All mapping iterator logic is based on the assumption that sg->offset
is always lower than PAGE_SIZE.
But there are situations where sg->offset is such that the SG item
is on the second page. In that case sg_copy_to_buffer() fails
properly copying the data into the buffer. One of the reason is
that the data will be outside the kmapped area used to access that
data.
This patch fixes the issue by adjusting the mapping iterator
offset and pgoffset fields such that offset is always lower than
PAGE_SIZE.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr> Fixes: 4225fc8555a9 ("lib/scatterlist: use page iterator in the mapping iterator") Cc: stable@vger.kernel.org Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
According to the open() manpage, Linux reserves the access mode 3
to mean "check for read and write permission on the file and return
a file descriptor that can't be used for reading or writing."
Currently, the NFSv4 code will ask the server to open the file,
and will use an incorrect share access mode of 0. Since it has
an incorrect share access mode, the client later forgets to send
a corresponding close, meaning it can leak stateids on the server.
We added code to restock the buffer upon ALIVE interrupt
when MSI-X is disabled. This was added as part of the context
info code. This code was added only if the ISR debug level
is set which is very unlikely to be related.
Move this code to run even when the ISR debug level is not
set.
Note that gen2 devices work with MSI-X in most cases so that
this path is seldom used.
Sometimes the register status can include interrupts that
were masked. We can, for example, get the RF-Kill bit set
in the interrupt status register although this interrupt
was masked. Then if we get the ALIVE interrupt (for example)
that was not masked, we need to *not* service the RF-Kill
interrupt.
Fix this in the MSI-X interrupt handler.
The GPU regulator enable ramp delay for Jetson TX1 is set to 1ms which
not sufficient because the enable ramp delay has been measured to be
greater than 1ms. Furthermore, the downstream kernels released by NVIDIA
for Jetson TX1 are using a enable ramp delay 2ms and a settling delay of
160us. Update the GPU regulator enable ramp delay for Jetson TX1 to be
2ms and add a settling delay of 160us.
On S2MPS11 device, the buck7 and buck8 regulator voltages start at 750
mV, not 600 mV. Using wrong minimal value caused shifting of these
regulator values by 150 mV (e.g. buck7 usually configured to v1.35 V was
reported as 1.2 V).
On most of the boards these regulators are left in default state so this
was only affecting reported voltage. However if any driver wanted to
change them, then effectively it would set voltage 150 mV higher than
intended.
Cc: <stable@vger.kernel.org> Fixes: cb74685ecb39 ("regulator: s2mps11: Add samsung s2mps11 regulator driver") Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In the function alps_is_cs19_trackpoint(), we check if the param[1] is
in the 0x20~0x2f range, but the code we wrote for this checking is not
correct:
(param[1] & 0x20) does not mean param[1] is in the range of 0x20~0x2f,
it also means the param[1] is in the range of 0x30~0x3f, 0x60~0x6f...
Now fix it with a new condition checking ((param[1] & 0xf0) == 0x20).
Adds the Lenovo T580 to the SMBus intertouch list for Synaptics
touchpads. I've tested with this for a week now, and it seems a great
improvement. It's also nice to have the complaint gone from dmesg.
Signed-off-by: Nick Black <dankamongmen@gmail.com> Cc: stable@vger.kernel.org Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
On a latest Lenovo laptop, the trackpoint and 3 buttons below it
don't work at all, when we move the trackpoint or press those 3
buttons, the kernel will print out:
"Rejected trackstick packet from non DualPoint device"
This device is identified as an alps touchpad but the packet has
trackpoint format, so the alps.c drops the packet and prints out
the message above.
According to XiaoXiao's explanation, this device is named cs19 and
is trackpoint-only device, its firmware is only for trackpoint, it
is independent of touchpad and is a device completely different from
DualPoint ones.
To drive this device with mininal changes to the existing driver, we
just let the alps driver not handle this device, then the trackpoint.c
will be the driver of this device if the trackpoint driver is enabled.
(if not, this device will fallback to a bare PS/2 device)
With the trackpoint.c, this trackpoint and 3 buttons all work well,
they have all features that the trackpoint should have, like
scrolling-screen, drag-and-drop and frame-selection.
Signed-off-by: XiaoXiao Liu <sliuuxiaonxiao@gmail.com> Signed-off-by: Hui Wang <hui.wang@canonical.com> Reviewed-by: Pali Rohár <pali.rohar@gmail.com> Cc: stable@vger.kernel.org Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The GTCO tablet input driver configures itself from an HID report sent
via USB during the initial enumeration process. Some debugging messages
are generated during the parsing. A debugging message indentation
counter is not bounds checked, leading to the ability for a specially
crafted HID report to cause '-' and null bytes be written past the end
of the indentation array. As long as the kernel has CONFIG_DYNAMIC_DEBUG
enabled, this code will not be optimized out. This was discovered
during code review after a previous syzkaller bug was found in this
driver.
The AES GCM function reuses an 'op' data structure, which members
contain values that must be cleared for each (re)use.
This fix resolves a crypto self-test failure:
alg: aead: gcm-aes-ccp encryption test failed (wrong result) on test vector 2, cfg="two even aligned splits"
Fixes: 36cf515b9bbe ("crypto: ccp - Enable support for AES GCM on v5 CCPs") Cc: <stable@vger.kernel.org> Signed-off-by: Gary R Hook <gary.hook@amd.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Clear the CRYPTO_TFM_REQ_MAY_SLEEP flag when the chacha20poly1305
operation is being continued from an async completion callback, since
sleeping may not be allowed in that context.
This is basically the same bug that was recently fixed in the xts and
lrw templates. But, it's always been broken in chacha20poly1305 too.
This was found using syzkaller in combination with the updated crypto
self-tests which actually test the MAY_SLEEP flag now.
The sha256-ce finup implementation for ARM64 produces wrong digest
for empty input (len=0). Expected: the actual digest, result: initial
value of SHA internal state. The error is in sha256_ce_finup:
for empty data `finalize` will be 1, so the code is relying on
sha2_ce_transform to make the final round. However, in
sha256_base_do_update, the block function will not be called when
len == 0.
Fix it by setting finalize to 0 if data is empty.
Fixes: 03802f6a80b3a ("crypto: arm64/sha2-ce - move SHA-224/256 ARMv8 implementation to base layer") Cc: stable@vger.kernel.org Signed-off-by: Elena Petrova <lenaptr@google.com> Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The sha1-ce finup implementation for ARM64 produces wrong digest
for empty input (len=0). Expected: da39a3ee..., result: 67452301...
(initial value of SHA internal state). The error is in sha1_ce_finup:
for empty data `finalize` will be 1, so the code is relying on
sha1_ce_transform to make the final round. However, in
sha1_base_do_update, the block function will not be called when
len == 0.
Fix it by setting finalize to 0 if data is empty.
Fixes: 07eb54d306f4 ("crypto: arm64/sha1-ce - move SHA-1 ARMv8 implementation to base layer") Cc: stable@vger.kernel.org Signed-off-by: Elena Petrova <lenaptr@google.com> Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The error code read from the queue status register is only 6 bits wide,
but we need to verify its value is within range before indexing the error
messages.
Fixes: 81422badb3907 ("crypto: ccp - Make syslog errors human-readable") Cc: <stable@vger.kernel.org> Reported-by: Cfir Cohen <cfir@google.com> Signed-off-by: Gary R Hook <gary.hook@amd.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Changing ghash_mod_init() to be subsys_initcall made it start running
before the alignment fault handler has been installed on ARM. In kernel
builds where the keys in the ghash test vectors happened to be
misaligned in the kernel image, this exposed the longstanding bug that
ghash_setkey() is incorrectly casting the key buffer (which can have any
alignment) to be128 for passing to gf128mul_init_4k_lle().
