The USB-serial console implementation has never reported the actual
terminal settings used. Despite storing the corresponding cflags in its
struct console, these were never honoured on later tty open() where the
tty termios would be left initialised to the driver defaults.
Unlike the serial console implementation, the USB-serial code calls
subdriver open() already at console setup. While calling set_termios()
and write() before open() looks like it could work for some USB-serial
drivers, others definitely do not expect this, so modelling this after
serial core is going to be intrusive, if at all possible.
Instead, use a (renamed) tty helper to save the termios data used at
console setup so that the tty termios reflects the actual terminal
settings after a subsequent tty open().
Note that the calls to tty_init_termios() (tty_driver_install()) and
tty_save_termios() are serialised using the disconnect mutex.
This specifically fixes a regression that was triggered by a recent
change adding software flow control to the pl2303 driver: a getty trying
to disable flow control while leaving the baud rate unchanged would now
also set the baud rate to the driver default (prior to the flow-control
change this had been a noop).
Fixes: 7041d9c3f01b ("USB: serial: pl2303: add support for tx xon/xoff flow control") Cc: stable <stable@vger.kernel.org> # 4.18 Cc: Florian Zumbiehl <florz@florz.de> Reported-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Fix a deadlock whereby the NFSv4 state manager can get stuck in the
delegation return code, waiting for a layout return to complete in
another thread. If the server reboots before that other thread
completes, then we need to be able to start a second state
manager thread in order to perform recovery.
Prevent exceptions from being raised while decoding output
from an executed command. There is no impact on tdc's
execution and the verify command phase would fail the pattern
match.
Signed-off-by: Lucas Bates <lucasb@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
As pointed out by Gregor, spitz keyboard matrix is broken, with or
without CONFIG_PINCTRL set, quoting :
"The gpio matrix keypard on the Zaurus C3x00 (see spitz.c) does not work
properly. Noticeable are that rshift+c does nothing where as lshift+c
creates C. Opposite it is for rshift+a vs lshift+a, here only rshift
works. This affects a few other combinations using the rshift or lshift
buttons."
As a matter of fact, as for platform_data based builds CONFIG_PINCTRL=n
is required for now (as opposed for devicetree builds where it should be
set), this means gpio driver should change the direction, which is what
was attempted by commit c4e5ffb6f224 ("gpio: pxa: fix legacy non pinctrl
aware builds").
Unfortunately, the input case was inverted, and the direction change was
never done. This wasn't seen up until now because the initial platform
setup (MFP) was setting this direction. Yet in Gregory's case, the
matrix-keypad driver changes back and forth the direction dynamically,
and this is why he's the first to report it.
Certain flows need to access the rdma-info structure, for example dcbx
update flows. In some cases there can be a race between the allocation or
deallocation of the structure which was done in roce start / roce stop and
an asynchrounous dcbx event that tries to access the structure.
For this reason, we move the allocation of the rdma_info structure to be
similar to the iscsi/fcoe info structures which are allocated during device
setup.
We add a new field of "active" to the struct to define whether roce has
already been started or not, and this is checked instead of whether the
pointer to the info structure.
Fixes: 51ff17251c9c ("qed: Add support for RoCE hw init") Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com> Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
NullFunc packets should never be duplicate just like
QoS-NullFunc packets.
We saw a client that enters / exits power save with
NullFunc frames (and not with QoS-NullFunc) despite the
fact that the association supports HT.
This specific client also re-uses a non-zero sequence number
for different NullFunc frames.
At some point, the client had to send a retransmission of
the NullFunc frame and we dropped it, leading to a
misalignment in the power save state.
Fix this by never consider a NullFunc frame as duplicate,
just like we do for QoS NullFunc frames.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=201449
If the buffered broadcast queue contains packets, letting new packets bypass
that queue can lead to heavy reordering, since the driver is probably throttling
transmission of buffered multicast packets after beacons.
Keep buffering packets until the buffer has been cleared (and no client
is in powersave mode).
Make it behave like regular ieee80211_tx_status calls, except for the lack of
filtered frame processing.
This fixes spurious low-ack triggered disconnections with powersave clients
connected to an AP.
This fixes stale beacon-int values that would keep a netdev
from going up.
To reproduce:
Create two VAP on one radio.
vap1 has beacon-int 100, start it.
vap2 has beacon-int 240, start it (and it will fail
because beacon-int mismatch).
reconfigure vap2 to have beacon-int 100 and start it.
It will fail because the stale beacon-int 240 will be used
in the ifup path and hostapd never gets a chance to set the
new beacon interval.
Commit cfe30b872058 "libnvdimm, pmem: adjust for section collisions with
'System RAM'" enabled Linux to workaround occasions where platform
firmware arranges for "System RAM" and "Persistent Memory" to collide
within a single section boundary. Unfortunately, as reported in this
issue [1], platform firmware can inflict the same collision between
persistent memory regions.
The approach of interrogating iomem_resource does not work in this
case because platform firmware may merge multiple regions into a single
iomem_resource range. Instead provide a method to interrogate regions
that share the same parent bus.
This is a stop-gap until the core-MM can grow support for hotplug on
sub-section boundaries.
[1]: https://github.com/pmem/ndctl/issues/76
Fixes: cfe30b872058 ("libnvdimm, pmem: adjust for section collisions with...") Cc: <stable@vger.kernel.org> Reported-by: Patrick Geary <patrickg@supermicro.com> Tested-by: Patrick Geary <patrickg@supermicro.com> Reviewed-by: Vishal Verma <vishal.l.verma@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This patch is trying to fix KE issue due to
"BUG: KASAN: global-out-of-bounds in param_set_kgdboc_var+0x194/0x198"
reported by Syzkaller scan."
