popcornmix [Wed, 17 Jun 2015 14:44:08 +0000 (15:44 +0100)]
Add Chris Boot's i2c driver
i2c-bcm2708: fixed baudrate
Fixed issue where the wrong CDIV value was set for baudrates below 3815 Hz (for 250MHz bus clock).
In that case the computed CDIV value was more than 0xffff. However the CDIV register width is only 16 bits.
This resulted in incorrect setting of CDIV and higher baudrate than intended.
Example: 3500Hz -> CDIV=0x11704 -> CDIV(16bit)=0x1704 -> 42430Hz
After correction: 3500Hz -> CDIV=0x11704 -> CDIV(16bit)=0xffff -> 3815Hz
The correct baudrate is shown in the log after the cdiv > 0xffff correction.
Perform I2C combined transactions when possible
Perform I2C combined transactions whenever possible, within the
restrictions of the Broadcomm Serial Controller.
Disable DONE interrupt during TA poll
Prevent interrupt from being triggered if poll is missed and transfer
starts and finishes.
i2c: Make combined transactions optional and disabled by default
i2c: bcm2708: add device tree support
Add DT support to driver and add to .dtsi file.
Setup pins in .dts file.
i2c is disabled by default.
Signed-off-by: Noralf Tronnes <notro@tronnes.org>
bcm2708: don't register i2c controllers when using DT
The devices for the i2c controllers are in the Device Tree.
Only register devices when not using DT.
Signed-off-by: Noralf Tronnes <notro@tronnes.org>
I2C: Only register the I2C device for the current board revision
i2c_bcm2708: Fix clock reference counting
Fix grabbing lock from atomic context in i2c driver
2 main changes:
- check for timeouts in the bcm2708_bsc_setup function as indicated by this comment:
/* poll for transfer start bit (should only take 1-20 polls) */
This implies that the setup function can now fail so account for this everywhere it's called
- Removed the clk_get_rate call from inside the setup function as it locks a mutex and that's not ok since we call it from under a spin lock.
i2c-bcm2708: When using DT, leave the GPIO setup to pinctrl
i2c-bcm2708: Increase timeouts to allow larger transfers
Use the timeout value provided by the I2C_TIMEOUT ioctl when waiting
for completion. The default timeout is 1 second.
The third I2C bus (I2C2) is normally reserved for HDMI use. Careless
use of this bus can break an attached display - use with caution.
It is recommended to disable accesses by VideoCore by setting
hdmi_ignore_edid=1 or hdmi_edid_file=1 in config.txt.
The interface is disabled by default - enable using the
i2c2_iknowwhatimdoing DT parameter.
bcm2708-spi: Don't use static pin configuration with DT
Also remove superfluous error checking - the SPI framework ensures the
validity of the chip_select value.
i2c-bcm2708: Remove non-DT support
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Set the BSC_CLKT clock streching timeout to 35ms as per SMBus specs.
Fixes i2c_bcm2708: Write to FIFO correctly - v2 (#1574)
* i2c: fix i2c_bcm2708: Clear FIFO before sending data
Make sure FIFO gets cleared before trying to send
data in case of a repeated start (COMBINED=Y).
* i2c: fix i2c_bcm2708: Only write to FIFO when not full
Check if FIFO can accept data before writing.
To avoid a peripheral read on the last iteration of a loop,
both bcm2708_bsc_fifo_fill and ~drain are changed as well.
Aron Szabo [Sat, 16 Jun 2012 10:15:55 +0000 (12:15 +0200)]
lirc: added support for RaspberryPi GPIO
lirc_rpi: Use read_current_timer to determine transmitter delay. Thanks to jjmz and others
See: https://github.com/raspberrypi/linux/issues/525
lirc: Remove restriction on gpio pins that can be used with lirc
Compute Module, for example could use different pins
lirc_rpi: Add parameter to specify input pin pull
Depending on the connected IR circuitry it might be desirable to change the
gpios internal pull from it pull-down default behaviour. Add a module
parameter to allow the user to set it explicitly.
Signed-off-by: Julian Scheel <julian@jusst.de>
lirc-rpi: Use the higher-level irq control functions
This module used to access the irq_chip methods of the
gpio controller directly, rather than going through the
standard enable_irq/irq_set_irq_type functions. This
caused problems on pinctrl-bcm2835 which only implements
the irq_enable/disable methods and not irq_unmask/mask.
lirc-rpi: Correct the interrupt usage
1) Correct the use of enable_irq (i.e. don't call it so often)
2) Correct the shutdown sequence.
3) Avoid a bcm2708_gpio driver quirk by setting the irq flags earlier
lirc-rpi: use getnstimeofday instead of read_current_timer
read_current_timer isn't guaranteed to return values in
microseconds, and indeed it doesn't on a Pi2.
Issue: linux#827
lirc-rpi: Add device tree support, and a suitable overlay
The overlay supports DT parameters that match the old module
parameters, except that gpio_in_pull should be set using the
strings "up", "down" or "off".
lirc-rpi: Also support pinctrl-bcm2835 in non-DT mode
fix auto-sense in lirc_rpi driver
On a Raspberry Pi 2, the lirc_rpi driver might receive spurious
interrupts and change it's low-active / high-active setting.
When this happens, the IR remote control stops working.
This patch disables this auto-detection if the 'sense' parameter
was set in the device tree, making the driver robust to such
spurious interrupts.
Tim Gover [Tue, 22 Jul 2014 14:41:04 +0000 (15:41 +0100)]
vcsm: VideoCore shared memory service for BCM2835
Add experimental support for the VideoCore shared memory service.
This allows user processes to allocate memory from VideoCore's
GPU relocatable heap and mmap the buffers. Additionally, the memory
handles can passed to other VideoCore services such as MMAL, OpenMax
and DispmanX
TODO
* This driver was originally released for BCM28155 which has a different
cache architecture to BCM2835. Consequently, in this release only
uncached mappings are supported. However, there's no fundamental
reason which cached mappings cannot be support or BCM2835
* More refactoring is required to remove the typedefs.
* Re-enable the some of the commented out debug-fs statistics which were
disabled when migrating code from proc-fs.
* There's a lot of code to support sharing of VCSM in order to support
Android. This could probably done more cleanly or perhaps just
removed.
Signed-off-by: Tim Gover <timgover@gmail.com>
config: Disable VC_SM for now to fix hang with cutdown kernel
vcsm: Use boolean as it cannot be built as module
On building the bcm_vc_sm as a module we get the following error:
v7_dma_flush_range and do_munmap are undefined in vc-sm.ko.
popcornmix [Mon, 26 Mar 2012 21:15:50 +0000 (22:15 +0100)]
bcm2708: alsa sound driver
Signed-off-by: popcornmix <popcornmix@gmail.com>
alsa: add mmap support and some cleanups to bcm2835 ALSA driver
snd-bcm2835: Add support for spdif/hdmi passthrough
This adds a dedicated subdevice which can be used for passthrough of non-audio
formats (ie encoded a52) through the hdmi audio link. In addition to this
driver extension an appropriate card config is required to make alsa-lib
support the AES parameters for this device.
snd-bcm2708: Add mutex, improve logging
Fix for ALSA driver crash
Avoids an issue when closing and opening vchiq where a message can arrive before service handle has been written
alsa: reduce severity of expected warning message
snd-bcm2708: Fix dmesg spam for non-error case
alsa: Ensure mutexes are released through error paths
alsa: Make interrupted close paths quieter
BCM270x: Add onboard sound device to Device Tree
Add Device Tree support to alsa driver.
Add device to Device Tree.
Don't add platform devices when booting in DT mode.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
bcm2835: access controls under the audio mutex
I don't think the ALSA framework provides any kind of automatic
synchronization within the control callbacks. We most likely need
to ensure this manually, so add locking around all access to shared
mutable data. In particular, bcm2835_audio_set_ctls() should
probably always be called under our own audio lock.
snd-bcm2835: Don't allow responses from VC to be interrupted by user signals
There should always be a response, and retry after a signal interruption is not handled, so don't report
we are interruptible.
Phil Elwell [Wed, 11 May 2016 11:50:33 +0000 (12:50 +0100)]
mmc: Add MMC_QUIRK_ERASE_BROKEN for some cards
Some SD cards have been found that corrupt data when small blocks
are erased. Add a quirk to indicate that ERASE should not be used,
and set it for cards of that type.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
mmc: Apply QUIRK_BROKEN_ERASE to other capacities
Use mmc_block.card_quirks to override the quirks for all SD or MMC
cards. The value is a bitfield using the bit positions defined in
include/linux/mmc/card.h. If the module parameter is placed in the
kernel command line (or bootargs) stored on the card then, assuming the
device only has one SD card interface, the override effectively becomes
card-specific.
Phil Elwell [Wed, 25 Mar 2015 17:49:47 +0000 (17:49 +0000)]
Adding bcm2835-sdhost driver, and an overlay to enable it
BCM2835 has two SD card interfaces. This driver uses the other one.
bcm2835-sdhost: Error handling fix, and code clarification
bcm2835-sdhost: Adding overclocking option
Allow a different clock speed to be substitued for a requested 50MHz.
This option is exposed using the "overclock_50" DT parameter.
Note that the sdhost interface is restricted to integer divisions of
core_freq, and the highest sensible option for a core_freq of 250MHz
is 84 (250/3 = 83.3MHz), the next being 125 (250/2) which is much too
high.
Use at your own risk.
bcm2835-sdhost: Round up the overclock, so 62 works for 62.5Mhz
Also only warn once for each overclock setting.
bcm2835-sdhost: Improve error handling and recovery
1) Expose the hw_reset method to the MMC framework, removing many
internal calls by the driver.
2) Reduce overclock setting on error.
3) Increase timeout to cope with high capacity cards.
4) Add properties and parameters to control pio_limit and debug.
5) Reduce messages at probe time.
bcm2835-sdhost: Further improve overclock back-off
It seems that the sdhost interface returns CRC7 errors for CMD1,
which is the MMC-specific SEND_OP_COND. Returning these errors to
the MMC layer causes a downward spiral, but ignoring them seems
to be harmless.
The bcm2835-mmc driver (and -sdhost driver that copied from it)
contains code to handle SDIO interrupts in a threaded interrupt
handler rather than waking the MMC framework thread. The change
follows a patch from Russell King that adds the facility as the
preferred way of working.