Fix this by memcpy()ing the key to a temporary buffer.
Don't fix it by setting an alignmask on the algorithm instead because
that would unnecessarily force alignment of the data too.
Fixes: 2cdc6899a88e ("crypto: ghash - Add GHASH digest algorithm for GCM") Reported-by: Peter Robinson <pbrobinson@gmail.com> Cc: stable@vger.kernel.org Signed-off-by: Eric Biggers <ebiggers@google.com> Tested-by: Peter Robinson <pbrobinson@gmail.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
A system bus error during a PDMA transfer can mess up the calculation of
the transfer residual (the PDMA handshaking hardware lacks a byte
counter). This results in data corruption.
The algorithm in this patch anticipates a bus error by starting each
transfer with a MOVE.B instruction. If a bus error is caught the transfer
will be retried. If a bus error is caught later in the transfer (for a
MOVE.W instruction) the transfer gets failed and subsequent requests for
that target will use PIO instead of PDMA.
This avoids the "!REQ and !ACK" error so the severity level of that message
is reduced to KERN_DEBUG.
Cc: Michael Schmitz <schmitzmic@gmail.com> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: stable@vger.kernel.org # v4.14+ Fixes: 3a0f64bfa907 ("mac_scsi: Fix pseudo DMA implementation") Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Reported-by: Chris Jones <chris@martin-jones.com> Tested-by: Stan Johnson <userm57@yahoo.com> Tested-by: Michael Schmitz <schmitzmic@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Some targets introduce delays when handshaking the response to certain
commands. For example, a disk may send a 96-byte response to an INQUIRY
command (or a 24-byte response to a MODE SENSE command) too slowly.
Apparently the first 12 or 14 bytes are handshaked okay but then the system
bus error timeout is reached while transferring the next word.
Since the scsi bus phase hasn't changed, the driver then sets the target
borken flag to prevent further PDMA transfers. The driver also logs the
warning, "switching to slow handshake".
Raise the PDMA threshold to 512 bytes so that PIO transfers will be used
for these commands. This default is sufficiently low that PDMA will still
be used for READ and WRITE commands.
The existing threshold (16 bytes) was chosen more or less at random.
However, best performance requires the threshold to be as low as possible.
Those systems that don't need the PIO workaround at all may benefit from
mac_scsi.setup_use_pdma=1
Cc: Michael Schmitz <schmitzmic@gmail.com> Cc: stable@vger.kernel.org # v4.14+ Fixes: 3a0f64bfa907 ("mac_scsi: Fix pseudo DMA implementation") Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Tested-by: Stan Johnson <userm57@yahoo.com> Tested-by: Michael Schmitz <schmitzmic@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In megasas_get_target_prop(), driver is incorrectly calculating the target
ID for devices with channel 1 and 3. Due to this, firmware will either
fail the command (if there is no device with the target id sent from
driver) or could return the properties for a target which was not
intended. Devices could end up with the wrong queue depth due to this.
Fix target id calculation for channel 1 and 3.
Fixes: 96188a89cc6d ("scsi: megaraid_sas: NVME interface target prop added") Cc: stable@vger.kernel.org Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When scsi_init_sense_cache(host) is called concurrently from different
hosts, each code path may find that no cache has been created and
allocate a new one. The lack of locking can lead to potentially
overriding a cache allocated by a different host.
Fix the issue by moving 'mutex_lock(&scsi_sense_cache_mutex)' before
scsi_select_sense_cache().
Fixes: 0a6ac4ee7c21 ("scsi: respect unchecked_isa_dma for blk-mq") Cc: Stable <stable@vger.kernel.org> Cc: Christoph Hellwig <hch@lst.de> Cc: Hannes Reinecke <hare@suse.com> Cc: Ewan D. Milne <emilne@redhat.com> Signed-off-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The purpose of that commit was to suppress a timeout warning message which
appeared to be caused by target latency. But suppressing the warning is
undesirable as the warning may indicate a messed up transfer count.
Another problem with that commit is that 15 ms is too long to keep
interrupts disabled as interrupt latency can cause system clock drift and
other problems.
Cc: Michael Schmitz <schmitzmic@gmail.com> Cc: stable@vger.kernel.org Fixes: 4822827a69d7 ("scsi: ncr5380: Increase register polling limit") Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Tested-by: Stan Johnson <userm57@yahoo.com> Tested-by: Michael Schmitz <schmitzmic@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The reselection interrupt gets disabled during selection and must be
re-enabled when hostdata->connected becomes NULL. If it isn't re-enabled a
disconnected command may time-out or the target may wedge the bus while
trying to reselect the host. This can happen after a command is aborted.
Fix this by enabling the reselection interrupt in NCR5380_main() after
calls to NCR5380_select() and NCR5380_information_transfer() return.
Cc: Michael Schmitz <schmitzmic@gmail.com> Cc: stable@vger.kernel.org # v4.9+ Fixes: 8b00c3d5d40d ("ncr5380: Implement new eh_abort_handler") Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Tested-by: Stan Johnson <userm57@yahoo.com> Tested-by: Michael Schmitz <schmitzmic@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Replace a 'goto' statement with a simple 'return' where possible. This
improves readability. No functional change.
Tested-by: Michael Schmitz <schmitzmic@gmail.com> Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Instead of trying to allocate pages with GFP_USER in
add_ballooned_pages() check the available free memory via
si_mem_available(). GFP_USER is far less limiting memory exhaustion
than the test via si_mem_available().
This will avoid dom0 running out of memory due to excessive foreign
page mappings especially on ARM and on x86 in PVH mode, as those don't
have a pre-ballooned area which can be used for foreign mappings.
As the normal ballooning suffers from the same problem don't balloon
down more than si_mem_available() pages in one iteration. At the same
time limit the default maximum number of retries.
This fixes the invalid pointer dereference in the drive_name function of
the floppy driver.
The native_format field of the struct floppy_drive_params is used as
floppy_type array index in the drive_name function. Thus, the field
should be checked the same way as the autodetect field.
To trigger the bug, one could use a value out of range and set the drive
parameters with the FDSETDRVPRM ioctl. Next, FDGETDRVTYP ioctl should
be used to call the drive_name. A floppy disk is not required to be
inserted.
CAP_SYS_ADMIN is required to call FDSETDRVPRM.
The patch adds the check for a value of the native_format field to be in
the '0 <= x < ARRAY_SIZE(floppy_type)' range of the floppy_type array
indices.
This fixes a global out-of-bounds read access in the next_valid_format
function of the floppy driver.
The values from autodetect field of the struct floppy_drive_params are
used as indices for the floppy_type array in the next_valid_format
function 'floppy_type[DP->autodetect[probed_format]].sect'.
To trigger the bug, one could use a value out of range and set the drive
parameters with the FDSETDRVPRM ioctl. A floppy disk is not required to
be inserted.
CAP_SYS_ADMIN is required to call FDSETDRVPRM.
The patch adds the check for values of the autodetect field to be in the
'0 <= x < ARRAY_SIZE(floppy_type)' range of the floppy_type array indices.