[26364:syz-executor0][name:report8t]BUG: KASAN: global-out-of-bounds in param_set_kgdboc_var+0x194/0x198
[26364:syz-executor0][name:report&]Read of size 1 at addr ffffff900e44f95f by task syz-executor0/26364
[26364:syz-executor0][name:report&]
[26364:syz-executor0]CPU: 7 PID: 26364 Comm: syz-executor0 Tainted: G W 0
[26364:syz-executor0]Call trace:
[26364:syz-executor0][<ffffff9008095cf8>] dump_bacIctrace+Ox0/0x470
[26364:syz-executor0][<ffffff9008096de0>] show_stack+0x20/0x30
[26364:syz-executor0][<ffffff90089cc9c8>] dump_stack+Oxd8/0x128
[26364:syz-executor0][<ffffff90084edb38>] print_address_description +0x80/0x4a8
[26364:syz-executor0][<ffffff90084ee270>] kasan_report+Ox178/0x390
[26364:syz-executor0][<ffffff90084ee4a0>] _asan_report_loadi_noabort+Ox18/0x20
[26364:syz-executor0][<ffffff9008b092ac>] param_set_kgdboc_var+Ox194/0x198
[26364:syz-executor0][<ffffff900813af64>] param_attr_store+Ox14c/0x270
[26364:syz-executor0][<ffffff90081394c8>] module_attr_store+0x60/0x90
[26364:syz-executor0][<ffffff90086690c0>] sysfs_kl_write+Ox100/0x158
[26364:syz-executor0][<ffffff9008666d84>] kernfs_fop_write+0x27c/0x3a8
[26364:syz-executor0][<ffffff9008508264>] do_loop_readv_writev+0x114/0x1b0
[26364:syz-executor0][<ffffff9008509ac8>] do_readv_writev+0x4f8/0x5e0
[26364:syz-executor0][<ffffff9008509ce4>] vfs_writev+0x7c/Oxb8
[26364:syz-executor0][<ffffff900850ba64>] SyS_writev+Oxcc/0x208
[26364:syz-executor0][<ffffff90080883f0>] elO_svc_naked +0x24/0x28
[26364:syz-executor0][name:report&]
[26364:syz-executor0][name:report&]The buggy address belongs to the variable:
[26364:syz-executor0][name:report&] kgdb_tty_line+Ox3f/0x40
[26364:syz-executor0][name:report&]
[26364:syz-executor0][name:report&]Memory state around the buggy address:
[26364:syz-executor0] ffffff900e44f800: 00 00 00 00 00 04 fa fa fa fa fa fa 00 fa fa fa
[26364:syz-executor0] ffffff900e44f880: fa fa fa fa 00 fa fa fa fa fa fa fa 00 fa fa fa
[26364:syz-executor0]> ffffff900e44f900: fa fa fa fa 04 fa fa fa fa fa fa fa 00 00 00 00
[26364:syz-executor0][name:report&] ^
[26364:syz-executor0] ffffff900e44f980: 00 fa fa fa fa fa fa fa 04 fa fa fa fa fa fa fa
[26364:syz-executor0] ffffff900e44fa00: 04 fa fa fa fa fa fa fa 00 fa fa fa fa fa fa fa
[26364:syz-executor0][name:report&]
[26364:syz-executor0][name:panic&]Disabling lock debugging due to kernel taint
[26364:syz-executor0]------------[cut here]------------
After checking the source code, we've found there might be an out-of-bounds
access to "config[len - 1]" array when the variable "len" is zero.
serial8250_register_8250_port calls uart_config_port, which calls
config_port on the port before it tries to power on the port. So we need
the port to be on before calling serial8250_register_8250_port. Change
the code to always do a runtime resume in probe before registering port,
and always do a runtime suspend in remove.
This basically reverts the change in commit 68e5fc4a255a ("tty: serial:
8250_mtk: use pm_runtime callbacks for enabling"), but still use
pm_runtime callbacks.
Fixes: 68e5fc4a255a ("tty: serial: 8250_mtk: use pm_runtime callbacks for enabling") Signed-off-by: Peter Shih <pihsun@chromium.org> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In commit 8b7a13c3f404 ("staging: r8712u: Fix possible buffer
overrun") we fix a potential off by one by making the limit smaller.
The better fix is to make the buffer larger. This makes it match up
with the similar code in other drivers.
gcc-8 rightfully warns that this instance of strncpy is just copying
from the source, to the same source, for a few bytes. Meaning this call
does nothing. As the author of the code obviously meant it to do
something, but this code must be working properly, just replace the call
to the kernel internal strscpy() which gcc doesn't know about, so the
warning goes away.
As this driver was deleted from newer kernel versions, none of this
really matters but now at least we do not have to worry about a build
warning in the stable trees.
When someone writes:
strncpy(dest, source, sizeof(source));
they really are just doing the same thing as:
strcpy(dest, source);
but somehow they feel better because they are now using the "safe"
version of the string functions. Cargo-cult programming at its
finest...
gcc-8 rightfully warns you about doing foolish things like this. Now
that the stable kernels are all starting to be built using gcc-8, let's
get rid of this warning so that we do not have to gaze at this horror.
To dropt the warning, just convert the code to using strcpy() so that if
someone really wants to audit this code and find all of the obvious
problems, it will be easier to do so.
This patch adds f2fs_is_valid_blkaddr() in below functions to do sanity
check with block address to avoid pentential panic:
- f2fs_grab_read_bio()
- __written_first_block()
Don't allow USB3 U1 or U2 if the latency to wake up from the U-state
reaches the service interval for a periodic endpoint.
This is according to xhci 1.1 specification section 4.23.5.2 extra note:
"Software shall ensure that a device is prevented from entering a U-state
where its worst case exit latency approaches the ESIT."
Allowing too long exit latencies for periodic endpoint confuses xHC
internal scheduling, and new devices may fail to enumerate with a
"Not enough bandwidth for new device state" error from the host.
The arm compiler internally interprets an inline assembly label
as an unsigned long value, not a pointer. As a result, under
CONFIG_FORTIFY_SOURCE, the address of a label has a size of 4 bytes,
which was tripping the runtime checks. Instead, we can just cast the label
(as done with the size calculations earlier).
The driver defines three states for a cppi channel.
- idle: .chan_busy == 0 && not in .pending list
- pending: .chan_busy == 0 && in .pending list
- busy: .chan_busy == 1 && not in .pending list
There are cases in which the cppi channel could be in the pending state
when cppi41_dma_issue_pending() is called after cppi41_runtime_suspend()
is called.
cppi41_stop_chan() has a bug for these cases to set channels to idle state.
It only checks the .chan_busy flag, but not the .pending list, then later
when cppi41_runtime_resume() is called the channels in .pending list will
be transitioned to busy state.
Removing channels from the .pending list solves the problem.
Fixes: 975faaeb9985 ("dma: cppi41: start tear down only if channel is busy") Cc: stable@vger.kernel.org # v3.15+ Signed-off-by: Bin Liu <b-liu@ti.com> Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
call_encode can be invoked more than once per RPC call. Ensure that
each call to gss_wrap_req_priv does not overwrite pointers to
previously allocated memory.
We've got a regression report for some Thinkpad models (at least
T570s) which shows the too low speaker output volume. The bisection
leaded to the commit 61fcf8ece9b6 ("ALSA: hda/realtek - Enable Thinkpad
Dock device for ALC298 platform"), and it's basically adding the two
pin configurations for the dock, and looks harmless.
The real culprit seems, though, that the DAC assignment for the
speaker pin is implicitly assumed on these devices, i.e. pin NID 0x14
to be coupled with DAC NID 0x03. When more pins are configured by the
commit above, the auto-parser changes the DAC assignment, and this
resulted in the regression.
As a workaround, just provide the fixed pin / DAC mapping table for
this Thinkpad fixup function. It's no generic solution, but the
problem itself is pretty much device-specific, so must be good
enough.
As addressed in alsa-lib (commit b420056604f0), we need to fix the
case where the evaluation of PCM interval "(x x+1]" leading to
-EINVAL. After applying rules, such an interval may be translated as
"(x x+1)".
Currently the PCM core calls snd_pcm_unlink() always unconditionally
at closing a stream. However, since snd_pcm_unlink() invokes the
global rwsem down, the lock can be easily contended. More badly, when
a thread runs in a high priority RT-FIFO, it may stall at spinning.
Basically the call of snd_pcm_unlink() is required only for the linked
streams that are already rare occasion. For normal use cases, this
code path is fairly superfluous.