However, the new code path is only present in ARCH_BCM2835
builds, which I have taken to be a way of testing the waters
rather than making the change across the board; I can't see
any technical reason why it wouldn't be enabled for MACH_BCM270X
builds. So this patch standardises on the ARCH_BCM2835 code,
removing the old code paths.
The MMC card-discovery process generates timeouts. This is
expected behaviour, so reporting it to the user serves no purpose.
Suppress the reporting of timeout errors unless the debug flag
is on.
bcm2835-sdhost: Add workaround for odd behaviour on some cards
For reasons not understood, the sdhost driver fails when reading
sectors very near the end of some SD cards. The problem could
be related to the similar issue that reading the final sector
of any card as part of a multiple read never completes, and the
workaround is an extension of the mechanism introduced to solve
that problem which ensures those sectors are always read singly.
bcm2835-sdhost: Major revision
This is a significant revision of the bcm2835-sdhost driver. It
improves on the original in a number of ways:
1) Through the use of CMD23 for reads it appears to avoid problems
reading some sectors on certain high speed cards.
2) Better atomicity to prevent crashes.
3) Higher performance.
4) Activity logging included, for easier diagnosis in the event
of a problem.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: Restore ATOMIC flag to PIO sg mapping
Allocation problems have been seen in a wireless driver, and
this is the only change which might have been responsible.
SQUASH: bcm2835-sdhost: Only claim one DMA channel
With both MMC controllers enabled there are few DMA channels left. The
bcm2835-sdhost driver only uses DMA in one direction at a time, so it
doesn't need to claim two channels.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: Workaround for "slow" sectors
Some cards have been seen to cause timeouts after certain sectors are
read. This workaround enforces a minimum delay between the stop after
reading one of those sectors and a subsequent data command.
Using CMD23 (SET_BLOCK_COUNT) avoids this problem, so good cards will
not be penalised by this workaround.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: Firmware manages the clock divisor
The bcm2835-sdhost driver hands control of the CDIV clock divisor
register to matching firmware, allowing it to adjust to a changing
core clock. This removes the need to use the performance governor or
to enable io_is_busy on the on-demand governor in order to get the
best SD performance.
N.B. As SD clocks must be an integer divisor of the core clock, it is
possible that the SD clock for "turbo" mode can be different (even
lower) than "normal" mode.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: Reset the clock in task context
Since reprogramming the clock can now involve a round-trip to the
firmware it must not be done at atomic context, and a tasklet
is not a task.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: Don't exit cmd wait loop on error
The FAIL flag can be set in the CMD register before command processing
is complete, leading to spurious "failed to complete" errors. This has
the effect of promoting harmless CRC7 errors during CMD1 processing
into errors that can delay and even prevent booting.
Also:
1) Convert the last KERN_ERROR message in the register dumping to
KERN_INFO.
2) Remove an unnecessary reset call from bcm2835_sdhost_add_host.
gellert [Fri, 15 Aug 2014 15:35:06 +0000 (16:35 +0100)]
MMC: added alternative MMC driver
mmc: Disable CMD23 transfers on all cards
Pending wire-level investigation of these types of transfers
and associated errors on bcm2835-mmc, disable for now. Fallback of
CMD18/CMD25 transfers will be used automatically by the MMC layer.
Probe error handling is broken in several places.
Simplify error handling by using device managed functions.
Replace pr_{err,info} with dev_{err,info}.
bcm2835-mmc: Add range of debug options for slowing things down
bcm2835-mmc: Add option to disable some delays
bcm2835-mmc: Add option to disable MMC_QUIRK_BLK_NO_CMD23
bcm2835-mmc: Default to disabling MMC_QUIRK_BLK_NO_CMD23
bcm2835-mmc: Adding overclocking option
Allow a different clock speed to be substitued for a requested 50MHz.
This option is exposed using the "overclock_50" DT parameter.
Note that the mmc interface is restricted to EVEN integer divisions of
250MHz, and the highest sensible option is 63 (250/4 = 62.5), the
next being 125 (250/2) which is much too high.
Use at your own risk.
bcm2835-mmc: Round up the overclock, so 62 works for 62.5Mhz
Also only warn once for each overclock setting.
mmc: bcm2835-mmc: Make available on ARCH_BCM2835
Make the bcm2835-mmc driver available for use on ARCH_BCM2835.
bcm2835-mmc: Don't override bus width capabilities from devicetree
Take out the force setting of the MMC_CAP_4_BIT_DATA host capability
so that the result read from devicetree via mmc_of_parse() is
preserved.
bcm2835-mmc: Only claim one DMA channel
With both MMC controllers enabled there are few DMA channels left. The
bcm2835-mmc driver only uses DMA in one direction at a time, so it
doesn't need to claim two channels.
Florian Meier [Fri, 22 Nov 2013 13:22:53 +0000 (14:22 +0100)]
dmaengine: Add support for BCM2708
Add support for DMA controller of BCM2708 as used in the Raspberry Pi.
Currently it only supports cyclic DMA.
Signed-off-by: Florian Meier <florian.meier@koalo.de>
dmaengine: expand functionality by supporting scatter/gather transfers sdhci-bcm2708 and dma.c: fix for LITE channels
DMA: fix cyclic LITE length overflow bug
dmaengine: bcm2708: Remove chancnt affectations
Mirror bcm2835-dma.c commit 9eba5536a7434c69d8c185d4bd1c70734d92287d:
chancnt is already filled by dma_async_device_register, which uses the channel
list to know how much channels there is.
Since it's already filled, we can safely remove it from the drivers' probe
function.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: overwrite dreq only if it is not set
dreq is set when the DMA channel is fetched from Device Tree.
slave_id is set using dmaengine_slave_config().
Only overwrite dreq with slave_id if it is not set.
dreq/slave_id in the cyclic DMA case is not touched, because I don't
have hardware to test with.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: do device registration in the board file
Don't register the device in the driver. Do it in the board file.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: don't restrict DT support to ARCH_BCM2835
Both ARCH_BCM2835 and ARCH_BCM270x are built with OF now.
Add Device Tree support to the non ARCH_BCM2835 case.
Use the same driver name regardless of architecture.
Add Device Tree entry for bcm2835-dma.
The entry doesn't contain any resources since they are handled
by the arch/arm/mach-bcm270x/dma.c driver.
In non-DT mode, don't add the device in the board file.
BCM270x: Add memory and irq resources to dmaengine device and DT
Prepare for merging of the legacy DMA API arch driver dma.c
with bcm2708-dmaengine by adding memory and irq resources both
to platform file device and Device Tree node.
Don't use BCM_DMAMAN_DRIVER_NAME so we don't have to include mach/dma.h
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: Merge with arch dma.c driver and disable dma.c
Merge the legacy DMA API driver with bcm2708-dmaengine.
This is done so we can use bcm2708_fb on ARCH_BCM2835 (mailbox
driver is also needed).
Changes to the dma.c code:
- Use BIT() macro.
- Cutdown some comments to one line.
- Add mutex to vc_dmaman and use this, since the dev lock is locked
during probing of the engine part.
- Add global g_dmaman variable since drvdata is used by the engine part.
- Restructure for readability:
vc_dmaman_chan_alloc()
vc_dmaman_chan_free()
bcm_dma_chan_free()
- Restructure bcm_dma_chan_alloc() to simplify error handling.
- Use device irq resources instead of hardcoded bcm_dma_irqs table.
- Remove dev_dmaman_register() and code it directly.
- Remove dev_dmaman_deregister() and code it directly.
- Simplify bcm_dmaman_probe() using devm_* functions.
- Get dmachans from DT if available.
- Keep 'dma.dmachans' module argument name for backwards compatibility.
Make it available on ARCH_BCM2835 as well.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: set residue_granularity field
bcm2708-dmaengine supports residue reporting at burst level
but didn't report this via the residue_granularity field.
Without this field set properly we get playback issues with I2S cards.
dmaengine: bcm2708-dmaengine: Fix memory leak when stopping a running transfer
bcm2708-dmaengine: Use more DMA channels (but not 12)
1) Only the bcm2708_fb drivers uses the legacy DMA API, and
it requires a BULK-capable channel, so all other types
(FAST, NORMAL and LITE) can be made available to the regular
DMA API.
2) DMA channels 11-14 share an interrupt. The driver can't
handle this, so don't use channels 12-14 (12 was used, probably
because it appears to have an interrupt, but in reality that
interrupt is for activity on ANY channel). This may explain
a lockup encountered when running out of DMA channels.
The combined effect of this patch is to leave 7 DMA channels
available + channel 0 for bcm2708_fb via the legacy API.
dmaengine: bcm2708: Make legacy API available for bcm2835-dma
bcm2708_fb uses the legacy DMA API, so in order to start using
bcm2835-dma, bcm2835-dma has to support the legacy API. Make this
possible by exporting bcm_dmaman_probe() and bcm_dmaman_remove().
popcornmix [Wed, 17 Jun 2015 16:06:34 +0000 (17:06 +0100)]
bcm2708 framebuffer driver
Signed-off-by: popcornmix <popcornmix@gmail.com>
bcm2708_fb : Implement blanking support using the mailbox property interface
bcm2708_fb: Add pan and vsync controls
bcm2708_fb: DMA acceleration for fb_copyarea
Based on http://www.raspberrypi.org/phpBB3/viewtopic.php?p=62425#p62425
Also used Simon's dmaer_master module as a reference for tweaking DMA
settings for better performance.
For now busylooping only. IRQ support might be added later.
With non-overclocked Raspberry Pi, the performance is ~360 MB/s
for simple copy or ~260 MB/s for two-pass copy (used when dragging
windows to the right).
In the case of using DMA channel 0, the performance improves
to ~440 MB/s.
For comparison, VFP optimized CPU copy can only do ~114 MB/s in
the same conditions (hindered by reading uncached source buffer).
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
bcm2708_fb: report number of dma copies
Add a counter (exported via debugfs) reporting the
number of dma copies that the framebuffer driver
has done, in order to help evaluate different
optimization strategies.
Signed-off-by: Luke Diamand <luked@broadcom.com>
bcm2708_fb: use IRQ for DMA copies
The copyarea ioctl() uses DMA to speed things along. This
was busy-waiting for completion. This change supports using
an interrupt instead for larger transfers. For small
transfers, busy-waiting is still likely to be faster.