A recent commit efa14c3985828d ("iavf: allow null RX descriptors") added
a null pointer sanity check on rx_buffer, however, rx_buffer is being
dereferenced before that check, which implies a null pointer dereference
bug can potentially occur. Fix this by only dereferencing rx_buffer
until after the null pointer check.
Addresses-Coverity: ("Dereference before null check") Signed-off-by: Colin Ian King <colin.king@canonical.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Defer probing of the orion-mdio interface when getting a clock returns
EPROBE_DEFER. This avoids locking up the Armada 8k SoC when mdio is used
before all clocks have been enabled.
Signed-off-by: Josua Mayer <josua@solid-run.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Current gtp_newlink() could be called after unregister_pernet_subsys().
gtp_newlink() uses gtp_net but it can be destroyed by
unregister_pernet_subsys().
So unregister_pernet_subsys() should be called after
rtnl_link_unregister().
Test commands:
#SHELL 1
while :
do
for i in {1..5}
do
./gtp-link add gtp$i &
done
killall gtp-link
done
gtp_encap_destroy() is called twice.
1. When interface is deleted.
2. When udp socket is destroyed.
either gtp->sk0 or gtp->sk1u could be freed by sock_put() in
gtp_encap_destroy(). so, when gtp_encap_destroy() is called again,
it would uses freed sk pointer.
patch makes gtp_encap_destroy() to set either gtp->sk0 or gtp->sk1u to
null. in addition, both gtp->sk0 and gtp->sk1u pointer are protected
by rtnl_lock. so, rtnl_lock() is added.
Test command:
gtp-link add gtp1 &
killall gtp-link
ip link del gtp1
Fixes: 1e3a3abd8b28 ("gtp: make GTP sockets in gtp_newlink optional") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
ipv4_pdp_add() is called in RCU read-side critical section.
So GFP_KERNEL should not be used in the function.
This patch make ipv4_pdp_add() to use GFP_ATOMIC instead of GFP_KERNEL.
gtp_encap_enable_socket() and gtp_encap_destroy() are not protected
by rcu_read_lock(). and it's not safe to write sk->sk_user_data.
This patch make these functions to use lock_sock() instead of
rcu_dereference_sk_user_data().
Fixes: 1e3a3abd8b28 ("gtp: make GTP sockets in gtp_newlink optional") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Problem: The Linux Bluetooth stack yields complete control over the BLE
connection interval to the remote device.
The Linux Bluetooth stack provides access to the BLE connection interval
min and max values through /sys/kernel/debug/bluetooth/hci0/
conn_min_interval and /sys/kernel/debug/bluetooth/hci0/conn_max_interval.
These values are used for initial BLE connections, but the remote device
has the ability to request a connection parameter update. In the event
that the remote side requests to change the connection interval, the Linux
kernel currently only validates that the desired value is within the
acceptable range in the Bluetooth specification (6 - 3200, corresponding to
7.5ms - 4000ms). There is currently no validation that the desired value
requested by the remote device is within the min/max limits specified in
the conn_min_interval/conn_max_interval configurations. This essentially
leads to Linux yielding complete control over the connection interval to
the remote device.
The proposed patch adds a verification step to the connection parameter
update mechanism, ensuring that the desired value is within the min/max
bounds of the current connection. If the desired value is outside of the
current connection min/max values, then the connection parameter update
request is rejected and the negative response is returned to the remote
device. Recall that the initial connection is established using the local
conn_min_interval/conn_max_interval values, so this allows the Linux
administrator to retain control over the BLE connection interval.
The one downside that I see is that the current default Linux values for
conn_min_interval and conn_max_interval typically correspond to 30ms and
50ms respectively. If this change were accepted, then it is feasible that
some devices would no longer be able to negotiate to their desired
connection interval values. This might be remedied by setting the default
Linux conn_min_interval and conn_max_interval values to the widest
supported range (6 - 3200 / 7.5ms - 4000ms). This could lead to the same
behavior as the current implementation, where the remote device could
request to change the connection interval value to any value that is
permitted by the Bluetooth specification, and Linux would accept the
desired value.
If an invalid role is sent from user space, gtp_encap_enable() will fail.
Then, it should call gtp_encap_disable_sock() but current code doesn't.
It makes memory leak.
Fixes: 91ed81f9abc7 ("gtp: support SGSN-side tunnels") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Because of both sides doing L2CAP disconnection at the same time, it
was possible to receive L2CAP Disconnection Response with CID that was
already freed. That caused problems if CID was already reused and L2CAP
Connection Request with same CID was sent out. Before this patch kernel
deleted channel context regardless of the state of the channel.
Example where leftover Disconnection Response (frame #402) causes local
device to delete L2CAP channel which was not yet connected. This in
turn confuses remote device's stack because same CID is re-used without
properly disconnecting.
Btmon capture before patch:
** snip **
> ACL Data RX: Handle 43 flags 0x02 dlen 8 #394 [hci1] 10.748949
Channel: 65 len 4 [PSM 3 mode 0] {chan 2}
RFCOMM: Disconnect (DISC) (0x43)
Address: 0x03 cr 1 dlci 0x00
Control: 0x53 poll/final 1
Length: 0
FCS: 0xfd
< ACL Data TX: Handle 43 flags 0x00 dlen 8 #395 [hci1] 10.749062
Channel: 65 len 4 [PSM 3 mode 0] {chan 2}
RFCOMM: Unnumbered Ack (UA) (0x63)
Address: 0x03 cr 1 dlci 0x00
Control: 0x73 poll/final 1
Length: 0
FCS: 0xd7
< ACL Data TX: Handle 43 flags 0x00 dlen 12 #396 [hci1] 10.749073
L2CAP: Disconnection Request (0x06) ident 17 len 4
Destination CID: 65
Source CID: 65
> HCI Event: Number of Completed Packets (0x13) plen 5 #397 [hci1] 10.752391
Num handles: 1
Handle: 43
Count: 1
> HCI Event: Number of Completed Packets (0x13) plen 5 #398 [hci1] 10.753394
Num handles: 1
Handle: 43
Count: 1
> ACL Data RX: Handle 43 flags 0x02 dlen 12 #399 [hci1] 10.756499
L2CAP: Disconnection Request (0x06) ident 26 len 4
Destination CID: 65
Source CID: 65
< ACL Data TX: Handle 43 flags 0x00 dlen 12 #400 [hci1] 10.756548
L2CAP: Disconnection Response (0x07) ident 26 len 4
Destination CID: 65
Source CID: 65
< ACL Data TX: Handle 43 flags 0x00 dlen 12 #401 [hci1] 10.757459
L2CAP: Connection Request (0x02) ident 18 len 4
PSM: 1 (0x0001)
Source CID: 65
> ACL Data RX: Handle 43 flags 0x02 dlen 12 #402 [hci1] 10.759148
L2CAP: Disconnection Response (0x07) ident 17 len 4
Destination CID: 65
Source CID: 65
= bluetoothd: 00:1E:AB:4C:56:54: error updating services: Input/o.. 10.759447
> HCI Event: Number of Completed Packets (0x13) plen 5 #403 [hci1] 10.759386
