Linux FreeBSD
.I areca,N
-\- [Linux only] the device consists of one or more SATA disks connected to an
+\- [Linux and FreeBSD only] the device consists of one or more SATA disks connected to an
Areca SATA RAID controller. The positive integer N (in the range from 1 to
24 inclusive) denotes which disk on the controller is monitored.
-Use syntax such as:
+.\" %ENDIF OS Linux FreeBSD
+.\" %IF OS Linux
+On Linux use syntax such as:
.nf
\fBsmartctl \-a \-d areca,2 /dev/sg2\fP
.fi
.nf
\fBsmartctl \-a \-d areca,3 /dev/sg3\fP
.fi
+.\" %ENDIF OS Linux
+.\" %IF OS FreeBSD
+On FreeBSD use syntax such as:
+.nf
+\fBsmartctl \-a \-d areca,2 /dev/arcmsr1\fP
+.fi
+.nf
+\fBsmartctl \-a \-d areca,3 /dev/arcmsr2\fP
+.fi
+.\" %ENDIF OS FreeBSD
The first line above addresses the second disk on the first Areca RAID controller.
The second line addresses the third disk on the second Areca RAID
-controller. To help identify the correct device, use the command:
+controller.
+.\" %IF OS Linux
+To help identify the correct device on Linus, use the command:
.nf
\fBcat /proc/scsi/sg/device_hdr /proc/scsi/sg/devices\fP
.fi
smartmontools are the ones with the type field equal to 3. If the
incorrect device is addressed, please read the warning/error messages
carefully. They should provide hints about what devices to use.
+.\" %ENDIF OS Linux
+.\" %IF OS Linux FreeBSD
Important: the Areca controller must have firmware version 1.46 or
later. Lower-numbered firmware versions will give (harmless) SCSI
error messages and no SMART information.
+.\" %ENDIF OS Linux FreeBSD
+.\" %IF OS FreeBSD Linux
.I cciss,N
\- [FreeBSD and Linux only] the device consists of one or more SCSI/SAS disks
connected to a cciss RAID controller. The non-negative integer N (in the range
connected to a HighPoint RocketRAID controller. The integer L is the
controller id, the integer M is the channel number, and the integer N
is the PMPort number if it is available. The allowed values of L are
-from 1 to 4 inclusive, M are from 1 to 8 inclusive and N from 1 to 4
+from 1 to 4 inclusive, M are from 1 to 16 inclusive and N from 1 to 4
if PMPort available. And also these values are limited by the model
of the HighPoint RocketRAID controller.
Use syntax such as:
+.\" %ENDIF OS FreeBSD Linux
+.\" %IF OS Linux
.nf
\fBsmartctl \-a \-d hpt,1/3 /dev/sda\fP (under Linux)
.fi
.nf
\fBsmartctl \-a \-d hpt,1/2/3 /dev/sda\fP (under Linux)
.fi
+.\" %ENDIF OS Linux
+.\" %IF OS FreeBSD
.nf
\fBsmartctl \-a \-d hpt,1/3 /dev/hptrr\fP (under FreeBSD)
.fi
.nf
\fBsmartctl \-a \-d hpt,1/2/3 /dev/hptrr\fP (under FreeBSD)
.fi
+.\" %ENDIF OS FreeBSD
+.\" %IF OS FreeBSD Linux
Note that the /dev/sda\-z form should be the device node which stands for
the disks derived from the HighPoint RocketRAID controllers under Linux and
under FreeBSD, it is the character device which the driver registered (eg,
/dev/hptrr, /dev/hptmv6).
+.\" %ENDIF OS FreeBSD Linux
.TP
.B \-T TYPE, \-\-tolerance=TYPE
[ATA only] Specifies how tolerant \fBsmartctl\fP should be of ATA and SMART
saving counters to non\-volatile storage. For extreme streaming\-video
type applications you might consider using \fIoff\fP to set the GLTSD
bit.
+.TP
+.B \-g NAME, \-\-get=NAME, \-s NAME[,VALUE], \-\-set=NAME[,VALUE]
+[NEW EXPERIMENTAL SMARTCTL FEATURE] Gets/sets non\-SMART device settings.
+Note that the \'\-\-set\' option shares its short option \'\-s\' with
+\'\-\-smart\'. Valid arguments are:
+
+.I all
+\- Gets all values. This is equivalent to
+.nf
+\'-g aam -g apm -g lookahead -g security -g wcache\'
+.fi
+
+.I aam[,N|off]
+\- [ATA only] Gets/sets the Automatic Acoustic Management (AAM) feature
+(if supported). A value of 128 sets the most quiet (slowest) mode and 254
+the fastest (loudest) mode, \'off\' disables AAM. Devices may support
+intermediate levels. Values below 128 are defined as vendor specific (0)
+or retired (1\-127). Note that the AAM feature was declared obsolete in
+ATA ACS-2 Revision 4a (Dec 2010).