Signed-off-by: Luke Diamand <luke@diamand.org>
bcm2708: Make ioctl logging quieter
video: fbdev: bcm2708_fb: Don't panic on error
No need to panic the kernel if the video driver fails.
Just print a message and return an error.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
fbdev: bcm2708_fb: Add ARCH_BCM2835 support
Add Device Tree support.
Pass the device to dma_alloc_coherent() in order to get the
correct bus address on ARCH_BCM2835.
Use the new DMA legacy API header file.
Including <mach/platform.h> is not necessary.
Signed-off-by: Kari Suvanto <karis79@gmail.com>
usb: dwc: fix inconsistent lock state
Signed-off-by: Kari Suvanto <karis79@gmail.com>
Add FIQ patch to dwc_otg driver. Enable with dwc_otg.fiq_fix_enable=1. Should give about 10% more ARM performance.
Thanks to Gordon and Costas
Avoid dynamic memory allocation for channel lock in USB driver. Thanks ddv2005.
Add NAK holdoff scheme. Enabled by default, disable with dwc_otg.nak_holdoff_enable=0. Thanks gsh
Make sure we wait for the reset to finish
dwc_otg: fix bug in dwc_otg_hcd.c resulting in silent kernel
memory corruption, escalating to OOPS under high USB load.
dwc_otg: Fix unsafe access of QTD during URB enqueue
In dwc_otg_hcd_urb_enqueue during qtd creation, it was possible that the
transaction could complete almost immediately after the qtd was assigned
to a host channel during URB enqueue, which meant the qtd pointer was no
longer valid having been completed and removed. Usually, this resulted in
an OOPS during URB submission. By predetermining whether transactions
need to be queued or not, this unsafe pointer access is avoided.
This bug was only evident on the Pi model A where a device was attached
that had no periodic endpoints (e.g. USB pendrive or some wlan devices).
If the memory allocation for a dwc_otg_urb failed, the kernel would OOPS
because for some reason a member of the *unallocated* struct was set to
zero. Error handling changed to fail correctly.
dwc_otg: fix potential use-after-free case in interrupt handler
If a transaction had previously aborted, certain interrupts are
enabled to track error counts and reset where necessary. On IN
endpoints the host generates an ACK interrupt near-simultaneously
with completion of transfer. In the case where this transfer had
previously had an error, this results in a use-after-free on
the QTD memory space with a 1-byte length being overwritten to
0x00.
dwc_otg: add handling of SPLIT transaction data toggle errors
Previously a data toggle error on packets from a USB1.1 device behind
a TT would result in the Pi locking up as the driver never handled
the associated interrupt. Patch adds basic retry mechanism and
interrupt acknowledgement to cater for either a chance toggle error or
for devices that have a broken initial toggle state (FT8U232/FT232BM).
dwc_otg: implement tasklet for returning URBs to usbcore hcd layer
The dwc_otg driver interrupt handler for transfer completion will spend
a very long time with interrupts disabled when a URB is completed -
this is because usb_hcd_giveback_urb is called from within the handler
which for a USB device driver with complicated processing (e.g. webcam)
will take an exorbitant amount of time to complete. This results in
missed completion interrupts for other USB packets which lead to them
being dropped due to microframe overruns.
This patch splits returning the URB to the usb hcd layer into a
high-priority tasklet. This will have most benefit for isochronous IN
transfers but will also have incidental benefit where multiple periodic
devices are active at once.
dwc_otg: fix NAK holdoff and allow on split transactions only
This corrects a bug where if a single active non-periodic endpoint
had at least one transaction in its qh, on frnum == MAX_FRNUM the qh
would get skipped and never get queued again. This would result in
a silent device until error detection (automatic or otherwise) would
either reset the device or flush and requeue the URBs.
Additionally the NAK holdoff was enabled for all transactions - this
would potentially stall a HS endpoint for 1ms if a previous error state
enabled this interrupt and the next response was a NAK. Fix so that
only split transactions get held off.
dwc_otg: Call usb_hcd_unlink_urb_from_ep with lock held in completion handler
usb_hcd_unlink_urb_from_ep must be called with the HCD lock held. Calling it
asynchronously in the tasklet was not safe (regression in c4564d4a1a0a9b10d4419e48239f5d99e88d2667).
This change unlinks it from the endpoint prior to queueing it for handling in
the tasklet, and also adds a check to ensure the urb is OK to be unlinked
before doing so.
NULL pointer dereference kernel oopses had been observed in usb_hcd_giveback_urb
when a USB device was unplugged/replugged during data transfer. This effect
was reproduced using automated USB port power control, hundreds of replug
events were performed during active transfers to confirm that the problem was
eliminated.
USB fix using a FIQ to implement split transactions
This commit adds a FIQ implementaion that schedules
the split transactions using a FIQ so we don't get
held off by the interrupt latency of Linux
dwc_otg: fix device attributes and avoid kernel warnings on boot
dcw_otg: avoid logging function that can cause panics
See: https://github.com/raspberrypi/firmware/issues/21
Thanks to cleverca22 for fix
dwc_otg: mask correct interrupts after transaction error recovery
The dwc_otg driver will unmask certain interrupts on a transaction
that previously halted in the error state in order to reset the
QTD error count. The various fine-grained interrupt handlers do not
consider that other interrupts besides themselves were unmasked.
By disabling the two other interrupts only ever enabled in DMA mode
for this purpose, we can avoid unnecessary function calls in the
IRQ handler. This will also prevent an unneccesary FIQ interrupt
from being generated if the FIQ is enabled.
dwc_otg: fiq: prevent FIQ thrash and incorrect state passing to IRQ
In the case of a transaction to a device that had previously aborted
due to an error, several interrupts are enabled to reset the error
count when a device responds. This has the side-effect of making the
FIQ thrash because the hardware will generate multiple instances of
a NAK on an IN bulk/interrupt endpoint and multiple instances of ACK
on an OUT bulk/interrupt endpoint. Make the FIQ mask and clear the
associated interrupts.
Additionally, on non-split transactions make sure that only unmasked
interrupts are cleared. This caused a hard-to-trigger but serious
race condition when you had the combination of an endpoint awaiting
error recovery and a transaction completed on an endpoint - due to
the sequencing and timing of interrupts generated by the dwc_otg core,
it was possible to confuse the IRQ handler.
Fix function tracing
dwc_otg: whitespace cleanup in dwc_otg_urb_enqueue
dwc_otg: prevent OOPSes during device disconnects
The dwc_otg_urb_enqueue function is thread-unsafe. In particular the
access of urb->hcpriv, usb_hcd_link_urb_to_ep, dwc_otg_urb->qtd and
friends does not occur within a critical section and so if a device
was unplugged during activity there was a high chance that the
usbcore hub_thread would try to disable the endpoint with partially-
formed entries in the URB queue. This would result in BUG() or null
pointer dereferences.
Fix so that access of urb->hcpriv, enqueuing to the hardware and
adding to usbcore endpoint URB lists is contained within a single
critical section.
dwc_otg: prevent BUG() in TT allocation if hub address is > 16
A fixed-size array is used to track TT allocation. This was
previously set to 16 which caused a crash because
dwc_otg_hcd_allocate_port would read past the end of the array.
This was hit if a hub was plugged in which enumerated as addr > 16,
due to previous device resets or unplugs.
Also add #ifdef FIQ_DEBUG around hcd->hub_port_alloc[], which grows
to a large size if 128 hub addresses are supported. This field is
for debug only for tracking which frame an allocate happened in.
dwc_otg: make channel halts with unknown state less damaging
If the IRQ received a channel halt interrupt through the FIQ
with no other bits set, the IRQ would not release the host
channel and never complete the URB.
Add catchall handling to treat as a transaction error and retry.
dwc_otg: fiq_split: use TTs with more granularity
This fixes certain issues with split transaction scheduling.
- Isochronous multi-packet OUT transactions now hog the TT until
they are completed - this prevents hubs aborting transactions
if they get a periodic start-split out-of-order
- Don't perform TT allocation on non-periodic endpoints - this
allows simultaneous use of the TT's bulk/control and periodic
transaction buffers
This commit will mainly affect USB audio playback.
dwc_otg: fix potential sleep while atomic during urb enqueue
Fixes a regression introduced with eb1b482a. Kmalloc called from
dwc_otg_hcd_qtd_add / dwc_otg_hcd_qtd_create did not always have
the GPF_ATOMIC flag set. Force this flag when inside the larger
critical section.
dwc_otg: make fiq_split_enable imply fiq_fix_enable
Failing to set up the FIQ correctly would result in
"IRQ 32: nobody cared" errors in dmesg.
dwc_otg: prevent crashes on host port disconnects
Fix several issues resulting in crashes or inconsistent state
if a Model A root port was disconnected.
- Clean up queue heads properly in kill_urbs_in_qh_list by
removing the empty QHs from the schedule lists
- Set the halt status properly to prevent IRQ handlers from
using freed memory
- Add fiq_split related cleanup for saved registers
- Make microframe scheduling reclaim host channels if
active during a disconnect
- Abort URBs with -ESHUTDOWN status response, informing
device drivers so they respond in a more correct fashion
and don't try to resubmit URBs
- Prevent IRQ handlers from attempting to handle channel
interrupts if the associated URB was dequeued (and the
driver state was cleared)
dwc_otg: prevent leaking URBs during enqueue
A dwc_otg_urb would get leaked if the HCD enqueue function
failed for any reason. Free the URB at the appropriate points.
dwc_otg: Enable NAK holdoff for control split transactions
Certain low-speed devices take a very long time to complete a
data or status stage of a control transaction, producing NAK
responses until they complete internal processing - the USB2.0
spec limit is up to 500mS. This causes the same type of interrupt
storm as seen with USB-serial dongles prior to c8edb238.
In certain circumstances, usually while booting, this interrupt
storm could cause SD card timeouts.
dwc_otg: Fix for occasional lockup on boot when doing a USB reset
dwc_otg: Don't issue traffic to LS devices in FS mode
Issuing low-speed packets when the root port is in full-speed mode
causes the root port to stop responding. Explicitly fail when
enqueuing URBs to a LS endpoint on a FS bus.