Num handles: 1
Handle: 43
Count: 1
> ACL Data RX: Handle 43 flags 0x02 dlen 12 #404 [hci1] 10.760397
L2CAP: Connection Request (0x02) ident 27 len 4
PSM: 3 (0x0003)
Source CID: 65
< ACL Data TX: Handle 43 flags 0x00 dlen 16 #405 [hci1] 10.760441
L2CAP: Connection Response (0x03) ident 27 len 8
Destination CID: 65
Source CID: 65
Result: Connection successful (0x0000)
Status: No further information available (0x0000)
< ACL Data TX: Handle 43 flags 0x00 dlen 27 #406 [hci1] 10.760449
L2CAP: Configure Request (0x04) ident 19 len 19
Destination CID: 65
Flags: 0x0000
Option: Maximum Transmission Unit (0x01) [mandatory]
MTU: 1013
Option: Retransmission and Flow Control (0x04) [mandatory]
Mode: Basic (0x00)
TX window size: 0
Max transmit: 0
Retransmission timeout: 0
Monitor timeout: 0
Maximum PDU size: 0
> HCI Event: Number of Completed Packets (0x13) plen 5 #407 [hci1] 10.761399
Num handles: 1
Handle: 43
Count: 1
> ACL Data RX: Handle 43 flags 0x02 dlen 16 #408 [hci1] 10.762942
L2CAP: Connection Response (0x03) ident 18 len 8
Destination CID: 66
Source CID: 65
Result: Connection successful (0x0000)
Status: No further information available (0x0000)
*snip*
Similar case after the patch:
*snip*
> ACL Data RX: Handle 43 flags 0x02 dlen 8 #22702 [hci0] 1664.411056
Channel: 65 len 4 [PSM 3 mode 0] {chan 3}
RFCOMM: Disconnect (DISC) (0x43)
Address: 0x03 cr 1 dlci 0x00
Control: 0x53 poll/final 1
Length: 0
FCS: 0xfd
< ACL Data TX: Handle 43 flags 0x00 dlen 8 #22703 [hci0] 1664.411136
Channel: 65 len 4 [PSM 3 mode 0] {chan 3}
RFCOMM: Unnumbered Ack (UA) (0x63)
Address: 0x03 cr 1 dlci 0x00
Control: 0x73 poll/final 1
Length: 0
FCS: 0xd7
< ACL Data TX: Handle 43 flags 0x00 dlen 12 #22704 [hci0] 1664.411143
L2CAP: Disconnection Request (0x06) ident 11 len 4
Destination CID: 65
Source CID: 65
> HCI Event: Number of Completed Pac.. (0x13) plen 5 #22705 [hci0] 1664.414009
Num handles: 1
Handle: 43
Count: 1
> HCI Event: Number of Completed Pac.. (0x13) plen 5 #22706 [hci0] 1664.415007
Num handles: 1
Handle: 43
Count: 1
> ACL Data RX: Handle 43 flags 0x02 dlen 12 #22707 [hci0] 1664.418674
L2CAP: Disconnection Request (0x06) ident 17 len 4
Destination CID: 65
Source CID: 65
< ACL Data TX: Handle 43 flags 0x00 dlen 12 #22708 [hci0] 1664.418762
L2CAP: Disconnection Response (0x07) ident 17 len 4
Destination CID: 65
Source CID: 65
< ACL Data TX: Handle 43 flags 0x00 dlen 12 #22709 [hci0] 1664.421073
L2CAP: Connection Request (0x02) ident 12 len 4
PSM: 1 (0x0001)
Source CID: 65
> ACL Data RX: Handle 43 flags 0x02 dlen 12 #22710 [hci0] 1664.421371
L2CAP: Disconnection Response (0x07) ident 11 len 4
Destination CID: 65
Source CID: 65
> HCI Event: Number of Completed Pac.. (0x13) plen 5 #22711 [hci0] 1664.424082
Num handles: 1
Handle: 43
Count: 1
> HCI Event: Number of Completed Pac.. (0x13) plen 5 #22712 [hci0] 1664.425040
Num handles: 1
Handle: 43
Count: 1
> ACL Data RX: Handle 43 flags 0x02 dlen 12 #22713 [hci0] 1664.426103
L2CAP: Connection Request (0x02) ident 18 len 4
PSM: 3 (0x0003)
Source CID: 65
< ACL Data TX: Handle 43 flags 0x00 dlen 16 #22714 [hci0] 1664.426186
L2CAP: Connection Response (0x03) ident 18 len 8
Destination CID: 66
Source CID: 65
Result: Connection successful (0x0000)
Status: No further information available (0x0000)
< ACL Data TX: Handle 43 flags 0x00 dlen 27 #22715 [hci0] 1664.426196
L2CAP: Configure Request (0x04) ident 13 len 19
Destination CID: 65
Flags: 0x0000
Option: Maximum Transmission Unit (0x01) [mandatory]
MTU: 1013
Option: Retransmission and Flow Control (0x04) [mandatory]
Mode: Basic (0x00)
TX window size: 0
Max transmit: 0
Retransmission timeout: 0
Monitor timeout: 0
Maximum PDU size: 0
> ACL Data RX: Handle 43 flags 0x02 dlen 16 #22716 [hci0] 1664.428804
L2CAP: Connection Response (0x03) ident 12 len 8
Destination CID: 66
Source CID: 65
Result: Connection successful (0x0000)
Status: No further information available (0x0000)
*snip*
Fix is to check that channel is in state BT_DISCONN before deleting the
channel.
This bug was found while fuzzing Bluez's OBEX implementation using
Synopsys Defensics.
Reported-by: Matti Kamunen <matti.kamunen@synopsys.com> Reported-by: Ari Timonen <ari.timonen@synopsys.com> Signed-off-by: Matias Karhumaa <matias.karhumaa@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Handle overlooked case where the target address is assigned to a peer
and neither route nor gateway exist.
For one peer, no checks are performed to see if it is meant to receive
packets for a given address.
As soon as there is a second peer however, checks are performed
to deal with routes and gateways for handling complex setups with
multiple hops to a target address.
This logic assumed that no route and no gateway imply that the
destination address can not be reached, which is false in case of a
direct peer.
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com> Tested-by: Michael Scott <mike@foundries.io> Signed-off-by: Josua Mayer <josua.mayer@jm0.eu> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Commit 372e722ea4dd4ca1 ("gpiolib: use descriptors internally") renamed
the functions to use a "gpiod" prefix, and commit 79a9becda8940deb
("gpiolib: export descriptor-based GPIO interface") introduced the "raw"
variants, but both changes forgot to update the comments.
Readd a similar reference to gpiod_set_value(), which was accidentally
removed by commit 1e77fc82110ac36f ("gpio: Add missing open drain/source
handling to gpiod_set_value_cansleep()").
After setting up metric groups through the event parser, the metricgroup
code looks them up again in the event list.
Make sure we only look up events that haven't been used by some other
metric. The data structures currently cannot handle more than one metric
per event. This avoids problems with multiple events partially
overlapping.
Signed-off-by: Andi Kleen <ak@linux.intel.com> Acked-by: Jiri Olsa <jolsa@kernel.org> Cc: Kan Liang <kan.liang@linux.intel.com> Link: http://lkml.kernel.org/r/20190624193711.35241-2-andi@firstfloor.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In some buggy scenarios we could possible attempt to transmit frames larger
than maximum MSDU size. Since our devices don't know how to handle this,
it may result in asserts, hangs etc.
This can happen, for example, when we receive a large multicast frame
and try to transmit it back to the air in AP mode.
Since in a legal scenario this should never happen, drop such frames and
warn about it.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The workqueue need to flush and destory while remove sdio module,
otherwise it will have thread which is not destory after remove
sdio modules.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When hdev->tx_sch_mode is HCLGE_FLAG_VNET_BASE_SCH_MODE, the
hclge_tm_schd_mode_vnet_base_cfg calls hclge_tm_pri_schd_mode_cfg
with vport->vport_id as pri_id, which is used as index for
hdev->tm_info.tc_info, it will cause out of bound access issue
if vport_id is equal to or larger than HNAE3_MAX_TC.
