include attributes.txt
[pve-docs.git] / pve-installation.adoc
1 Installing Proxmox VE
2 ---------------------
3 include::attributes.txt[]
5 {pve} ships as a set of Debian packages, so you can simply install it
6 on top of a normal Debian installation. After configuring the
7 repositories, you need to run:
9 [source,bash]
10 ----
11 apt-get update
12 apt-get install proxmox-ve
13 ----
15 While this looks easy, it presumes that you have correctly installed
16 the base system, and you know how you want to configure and use the
17 local storage. Network configuration is also completely up to you.
19 In general, this is not trivial, especially when you use LVM or
20 ZFS. This is why we provide an installation CD-ROM for {pve}. That
21 installer just ask you a few questions, then partitions the local
22 disk(s), installs all required packages, and configures the system
23 including a basic network setup. You can get a fully functional system
24 within a few minutes, including the following:
26 * Complete operating system (Debian Linux, 64-bit)
27 * Partition the hard drive with ext4 (alternative ext3 or xfs) or ZFS
28 * {pve} Kernel with LXC and KVM support
29 * Complete toolset
30 * Web based management interface
32 NOTE: By default, the complete server is used and all existing data is
33 removed.
35 Using the {pve} Installation CD-ROM
36 ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
38 Please insert the installation CD-ROM, then boot from that
39 drive. Immediately afterwards you can choose the following menu
40 options:
42 Install Proxmox VE::
44 Start normal installation.
46 Install Proxmox VE (Debug mode)::
48 Start installation in debug mode. It opens a shell console at several
49 installation steps, so that you can debug things if something goes
50 wrong. Please press `CTRL-D` to exit those debug consoles and continue
51 installation. This option is mostly for developers and not meant for
52 general use.
54 Rescue Boot::
56 This option allows you to boot an existing installation. It searches
57 all attached hard disks, and if it finds an existing installation,
58 boots directly into that disk using the existing Linux kernel. This
59 can be useful if there are problems with the boot block (grub), or the
60 BIOS is unable to read the boot block from the disk.
62 Test Memory::
64 Runs 'memtest86+'. This is useful to check if your memory if
65 functional and error free.
67 You normally select *Install Proxmox VE* to start the installation.
68 After that you get prompted to select the target hard disk(s). The
69 `Options` button lets you select the target file system, which
70 defaults to `ext4`. The installer uses LVM if you select 'ext3',
71 'ext4' or 'xfs' as file system, and offers additional option to
72 restrict LVM space (see <<advanced_lvm_options,below>>)
74 If you have more than one disk, you can also use ZFS as file system.
75 ZFS supports several software RAID levels, so this is specially useful
76 if you do not have a hardware RAID controller. The `Options` button
77 lets you select the ZFS RAID level, and you can choose disks there.
79 The next pages just asks for basic configuration options like time
80 zone and keyboard layout. You also need to specify your email address
81 and select a superuser password.
83 The last step is the network configuration. Please note that you can
84 use either IPv4 or IPv6 here, but not both. If you want to configure a
85 dual stack node, you can easily do that after installation.
87 If you press `Next` now, installation starts to format disks, and
88 copies packages to the target. Please wait until that is finished,
89 then reboot the server.
91 Further configuration is done via the Proxmox web interface. Just
92 point your browser to the IP address given during installation
93 (https://youripaddress:8006). {pve} is tested for IE9, Firefox 10
94 and higher, and Google Chrome.
97 [[advanced_lvm_options]]
98 Advanced LVM configuration options
99 ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
101 The installer creates a Volume Group (VG) called `pve`, and additional
102 Logical Volumes (LVs) called `root`, `data` and `swap`. The size of
103 those volumes can be controlled with:
105 `hdsize`::
107 Defines the total HD size to be used. This way you can save free
108 space on the HD for further partitioning (i.e. for an additional PV
109 and VG on the same hard disk that can be used for LVM storage).
111 `swapsize`::
113 To define the size of the `swap` volume. Default is the same size as
114 installed RAM, with 4GB minimum and `hdsize/8` as maximum.
116 `maxroot`::
118 The `root` volume size. The `root` volume stores the whole operation
119 system.
121 `maxvz`::
123 Define the size of the `data` volume, which is mounted at
124 '/var/lib/vz'.
126 `minfree`::
128 To define the amount of free space left in LVM volume group `pve`.
129 16GB is the default if storage available > 128GB, `hdsize/8` otherwise.
130 +
131 NOTE: LVM requires free space in the VG for snapshot creation (not
132 required for lvmthin snapshots).
135 ZFS Performance Tips
136 ^^^^^^^^^^^^^^^^^^^^
138 ZFS uses a lot of memory, so it is best to add additional 8-16GB RAM
139 if you want to use ZFS.
141 ZFS also provides the feature to use a fast SSD drive as write cache. The
142 write cache is called the ZFS Intent Log (ZIL). You can add that after
143 installation using the following command:
145 zpool add <pool-name> log </dev/path_to_fast_ssd>