Fix ARM architecture issue with local_irq_restore()
If local_fiq_enable() is called before a local_irq_restore(flags) where
the flags variable has the F bit set, the FIQ will be erroneously disabled.
Fixup arch_local_irq_restore to avoid trampling the F bit in CPSR.
Also fix some of the hacks previously implemented for previous dwc_otg
incarnations.
dwc_otg: fiq_fsm: Base commit for driver rewrite
This commit removes the previous FIQ fixes entirely and adds fiq_fsm.
This rewrite features much more complete support for split transactions
and takes into account several OTG hardware bugs. High-speed
isochronous transactions are also capable of being performed by fiq_fsm.
All driver options have been removed and replaced with:
- dwc_otg.fiq_enable (bool)
- dwc_otg.fiq_fsm_enable (bool)
- dwc_otg.fiq_fsm_mask (bitmask)
- dwc_otg.nak_holdoff (unsigned int)
Defaults are specified such that fiq_fsm behaves similarly to the
previously implemented FIQ fixes.
fiq_fsm: Push error recovery into the FIQ when fiq_fsm is used
If the transfer associated with a QTD failed due to a bus error, the HCD
would retry the transfer up to 3 times (implementing the USB2.0
three-strikes retry in software).
Due to the masking mechanism used by fiq_fsm, it is only possible to pass
a single interrupt through to the HCD per-transfer.
In this instance host channels would fall off the radar because the error
reset would function, but the subsequent channel halt would be lost.
Push the error count reset into the FIQ handler.
fiq_fsm: Implement timeout mechanism
For full-speed endpoints with a large packet size, interrupt latency
runs the risk of the FIQ starting a transaction too late in a full-speed
frame. If the device is still transmitting data when EOF2 for the
downstream frame occurs, the hub will disable the port. This change is
not reflected in the hub status endpoint and the device becomes
unresponsive.
Prevent high-bandwidth transactions from being started too late in a
frame. The mechanism is not guaranteed: a combination of bit stuffing
and hub latency may still result in a device overrunning.
fiq_fsm: fix bounce buffer utilisation for Isochronous OUT
Multi-packet isochronous OUT transactions were subject to a few bounday
bugs. Fix them.
Audio playback is now much more robust: however, an issue stands with
devices that have adaptive sinks - ALSA plays samples too fast.
dwc_otg: Return full-speed frame numbers in HS mode
The frame counter increments on every *microframe* in high-speed mode.
Most device drivers expect this number to be in full-speed frames - this
caused considerable confusion to e.g. snd_usb_audio which uses the
frame counter to estimate the number of samples played.
fiq_fsm: save PID on completion of interrupt OUT transfers
Also add edge case handling for interrupt transports.
Note that for periodic split IN, data toggles are unimplemented in the
OTG host hardware - it unconditionally accepts any PID.
fiq_fsm: add missing case for fiq_fsm_tt_in_use()
Certain combinations of bitrate and endpoint activity could
result in a periodic transaction erroneously getting started
while the previous Isochronous OUT was still active.
fiq_fsm: clear hcintmsk for aborted transactions
Prevents the FIQ from erroneously handling interrupts
on a timed out channel.
fiq_fsm: enable by default
fiq_fsm: fix dequeues for non-periodic split transactions
If a dequeue happened between the SSPLIT and CSPLIT phases of the
transaction, the HCD would never receive an interrupt.
fiq_fsm: Disable by default
fiq_fsm: Handle HC babble errors
The HCTSIZ transfer size field raises a babble interrupt if
the counter wraps. Handle the resulting interrupt in this case.
dwc_otg: fix interrupt registration for fiq_enable=0
Additionally make the module parameter conditional for wherever
hcd->fiq_state is touched.
fiq_fsm: Enable by default
dwc_otg: Fix various issues with root port and transaction errors
Process the host port interrupts correctly (and don't trample them).
Root port hotplug now functional again.
Fix a few thinkos with the transaction error passthrough for fiq_fsm.
fiq_fsm: Implement hack for Split Interrupt transactions
Hubs aren't too picky about which endpoint we send Control type split
transactions to. By treating Interrupt transfers as Control, it is
possible to use the non-periodic queue in the OTG core as well as the
non-periodic FIFOs in the hub itself. This massively reduces the
microframe exclusivity/contention that periodic split transactions
otherwise have to enforce.
It goes without saying that this is a fairly egregious USB specification
violation, but it works.
Original idea by Hans Petter Selasky @ FreeBSD.org.
dwc_otg: FIQ support on SMP. Set up FIQ stack and handler on Core 0 only.
dwc_otg: introduce fiq_fsm_spin(un|)lock()
SMP safety for the FIQ relies on register read-modify write cycles being
completed in the correct order. Several places in the DWC code modify
registers also touched by the FIQ. Protect these by a bare-bones lock
mechanism.
This also makes it possible to run the FIQ and IRQ handlers on different
cores.
fiq_fsm: fix build on bcm2708 and bcm2709 platforms
dwc_otg: put some barriers back where they should be for UP
bcm2709/dwc_otg: Setup FIQ on core 1 if >1 core active
dwc_otg: fixup read-modify-write in critical paths
Be more careful about read-modify-write on registers that the FIQ
also touches.
Guard fiq_fsm_spin_lock with fiq_enable check
fiq_fsm: Falling out of the state machine isn't fatal
This edge case can be hit if the port is disabled while the FIQ is
in the middle of a transaction. Make the effects less severe.
Also get rid of the useless return value.
squash: dwc_otg: Allow to build without SMP
usb: core: make overcurrent messages more prominent
Hub overcurrent messages are more serious than "debug". Increase loglevel.
usb: dwc_otg: Don't use dma_to_virt()
Commit 6ce0d20 changes dma_to_virt() which breaks this driver.
Open code the old dma_to_virt() implementation to work around this.
Limit the use of __bus_to_virt() to cases where transfer_buffer_length
is set and transfer_buffer is not set. This is done to increase the
chance that this driver will also work on ARCH_BCM2835.
transfer_buffer should not be NULL if the length is set, but the
comment in the code indicates that there are situations where this
might happen. drivers/usb/isp1760/isp1760-hcd.c also has a similar
comment pointing to a possible: 'usb storage / SCSI bug'.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dwc_otg: Fix crash when fiq_enable=0
dwc_otg: fiq_fsm: Make high-speed isochronous strided transfers work properly
Certain low-bandwidth high-speed USB devices (specialist audio devices,
compressed-frame webcams) have packet intervals > 1 microframe.
Stride these transfers in the FIQ by using the start-of-frame interrupt
to restart the channel at the right time.
dwc_otg: Force host mode to fix incorrect compute module boards
dwc_otg: Add ARCH_BCM2835 support
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dwc_otg: Simplify FIQ irq number code
Dropping ATAGS means we can simplify the FIQ irq number code.
Also add error checking on the returned irq number.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dwc_otg: Remove duplicate gadget probe/unregister function
dwc_otg: Properly set the HFIR
Douglas Anderson reported:
According to the most up to date version of the dwc2 databook, the FRINT
field of the HFIR register should be programmed to:
* 125 us * (PHY clock freq for HS) - 1
* 1000 us * (PHY clock freq for FS/LS) - 1
This is opposed to older versions of the doc that claimed it should be:
* 125 us * (PHY clock freq for HS)
* 1000 us * (PHY clock freq for FS/LS)
and reported lower timing jitter on a USB analyser
dcw_otg: trim xfer length when buffer larger than allocated size is received
dwc_otg: Don't free qh align buffers in atomic context
dwc_otg: Enable the hack for Split Interrupt transactions by default
dwc_otg.fiq_fsm_mask=0xF has long been a suggestion for users with audio stutters or other USB bandwidth issues.
So far we are aware of many success stories but no failure caused by this setting.
Make it a default to learn more.
Martin Sperl [Fri, 2 Sep 2016 15:45:27 +0000 (16:45 +0100)]
Register the clocks early during the boot process,
so that special/critical clocks can get enabled early on
in the boot process avoiding the risk of disabling a clock,
pll_divider or pll when a claiming driver fails to install
propperly - maybe it needs to defer.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Noralf Trønnes [Fri, 7 Oct 2016 14:50:59 +0000 (16:50 +0200)]
watchdog: bcm2835: Support setting reboot partition
The Raspberry Pi firmware looks at the RSTS register to know which
partition to boot from. The reboot syscall command
LINUX_REBOOT_CMD_RESTART2 supports passing in a string argument.
Add support for passing in a partition number 0..63 to boot from.
Partition 63 is a special partiton indicating halt.
If the partition doesn't exist, the firmware falls back to partition 0.
Noralf Trønnes [Sat, 3 Oct 2015 20:22:55 +0000 (22:22 +0200)]
dmaengine: bcm2835: Load driver early and support legacy API
Load driver early since at least bcm2708_fb doesn't support deferred
probing and even if it did, we don't want the video driver deferred.
Support the legacy DMA API which is needed by bcm2708_fb.
Don't mask out channel 2.
Noralf Trønnes [Wed, 3 Jun 2015 10:26:13 +0000 (12:26 +0200)]
ARM: bcm2835: Set Serial number and Revision
The VideoCore bootloader passes in Serial number and
Revision number through Device Tree. Make these available to
userspace through /proc/cpuinfo.
Mainline status:
There is a commit in linux-next that standardize passing the serial
number through Device Tree (string: /serial-number):
ARM: 8355/1: arch: Show the serial number from devicetree in cpuinfo
There was an attempt to do the same with the revision number, but it
didn't get in:
[PATCH v2 1/2] arm: devtree: Set system_rev from DT revision
Phil Elwell [Wed, 24 Jun 2015 13:10:44 +0000 (14:10 +0100)]
spi-bcm2835: Support pin groups other than 7-11
The spi-bcm2835 driver automatically uses GPIO chip-selects due to
some unreliability of the native ones. In doing so it chooses the
same pins as the native chip-selects would use, but the existing
code always uses pins 7 and 8, wherever the SPI function is mapped.
Search the pinctrl group assigned to the driver for pins that
correspond to native chip-selects, and use those for GPIO chip-
selects.