+
+.I apm[,N|off]
+\- [ATA only] Gets/sets the Advanced Power Management (APM) feature on
+device (if supported). If a value between 1 and 254 is provided, it will
+attempt to enable APM and set the specified value, \'off\' disables APM.
+Note the actual behavior depends on the drive, for example some drives disable
+APM if their value is set above 128. Values below 128 are supposed to allow
+drive spindown, values 128 and above adjust only head-parking frequency,
+although the actual behavior defined is also vendor-specific.
+
+.I lookahead[,on|off]
+\- [ATA only] Gets/sets the read look-ahead feature (if supported).
+Read look-ahead is usually enabled by default.
+
+.I security
+\- [ATA only] Gets the status of ATA Security feature (if supported).
+If ATA Security is enabled an ATA user password is set. The drive will be
+locked on next reset then.
+
+.I security-freeze
+\- [ATA only] Sets ATA Security feature to frozen mode. This prevents that
+the drive accepts any security commands until next reset. Note that the
+frozen mode may already be set by BIOS or OS.
+
+.I standby,[N|off]
+\- [ATA only] Sets the standby (spindown) timer and places the drive in the
+IDLE mode. A value of 0 or \'off\' disables the standby timer.
+Values from 1 to 240 specify timeouts from 5 seconds to 20 minutes in 5
+second increments. Values from 241 to 251 specify timeouts from 30 minutes
+to 330 minutes in 30 minute increments. Value 252 specifies 21 minutes.
+Value 253 specifies a vendor specific time between 8 and 12 hours. Value
+255 specifies 21 minutes and 15 seconds. Some drives may use a vendor
+specific interpretation for the values. Note that there is no get option
+because ATA standards do not specify a method to read the standby timer.
+
+.I standby,now
+\- [ATA only] Places the drive in the STANDBY mode. This usually spins down
+the drive. The setting of the standby timer is not affected.
+
+.I wcache[,on|off]
+\- [ATA only] Gets/sets the volatile write cache feature (if supported).
+The write cache is usually enabled by default.
.TP
.B SMART READ AND DISPLAY DATA OPTIONS:
relatively free format (compared with ATA disk attributes).
.TP
.B \-f FORMAT, \-\-format=FORMAT
-[ATA only] Selects the output format of the attributes to one of:
+[ATA only] Selects the output format of the attributes:
.I old
\- Old smartctl format. This is the default unless the \'\-x\' option is
\- New format which fits into 80 colums (except in some rare cases).
This format also decodes four additional attribute flags.
This is the default if the '\-x\' option is specified.
+
+.I hex,id
+\- Print all attribute IDs as hexadecimal numbers.
+
+.I hex,val
+\- Print all normalized values as hexadecimal numbers.
+
+.I hex
+\- Same as \'\-f hex,id \-f hex,val\'.
.TP
.B \-l TYPE, \-\-log=TYPE
Prints either the SMART Error Log, the SMART Self\-Test Log, the SMART
temperature limits and the temperature history table returned by
the SCT Data Table command, and \'scttemp\' prints both.
The temperature values are preserved across power cycles.
-The default temperature logging interval is 1 minute and can be
-configured with the \'\-t scttempint,N[,p]\' option, see below.
-The SCT commands are specified in the proposed ATA\-8 Command Set
-(ACS), and are already implemented in some recent ATA\-7 disks.
+The logging interval can be configured with the
+\'\-l scttempint,N[,p]\' option, see below.
+The SCT commands were introduced in ATA\-8 ACS and were also
+supported by in many ATA\-7 disks.
+
+.I scttempint,N[,p]
+\- [ATA only] clears the SCT temperature history table and sets the
+time interval for temperature logging to N minutes.
+If \',p\' is specified, the setting is preserved across power cycles.
+Otherwise, the setting is volatile and will be reverted to the last
+non-volatile setting by the next hard reset. The default interval
+is vendor specific, typical values are 1, 2, or 5 minutes.
.I scterc[,READTIME,WRITETIME]
+\- [ATA only] prints values and descriptions of the SCT Error Recovery
+Control settings. These are equivalent to TLER (as used by Western
+Digital), CCTL (as used by Samsung and Hitachi) and ERC (as used by
+Seagate). READTIME and WRITETIME arguments (deciseconds) set the
+specified values. Values of 0 disable the feature, other values less
+than 65 are probably not supported. For RAID configurations, this is
+typically set to 70,70 deciseconds.