As an optimization (and also as a workaround for the RT problem
above in normal situations without linked streams), this patch adds a
check before calling snd_pcm_unlink() and calls it only when needed.
Commit 67ec1072b053 ("ALSA: pcm: Fix rwsem deadlock for non-atomic PCM
stream") fixes deadlock for non-atomic PCM stream. But, This patch
causes antother stuck.
If writer is RT thread and reader is a normal thread, the reader
thread will be difficult to get scheduled. It may not give chance to
release readlocks and writer gets stuck for a long time if they are
pinned to single cpu.
The deadlock described in the previous commit is because the linux
rwsem queues like a FIFO. So, we might need non-FIFO writelock, not
non-block one.
My suggestion is that the writer gives reader a chance to be scheduled
by using the minimum msleep() instaed of spinning without blocking by
writer. Also, The *_nonblock may be changed to *_nonfifo appropriately
to this concept.
In terms of performance, when trylock is failed, this minimum periodic
msleep will have the same performance as the tick-based
schedule()/wake_up_q().
[ Although this has a fairly high performance penalty, the relevant
code path became already rare due to the previous commit ("ALSA:
pcm: Call snd_pcm_unlink() conditionally at closing"). That is, now
this unconditional msleep appears only when using linked streams,
and this must be a rare case. So we accept this as a quick
workaround until finding a more suitable one -- tiwai ]
Some lower volume SanDisk Ultra Flair in 16GB, which the VID:PID is
in 0781:5591, will aggressively request LPM of U1/U2 during runtime,
when using this thumb drive as the OS installation key we found the
device will generate failure during U1 exit path making it dropped
from the USB bus, this causes a corrupted installation in system at
the end.
i.e.,
[ 166.918296] hub 2-0:1.0: state 7 ports 7 chg 0000 evt 0004
[ 166.918327] usb usb2-port2: link state change
[ 166.918337] usb usb2-port2: do warm reset
[ 166.970039] usb usb2-port2: not warm reset yet, waiting 50ms
[ 167.022040] usb usb2-port2: not warm reset yet, waiting 200ms
[ 167.276043] usb usb2-port2: status 02c0, change 0041, 5.0 Gb/s
[ 167.276050] usb 2-2: USB disconnect, device number 2
[ 167.276058] usb 2-2: unregistering device
[ 167.276060] usb 2-2: unregistering interface 2-2:1.0
[ 167.276170] xhci_hcd 0000:00:15.0: shutdown urb ffffa3c7cc695cc0 ep1in-bulk
[ 167.284055] sd 0:0:0:0: [sda] tag#0 FAILED Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
[ 167.284064] sd 0:0:0:0: [sda] tag#0 CDB: Read(10) 28 00 00 33 04 90 00 01 00 00
...
Analyzed the USB trace in the link layer we realized it is because
of the 6-ms timer of tRecoveryConfigurationTimeout which documented
on the USB 3.2 Revision 1.0, the section 7.5.10.4.2 of "Exit from
Recovery.Configuration"; device initiates U1 exit -> Recovery.Active
-> Recovery.Configuration, then the host timer timeout makes the link
transits to eSS.Inactive -> Rx.Detect follows by a Warm Reset.
Interestingly, the other higher volume of SanDisk Ultra Flair sharing
the same VID:PID, such as 64GB, would not request LPM during runtime,
it sticks at U0 always, thus disabling LPM does not affect those thumb
drives at all.
The same odd occures in SanDisk Ultra Fit 16GB, VID:PID in 0781:5583.
Signed-off-by: Harry Pan <harry.pan@intel.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
of_find_node_by_path() acquires a reference to the node
returned by it and that reference needs to be dropped by its caller.
This place doesn't do that, so fix it.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
team_notify_peers() will send ARP and NA to notify peers. team_mcast_rejoin()
will send multicast join group message to notify peers. We should do this when
enabling/changed to a new port. But it doesn't make sense to do it when a port
is disabled.
On the other hand, when we set mcast_rejoin_count to 2, and do a failover,
team_port_disable() will increase mcast_rejoin.count_pending to 2 and then
team_port_enable() will increase mcast_rejoin.count_pending to 4. We will send
4 mcast rejoin messages at latest, which will make user confused. The same
with notify_peers.count.
Fix it by deleting team_notify_peers() and team_mcast_rejoin() in
team_port_disable().
Reported-by: Liang Li <liali@redhat.com> Fixes: fc423ff00df3a ("team: add peer notification") Fixes: 492b200efdd20 ("team: add support for sending multicast rejoins") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In the original ftmac100_interrupt(), the interrupts are only disabled when
the condition "netif_running(netdev)" is true. However, this condition
causes kerenl hang in the following case. When the user requests to
disable the network device, kernel will clear the bit __LINK_STATE_START
from the dev->state and then call the driver's ndo_stop function. Network
device interrupts are not blocked during this process. If an interrupt
occurs between clearing __LINK_STATE_START and stopping network device,
kernel cannot disable the interrupts due to the condition
"netif_running(netdev)" in the ISR. Hence, kernel will hang due to the
continuous interruption of the network device.
In order to solve the above problem, the interrupts of the network device
should always be disabled in the ISR without being restricted by the
condition "netif_running(netdev)".
[V2]
Remove unnecessary curly braces.
Signed-off-by: Vincent Chen <vincentc@andestech.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The getter callers doesn't know the valid Physical Queues (PQ) values.
This patch makes sure that a valid PQ will always be returned.
The patch consists of 3 fixes:
- When qed_init_qm_get_idx_from_flags() receives a disabled flag, it
returned PQ 0, which can potentially be another function's pq. Verify
that flag is enabled, otherwise return default start_pq.
- When qed_init_qm_get_idx_from_flags() receives an unknown flag, it
returned NULL and could lead to a segmentation fault. Return default
start_pq instead.
- A modulo operation was added to MCOS/VFS PQ getters to make sure the
PQ returned is in range of the required flag.
Fixes: b5a9ee7cf3be ("qed: Revise QM cofiguration") Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com> Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The current Cadence QSPI driver caused a kernel panic sporadically
when writing to QSPI. The problem was caused by writing more bytes
than needed because the QSPI operated on 4 bytes at a time.
<snip>
[ 11.202044] Unable to handle kernel paging request at virtual address bffd3000
[ 11.209254] pgd = e463054d
[ 11.211948] [bffd3000] *pgd=2fffb811, *pte=00000000, *ppte=00000000
[ 11.218202] Internal error: Oops: 7 [#1] SMP ARM
[ 11.222797] Modules linked in:
[ 11.225844] CPU: 1 PID: 1317 Comm: systemd-hwdb Not tainted 4.17.7-d0c45cd44a8f
[ 11.235796] Hardware name: Altera SOCFPGA Arria10
[ 11.240487] PC is at __raw_writesl+0x70/0xd4
[ 11.244741] LR is at cqspi_write+0x1a0/0x2cc
</snip>
On a page boundary limit the number of bytes copied from the tx buffer
to remain within the page.
This patch uses a temporary buffer to hold the 4 bytes to write and then
copies only the bytes required from the tx buffer.