Phil Elwell [Thu, 26 Feb 2015 09:58:22 +0000 (09:58 +0000)]
pinctrl-bcm2835: Only request the interrupts listed in the DTB
Although the GPIO controller can generate three interrupts (four counting
the common one), the device tree files currently only specify two. In the
absence of the third, simply don't register that interrupt (as opposed to
registering 0), which has the effect of making it impossible to generate
interrupts for GPIOs 46-53 which, since they share pins with the SD card
interface, is unlikely to be a problem.
Noralf Trønnes [Fri, 12 Jun 2015 17:01:05 +0000 (19:01 +0200)]
irqchip: bcm2835: Add FIQ support
Add a duplicate irq range with an offset on the hwirq's so the
driver can detect that enable_fiq() is used.
Tested with downstream dwc_otg USB controller driver.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org> Reviewed-by: Eric Anholt <eric@anholt.net> Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Phil Elwell [Fri, 4 Dec 2015 17:41:50 +0000 (17:41 +0000)]
irq-bcm2836: Prevent spurious interrupts, and trap them early
The old arch-specific IRQ macros included a dsb to ensure the
write to clear the mailbox interrupt completed before returning
from the interrupt. The BCM2836 irqchip driver needs the same
precaution to avoid spurious interrupts.
Spurious interrupts are still possible for other reasons,
though, so trap them early.
Eric Anholt [Fri, 19 Dec 2014 00:07:15 +0000 (16:07 -0800)]
mm: Remove the PFN busy warning
See commit dae803e165a11bc88ca8dbc07a11077caf97bbcb -- the warning is
expected sometimes when using CMA. However, that commit still spams
my kernel log with these warnings.
BugLink: http://bugs.launchpad.net/bugs/1709964
Commit 8d911904f3ce4 ('powerpc/perf: Add restrictions to PMC5 in power9 DD1')
was added to restrict the use of PMC5 in Power9 DD1. Intention was to disable
the use of PMC5 using raw event code. But instead of updating the
power9_isa207_pmu structure (used on DD1), the commit incorrectly updated the
power9_pmu structure. Fix it.
Fixes: 8d911904f3ce ("powerpc/perf: Add restrictions to PMC5 in power9 DD1") Reported-by: Shriya <shriyak@linux.vnet.ibm.com> Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com> Tested-by: Shriya <shriyak@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
(cherry picked from commit 8c218578fcbbbdb10416c8614658bf32e3bf1655) Signed-off-by: Joseph Salisbury <joseph.salisbury@canonical.com> Acked-by: Colin King <colin.king@canonical.com> Acked-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Support PTP Stick and Touchpad device. This Touchpad is Precision Touchpad
(PTP), and Stick Pointer data is the same as Mouse; Stick Pointer works as
Mouse.
[jkosina@suse.cz: changelog deuglification] Signed-off-by: Masaki Ota <masaki.ota@jp.alps.com> Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
(cherry picked from commit 504c932c7c47a6b4c572302a13873f7d83af1ff3) Signed-off-by: Shrirang Bagul <shrirang.bagul@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Seth Forshee <seth.forshee@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
UBUNTU: SAUCE: igb: add support for using Broadcom 54616 as PHY
BugLink: https://launchpad.net/bugs/1712024
Ported from packages/base/any/kernels/3.18.25/patches/driver-support-intel-igb-bcm54616-phy.patch
in OpenNetworkLinux https://github.com/opencomputeproject/OpenNetworkLinux/
Signed-off-by: Wen-chien Jesse Sung <jesse.sung@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-By: AceLan Kao <acelan.kao@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
- flush_tlb_mm() will flush the PWC which is unnecessary (for example
when doing a fork)
- A large unmap will call flush_tlb_pwc() multiple times causing us
to perform that fairly expensive operation repeatedly. This happens
often in batches of 3 on every new process.
So we change flush_tlb_mm() to only flush the TLB, and we use the
existing "need_flush_all" flag in struct mmu_gather to indicate
that the PWC needs flushing.
Unfortunately, flush_tlb_range() still needs to do a full flush
for now as it's used by the THP collapsing. We will fix that later.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
(backported from commit a46cc7a90fd8d95bfbb2b27080efe872a1a51db4 linux-next) Signed-off-by: Joseph Salisbury <joseph.salisbury@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Seth Forshee <seth.forshee@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
BugLink: http://bugs.launchpad.net/bugs/1709220
_tlbiel_pid() is called with a ric (Radix Invalidation Control) argument of
either RIC_FLUSH_TLB or RIC_FLUSH_ALL.
RIC_FLUSH_ALL says to invalidate the entire TLB and the Page Walk Cache (PWC).
To flush the whole TLB, we have to iterate over each set (congruence class) of
the TLB. Currently we do that and pass RIC_FLUSH_ALL each time. That is not
incorrect but it means we flush the PWC 128 times, when once would suffice.
Fix it by doing the first flush with the ric value we're passed, and then if it
was RIC_FLUSH_ALL, we downgrade it to RIC_FLUSH_TLB, because we know we have
just flushed the PWC and don't need to do it again.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
[mpe: Split out of combined patch, tweak logic, rewrite change log] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
(cherry picked from commit a5998fcb92552a18713b6aa5c146aa400e4d75ee) Signed-off-by: Joseph Salisbury <joseph.salisbury@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Seth Forshee <seth.forshee@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Shyam Sundar S K [Wed, 16 Aug 2017 12:03:00 +0000 (14:03 +0200)]
usb: xhci: Issue stop EP command only when the EP state is running
BugLink: https://bugs.launchpad.net/bugs/1711098
on AMD platforms with SNPS 3.1 USB controller if stop endpoint command is
issued the controller does not respond, when the EP is not in running
state. HW completes the command execution and reports
"Context State Error" completion code. This is as per the spec. However
HW on receiving the second command additionally marks EP to Flow control
state in HW which is RTL bug. This bug causes the HW not to respond
to any further doorbells that are rung by the driver. This makes the EP
to not functional anymore and causes gross functional failures.
As a workaround, not to hit this problem, it's better to check the EP state
and issue a stop EP command only when the EP is in running state.
As a sidenote, even with this patch there is still a possibility of
triggering the RTL bug if the context state races with the stop endpoint
command as described in xHCI spec 4.6.9
[code simplification and reworded sidenote in commit message -Mathias] Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com> Signed-off-by: Nehal Shah <Nehal-bakulchandra.Shah@amd.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 28a2369f7d72ece55089f33e7d7b9c1223673cc3) Signed-off-by: Alberto Milone <alberto.milone@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
In the current implementation, dma_fence_default_wait will always call
schedule_timeout() at least once for an unsignaled fence. This adds a
significant overhead to a fence status query.
Avoid this overhead by returning early if a zero timeout is specified.
v2: move early return after enable_signaling
Signed-off-by: Andres Rodriguez <andresx7@gmail.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.com> Link: http://patchwork.freedesktop.org/patch/msgid/20170426144620.3560-1-andresx7@gmail.com
(cherry picked from commit 03c0c5f6641533f5fc14bf4e76d2304197402552) Signed-off-by: Alberto Milone <alberto.milone@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
scsi: ipr: do not set DID_PASSTHROUGH on CHECK CONDITION
BugLink: http://bugs.launchpad.net/bugs/1682644
On a dual controller setup with multipath enabled, some MEDIUM ERRORs
caused both paths to be failed, thus I/O got queued/blocked since the
'queue_if_no_path' feature is enabled by default on IPR controllers.
This example disabled 'queue_if_no_path' so the I/O failure is seen at
the sg_dd program. Notice that after the sg_dd test-case, both paths
are in 'failed' state, and both path/priority groups are in 'enabled'
state (not 'active') -- which would block I/O with 'queue_if_no_path'.
This is not the desired behavior. The dm-multipath explicitly checks
for the MEDIUM ERROR case (and a few others) so not to fail the path
(e.g., I/O to other sectors could potentially happen without problems).
See dm-mpath.c :: do_end_io_bio() -> noretry_error() !->! fail_path().
The problem trace is:
1) ipr_scsi_done() // SENSE KEY/CHECK CONDITION detected, go to..
2) ipr_erp_start() // ipr_is_gscsi() and masked_ioasc OK, go to..
3) ipr_gen_sense() // masked_ioasc is IPR_IOASC_MED_DO_NOT_REALLOC,
// so set DID_PASSTHROUGH.
4) scsi_decide_disposition() // check for DID_PASSTHROUGH and return
// early on, faking a DID_OK.. *instead*
// of reaching scsi_check_sense().
// Had it reached the latter, that would
// set host_byte to DID_MEDIUM_ERROR.
5) scsi_finish_command()
6) scsi_io_completion()
7) __scsi_error_from_host_byte() // That would be converted to -ENODATA
<...>
8) dm_softirq_done()
9) multipath_end_io()
10) do_end_io()
11) noretry_error() // And that is checked in dm-mpath :: noretry_error()
// which would cause fail_path() not to be called.
With this patch applied, the I/O is failed but the paths are not. This
multipath device continues accepting more I/O requests without blocking.
(and notice the different host byte/driver byte handling per SCSI layer).
# dmesg
[...] sd 2:2:7:0: [sdaf] Done: SUCCESS Result: hostbyte=0x13 driverbyte=DRIVER_OK
[...] sd 2:2:7:0: [sdaf] CDB: Read(10) 28 00 00 00 00 00 00 00 40 00
[...] sd 2:2:7:0: [sdaf] Sense Key : Medium Error [current]
[...] sd 2:2:7:0: [sdaf] Add. Sense: Unrecovered read error - recommend rewrite the data
[...] blk_update_request: critical medium error, dev sdaf, sector 0
[...] blk_update_request: critical medium error, dev dm-6, sector 0
[...] sd 2:2:7:0: [sdaf] Done: SUCCESS Result: hostbyte=0x13 driverbyte=DRIVER_OK
[...] sd 2:2:7:0: [sdaf] CDB: Read(10) 28 00 00 00 00 00 00 00 10 00
[...] sd 2:2:7:0: [sdaf] Sense Key : Medium Error [current]
[...] sd 2:2:7:0: [sdaf] Add. Sense: Unrecovered read error - recommend rewrite the data
[...] blk_update_request: critical medium error, dev sdaf, sector 0
[...] blk_update_request: critical medium error, dev dm-6, sector 0
[...] Buffer I/O error on dev dm-6, logical block 0, async page read
Signed-off-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com> Acked-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit 785a470496d8e0a32e3d39f376984eb2c98ca5b3) Signed-off-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Colin King <colin.king@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Seth Forshee [Fri, 18 Aug 2017 15:08:00 +0000 (17:08 +0200)]
UBUNTU: [Config] CONFIG_MEMORY_HOTPLUG_DEFAULT_ONLINE=n for ppc64el
BugLink: http://bugs.launchpad.net/bugs/1709171 Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
(cherry picked from artful commit 8f189e08c9a0719aa1e615fcb5380ecb9bf12e7f) Signed-off-by: Joseph Salisbury <joseph.salisbury@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Colin King <colin.king@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Po-Hsu Lin [Thu, 10 Aug 2017 06:32:00 +0000 (08:32 +0200)]
selftests: fix memory-hotplug test
BugLink: http://bugs.launchpad.net/bugs/1710868
In the memory offline test, the $ration was used with RANDOM as the
possibility to get it offlined, correct it to become the portion of
available removable memory blocks.