Also hardware only support maximum speed of HCLGE_ETHER_MAX_RATE.
So this patch adds two checks for above cases.
Fixes: 848440544b41 ("net: hns3: Add support of TX Scheduler & Shaper to HNS3 driver") Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When system memory is in heavy pressure, bch_gc_thread_start() from
run_cache_set() may fail due to out of memory. In such condition,
c->gc_thread is assigned to -ENOMEM, not NULL pointer. Then in following
failure code path bch_cache_set_error(), when cache_set_flush() gets
called, the code piece to stop c->gc_thread is broken,
if (!IS_ERR_OR_NULL(c->gc_thread))
kthread_stop(c->gc_thread);
And KASAN catches such NULL pointer deference problem, with the warning
information:
[ 561.207881] ==================================================================
[ 561.207900] BUG: KASAN: null-ptr-deref in kthread_stop+0x3b/0x440
[ 561.207904] Write of size 4 at addr 000000000000001c by task kworker/15:1/313
Commit 9da21b1509d8 ("EDAC: Poll timeout cannot be zero, p2") assumes
edac_mc_poll_msec to be unsigned long, but the type of the variable still
remained as int. Setting edac_mc_poll_msec can trigger out-of-bounds
write.
The buggy address belongs to the variable:
edac_mc_poll_msec+0x0/0x40
Memory state around the buggy address: ffffffffb91b2c00: 00 00 00 00 fa fa fa fa 00 00 00 00 fa fa fa fa ffffffffb91b2c80: 00 00 00 00 fa fa fa fa 00 00 00 00 fa fa fa fa
>ffffffffb91b2d00: 04 fa fa fa fa fa fa fa 04 fa fa fa fa fa fa fa
^ ffffffffb91b2d80: 04 fa fa fa fa fa fa fa 00 00 00 00 00 00 00 00 ffffffffb91b2e00: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Fix it by changing the type of edac_mc_poll_msec to unsigned int.
The reason why this patch adopts unsigned int rather than unsigned long
is msecs_to_jiffies() assumes arg to be unsigned int. We can avoid
integer conversion bugs and unsigned int will be large enough for
edac_mc_poll_msec.
Reviewed-by: James Morse <james.morse@arm.com> Fixes: 9da21b1509d8 ("EDAC: Poll timeout cannot be zero, p2") Signed-off-by: Eiichi Tsukata <devel@etsukata.com> Signed-off-by: Tony Luck <tony.luck@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Build testing with some core crypto options disabled revealed
a few modules that are missing CRYPTO_HASH:
crypto/asymmetric_keys/x509_public_key.o: In function `x509_get_sig_params':
x509_public_key.c:(.text+0x4c7): undefined reference to `crypto_alloc_shash'
x509_public_key.c:(.text+0x5e5): undefined reference to `crypto_shash_digest'
crypto/asymmetric_keys/pkcs7_verify.o: In function `pkcs7_digest.isra.0':
pkcs7_verify.c:(.text+0xab): undefined reference to `crypto_alloc_shash'
pkcs7_verify.c:(.text+0x1b2): undefined reference to `crypto_shash_digest'
pkcs7_verify.c:(.text+0x3c1): undefined reference to `crypto_shash_update'
pkcs7_verify.c:(.text+0x411): undefined reference to `crypto_shash_finup'
This normally doesn't show up in randconfig tests because there is
a large number of other options that select CRYPTO_HASH.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Some transceivers may comply with SFF-8472 but not implement the Digital
Diagnostic Monitoring (DDM) interface described in it. The existence of
such area is specified by bit 6 of byte 92, set to 1 if implemented.
Currently, due to not checking this bit ixgbe fails trying to read SFP
module's eeprom with the follow message:
ethtool -m enP51p1s0f0
Cannot get Module EEPROM data: Input/output error
Because it fails to read the additional 256 bytes in which it was assumed
to exist the DDM data.
This issue was noticed using a Mellanox Passive DAC PN 01FT738. The eeprom
data was confirmed by Mellanox as correct and present in other Passive
DACs in from other manufacturers.
Signed-off-by: "Mauro S. M. Rodrigues" <maurosr@linux.vnet.ibm.com> Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The decoding of shortenend codes is broken. It only works as expected if
there are no erasures.
When decoding with erasures, Lambda (the error and erasure locator
polynomial) is initialized from the given erasure positions. The pad
parameter is not accounted for by the initialisation code, and hence
Lambda is initialized from incorrect erasure positions.
The fix is to adjust the erasure positions by the supplied pad.
Signed-off-by: Ferdinand Blomqvist <ferdinand.blomqvist@gmail.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lkml.kernel.org/r/20190620141039.9874-3-ferdinand.blomqvist@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Exynos SoCs based on CA7/CA15 have 2 timer interfaces: custom Exynos MCT
(Multi Core Timer) and standard ARM Architected Timers.
There are use cases, where both timer interfaces are used simultanously.
One of such examples is using Exynos MCT for the main system timer and
ARM Architected Timers for the KVM and virtualized guests (KVM requires
arch timers).
Exynos Multi-Core Timer driver (exynos_mct) must be however started
before ARM Architected Timers (arch_timer), because they both share some
common hardware blocks (global system counter) and turning on MCT is
needed to get ARM Architected Timer working properly.
To ensure selecting Exynos MCT as the main system timer, increase MCT
timer rating. To ensure proper starting order of both timers during
suspend/resume cycle, increase MCT hotplug priority over ARM Archictected
Timers.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org> Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
ZAC support added sense data requesting on error for both ZAC and ATA
devices. This seems to cause erratic error handling behaviors on some
SSDs where the device reports sense data availability and then
delivers the wrong content making EH take the wrong actions. The
failure mode was sporadic on a LITE-ON ssd and couldn't be reliably
reproduced.
There is no value in requesting sense data from non-ZAC ATA devices
while there's a significant risk of introducing EH misbehaviors which
are difficult to reproduce and fix. Let's do the sense data dancing
only for ZAC devices.
Reviewed-by: Hannes Reinecke <hare@suse.com> Tested-by: Masato Suzuki <masato.suzuki@wdc.com> Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Attempting to profile 1024 or more CPUs with perf causes two errors:
perf record -a
[ perf record: Woken up X times to write data ]
way too many cpu caches..
[ perf record: Captured and wrote X MB perf.data (X samples) ]
perf report -C 1024
Error: failed to set cpu bitmap
Requested CPU 1024 too large. Consider raising MAX_NR_CPUS
Increasing MAX_NR_CPUS from 1024 to 2048 and redefining MAX_CACHES as
MAX_NR_CPUS * 4 returns normal functionality to perf:
perf record -a
[ perf record: Woken up X times to write data ]
[ perf record: Captured and wrote X MB perf.data (X samples) ]
perf report -C 1024
...
Signed-off-by: Kyle Meyer <kyle.meyer@hpe.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lkml.kernel.org/r/20190620193630.154025-1-meyerk@stormcage.eag.rdlabs.hpecorp.net Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Observed PCIE device wake up failed after ~120 iterations of
soft-reboot test. The error message is
"ath10k_pci 0000:01:00.0: failed to wake up device : -110"
The call trace as below:
ath10k_pci_probe -> ath10k_pci_force_wake -> ath10k_pci_wake_wait ->
ath10k_pci_is_awake
Once trigger the device to wake up, we will continuously check the RTC
state until it returns RTC_STATE_V_ON or timeout.