PAGE_READ is used by RISC-V arch code included through mm headers,
and it makes sense to bring in a prefix on these in the driver.
drivers/mtd/nand/raw/qcom_nandc.c:153: warning: "PAGE_READ" redefined
#define PAGE_READ 0x2
In file included from include/linux/memremap.h:7,
from include/linux/mm.h:27,
from include/linux/scatterlist.h:8,
from include/linux/dma-mapping.h:11,
from drivers/mtd/nand/raw/qcom_nandc.c:17:
arch/riscv/include/asm/pgtable.h:48: note: this is the location of the previous definition
Commit 3edfb7bd76bd ("gpiolib: Show correct direction from the
beginning") fixed an existing issue but broke libgpiod tests by
changing the default direction of dummy lines to output.
We don't break user-space so make gpio-mockup behave as before.
UBSAN: Undefined behavior in
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c:626:29
signed integer overflow: 1802201963 + 1802201963 cannot be represented
in type 'int'
The union of res_reserved and res_port_rsvd[MLX4_MAX_PORTS] monitors
granting of reserved resources. The grant operation is calculated and
protected, thus both members of the union cannot be negative. Changed
type of res_reserved and of res_port_rsvd[MLX4_MAX_PORTS] from signed
int to unsigned int, allowing large value.
Fixes: 5a0d0a6161ae ("mlx4: Structures and init/teardown for VF resource quotas") Signed-off-by: Aya Levin <ayal@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When re-registering a user mr, the mpt information for the
existing mr when running SRIOV is obtained via the QUERY_MPT
fw command. The returned information includes the mpt's lkey.
This retrieved mpt information is used to move the mpt back
to hardware ownership in the rereg flow (via the SW2HW_MPT
fw command when running SRIOV).
The fw API spec states that for SW2HW_MPT, the lkey field
must be zero. Any ConnectX-3 PF driver which checks for strict spec
adherence will return failure for SW2HW_MPT if the lkey field is not
zero (although the fw in practice ignores this field for SW2HW_MPT).
Thus, in order to conform to the fw API spec, set the lkey field to zero
before invoking SW2HW_MPT when running SRIOV.
Fixes: e630664c8383 ("mlx4_core: Add helper functions to support MR re-registration") Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Driver assigns DMAE channel 0 for FW as part of START_RAMROD command. FW
uses this channel for DMAE operations (e.g., TIME_SYNC implementation).
Driver also uses the same channel 0 for DMAE operations for some of the PFs
(e.g., PF0 on Port0). This could lead to concurrent access to the DMAE
channel by FW and driver which is not legal. Hence need to assign unique
DMAE id for FW.
Currently following DMAE channels are used by the clients,
MFW - OCBB/OCSD functionality uses DMAE channel 14/15
Driver 0-3 and 8-11 (for PF dmae operations)
4 and 12 (for stats requests)
Assigning unique dmae_id '13' to the FW.
Changes from previous version:
------------------------------
v2: Incorporated the review comments.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com> Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This register should have been programmed with the physical address
of the memory location containing the shadow tail pointer for
the guest virtual APIC log instead of the base address.
The complete size ("total_size") of the fragmented packet is stored in the
fragment header and in the size of the fragment chain. When the fragments
are ready for merge, the skbuff's tail of the first fragment is expanded to
have enough room after the data pointer for at least total_size. This means
that it gets expanded by total_size - first_skb->len.
But this is ignoring the fact that after expanding the buffer, the fragment
header is pulled by from this buffer. Assuming that the tailroom of the
buffer was already 0, the buffer after the data pointer of the skbuff is
now only total_size - len(fragment_header) large. When the merge function
is then processing the remaining fragments, the code to copy the data over
to the merged skbuff will cause an skb_over_panic when it tries to actually
put enough data to fill the total_size bytes of the packet.
The size of the skb_pull must therefore also be taken into account when the
buffer's tailroom is expanded.
Fixes: 610bfc6bc99b ("batman-adv: Receive fragmented packets and merge") Reported-by: Martin Weinelt <martin@darmstadt.freifunk.net> Co-authored-by: Linus Lüssing <linus.luessing@c0d3.blue> Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The announcement messages of batman-adv COMPAT_VERSION 15 have the
possibility to announce additional information via a dynamic TVLV part.
This part is optional for the ELP packets and currently not parsed by the
Linux implementation. Still out-of-tree versions are using it to transport
things like neighbor hashes to optimize the rebroadcast behavior.
Since the ELP broadcast packets are smaller than the minimal ethernet
packet, it often has to be padded. This is often done (as specified in
RFC894) with octets of zero and thus work perfectly fine with the TVLV
part (making it a zero length and thus empty). But not all ethernet
compatible hardware seems to follow this advice. To avoid ambiguous
situations when parsing the TVLV header, just force the 4 bytes (TVLV
length + padding) after the required ELP header to zero.
The Motorola/Zebra Symbol DS4308-HD is a handheld USB barcode scanner
which does not have a battery, but reports one anyway that always has
capacity 2.
Let's apply the IGNORE quirk to prevent it from being treated like a
power supply so that userspaces don't get confused that this
accessory is almost out of power and warn the user that they need to charge
their wired barcode scanner.
In the case where eq->fw->size > PAGE_SIZE the error return rc
is being set to EINVAL however this is being overwritten to
rc = req->fw->size because the error exit path via label 'out' is
not being taken. Fix this by adding the jump to the error exit
path 'out'.
Detected by CoverityScan, CID#1453465 ("Unused value")
Fixes: c92316bf8e94 ("test_firmware: add batched firmware tests") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Assigning 2 to "renesas,can-clock-select" tricks the driver into
registering the CAN interface, even though we don't want that.
This patch improves one of the checks to prevent that from happening.
Fixes: 862e2b6af9413b43 ("can: rcar_can: support all input clocks") Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com> Signed-off-by: Chris Paterson <Chris.Paterson2@renesas.com> Reviewed-by: Simon Horman <horms+renesas@verge.net.au> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Previous commit /adding/ support for 160 MHz chanspecs was incomplete.
It didn't set bandwidth info and didn't extract control channel info. As
the result it was also using uninitialized "sb" var.
This change has been tested for two chanspecs found to be reported by
some devices/firmwares:
1) 60/160 (0xee32)
Before: chnum:50 control_ch_num:36
After: chnum:50 control_ch_num:60
2) 120/160 (0xed72)
Before: chnum:114 control_ch_num:100
After: chnum:114 control_ch_num:120
Fixes: 330994e8e8ec ("brcmfmac: fix for proper support of 160MHz bandwidth") Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
While there are issues related to object lifetime management, unregister the
media device first when the driver is being unbound. This is slightly
safer.
Since f44ac12f1dcc, BG enablement is tracked with the LPFC_SLI3_BG_ENABLED
bit, which is set in lpfc_get_cfgparam before lpfc_sli_config_sli_port() is
called. The bit shouldn't be cleared before checking the feature. Based on
problem analysis by David Bond.