Also ask the tool to try to offline the next available memory block
if the attempt is unsuccessful. It will only fail if all removable
memory blocks are busy.
A nice example:
$ sudo ./test.sh
Test scope: 10% hotplug memory
online all hot-pluggable memory in offline state:
SKIPPED - no hot-pluggable memory in offline state
offline 10% hot-pluggable memory in online state
trying to offline 3 out of 28 memory block(s):
online->offline memory1
online->offline memory10
./test.sh: line 74: echo: write error: Resource temporarily unavailable
offline_memory_expect_success 10: unexpected fail
online->offline memory100
online->offline memory101
online all hot-pluggable memory in offline state:
offline->online memory1
offline->online memory100
offline->online memory101
skip extra tests: debugfs is not mounted
$ echo $?
0
Signed-off-by: Po-Hsu Lin <po-hsu.lin@canonical.com> Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
(cherry picked from commit 5ff0c60b0e5e8c2a2139c304d7620b0ea70d721a) Signed-off-by: Po-Hsu Lin <po-hsu.lin@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Po-Hsu Lin [Thu, 10 Aug 2017 06:32:00 +0000 (08:32 +0200)]
selftests: add missing test name in memory-hotplug test
BugLink: http://bugs.launchpad.net/bugs/1710868
There is no prompt for testing memory notifier error injection,
added with the same echo format of other tests above.
Signed-off-by: Po-Hsu Lin <po-hsu.lin@canonical.com> Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
(cherry picked from commit 02d8f075ac44f6f0dc46881965f815576921f2c0) Signed-off-by: Po-Hsu Lin <po-hsu.lin@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
BugLink: http://bugs.launchpad.net/bugs/1686019
POWER9 running a radix guest will take some hypervisor interrupts
without going to real mode (turning off the MMU). This means that
early hypercall handlers may now be called in virtual mode. Most of
the handlers work just fine in both modes, but there are some that
can crash the host if called in virtual mode, notably the TCE (IOMMU)
hypercalls H_PUT_TCE, H_STUFF_TCE and H_PUT_TCE_INDIRECT. These
already have both a real-mode and a virtual-mode version, so we
arrange for the real-mode version to return H_TOO_HARD for radix
guests, which will result in the virtual-mode version being called.
The other hypercall which is sensitive to the MMU mode is H_RANDOM.
It doesn't have a virtual-mode version, so this adds code to enable
it to be called in either mode.
An alternative solution was considered which would refuse to call any
of the early hypercall handlers when doing a virtual-mode exit from a
radix guest. However, the XICS-on-XIVE code depends on the XICS
hypercalls being handled early even for virtual-mode exits, because
the handlers need to be called before the XIVE vCPU state has been
pulled off the hardware. Therefore that solution would have become
quite invasive and complicated, and was rejected in favour of the
simpler, though less elegant, solution presented here.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au> Tested-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
(cherry picked from commit acde25726bc6034b628febb8a4c6c0838736ccbf) Signed-off-by: Jose Ricardo Ziviani <joserz@linux.vnet.ibm.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The capability will tell the user space whether in-kernel handlers of
H_PUT_TCE can handle VFIO-targeted requests or not. If not, the user space
must not attempt allocating a TCE table in the host kernel via
the KVM_CREATE_SPAPR_TCE KVM ioctl because in that case TCE requests
will not be passed to the user space which is desired action in
the situation like that.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru> Reviewed-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
(backported from commit 4898d3f49b5b156c33f0ae0f49ede417ab86195e)
[joserz: small change on file include/uapi/linux/kvm.h due to conflics
with defines included by MIPS and S390 patches.] Signed-off-by: Jose Ricardo Ziviani <joserz@linux.vnet.ibm.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
powerpc/mmu: Add real mode support for IOMMU preregistered memory
BugLink: http://bugs.launchpad.net/bugs/1686019
This makes mm_iommu_lookup() able to work in realmode by replacing
list_for_each_entry_rcu() (which can do debug stuff which can fail in
real mode) with list_for_each_entry_lockless().
This adds realmode version of mm_iommu_ua_to_hpa() which adds
explicit vmalloc'd-to-linear address conversion.
Unlike mm_iommu_ua_to_hpa(), mm_iommu_ua_to_hpa_rm() can fail.
This changes mm_iommu_preregistered() to receive @mm as in real mode
@current does not always have a correct pointer.
This adds realmode version of mm_iommu_lookup() which receives @mm
(for the same reason as for mm_iommu_preregistered()) and uses
lockless version of list_for_each_entry_rcu().
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru> Reviewed-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
(cherry picked from commit 6b5c19c55266f6efd10ffac0e9f9f2b7aa420a58) Signed-off-by: Jose Ricardo Ziviani <joserz@linux.vnet.ibm.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
powerpc/vfio_spapr_tce: Add reference counting to iommu_table
BugLink: http://bugs.launchpad.net/bugs/1686019
So far iommu_table obejcts were only used in virtual mode and had
a single owner. We are going to change this by implementing in-kernel
acceleration of DMA mapping requests. The proposed acceleration
will handle requests in real mode and KVM will keep references to tables.
This adds a kref to iommu_table and defines new helpers to update it.
This replaces iommu_free_table() with iommu_tce_table_put() and makes
iommu_free_table() static. iommu_tce_table_get() is not used in this patch
but it will be in the following patch.
Since this touches prototypes, this also removes @node_name parameter as
it has never been really useful on powernv and carrying it for
the pseries platform code to iommu_free_table() seems to be quite
useless as well.
This should cause no behavioral change.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru> Reviewed-by: David Gibson <david@gibson.dropbear.id.au> Acked-by: Alex Williamson <alex.williamson@redhat.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
(cherry picked from commit e5afdf9dd515a9446c009f44f99f9bc2f91b89a7) Signed-off-by: Jose Ricardo Ziviani <joserz@linux.vnet.ibm.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
BugLink: http://bugs.launchpad.net/bugs/1686019
At the moment iommu_table can be disposed by either calling
iommu_table_free() directly or it_ops::free(); the only implementation
of free() is in IODA2 - pnv_ioda2_table_free() - and it calls
iommu_table_free() anyway.
As we are going to have reference counting on tables, we need an unified
way of disposing tables.
This moves it_ops::free() call into iommu_free_table() and makes use
of the latter. The free() callback now handles only platform-specific
data.
As from now on the iommu_free_table() calls it_ops->free(), we need
to have it_ops initialized before calling iommu_free_table() so this
moves this initialization in pnv_pci_ioda2_create_table().
This should cause no behavioral change.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru> Reviewed-by: David Gibson <david@gibson.dropbear.id.au> Acked-by: Alex Williamson <alex.williamson@redhat.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
(cherry picked from commit 11edf116e3a6352cfee6b1437d41603c9aff79c9) Signed-off-by: Jose Ricardo Ziviani <joserz@linux.vnet.ibm.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
powerpc/powernv/ioda2: Update iommu table base on ownership change
BugLink: http://bugs.launchpad.net/bugs/1686019
On POWERNV platform, in order to do DMA via IOMMU (i.e. 32bit DMA in
our case), a device needs an iommu_table pointer set via
set_iommu_table_base().
The codeflow is:
- pnv_pci_ioda2_setup_dma_pe()
- pnv_pci_ioda2_setup_default_config()
- pnv_ioda_setup_bus_dma() [1]
pnv_pci_ioda2_setup_dma_pe() creates IOMMU groups,
pnv_pci_ioda2_setup_default_config() does default DMA setup,
pnv_ioda_setup_bus_dma() takes a bus PE (on IODA2, all physical function
PEs as bus PEs except NPU), walks through all underlying buses and
devices, adds all devices to an IOMMU group and sets iommu_table.
On IODA2, when VFIO is used, it takes ownership over a PE which means it
removes all tables and creates new ones (with a possibility of sharing
them among PEs). So when the ownership is returned from VFIO to
the kernel, the iommu_table pointer written to a device at [1] is
stale and needs an update.
This adds an "add_to_group" parameter to pnv_ioda_setup_bus_dma()
(in fact re-adds as it used to be there a while ago for different
reasons) to tell the helper if a device needs to be added to
an IOMMU group with an iommu_table update or just the latter.
This calls pnv_ioda_setup_bus_dma(..., false) from
pnv_ioda2_release_ownership() so when the ownership is restored,
32bit DMA can work again for a device. This does the same thing
on obtaining ownership as the iommu_table point is stale at this point
anyway and it is safer to have NULL there.
We did not hit this earlier as all tested devices in recent years were
only using 64bit DMA; the rare exception for this is MPT3 SAS adapter
which uses both 32bit and 64bit DMA access and it has not been tested
with VFIO much.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru> Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com> Reviewed-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
(cherry picked from commit db08e1d53034a54fe177ced70476fda73954b9e9) Signed-off-by: Jose Ricardo Ziviani <joserz@linux.vnet.ibm.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
powerpc/powernv/iommu: Add real mode version of iommu_table_ops::exchange()
BugLink: http://bugs.launchpad.net/bugs/1686019
In real mode, TCE tables are invalidated using special
cache-inhibited store instructions which are not available in
virtual mode
This defines and implements exchange_rm() callback. This does not
define set_rm/clear_rm/flush_rm callbacks as there is no user for those -
exchange/exchange_rm are only to be used by KVM for VFIO.