+
+.I devstat[,PAGE]
\- [ATA only] [NEW EXPERIMENTAL SMARTCTL FEATURE] prints values
-and descriptions of the SCT Error Recovery Control settings. These
-are equivalent to TLER (as used by Western Digital), CCTL (as used
-by Samsung and Hitachi) and ERC (as used by Seagate). READTIME and
-WRITETIME arguments (deciseconds) set the specified values. Values of 0
-disable the feature, other values less than 65 are probably not
-supported. For RAID configurations, this is typically set to
-70,70 deciseconds.
+and descriptions of the ATA Device Statistics log pages
+(General Purpose Log address 0x04). If no PAGE number is specified,
+entries from all supported pages are printed. If PAGE 0 is specified,
+the list of supported pages is printed. Device Statistics was
+introduced in ATA\-8 ACS and is only supported by some recent devices
+(e.g. Intel 320 and 710 Series SSDs).
.I sataphy[,reset]
\- [SATA only] prints values and descriptions of the SATA Phy Event
.fi
writes a binary representation of the one sector log 0x11
(SATA Phy Event Counters) to file log.bin.
+
+.I ssd
+\- [ATA] prints the Solid State Device Statistics log page.
+This has the same effect as \'\-l devstat,7\', see above.
+
+.I ssd
+\- [SCSI] prints the Solid State Media percentage used endurance
+indicator. A value of 0 indicates as new condition while 100
+indicates the device is at the end of its lifetime as projected by the
+manufacturer. The value may reach 255.
.TP
.B \-v ID,FORMAT[:BYTEORDER][,NAME], \-\-vendorattribute=ID,FORMAT[:BYTEORDER][,NAME]
[ATA only] Sets a vendor\-specific raw value print FORMAT, an optional
attribute 5 with big endian instead of little endian
byte ordering.
-The NAME is a string of letters, digits and underscore.
+The NAME is a string of letters, digits and underscore. Its length should
+not exceed 23 characters. The \'\-P showall\' option reports an error if
+this is the case.
.I \-v help
\- Prints (to STDOUT) a list of all valid arguments to this option,
\- Print the Raw value as a 12 digit hexadecimal number.
This may be useful for decoding the meaning of the Raw value.
+.I raw56
+\- Print the Raw value as a 54\-bit unsigned base\-10 integer.
+This includes the reserved byte which follows the 48\-bit raw value.
+
+.I hex56
+\- Print the Raw value as a 14 digit hexadecimal number.
+This includes the reserved byte which follows the 48\-bit raw value.
+
.I raw64
\- Print the Raw value as a 64\-bit unsigned base\-10 integer.
This includes two bytes from the normalized and worst attribute value.
-This new raw format is used by some recent SSD devices.
+This raw format is used by some SSD devices with Indilinx controller.
.I hex64
\- Print the Raw value as a 16 digit hexadecimal number.
This includes two bytes from the normalized and worst attribute value.
-This new raw format is used by some recent SSD devices.
+This raw format is used by some SSD devices with Indilinx controller.
.I min2hour
\- Raw Attribute is power\-on time in minutes. Its raw value
and an optional "Average" 16-bit value if the word is nonzero.
This is the default for Attribute 3.
+.I raw24(raw8)
+\- Print the raw attribute as a 24\-bit value and three optional
+8\-bit values if these bytes are nonzero. This is the default
+for Attribute 9.
+
.I raw24/raw24
\- Raw Attribute contains two 24\-bit values. The first is the
number of load cycles. The second is the number of unload cycles.
.I showall
\- list all recognized drives, and the presets that are set for them,
-then exit.
+then exit. This also checks the drive database regular expressions
+and settings for syntax errors.
The \'\-P showall\' option takes up to two optional arguments to
match a specific drive type and firmware version. The command:
the built in database by default. If \'+\' is specified, then the new
entries prepend the built in entries.
-If this option is not specified, optional entries are read from the file
-\fB/usr/local/etc/smart_drivedb.h\fP (Windows: \fBEXEDIR/drivedb-add.h\fP).
-.\" BEGIN ENABLE_DRIVEDB
-If \fB/usr/local/share/smartmontools/drivedb.h\fP
-(Windows: \fBEXEDIR/drivedb.h\fP) is present, the
-contents of this file is used instead of the built in table.
-
-Run the script \fB/usr/local/sbin/update-smart-drivedb\fP to update this
-file from the smartmontools SVN repository.
-.\" END ENABLE_DRIVEDB
+Optional entries are read from the file
+.\" %IF NOT OS Windows
+\fB/usr/local/etc/smart_drivedb.h\fP
+.\" %ENDIF NOT OS Windows
+.\" %IF OS ALL
+ (Windows: \fBEXEDIR/drivedb-add.h\fP)
+.\" %ENDIF OS ALL
+.\" %IF OS Windows
+.\"! \fBEXEDIR/drivedb-add.h\fP.