Fixes: f44ac12f1dcc "scsi: lpfc: Memory allocation error during driver start-up on power8" Tested-by: David Bond <dbond@suse.com> Signed-off-by: Martin Wilck <mwilck@suse.com> Cc: stable@vger.kernel.org # 4.17.x Cc: stable@vger.kernel.org # 4.18.x Cc: stable@vger.kernel.org # 4.19.x Reviewed-by: Hannes Reinecke <hare@suse.com> Acked-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Since Linux 4.17, calls to drm_crtc_vblank_on/off are mandatory, and we get
a warning when ctrc is disabled :
" driver forgot to call drm_crtc_vblank_off()"
But, the vsync IRQ was not totally disabled due the transient hardware
state and specific interrupt line, thus adding proper IRQ masking from
the HHI system control registers.
The last change fixes a race condition introduced by calling the added
drm_crtc_vblank_on/off when an HPD event occurs from the HDMI connector,
triggering a WARN_ON() in the _atomic_begin() callback when the CRTC
is disabled, thus also triggering a WARN_ON() in drm_vblank_put() :
The issue is that vblank need to be enabled in any occurrence of :
- atomic_enable()
- atomic_begin() and state->enable == true, which was not the case
Moving the CRTC enable code to a common function and calling in one of
these occurrence solves this race condition and makes sure vblank is
enabled in each call to _atomic_begin() from the HPD event leading to
drm_atomic_helper_commit_planes().
To Summarize :
- Make sure that the CRTC code will call the drm_crtc_vblank_on()/off()
- *Really* mask the Vsync IRQ
- Initialize and enable vblank at the first
atomic_begin()/_atomic_enable()
Cc: stable@vger.kernel.org # 4.17+ Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Lyude Paul <lyude@redhat.com>
[fixed typos+added cc for stable] Signed-off-by: Lyude Paul <lyude@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/20181122160103.10993-1-narmstrong@baylibre.com Signed-off-by: Sean Paul <seanpaul@chromium.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The tracefs file set_graph_function is used to only function graph functions
that are listed in that file (or all functions if the file is empty). The
way this is implemented is that the function graph tracer looks at every
function, and if the current depth is zero and the function matches
something in the file then it will trace that function. When other functions
are called, the depth will be greater than zero (because the original
function will be at depth zero), and all functions will be traced where the
depth is greater than zero.
The issue is that when a function is first entered, and the handler that
checks this logic is called, the depth is set to zero. If an interrupt comes
in and a function in the interrupt handler is traced, its depth will be
greater than zero and it will automatically be traced, even if the original
function was not. But because the logic only looks at depth it may trace
interrupts when it should not be.
The recent design change of the function graph tracer to fix other bugs
caused the depth to be zero while the function graph callback handler is
being called for a longer time, widening the race of this happening. This
bug was actually there for a longer time, but because the race window was so
small it seldom happened. The Fixes tag below is for the commit that widen
the race window, because that commit belongs to a series that will also help
fix the original bug.
Cc: stable@kernel.org Fixes: 39eb456dacb5 ("function_graph: Use new curr_ret_depth to manage depth instead of curr_ret_stack") Reported-by: Joe Lawrence <joe.lawrence@redhat.com> Tested-by: Joe Lawrence <joe.lawrence@redhat.com> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
commit 3f5fe9fef5b2 ("sched/debug: Fix task state recording/printout")
tried to fix the problem introduced by a previous commit efb40f588b43
("sched/tracing: Fix trace_sched_switch task-state printing"). However
the prev_state output in sched_switch is still broken.
task_state_index() uses fls() which considers the LSB as 1. Left
shifting 1 by this value gives an incorrect mapping to the task state.
Fix this by decrementing the value returned by __get_task_state()
before shifting.
Since commit 4378a7d4be30 ("arm64: implement syscall wrappers")
introduced "__arm64_" prefix to all syscall wrapper symbols in
sys_call_table, syscall tracer can not find corresponding
metadata from syscall name. In the result, we have no syscall
ftrace events on arm64 kernel, and some bpf testcases are failed
on arm64.
To fix this issue, this introduces custom
arch_syscall_match_sym_name() which skips first 8 bytes when
comparing the syscall and symbol names.
net/tipc/topsrv.c: In function ‘tipc_topsrv_start’:
net/tipc/topsrv.c:660:2: warning: ‘strncpy’ specified bound depends on the length of the source argument [-Wstringop-overflow=]
strncpy(srv->name, name, strlen(name) + 1);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
net/tipc/topsrv.c:660:27: note: length computed here
strncpy(srv->name, name, strlen(name) + 1);
^~~~~~~~~~~~
So change it to correct length and use strscpy.
Signed-off-by: Guoqing Jiang <gqjiang@suse.com> Acked-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
passing the strlen() of the source string as the destination
length is pointless, and gcc-8 now warns about it:
drivers/net/ethernet/qlogic/qed/qed_debug.c: In function 'qed_grc_dump':
include/linux/string.h:253: error: 'strncpy' specified bound depends on the length of the source argument [-Werror=stringop-overflow=]
This changes qed_grc_dump_big_ram() to instead uses the length of
the destination buffer, and use strscpy() to guarantee nul-termination.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The problem is caused by the nr_indirectly_reclaimable counter,
which is hidden from the /proc/vmstat, but not from the
/proc/zoneinfo. Let's fix this inconsistency and hide the
counter from /proc/zoneinfo exactly as from /proc/vmstat.
BTW, in 4.19+ the counter has been renamed and exported by
the commit b29940c1abd7 ("mm: rename and change semantics of
nr_indirectly_reclaimable_bytes"), so there is no such a problem
anymore.
Cc: <stable@vger.kernel.org> # 4.14.x-4.18.x Fixes: 7aaf77272358 ("mm: don't show nr_indirectly_reclaimable in /proc/vmstat") Reported-by: Yongqin Liu <yongqin.liu@linaro.org> Signed-off-by: Roman Gushchin <guro@fb.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Commit bb475230b8e5 ("reset: make optional functions really optional")
gave a new meaning to _get_optional variants.
The differentiation by WARN_ON() is not needed any more. We already
have inconsistency about this; (devm_)reset_control_get_exclusive()
has WARN_ON() check, but of_reset_control_get_exclusive() does not.
Commit bb475230b8e5 ("reset: make optional functions really optional")
converted *_get_optional* functions, but device_reset_optional() was
left behind. Convert it in the same way.
By default NFSv3 doesn't support ACL (Access Control Lists)
which might be quite convenient to have so that
mounted NFS behaves exactly as any other local file-system.
In particular missing support of ACL makes umask useless.
This among other thigs fixes Glibc's "nptl/tst-umask1".
Change the default defconfig (used with 'make defconfig') to the ARCv2
nsim_hs_defconfig, and also switch the default Kconfig ISA selection to
ARCv2.
This allows several default defconfigs (e.g. make defconfig, make
allnoconfig, make tinyconfig) to all work with ARCv2 by default.
Note since we change default architecture from ARCompact to ARCv2
it's required to explicitly mention architecture type in ARCompact
defconfigs otherwise ARCv2 will be implied and binaries will be
generated for ARCv2.
[BUG]
A completely valid btrfs will refuse to mount, with error message like:
BTRFS critical (device sdb2): corrupt leaf: root=2 block=239681536 slot=172 \
bg_start=12018974720 bg_len=10888413184, invalid block group size, \
have 10888413184 expect (0, 10737418240]
This has been reported several times as the 4.19 kernel is now being
used. The filesystem refuses to mount, but is otherwise ok and booting
4.18 is a workaround.