The exchange_rm callback is defined for IODA1/IODA2 powernv platforms.
This replaces list_for_each_entry_rcu with its lockless version as
from now on pnv_pci_ioda2_tce_invalidate() can be called in
the real mode too.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru> Reviewed-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
(cherry picked from commit a540aa56ba3d29084f28710c8b93cc9c3c422943) Signed-off-by: Jose Ricardo Ziviani <joserz@linux.vnet.ibm.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
KVM: PPC: VFIO: Add in-kernel acceleration for VFIO
BugLink: http://bugs.launchpad.net/bugs/1686019
This allows the host kernel to handle H_PUT_TCE, H_PUT_TCE_INDIRECT
and H_STUFF_TCE requests targeted an IOMMU TCE table used for VFIO
without passing them to user space which saves time on switching
to user space and back.
This adds H_PUT_TCE/H_PUT_TCE_INDIRECT/H_STUFF_TCE handlers to KVM.
KVM tries to handle a TCE request in the real mode, if failed
it passes the request to the virtual mode to complete the operation.
If it a virtual mode handler fails, the request is passed to
the user space; this is not expected to happen though.
To avoid dealing with page use counters (which is tricky in real mode),
this only accelerates SPAPR TCE IOMMU v2 clients which are required
to pre-register the userspace memory. The very first TCE request will
be handled in the VFIO SPAPR TCE driver anyway as the userspace view
of the TCE table (iommu_table::it_userspace) is not allocated till
the very first mapping happens and we cannot call vmalloc in real mode.
If we fail to update a hardware IOMMU table unexpected reason, we just
clear it and move on as there is nothing really we can do about it -
for example, if we hot plug a VFIO device to a guest, existing TCE tables
will be mirrored automatically to the hardware and there is no interface
to report to the guest about possible failures.
This adds new attribute - KVM_DEV_VFIO_GROUP_SET_SPAPR_TCE - to
the VFIO KVM device. It takes a VFIO group fd and SPAPR TCE table fd
and associates a physical IOMMU table with the SPAPR TCE table (which
is a guest view of the hardware IOMMU table). The iommu_table object
is cached and referenced so we do not have to look up for it in real mode.
This does not implement the UNSET counterpart as there is no use for it -
once the acceleration is enabled, the existing userspace won't
disable it unless a VFIO container is destroyed; this adds necessary
cleanup to the KVM_DEV_VFIO_GROUP_DEL handler.
This advertises the new KVM_CAP_SPAPR_TCE_VFIO capability to the user
space.
This adds real mode version of WARN_ON_ONCE() as the generic version
causes problems with rcu_sched. Since we testing what vmalloc_to_phys()
returns in the code, this also adds a check for already existing
vmalloc_to_phys() call in kvmppc_rm_h_put_tce_indirect().
This finally makes use of vfio_external_user_iommu_id() which was
introduced quite some time ago and was considered for removal.
Tests show that this patch increases transmission speed from 220MB/s
to 750..1020MB/s on 10Gb network (Chelsea CXGB3 10Gb ethernet card).
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru> Acked-by: Alex Williamson <alex.williamson@redhat.com> Reviewed-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
(backported from commit 121f80ba68f1a5779a36d7b3247206e60e0a7418)
[joserz: removed WARN_ON(!kref_read(&stit->kref)); to avoid a dependency
to commit 2c935bc, that adds sensible changes to other important kernel
components.] Signed-off-by: Jose Ricardo Ziviani <joserz@linux.vnet.ibm.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
KVM: PPC: Use preregistered memory API to access TCE list
BugLink: http://bugs.launchpad.net/bugs/1686019
VFIO on sPAPR already implements guest memory pre-registration
when the entire guest RAM gets pinned. This can be used to translate
the physical address of a guest page containing the TCE list
from H_PUT_TCE_INDIRECT.
This makes use of the pre-registrered memory API to access TCE list
pages in order to avoid unnecessary locking on the KVM memory
reverse map as we know that all of guest memory is pinned and
we have a flat array mapping GPA to HPA which makes it simpler and
quicker to index into that array (even with looking up the
kernel page tables in vmalloc_to_phys) than it is to find the memslot,
lock the rmap entry, look up the user page tables, and unlock the rmap
entry. Note that the rmap pointer is initialized to NULL
where declared (not in this patch).
If a requested chunk of memory has not been preregistered, this will
fall back to non-preregistered case and lock rmap.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru> Reviewed-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
(cherry picked from commit da6f59e19233efdda58f196afbae8e05f6030d7f) Signed-off-by: Jose Ricardo Ziviani <joserz@linux.vnet.ibm.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
BugLink: http://bugs.launchpad.net/bugs/1686019
The guest view TCE tables are per KVM anyway (not per VCPU) so pass kvm*
there. This will be used in the following patches where we will be
attaching VFIO containers to LIOBNs via ioctl() to KVM (rather than
to VCPU).
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru> Reviewed-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
(cherry picked from commit 503bfcbe18576a79be0bc5173b23b530845e704a) Signed-off-by: Jose Ricardo Ziviani <joserz@linux.vnet.ibm.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Timur Tabi [Tue, 8 Aug 2017 17:44:00 +0000 (19:44 +0200)]
tty: pl011: fix initialization order of QDF2400 E44
The work-around for Qualcomm Technologies QDF2400 Erratum 44 hinges on a
global variable defined in the pl011 driver. The ACPI SPCR parsing code
determines whether the work-around is needed, and if so, it changes the
console name from "pl011" to "qdf2400_e44". The expectation is that
the pl011 driver will implement the work-around when it sees the console
name. The global variable qdf2400_e44_present is set when that happens.
The problem is that work-around needs to be enabled when the pl011
driver probes, not when the console name is queried. However, sbsa_probe()
is called before pl011_console_match(). The work-around appeared to work
previously because the default console on QDF2400 platforms was always
ttyAMA1. The first time sbsa_probe() is called (for ttyAMA0),
qdf2400_e44_present is still false. Then pl011_console_match() is called,
and it sets qdf2400_e44_present to true. All subsequent calls to
sbsa_probe() enable the work-around.
The solution is to move the global variable into spcr.c and let the
pl011 driver query it during probe time. This works because all QDF2400
platforms require SPCR, so parse_spcr() will always be called.
pl011_console_match still checks for the "qdf2400_e44" console name,
but it doesn't do anything else special.
BugLink: https://launchpad.net/bugs/1709123 Fixes: 5a0722b898f8 ("tty: pl011: use "qdf2400_e44" as the earlycon name for QDF2400 E44") Tested-by: Jeffrey Hugo <jhugo@codeaurora.org> Signed-off-by: Timur Tabi <timur@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(backported from commit 37ef38f3f83891a2f413fb872bae7d0f9bb95b27) Signed-off-by: Manoj Iyer <manoj.iyer@canonical.com> Acked-by: Seth Forshee <seth.forshee@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
J. R. Okajima [Thu, 17 Aug 2017 13:09:00 +0000 (15:09 +0200)]
UBUNTU: SAUCE: aufs: bugfix, for v4.10, copy-up on XFS branch
BugLink: http://bugs.launchpad.net/bugs/1709749
The commit for linux-v4.10 6552321 2016-11-30 xfs: remove i_iolock and use i_rwsem in the
VFS inode instead
broke aufs' copy-up because XFS acquires inode_lock for a normal read().
Additionally XFS has its version and older one doesn't support
clone_file_range().
This commit fixes the error path after trying clone_file_range().
Reported-by: Vasily Tarasov <tarasov@vasily.name>
See-also: http://www.mail-archive.com/aufs-users@lists.sourceforge.net/msg05498.html Signed-off-by: J. R. Okajima <hooanon05g@gmail.com>
(cherry picked from commit e34c81ff96415c64ca827ec30e7935454d26c1d3
https://github.com/sfjro/aufs4-standalone.git) Signed-off-by: Seth Forshee <seth.forshee@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
J. R. Okajima [Thu, 17 Aug 2017 13:09:00 +0000 (15:09 +0200)]
UBUNTU: SAUCE: aufs: for v4.5, use vfs_clone_file_range() in copy-up
BugLink: http://bugs.launchpad.net/bugs/1709749
In mainline, ioctl(FICLONE) is introduced by the commit 04b38d6 2015-12-07 vfs: pull btrfs clone API to vfs layer
so are vfs_clone_file_ranage() and f_op->clone_file_ranage().
Compared to copy_file_range(2), cloning doesn't return with the partial
success. Using this method in aufs copy-up, the speed will be improved.
But unfortunately this method is supported by nfs4.2, btrfs and cifs
only (currently). Additionally, linux nfs server 4.2 implementation
simply calls vfs_clone_file_ranage(), which means if the backend fs
doesn't support this operation, it returns EOPNOTSUPP.
So the benefit is rather limited, but it must be a good thing.
Signed-off-by: J. R. Okajima <hooanon05g@gmail.com>
(backported from commit b4d3dcc92a13d53952fe6e9a640201ef87475302
https://github.com/sfjro/aufs4-standalone.git)
[saf: Resolved conflicts based primarily on resolution found in fd18affa818115edad7e1b7472f26ac4d73e73a1] Signed-off-by: Seth Forshee <seth.forshee@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Hanjun Guo [Wed, 16 Aug 2017 17:56:00 +0000 (19:56 +0200)]
ACPI: APD: Fix HID for Hisilicon Hip07/08
BugLink: https://bugs.launchpad.net/bugs/1711182
ACPI HID for Hisilicon Hip07/08 should be HISI02A1/2,
not HISI0A21/2, HISI02A1/2 was tested ok but was modified
by the stupid typo when upstream the patches (by me),
correct them to the right IDs (matching the IDs in
drivers/i2c/busses/i2c-designware-platdrv.c).
Fixes: 6e14cf361a0c (ACPI / APD: Add clock frequency for Hisilicon Hip07/08 I2C controller) Reported-by: Tao Tian <tiantao6@huawei.com> Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
(backported from commit f7f3dd5b4cbb138ed4559b0d096bab76a8f476de) Signed-off-by: dann frazier <dann.frazier@canonical.com> Acked-by: Seth Forshee <seth.forshee@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Ming Lei [Mon, 7 Aug 2017 12:43:00 +0000 (14:43 +0200)]
block: fix bio_will_gap() for first bvec with offset
BugLink: http://bugs.launchpad.net/bugs/1709073
Commit 729204ef49ec("block: relax check on sg gap") allows us to merge
bios, if both are physically contiguous. This change can merge a huge
number of small bios, through mkfs for example, mkfs.ntfs running time
can be decreased to ~1/10.