But for QCA99x0 chips, we use wrong value for RTC_STATE_V_ON.
Occasionally, we get 0x7 on the fist read, we thought as a failure
case, but actually is the right value, also verified with the spec.
So fix the issue by changing RTC_STATE_V_ON from 0x5 to 0x7, passed
~2000 iterations.
Tested HW: QCA9984
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In function ath10k_sdio_mbox_rx_alloc() [sdio.c],
ath10k_sdio_mbox_alloc_rx_pkt() is called without handling the error cases.
This will make the driver think the allocation for skb is successful and
try to access the skb. If we enable failslab, system will easily crash with
NULL pointer dereferencing.
Call trace of CONFIG_FAILSLAB:
ath10k_sdio_irq_handler+0x570/0xa88 [ath10k_sdio]
process_sdio_pending_irqs+0x4c/0x174
sdio_run_irqs+0x3c/0x64
sdio_irq_work+0x1c/0x28
Fixes: d96db25d2025 ("ath10k: add initial SDIO support") Signed-off-by: Claire Chang <tientzu@chromium.org> Reviewed-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
syzkaller reports for memory leak in start_sync_thread [1]
As Eric points out, kthread may start and stop before the
threadfn function is called, so there is no chance the
data (tinfo in our case) to be released in thread.
Fix this by releasing tinfo in the controlling code instead.
When the device is disconnected while passing traffic it is possible
to receive out of order urbs causing a memory leak since the skb linked
to the current tx urb is not removed. Fix the issue deallocating the skb
cleaning up the tx ring. Moreover this patch fixes the following kernel
warning
Acked-by: Jakub Kicinski <kubakici@wp.pl> Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Without 'set -e', shell scripts continue running even after any
error occurs. The missed 'set -e' is a typical bug in shell scripting.
For example, when a disk space shortage occurs while this script is
running, it actually ends up with generating a truncated capflags.c.
Yet, mkcapflags.sh continues running and exits with 0. So, the build
system assumes it has succeeded.
It will not be re-generated in the next invocation of Make since its
timestamp is newer than that of any of the source files.
Add 'set -e' so that any error in this script is caught and propagated
to the build system.
Since 9c2af1c7377a ("kbuild: add .DELETE_ON_ERROR special target"),
make automatically deletes the target on any failure. So, the broken
capflags.c will be deleted automatically.
Do not schedule rx_tasklet when the usb dongle is disconnected.
Moreover do not grub rx_lock in mt7601u_kill_rx since usb_poison_urb
can run concurrently with urb completion and we can unlink urbs from rx
ring in any order.
This patch fixes the common kernel warning reported when
the device is removed.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
- The wait_event_interruptible() condition calls hdpvr_get_next_buffer(dev)
which uses a mutex, which is not allowed. Rewrite with list_empty_careful()
that doesn't need locking.
- In hdpvr_read() the call to hdpvr_stop_streaming() didn't lock io_mutex,
but it should have since stop_streaming expects that.
- In hdpvr_device_release() io_mutex was locked when calling flush_work(),
but there it shouldn't take that mutex since the work done by flush_work()
also wants to lock that mutex.
There are also two other changes (suggested by Keith):
- msecs_to_jiffies(4000); (a NOP) should have been msleep(4000).
- Change v4l2_dbg to v4l2_info to always log if streaming had to be restarted.
Reported-by: Keith Pyle <kpyle@austin.rr.com> Suggested-by: Keith Pyle <kpyle@austin.rr.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
v4l2_fill_pixfmt() returns -EINVAL if the pixelformat used as parameter is
invalid or if the user is trying to use a multiplanar format with the
singleplanar API. Currently, the vimc_cap_try_fmt_vid_cap() returns such
value, but vimc_cap_s_fmt_vid_cap() is ignoring it. Fix that and returns
an error value if vimc_cap_try_fmt_vid_cap() has failed.
Signed-off-by: André Almeida <andrealmeid@collabora.com> Suggested-by: Helen Koike <helen.koike@collabora.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If no more frames are decoded in bitstream end mode, and a previously
decoded frame has been returned, the firmware still increments the frame
number. To avoid a sequence number mismatch after decoder restart,
increment the sequence_offset correction parameter.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
coda_encoder_cmd() is racy, as the last scheduled picture run worker can
still be in-flight while the ENC_CMD_STOP command is issued. Depending
on the exact timing the sequence numbers might already be changed, but
the last buffer might not have been put on the destination queue yet.
In this case the current implementation would prematurely wake the
destination queue with last_buffer_dequeued=true, causing userspace to
call streamoff before the last buffer is handled.
Close this race window by synchronizing with the pic_run_worker before
doing the sequence check.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
[l.stach@pengutronix.de: switch to flush_work, reword commit message] Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Sequence number handling assumed that the BIT processor frame number
starts counting at 1, but this is not true for the MPEG-2 decoder,
which starts at 0. Fix the sequence counter offset detection to handle
this.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Some Qualcomm Snapdragon based laptops built to run Microsoft Windows
are clearly ACPI 5.1 based, given that that is the first ACPI revision
that supports ARM, and introduced the FADT 'arm_boot_flags' field,
which has a non-zero field on those systems.
So in these cases, infer from the ARM boot flags that the FADT must be
5.1 or later, and treat it as 5.1.
Acked-by: Sudeep Holla <sudeep.holla@arm.com> Tested-by: Lee Jones <lee.jones@linaro.org> Reviewed-by: Graeme Gregory <graeme.gregory@linaro.org> Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Acked-by: Hanjun Guo <guohanjun@huawei.com> Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Don't allow the TAI-UTC offset of the system clock to be set by adjtimex()
to a value larger than 100000 seconds.
This prevents an overflow in the conversion to int, prevents the CLOCK_TAI
clock from getting too far ahead of the CLOCK_REALTIME clock, and it is
still large enough to allow leap seconds to be inserted at the maximum rate
currently supported by the kernel (once per day) for the next ~270 years,
however unlikely it is that someone can survive a catastrophic event which
slowed down the rotation of the Earth so much.
Reported-by: Weikang shi <swkhack@gmail.com> Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: John Stultz <john.stultz@linaro.org> Cc: Prarit Bhargava <prarit@redhat.com> Cc: Richard Cochran <richardcochran@gmail.com> Cc: Stephen Boyd <sboyd@kernel.org> Link: https://lkml.kernel.org/r/20190618154713.20929-1-mlichvar@redhat.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Since the beginning the second clock ('special', 'sclk') was optional and
it is not available on some variants of Exynos SoCs (i.e. Exynos5420 with
v7 of MFC hardware).
However commit 1bce6fb3edf1 ("[media] s5p-mfc: Rework clock handling")
made handling of all specified clocks mandatory. This patch restores
original behavior of the driver and fixes its operation on
Exynos5420 SoCs.
syzkaller reports for memory leak when registering hooks [1]
As we moved the nf_unregister_net_hooks() call into
__ip_vs_dev_cleanup(), defer the nf_register_net_hooks()
call, so that hooks are allocated and freed from same
pernet_operations (ipvs_core_dev_ops).
kernelci.org reports failed builds on arc because of what looks
like an old missed 'select' statement:
net/xfrm/xfrm_algo.o: In function `xfrm_probe_algs':
xfrm_algo.c:(.text+0x1e8): undefined reference to `crypto_has_ahash'
I don't see this in randconfig builds on other architectures, but
it's fairly clear we want to select the hash code for it, like we
do for all its other users. As Herbert points out, CRYPTO_BLKCIPHER
is also required even though it has not popped up in build tests.