+.\" %ENDIF OS Windows
+.\" %IF ENABLE_DRIVEDB
+if this option is not specified.
+
+If
+.\" %IF NOT OS Windows
+\fB/usr/local/share/smartmontools/drivedb.h\fP
+.\" %ENDIF NOT OS Windows
+.\" %IF OS ALL
+(Windows: \fBEXEDIR/drivedb.h\fP)
+.\" %ENDIF OS ALL
+.\" %IF OS Windows
+.\"! \fBEXEDIR/drivedb.h\fP
+.\" %ENDIF OS Windows
+is present, the contents of this file is used instead of the built in table.
+
+Run
+.\" %IF NOT OS Windows
+\fB/usr/local/sbin/update-smart-drivedb\fP
+.\" %ENDIF NOT OS Windows
+.\" %IF OS ALL
+(Windows: \fBEXEDIR/update-smart-drivedb.exe\fP)
+.\" %ENDIF OS ALL
+.\" %IF OS Windows
+.\"! \fBEXEDIR/update-smart-drivedb.exe\fP
+.\" %ENDIF OS Windows
+to update this file from the smartmontools SVN repository.
+.\" %ENDIF ENABLE_DRIVEDB
The database files use the same C/C++ syntax that is used to initialize
the built in database array. C/C++ style comments are allowed.
options above. The value of this option is preserved between selective
self\-tests.
-.I scttempint,N[,p]
-\- [ATA only] set the time interval for SCT temperature logging to N
-minutes. If \',p\' is specified, the setting is preserved across power
-cycles. Otherwise, the setting is volatile and will be reverted to
-default (1 minute), or last non-volatile setting by the next hard reset.
-This command also clears the temperature history table. See
-\'\-l scttemp\' above for more information about SCT temperature logging.
-
.I vendor,N
\- [ATA only] issues the ATA command SMART EXECUTE OFF-LINE IMMEDIATE
with subcommand N in LBA LOW register. The subcommand is specified as
related SMART attributes (226, 227, 228). Note that the raw values of
these attributes are held at 65535 (0xffff) until the workload timer
reaches 60 minutes.
+
+.I force
+\- [ATA only] start new self\-test even if another test is already running.
+By default a running self\-test will not be interrupted to begin another
+test.
+
+.I scttempint,N[,p]
+\- is no longer supported, use \'\-l scttempint,N[,p]\' instead, see above.
.TP
.B \-C, \-\-captive
[ATA] Runs self\-tests in captive mode. This has no effect with \'\-t
or device is in a low-power mode (see \'\-n\' option above).
.TP
.B Bit 2:
-Some SMART command to the disk failed, or there was a checksum error
-in a SMART data structure (see \'\-b\' option above).
+Some SMART or other ATA command to the disk failed, or there was a checksum
+error in a SMART data structure (see \'\-b\' option above).
.TP
.B Bit 3:
SMART status check returned "DISK FAILING".
The device self\-test log contains records of errors.
[ATA only] Failed self-tests outdated by a newer successful extended
self\-test are ignored.
-
+.PP
To test within the shell for whether or not the different bits are
turned on or off, you can use the following type of construction (this
is bash syntax):
$smartstat will be nonzero if SMART status check returned "disk
failing" and zero otherwise.
+This bash script prints all status bits:
+.nf
+status=$?
+for ((i=0; i<8; i++)); do
+ echo "Bit $i: $((status & 2**i && 1))"
+done
+.fi
+
.PP
.SH NOTES
The TapeAlert log page flags are cleared for the initiator when the
\fBGuido Guenther\fP (Autoconf/Automake packaging)
\fBGeoffrey Keating\fP (Darwin ATA interface)
\fBEduard Martinescu\fP (FreeBSD interface)
-\fBFr\*'ed\*'eric L. W. Meunier\fP (Web site and Mailing list)
+\fBFr\['e]d\['e]ric L. W. Meunier\fP (Web site and Mailing list)
\fBGabriele Pohl\fP (Web site and Wiki, conversion from CVS to SVN)
\fBKeiji Sawada\fP (Solaris ATA interface)
\fBManfred Schwarb\fP (Drive database)
volume of the \'AT Attachment with Packet Interface\-7\' (ATA/ATAPI\-7)
specification Revision 4b. This documents the SMART functionality which the
\fBsmartmontools\fP utilities provide access to.
-This and other versions of this Specification are available from
-the T13 web site \fBhttp://www.t13.org/\fP .
.fi
The functioning of SMART was originally defined by the SFF\-8035i
.SH
SVN ID OF THIS PAGE:
-$Id: smartctl.8.in 3320 2011-04-30 20:44:55Z chrfranke $
+$Id: smartctl.8.in 3530 2012-03-27 19:54:06Z chrfranke $
projects / mirror_smartmontools-debian.git / blobdiff