Btrfs check returns no error, and all kernels used on this fs is later
than 2011, which should all have the 10G size limit commit.
[CAUSE]
For a 12 devices btrfs, we could allocate a chunk larger than 10G due to
stripe stripe bump up.
The cros_ec_keyb_bs array lists buttons and switches together, expecting
that its users will match the appropriate type and bit fields. But
cros_ec_keyb_register_bs() only checks the 'bit' field, which causes
misreported input capabilities in some cases. For example, tablets
(e.g., Scarlet -- a.k.a. Acer Chromebook Tab 10) were reporting a SW_LID
capability, because EC_MKBP_POWER_BUTTON and EC_MKBP_LID_OPEN happen to
share the same bit.
(This has comedic effect on a tablet, in which a power-management daemon
then thinks this "lid" is closed, and so puts the system to sleep as
soon as it boots!)
To fix this, check both the 'ev_type' and 'bit' fields before reporting
the capability.
Tested with a lid (Kevin / Samsung Chromebook Plus) and without a lid
(Scarlet / Acer Chromebook Tab 10).
This error got introduced when porting the feature from the downstream
Chromium OS kernel to be upstreamed.
"of_get_named_gpio()" returns a negative error value if it fails
and drivers should check for this. This missing check was now
added to the matrix_keypad driver.
In my case "of_get_named_gpio()" returned -EPROBE_DEFER because
the referenced GPIOs belong to an I/O expander, which was not yet
probed at the point in time when the matrix_keypad driver was
loading. Because the driver did not check for errors from the
"of_get_named_gpio()" routine, it was assuming that "-EPROBE_DEFER"
is actually a GPIO number and continued as usual, which led to further
errors like this later on:
Note that the "GPIO number" -517 in the error message above is
actually "-EPROBE_DEFER".
As part of the patch a misleading error message "no platform data defined"
was also removed. This does not lead to information loss because the other
error paths in matrix_keypad_parse_dt() already print an error.
Signed-off-by: Christian Hoff <christian_hoff@gmx.net> Suggested-by: Sebastian Reichel <sre@kernel.org> Reviewed-by: Sebastian Reichel <sre@kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Noticed the other day the trackpoint felt different on my P50, then
realized it was because rmi4 wasn't loading for this machine
automatically. Suspend/resume, hibernate, and everything else seem to
work perfectly fine on here.
Use the new of_get_compatible_child() helper to lookup the legacy
pwrlevels child node instead of using of_find_compatible_node(), which
searches the entire tree from a given start node and thus can return an
unrelated (i.e. non-child) node.
This also addresses a potential use-after-free (e.g. after probe
deferral) as the tree-wide helper drops a reference to its first
argument (i.e. the probed device's node).
While at it, also fix the related child-node reference leak.
Fixes: e2af8b6b0ca1 ("drm/msm: gpu: Use OPP tables if we can") Cc: stable <stable@vger.kernel.org> # 4.12 Cc: Jordan Crouse <jcrouse@codeaurora.org> Cc: Rob Clark <robdclark@gmail.com> Cc: David Airlie <airlied@linux.ie> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Rob Herring <robh@kernel.org>
[ johan: backport to 4.14 ] Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
There is a race condition when accessing kvm->arch.apic_access_page_done.
Due to it, x86_set_memory_region will fail when creating the second vcpu
for a svm guest.
Add a mutex_lock to serialize the accesses to apic_access_page_done.
This lock is also used by vmx for the same purpose.
After 2dd453168643 ("kgdboc: Fix restrict error"), kgdboc_option_setup is
now only used when built in, resulting in a warning when compiled as a
module:
drivers/tty/serial/kgdboc.c:134:12: warning: 'kgdboc_option_setup' defined but not used [-Wunused-function]
static int kgdboc_option_setup(char *opt)
^~~~~~~~~~~~~~~~~~~
Move the function under the appropriate ifdef for builtin only.
Fixes: 2dd453168643 ("kgdboc: Fix restrict error") Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Laura Abbott <labbott@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
drivers/tty/serial/kgdboc.c: In function ‘configure_kgdboc’:
drivers/tty/serial/kgdboc.c:137:2: error: ‘strcpy’ source argument is the same
as destination [-Werror=restrict]
strcpy(config, opt);
^~~~~~~~~~~~~~~~~~~
As the error implies, this is from trying to use config as both source and
destination. Drop the call to the function where config is the argument
since nothing else happens in the function.
Signed-off-by: Laura Abbott <labbott@redhat.com> Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The meddlesome gcc warns about the possible shortname string in
trident driver code:
sound/pci/trident/trident.c: In function ‘snd_trident_probe’:
sound/pci/trident/trident.c:126:2: warning: ‘strcat’ accessing 17 or more bytes at offsets 36 and 20 may overlap 1 byte at offset 36 [-Wrestrict]
strcat(card->shortname, card->driver);
It happens since gcc calculates the possible string size from
card->driver, but this can't be true since we did set the string just
before that, and they are much shorter.
For shutting it up, use the exactly same string set to card->driver
for strcat() to card->shortname, too.
Currently on driver bringup with KASAN enabled, meson triggers an OOB
memory access as shown below:
[ 117.904528] ==================================================================
[ 117.904560] BUG: KASAN: global-out-of-bounds in meson_viu_set_osd_lut+0x7a0/0x890
[ 117.904588] Read of size 4 at addr ffff20000a63ce24 by task systemd-udevd/498
[ 117.904601]
[ 118.083372] CPU: 4 PID: 498 Comm: systemd-udevd Not tainted 4.20.0-rc3Lyude-Test+ #20
[ 118.091143] Hardware name: amlogic khadas-vim2/khadas-vim2, BIOS 2018.07-rc2-armbian 09/11/2018
[ 118.099768] Call trace:
[ 118.102181] dump_backtrace+0x0/0x3e8
[ 118.105796] show_stack+0x14/0x20
[ 118.109083] dump_stack+0x130/0x1c4
[ 118.112539] print_address_description+0x60/0x25c
[ 118.117214] kasan_report+0x1b4/0x368
[ 118.120851] __asan_report_load4_noabort+0x18/0x20
[ 118.125566] meson_viu_set_osd_lut+0x7a0/0x890
[ 118.129953] meson_viu_init+0x10c/0x290
[ 118.133741] meson_drv_bind_master+0x474/0x748
[ 118.138141] meson_drv_bind+0x10/0x18
[ 118.141760] try_to_bring_up_master+0x3d8/0x768
[ 118.146249] component_add+0x214/0x570
[ 118.149978] meson_dw_hdmi_probe+0x18/0x20 [meson_dw_hdmi]
[ 118.155404] platform_drv_probe+0x98/0x138
[ 118.159455] really_probe+0x2a0/0xa70
[ 118.163070] driver_probe_device+0x1b4/0x2d8
[ 118.167299] __driver_attach+0x200/0x280
[ 118.171189] bus_for_each_dev+0x10c/0x1a8
[ 118.175144] driver_attach+0x38/0x50
[ 118.178681] bus_add_driver+0x330/0x608
[ 118.182471] driver_register+0x140/0x388
[ 118.186361] __platform_driver_register+0xc8/0x108
[ 118.191117] meson_dw_hdmi_platform_driver_init+0x1c/0x1000 [meson_dw_hdmi]
[ 118.198022] do_one_initcall+0x12c/0x3bc
[ 118.201883] do_init_module+0x1fc/0x638
[ 118.205673] load_module+0x4b4c/0x6808
[ 118.209387] __se_sys_init_module+0x2e8/0x3c0
[ 118.213699] __arm64_sys_init_module+0x68/0x98
[ 118.218100] el0_svc_common+0x104/0x210
[ 118.221893] el0_svc_handler+0x48/0xb8
[ 118.225594] el0_svc+0x8/0xc
[ 118.228429]
[ 118.229887] The buggy address belongs to the variable:
[ 118.235007] eotf_33_linear_mapping+0x84/0xc0
[ 118.239301]
[ 118.240752] Memory state around the buggy address:
[ 118.245522] ffff20000a63cd00: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 118.252695] ffff20000a63cd80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 118.259850] >ffff20000a63ce00: 00 00 00 00 04 fa fa fa fa fa fa fa 00 00 00 00
[ 118.267000] ^
[ 118.271222] ffff20000a63ce80: 00 fa fa fa fa fa fa fa 00 00 00 00 00 00 00 00
[ 118.278393] ffff20000a63cf00: 00 00 00 00 00 00 00 00 00 00 00 00 04 fa fa fa
[ 118.285542] ==================================================================
[ 118.292699] Disabling lock debugging due to kernel taint
It seems that when looping through the OSD EOTF LUT maps, we use the
same max iterator for OETF: 20. This is wrong though, since 20*2 is 40,
which means that we'll stop out of bounds on the EOTF maps.