Fixes: 17bc19702221 ("ipsec: Use skcipher and ahash when probing algorithms") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In edac_create_csrow_object(), the reference to the object is not
released when adding the device to the device hierarchy fails
(device_add()). This may result in a memory leak.
Vhost_net was known to suffer from HOL[1] issues which is not easy to
fix. Several downstream disable the feature by default. What's more,
the datapath was split and datacopy path got the support of batching
and XDP support recently which makes it faster than zerocopy part for
small packets transmission.
It looks to me that disable zerocopy by default is more
appropriate. It cold be enabled by default again in the future if we
fix the above issues.
Signed-off-by: Jason Wang <jasowang@redhat.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In which case it simply returns "unknown", like when it can't figure out
the evsel->name value.
This makes this code more robust and fixes a problem in 'perf trace'
where a NULL evsel was being passed to a routine that only used the
evsel for printing its name when a invalid syscall id was passed.
Reported-by: Leo Yan <leo.yan@linaro.org> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Namhyung Kim <namhyung@kernel.org> Link: https://lkml.kernel.org/n/tip-f30ztaasku3z935cn3ak3h53@git.kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Recent probing at the Linux Kernel Memory Model uncovered a
'surprise'. Strongly ordered architectures where the atomic RmW
primitive implies full memory ordering and
smp_mb__{before,after}_atomic() are a simple barrier() (such as x86)
fail for:
Because, while the atomic_inc() implies memory order, it
(surprisingly) does not provide a compiler barrier. This then allows
the compiler to re-order like so:
After commit b38ff4075a80, the following command does not work anymore:
$ ip xfrm state add src 10.125.0.2 dst 10.125.0.1 proto esp spi 34 reqid 1 \
mode tunnel enc 'cbc(aes)' 0xb0abdba8b782ad9d364ec81e3a7d82a1 auth-trunc \
'hmac(sha1)' 0xe26609ebd00acb6a4d51fca13e49ea78a72c73e6 96 flag align4
In fact, the selector is not mandatory, allow the user to provide an empty
selector.
Fixes: b38ff4075a80 ("xfrm: Fix xfrm sel prefix length validation") CC: Anirudh Gupta <anirudh.gupta@sophos.com> Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Acked-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
wbc_account_io() collects information on cgroup ownership of writeback
pages to determine which cgroup should own the inode. Pages can stay
associated with dead memcgs but we want to avoid attributing IOs to
dead blkcgs as much as possible as the association is likely to be
stale. However, currently, pages associated with dead memcgs
contribute to the accounting delaying and/or confusing the
arbitration.
Fix it by ignoring pages associated with dead memcgs.
Signed-off-by: Tejun Heo <tj@kernel.org> Cc: Jan Kara <jack@suse.cz> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Add the CPUID enumeration for Intel's de-feature bits to accommodate
passing these de-features through to kvm guests.
These de-features are (from SDM vol 1, section 8.1.8):
- X86_FEATURE_FDP_EXCPTN_ONLY: If CPUID.(EAX=07H,ECX=0H):EBX[bit 6] = 1, the
data pointer (FDP) is updated only for the x87 non-control instructions that
incur unmasked x87 exceptions.
- X86_FEATURE_ZERO_FCS_FDS: If CPUID.(EAX=07H,ECX=0H):EBX[bit 13] = 1, the
processor deprecates FCS and FDS; it saves each as 0000H.
Signed-off-by: Aaron Lewis <aaronlewis@google.com> Signed-off-by: Borislav Petkov <bp@suse.de> Reviewed-by: Jim Mattson <jmattson@google.com> Cc: Fenghua Yu <fenghua.yu@intel.com> Cc: Frederic Weisbecker <frederic@kernel.org> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: marcorr@google.com Cc: Peter Feiner <pfeiner@google.com> Cc: pshier@google.com Cc: Robert Hoo <robert.hu@linux.intel.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Thomas Lendacky <Thomas.Lendacky@amd.com> Cc: x86-ml <x86@kernel.org> Link: https://lkml.kernel.org/r/20190605220252.103406-1-aaronlewis@google.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When debugging options are turned on, the rcu_read_lock() function
might not be inlined. This results in lockdep's print_lock() function
printing "rcu_read_lock+0x0/0x70" instead of rcu_read_lock()'s caller.
For example:
[ 10.579995] =============================
[ 10.584033] WARNING: suspicious RCU usage
[ 10.588074] 4.18.0.memcg_v2+ #1 Not tainted
[ 10.593162] -----------------------------
[ 10.597203] include/linux/rcupdate.h:281 Illegal context switch in
RCU read-side critical section!
[ 10.606220]
[ 10.606220] other info that might help us debug this:
[ 10.606220]
[ 10.614280]
[ 10.614280] rcu_scheduler_active = 2, debug_locks = 1
[ 10.620853] 3 locks held by systemd/1:
[ 10.624632] #0: (____ptrval____) (&type->i_mutex_dir_key#5){.+.+}, at: lookup_slow+0x42/0x70
[ 10.633232] #1: (____ptrval____) (rcu_read_lock){....}, at: rcu_read_lock+0x0/0x70
[ 10.640954] #2: (____ptrval____) (rcu_read_lock){....}, at: rcu_read_lock+0x0/0x70
These "rcu_read_lock+0x0/0x70" strings are not providing any useful
information. This commit therefore forces inlining of the rcu_read_lock()
function so that rcu_read_lock()'s caller is instead shown.
Signed-off-by: Waiman Long <longman@redhat.com> Signed-off-by: Paul E. McKenney <paulmck@linux.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Compiling kernel/bpf/core.c with W=1 causes a flood of warnings:
kernel/bpf/core.c:1198:65: warning: initialized field overwritten [-Woverride-init]
1198 | #define BPF_INSN_3_TBL(x, y, z) [BPF_##x | BPF_##y | BPF_##z] = true
| ^~~~
kernel/bpf/core.c:1087:2: note: in expansion of macro 'BPF_INSN_3_TBL'
1087 | INSN_3(ALU, ADD, X), \
| ^~~~~~
kernel/bpf/core.c:1202:3: note: in expansion of macro 'BPF_INSN_MAP'
1202 | BPF_INSN_MAP(BPF_INSN_2_TBL, BPF_INSN_3_TBL),
| ^~~~~~~~~~~~
kernel/bpf/core.c:1198:65: note: (near initialization for 'public_insntable[12]')
1198 | #define BPF_INSN_3_TBL(x, y, z) [BPF_##x | BPF_##y | BPF_##z] = true
| ^~~~
kernel/bpf/core.c:1087:2: note: in expansion of macro 'BPF_INSN_3_TBL'
1087 | INSN_3(ALU, ADD, X), \
| ^~~~~~
kernel/bpf/core.c:1202:3: note: in expansion of macro 'BPF_INSN_MAP'
1202 | BPF_INSN_MAP(BPF_INSN_2_TBL, BPF_INSN_3_TBL),
| ^~~~~~~~~~~~
98 copies of the above.
The attached patch silences the warnings, because we *know* we're overwriting
the default initializer. That leaves bpf/core.c with only 6 other warnings,
which become more visible in comparison.
On buses like SlimBus and SoundWire which does not support
gather_writes yet in regmap, A bulk write on paged register
would be silently ignored after programming page.
This is because local variable 'ret' value in regmap_raw_write_impl()
gets reset to 0 once page register is written successfully and the
code below checks for 'ret' value to be -ENOTSUPP before linearising
the write buffer to send to bus->write().
Fix this by resetting the 'ret' value to -ENOTSUPP in cases where
gather_writes() is not supported or single register write is
not possible.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
NOTE: There must be a correlation between the wake-up enable and
interrupt-enable registers. If a GPIO pin has a wake-up configured
on it, it must also have the corresponding interrupt enabled (on
one of the two interrupt lines).
Ensure that this condition is always satisfied by enabling the detection
events after enabling the interrupt, and disabling the detection before
disabling the interrupt. This ensures interrupt/wakeup events can not
happen until both the wakeup and interrupt enables correlate.
If we do any clearing, clear between the interrupt enable/disable and
trigger setting.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Tested-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Commit 384ebe1c2849 ("gpio/omap: Add DT support to GPIO driver") added
the register definition tables to the gpio-omap driver. Subsequently to
that commit, commit 4e962e8998cc ("gpio/omap: remove cpu_is_omapxxxx()
checks from *_runtime_resume()") added definitions for irqstatus_raw*
registers to the legacy OMAP4 definitions, but missed the DT
definitions.
This causes an unintentional change of behaviour for the 1.101 errata
workaround on OMAP4 platforms. Fix this oversight.
Fixes: 4e962e8998cc ("gpio/omap: remove cpu_is_omapxxxx() checks from *_runtime_resume()") Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Tested-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In case we expand an existing region, we unlink
this latter and insert the larger one. In
that case we should free the original region after
the insertion. Also we can immediately return.
New Gen3 R-Car platforms incorporate the FDP1 with an updated version
register. No code change is required to support these targets, but they
will currently report an error stating that the device can not be
identified.
Update the driver to match against the new device types.
when the kvm module is not loaded or not built in.
Fix this by adding a valid function which tests if the module
is loaded. Loaded modules (or builtin KVM support) have a
directory named
/sys/kernel/debug/tracing/events/kvm-s390
for this tracepoint.
Check for existence of this directory.
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com> Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Hendrik Brueckner <brueckner@linux.vnet.ibm.com> Link: http://lkml.kernel.org/r/20190604053504.43073-1-tmricht@linux.ibm.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
[ kleber: replaced get/put_events_file() by get/put_tracing_file() as 40c3c0c9ac2b (tools lib api fs tracing_path: Introduce
get/put_events_file() helpers) is missing. ] Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Jiri Olsa [Mon, 11 Jun 2018 09:34:22 +0000 (11:34 +0200)]
perf tests: Add valid callback for parse-events test
BugLink: https://bugs.launchpad.net/bugs/1839036
Adding optional 'valid' callback for events tests in parse-events
object, so we don't try to parse PMUs, which are not supported.
Following line is displayed for skipped test:
running test 52 'intel_pt//u'... SKIP
Committer note:
Use named initializers in the struct evlist_test variable to avoid
breaking the build on centos:5, 6 and others with a similar gcc:
cc1: warnings being treated as errors
tests/parse-events.c: In function 'test_pmu_events':
tests/parse-events.c:1817: error: missing initializer
tests/parse-events.c:1817: error: (near initialization for 'e.type')
Signed-off-by: Jiri Olsa <jolsa@kernel.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: David Ahern <dsahern@gmail.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Hendrik Brueckner <brueckner@linux.vnet.ibm.com> Cc: Kim Phillips <kim.phillips@arm.com> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Richter <tmricht@linux.ibm.com> Link: http://lkml.kernel.org/r/20180611093422.1005-2-jolsa@kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
(backported from commit 16ddcfbf7f3d07aa781e26b39f2c28636a4ed2fd)
[ kleber: skipped the intel_pt chunk as b3f58c8da64b (perf tests
parse-events: Add intel_pt parse test) has not been applied yet ] Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
This patch adds the necessary intelligence to properly compute the value
of 'old' and 'head' when operating in snapshot mode. That way we can
get the latest information in the AUX buffer and be compatible with the
generic AUX ring buffer mechanic.
Tester notes:
> Leo, have you had the chance to test/review this one? Suzuki?
Sure. I applied this patch on the perf/core branch (with latest
commit 3e4fbf36c1e3 'perf augmented_raw_syscalls: Move reading
filename to the loop') and passed testing with below steps:
# perf record -e cs_etm/@tmc_etr0/ -S -m,64 --per-thread ./sort &
[1] 19097
Bubble sorting array of 30000 elements
# kill -USR2 19097
# kill -USR2 19097
# kill -USR2 19097
[ perf record: Woken up 4 times to write data ]
[ perf record: Captured and wrote 0.753 MB perf.data ]
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org> Tested-by: Leo Yan <leo.yan@linaro.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Suzuki Poulouse <suzuki.poulose@arm.com> Cc: linux-arm-kernel@lists.infradead.org Link: http://lkml.kernel.org/r/20190605161633.12245-1-mathieu.poirier@linaro.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If a fresh array block is allocated during resize, the current in-memory
set size should be increased by the size of the block, not replaced by it.
Before the fix, adding entries to a hash set type, leading to a table
resize, caused an inconsistent memory size to be reported. This becomes
more obvious when swapping sets with similar sizes:
# cat hash_ip_size.sh
#!/bin/sh
FAIL_RETRIES=10
tries=0
while [ ${tries} -lt ${FAIL_RETRIES} ]; do
ipset create t1 hash:ip
for i in `seq 1 4345`; do
ipset add t1 1.2.$((i / 255)).$((i % 255))
done
t1_init="$(ipset list t1|sed -n 's/Size in memory: \(.*\)/\1/p')"
ipset create t2 hash:ip
for i in `seq 1 4360`; do
ipset add t2 1.2.$((i / 255)).$((i % 255))
done
t2_init="$(ipset list t2|sed -n 's/Size in memory: \(.*\)/\1/p')"
ipset swap t1 t2
t1_swap="$(ipset list t1|sed -n 's/Size in memory: \(.*\)/\1/p')"
t2_swap="$(ipset list t2|sed -n 's/Size in memory: \(.*\)/\1/p')"
sfp_check_state can potentially be called by both a threaded IRQ handler
and delayed work. If it is concurrently called, it could result in
incorrect state management. Add a st_mutex to protect the state - this
lock gets taken outside of code that checks and handle state changes, and
the existing sm_mutex nests inside of it.
Suggested-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Robert Hancock <hancock@sedsystems.ca> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When inserting random PFNs for debugging the CEC through
(debugfs)/ras/cec/pfn, depending on the return value of pfn_set(),
multiple values get inserted per a single write.
That is because simple_attr_write() interprets a retval of 0 as
success and claims the whole input. However, pfn_set() returns the
cec_add_elem() value, which, if > 0 and smaller than the whole input
length, makes glibc continue issuing the write syscall until there's
input left:
When a CQ-enabled device uses QEBSM for SBAL state inspection,
get_buf_states() can return the PENDING state for an Output Queue.
get_outbound_buffer_frontier() isn't prepared for this, and any PENDING
buffer will permanently stall all further completion processing on this
Queue.
This isn't a concern for non-QEBSM devices, as get_buf_states() for such
devices will manually turn PENDING buffers into EMPTY ones.
Fixes: 104ea556ee7f ("qdio: support asynchronous delivery of storage blocks") Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
projects / mirror_ubuntu-bionic-kernel.git / log