But, this whole thing is already confusing enough to read through as-is,
so let's just replace all of the hardcoded sizes with
OSD_(OETF/EOTF)_LUT_SIZE / 2.
Signed-off-by: Lyude Paul <lyude@redhat.com> Fixes: bbbe775ec5b5 ("drm: Add support for Amlogic Meson Graphic Controller") Cc: Neil Armstrong <narmstrong@baylibre.com> Cc: Maxime Ripard <maxime.ripard@bootlin.com> Cc: Carlo Caione <carlo@caione.org> Cc: Kevin Hilman <khilman@baylibre.com> Cc: dri-devel@lists.freedesktop.org Cc: linux-amlogic@lists.infradead.org Cc: linux-arm-kernel@lists.infradead.org Cc: <stable@vger.kernel.org> # v4.10+ Acked-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://patchwork.freedesktop.org/patch/msgid/20181125012117.31915-1-lyude@redhat.com Signed-off-by: Sean Paul <seanpaul@chromium.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Seeing as we use this registermap in the context of our IRQ handlers, we
need to be using spinlocks for reading/writing registers so that we can
still read them from IRQ handlers without having to grab any mutexes and
accidentally sleep. We don't currently do this, as pointed out by
lockdep:
When drm_new_set_master() fails, set is_master to 0, to prevent a
possible NULL pointer deref.
Here is a problematic flow: we check is_master in drm_is_current_master(),
then proceed to call drm_lease_owner() passing master. If we do not restore
is_master status when drm_new_set_master() fails, we may have a situation
in which is_master will be 1 and master itself, NULL, leading to the deref
of a NULL pointer in drm_lease_owner().
This fixes the following OOPS, observed on an ArchLinux running a 4.19.2
kernel:
If the platform has no IO space, ioregs is placed next to the already
allocated regs. In this case, it should not be separately freed.
This prevents a kernel warning from __vunmap "Trying to vfree()
nonexistent vm area" when unloading the driver.
Fixes: 0dd68309b9c5 ("drm/ast: Try to use MMIO registers when PIO isn't supported") Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com> Cc: <stable@vger.kernel.org> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If the firmware reports a connection width that is not 1x, 4x, 8x or 12x
it causes the driver to fail during initialization.
To prevent this failure every time a new width is introduced to the RDMA
stack, we will set a default 4x width for these widths which ar unknown to
the driver.
This is needed to allow to run old kernels with new firmware.
Cc: <stable@vger.kernel.org> # 4.1 Fixes: 1b5daf11b015 ("IB/mlx5: Avoid using the MAD_IFC command under ISSI > 0 mode") Signed-off-by: Michael Guralnik <michaelgur@mellanox.com> Reviewed-by: Majd Dibbiny <majd@mellanox.com> Signed-off-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In case the nd_sd group is set to the sd-card function, Pins 45 + 46 are
configured as GPIOs. If they are blocked by the sd function, they can't
be used as GPIOs.
Reported-by: Kristian Evensen <kristian.evensen@gmail.com> Signed-off-by: Mathias Kresin <dev@kresin.me> Signed-off-by: Paul Burton <paul.burton@mips.com> Fixes: f576fb6a0700 ("MIPS: ralink: cleanup the soc specific pinmux data")
Patchwork: https://patchwork.linux-mips.org/patch/21220/ Cc: John Crispin <john@phrozen.org> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: James Hogan <jhogan@kernel.org> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Cc: stable@vger.kernel.org # v3.18+ Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
142b18ddc8143 ("uprobes: Fix handle_swbp() vs unregister() + register() race")
added the UPROBE_COPY_INSN flag, and corresponding smp_wmb() and smp_rmb()
memory barriers, to ensure that handle_swbp() uses fully-initialized
uprobes only.
However, the smp_rmb() is mis-placed: this barrier should be placed
after handle_swbp() has tested for the flag, thus guaranteeing that
(program-order) subsequent loads from the uprobe can see the initial
stores performed by prepare_uprobe().
Move the smp_rmb() accordingly. Also amend the comments associated
to the two memory barriers to indicate their actual locations.
Signed-off-by: Andrea Parri <andrea.parri@amarulasolutions.com> Acked-by: Oleg Nesterov <oleg@redhat.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Vince Weaver <vincent.weaver@maine.edu> Cc: stable@kernel.org Fixes: 142b18ddc8143 ("uprobes: Fix handle_swbp() vs unregister() + register() race") Link: http://lkml.kernel.org/r/20181122161031.15179-1-andrea.parri@amarulasolutions.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If for some reason we failed to query the mr status, we need to make sure
to provide sufficient information for an ambiguous error (guard error on
sector 0).
gcc discovered that the memcpy() arguments in kdbnearsym() overlap, so
we should really use memmove(), which is defined to handle that correctly:
In function 'memcpy',
inlined from 'kdbnearsym' at /git/arm-soc/kernel/debug/kdb/kdb_support.c:132:4:
/git/arm-soc/include/linux/string.h:353:9: error: '__builtin_memcpy' accessing 792 bytes at offsets 0 and 8 overlaps 784 bytes at offset 8 [-Werror=restrict]
return __builtin_memcpy(p, q, size);
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Jason Wessel <jason.wessel@windriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The bfa driver has a number of real issues with string termination
that gcc-8 now points out:
drivers/scsi/bfa/bfad_bsg.c: In function 'bfad_iocmd_port_get_attr':
drivers/scsi/bfa/bfad_bsg.c:320:9: error: argument to 'sizeof' in 'strncpy' call is the same expression as the source; did you mean to use the size of the destination? [-Werror=sizeof-pointer-memaccess]
drivers/scsi/bfa/bfa_fcs.c: In function 'bfa_fcs_fabric_psymb_init':
drivers/scsi/bfa/bfa_fcs.c:775:9: error: argument to 'sizeof' in 'strncat' call is the same expression as the source; did you mean to use the size of the destination? [-Werror=sizeof-pointer-memaccess]
drivers/scsi/bfa/bfa_fcs.c:781:9: error: argument to 'sizeof' in 'strncat' call is the same expression as the source; did you mean to use the size of the destination? [-Werror=sizeof-pointer-memaccess]
drivers/scsi/bfa/bfa_fcs.c:788:9: error: argument to 'sizeof' in 'strncat' call is the same expression as the source; did you mean to use the size of the destination? [-Werror=sizeof-pointer-memaccess]
drivers/scsi/bfa/bfa_fcs.c:801:10: error: argument to 'sizeof' in 'strncat' call is the same expression as the source; did you mean to use the size of the destination? [-Werror=sizeof-pointer-memaccess]
drivers/scsi/bfa/bfa_fcs.c:808:10: error: argument to 'sizeof' in 'strncat' call is the same expression as the source; did you mean to use the size of the destination? [-Werror=sizeof-pointer-memaccess]
drivers/scsi/bfa/bfa_fcs.c: In function 'bfa_fcs_fabric_nsymb_init':
drivers/scsi/bfa/bfa_fcs.c:837:10: error: argument to 'sizeof' in 'strncat' call is the same expression as the source; did you mean to use the size of the destination? [-Werror=sizeof-pointer-memaccess]
drivers/scsi/bfa/bfa_fcs.c:844:10: error: argument to 'sizeof' in 'strncat' call is the same expression as the source; did you mean to use the size of the destination? [-Werror=sizeof-pointer-memaccess]
drivers/scsi/bfa/bfa_fcs.c:852:10: error: argument to 'sizeof' in 'strncat' call is the same expression as the source; did you mean to use the size of the destination? [-Werror=sizeof-pointer-memaccess]
drivers/scsi/bfa/bfa_fcs.c: In function 'bfa_fcs_fabric_psymb_init':
drivers/scsi/bfa/bfa_fcs.c:778:2: error: 'strncat' output may be truncated copying 10 bytes from a string of length 63 [-Werror=stringop-truncation]
drivers/scsi/bfa/bfa_fcs.c:784:2: error: 'strncat' output may be truncated copying 30 bytes from a string of length 63 [-Werror=stringop-truncation]
drivers/scsi/bfa/bfa_fcs.c:803:3: error: 'strncat' output may be truncated copying 44 bytes from a string of length 63 [-Werror=stringop-truncation]
drivers/scsi/bfa/bfa_fcs.c:811:3: error: 'strncat' output may be truncated copying 16 bytes from a string of length 63 [-Werror=stringop-truncation]
drivers/scsi/bfa/bfa_fcs.c: In function 'bfa_fcs_fabric_nsymb_init':
drivers/scsi/bfa/bfa_fcs.c:840:2: error: 'strncat' output may be truncated copying 10 bytes from a string of length 63 [-Werror=stringop-truncation]
drivers/scsi/bfa/bfa_fcs.c:847:2: error: 'strncat' output may be truncated copying 30 bytes from a string of length 63 [-Werror=stringop-truncation]
drivers/scsi/bfa/bfa_fcs_lport.c: In function 'bfa_fcs_fdmi_get_hbaattr':
drivers/scsi/bfa/bfa_fcs_lport.c:2657:10: error: argument to 'sizeof' in 'strncat' call is the same expression as the source; did you mean to use the size of the destination? [-Werror=sizeof-pointer-memaccess]
drivers/scsi/bfa/bfa_fcs_lport.c:2659:11: error: argument to 'sizeof' in 'strncat' call is the same expression as the source; did you mean to use the size of the destination? [-Werror=sizeof-pointer-memaccess]
drivers/scsi/bfa/bfa_fcs_lport.c: In function 'bfa_fcs_lport_ms_gmal_response':
drivers/scsi/bfa/bfa_fcs_lport.c:3232:5: error: 'strncpy' output may be truncated copying 16 bytes from a string of length 247 [-Werror=stringop-truncation]
drivers/scsi/bfa/bfa_fcs_lport.c: In function 'bfa_fcs_lport_ns_send_rspn_id':
drivers/scsi/bfa/bfa_fcs_lport.c:4670:3: error: 'strncpy' output truncated before terminating nul copying as many bytes from a string as its length [-Werror=stringop-truncation]
drivers/scsi/bfa/bfa_fcs_lport.c:4682:3: error: 'strncat' output truncated before terminating nul copying as many bytes from a string as its length [-Werror=stringop-truncation]
drivers/scsi/bfa/bfa_fcs_lport.c: In function 'bfa_fcs_lport_ns_util_send_rspn_id':
drivers/scsi/bfa/bfa_fcs_lport.c:5206:3: error: 'strncpy' output truncated before terminating nul copying as many bytes from a string as its length [-Werror=stringop-truncation]
drivers/scsi/bfa/bfa_fcs_lport.c:5215:3: error: 'strncat' output truncated before terminating nul copying as many bytes from a string as its length [-Werror=stringop-truncation]
drivers/scsi/bfa/bfa_fcs_lport.c: In function 'bfa_fcs_fdmi_get_portattr':
drivers/scsi/bfa/bfa_fcs_lport.c:2751:2: error: 'strncpy' specified bound 128 equals destination size [-Werror=stringop-truncation]
drivers/scsi/bfa/bfa_fcbuild.c: In function 'fc_rspnid_build':
drivers/scsi/bfa/bfa_fcbuild.c:1254:2: error: 'strncpy' output truncated before terminating nul copying as many bytes from a string as its length [-Werror=stringop-truncation]
drivers/scsi/bfa/bfa_fcbuild.c:1253:25: note: length computed here
drivers/scsi/bfa/bfa_fcbuild.c: In function 'fc_rsnn_nn_build':
drivers/scsi/bfa/bfa_fcbuild.c:1275:2: error: 'strncpy' output truncated before terminating nul copying as many bytes from a string as its length [-Werror=stringop-truncation]
In most cases, this can be addressed by correctly calling strlcpy and
strlcat instead of strncpy/strncat, with the size of the destination
buffer as the last argument.
For consistency, I'm changing the other callers of strncpy() in this
driver the same way.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Acked-by: Sudarsana Kalluru <Sudarsana.Kalluru@cavium.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
By passing a limit of 2 bytes to strncat, strncat is limited to writing
fewer bytes than what it's supposed to append to the name here.
Since the bounds are checked on the line above this, just remove the string
bounds checks entirely since they're unneeded.
Signed-off-by: Sultan Alsawaf <sultanxda@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
projects / mirror_ubuntu-bionic-kernel.git / log