But if one rq starts with a non-aligned buffer (the 1st bvec's bv_offset
is non-zero) and if we allow the merge, it is quite difficult to respect
sg gap limit, especially the max segment size, or we risk having an
unaligned virtual boundary. This patch tries to avoid the issue by
disallowing a merge, if the req starts with an unaligned buffer.
Also add comments to explain why the merged segment can't end in
unaligned virt boundary.
Fixes: 729204ef49ec ("block: relax check on sg gap") Tested-by: Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Ming Lei <ming.lei@redhat.com>
Rewrote parts of the commit message and comments.
Arend van Spriel [Tue, 22 Aug 2017 09:08:00 +0000 (11:08 +0200)]
brcmfmac: fix possible buffer overflow in brcmf_cfg80211_mgmt_tx()
The lower level nl80211 code in cfg80211 ensures that "len" is between
25 and NL80211_ATTR_FRAME (2304). We subtract DOT11_MGMT_HDR_LEN (24) from
"len" so thats's max of 2280. However, the action_frame->data[] buffer is
only BRCMF_FIL_ACTION_FRAME_SIZE (1800) bytes long so this memcpy() can
overflow.
Cc: stable@vger.kernel.org # 3.9.x Fixes: 18e2f61db3b70 ("brcmfmac: P2P action frame tx.") Reported-by: "freenerguo(郭大兴)" <freenerguo@tencent.com> Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
CVE-2017-7541
(cherry-picked from commit 8f44c9a41386729fea410e688959ddaa9d51be7c) Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Acked-by: Colin King <colin.king@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
UBUNTU: [Packaging] sort ABI files with C.UTF-8 locale
BugLink: https://bugs.launchpad.net/bugs/1712345
Whenever we update the ABI files, the files may be sorted in a different
order, even though their contents are the same. That happens because the
system updating the ABI files may use a different locale than the one
that was used previously.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Acked-by: Marcelo Cerri <marcelo.cerri@canonical.com> Acked-by: Colin King <colin.king@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
BugLink: http://bugs.launchpad.net/bugs/1700972
Allow images to be created without the need of an initrd and also allow
users to run without an initrd if they want to.
Willem de Bruijn [Thu, 10 Aug 2017 16:29:19 +0000 (12:29 -0400)]
udp: consistently apply ufo or fragmentation
When iteratively building a UDP datagram with MSG_MORE and that
datagram exceeds MTU, consistently choose UFO or fragmentation.
Once skb_is_gso, always apply ufo. Conversely, once a datagram is
split across multiple skbs, do not consider ufo.
Sendpage already maintains the first invariant, only add the second.
IPv6 does not have a sendpage implementation to modify.
A gso skb must have a partial checksum, do not follow sk_no_check_tx
in udp_send_skb.
Found by syzkaller.
Fixes: e89e9cf539a2 ("[IPv4/IPv6]: UFO Scatter-gather approach") Reported-by: Andrey Konovalov <andreyknvl@google.com> Signed-off-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
CVE-2017-1000112
Willem de Bruijn [Thu, 10 Aug 2017 16:41:58 +0000 (12:41 -0400)]
packet: fix tp_reserve race in packet_set_ring
Updates to tp_reserve can race with reads of the field in
packet_set_ring. Avoid this by holding the socket lock during
updates in setsockopt PACKET_RESERVE.
This bug was discovered by syzkaller.
Fixes: 8913336a7e8d ("packet: add PACKET_RESERVE sockopt") Reported-by: Andrey Konovalov <andreyknvl@google.com> Signed-off-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
CVE-2017-1000111
Marc Zyngier [Fri, 9 Jun 2017 11:49:56 +0000 (12:49 +0100)]
KVM: arm64: Log an error if trapping a write-to-read-only GICv3 access
BugLink: https://bugs.launchpad.net/bugs/1673564
A write-to-read-only GICv3 access should UNDEF at EL1. But since
we're in complete paranoia-land with broken CPUs, let's assume the
worse and gracefully handle the case.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Reviewed-by: Christoffer Dall <cdall@linaro.org> Signed-off-by: Christoffer Dall <cdall@linaro.org>
(backported picked from commit 7b1dba1f7325629427c0e5bdf014159b229d16c8)
[ dannf: Recoded sys_reg_descs[] entries to use pre-SYS_DESC() syntax and
minor context changes. ] Signed-off-by: dann frazier <dann.frazier@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Marc Zyngier [Fri, 9 Jun 2017 11:49:55 +0000 (12:49 +0100)]
KVM: arm64: Log an error if trapping a read-from-write-only GICv3 access
BugLink: https://bugs.launchpad.net/bugs/1673564
A read-from-write-only GICv3 access should UNDEF at EL1. But since
we're in complete paranoia-land with broken CPUs, let's assume the
worse and gracefully handle the case.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Reviewed-by: Christoffer Dall <cdall@linaro.org> Signed-off-by: Christoffer Dall <cdall@linaro.org>
(backported from commit e7f1d1eef482150a64a6e6ad8faf40f8f97eed67)
[ dannf: Dropped hunk in access_pmswinc since WO check wasn't added
until e0443230. Recoded sys_reg_descs[] entries to use pre-SYS_DESC()
syntax. Other context changes. ] Signed-off-by: dann frazier <dann.frazier@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Marc Zyngier [Mon, 27 Mar 2017 16:03:40 +0000 (17:03 +0100)]
arm64: KVM: Make unexpected reads from WO registers inject an undef
BugLink: https://bugs.launchpad.net/bugs/1673564
Reads from write-only system registers are generally confined to
EL1 and not propagated to EL2 (that's what the architecture
mantates). In order to be sure that we have a sane behaviour
even in the unlikely event that we have a broken system, we still
handle it in KVM.
In that case, let's inject an undef into the guest.
Let's also remove write_to_read_only which isn't used anywhere.
Reviewed-by: Christoffer Dall <cdall@linaro.org> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
(cherry picked from commit 7b5b4df1a79954e0b208630fc63b16ec0231a516) Signed-off-by: dann frazier <dann.frazier@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Tested-by: Alexander Graf <agraf@suse.de> Acked-by: David Daney <david.daney@cavium.com> Acked-by: Christoffer Dall <cdall@linaro.org> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Christoffer Dall <cdall@linaro.org>
(cherry picked from commit 2873b5082c5fbe2037f12e8d2abc8ad8f8d82a1b) Signed-off-by: dann frazier <dann.frazier@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Marc Zyngier [Fri, 9 Jun 2017 11:49:53 +0000 (12:49 +0100)]
KVM: arm64: Enable GICv3 common sysreg trapping via command-line
BugLink: https://bugs.launchpad.net/bugs/1673564
Now that we're able to safely handle common sysreg access, let's
give the user the opportunity to enable it by passing a specific
command-line option (vgic_v3.common_trap).
Tested-by: Alexander Graf <agraf@suse.de> Acked-by: David Daney <david.daney@cavium.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Acked-by: Christoffer Dall <cdall@linaro.org> Signed-off-by: Christoffer Dall <cdall@linaro.org>
(cherry picked from commit ff89511ef29b794d6a9c6b62f5ea76fc013cdae7) Signed-off-by: dann frazier <dann.frazier@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Marc Zyngier [Fri, 9 Jun 2017 11:49:52 +0000 (12:49 +0100)]
KVM: arm64: vgic-v3: Add ICV_PMR_EL1 handler
BugLink: https://bugs.launchpad.net/bugs/1673564
Add a handler for reading/writing the guest's view of the ICC_PMR_EL1
register, which is located in the ICH_VMCR_EL2.VPMR field.
Tested-by: Alexander Graf <agraf@suse.de> Acked-by: David Daney <david.daney@cavium.com> Acked-by: Christoffer Dall <cdall@linaro.org> Reviewed-by: Eric Auger <eric.auger@redhat.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Christoffer Dall <cdall@linaro.org>
(backported from commit 6293d6514d6b0945210e15edcecc71d99cfca97c)
[ dannf: Dropped SYS_ prefix on ICC_PMR_EL1 macro, which wasn't
added upstream until 0e9884fe ] Signed-off-by: dann frazier <dann.frazier@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Marc Zyngier [Fri, 9 Jun 2017 11:49:51 +0000 (12:49 +0100)]
KVM: arm64: vgic-v3: Add ICV_CTLR_EL1 handler
BugLink: https://bugs.launchpad.net/bugs/1673564
Add a handler for reading/writing the guest's view of the ICV_CTLR_EL1
register. only EOIMode and CBPR are of interest here, as all the other
bits directly come from ICH_VTR_EL2 and are Read-Only.
Tested-by: Alexander Graf <agraf@suse.de> Acked-by: David Daney <david.daney@cavium.com> Acked-by: Christoffer Dall <cdall@linaro.org> Reviewed-by: Eric Auger <eric.auger@redhat.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Christoffer Dall <cdall@linaro.org>
(backported from commit d840b2d37d3ef2463db38274c6fd72619acbe216)
[ dannf: Dropped SYS_ prefix on ICC_DIR_EL1 macro, which wasn't
added upstream until 0e9884fe ] Signed-off-by: dann frazier <dann.frazier@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Marc Zyngier [Fri, 9 Jun 2017 11:49:50 +0000 (12:49 +0100)]
KVM: arm64: vgic-v3: Add ICV_RPR_EL1 handler
BugLink: https://bugs.launchpad.net/bugs/1673564
Add a handler for reading the guest's view of the ICV_RPR_EL1
register, returning the highest active priority.
Tested-by: Alexander Graf <agraf@suse.de> Acked-by: David Daney <david.daney@cavium.com> Acked-by: Christoffer Dall <cdall@linaro.org> Reviewed-by: Eric Auger <eric.auger@redhat.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Christoffer Dall <cdall@linaro.org>
(backported from commit 43515894c06f856b7743145e002591309f60b247)
[ dannf: Drop the SYS_ prefix and move the ICV_RPR_EL1 macro definition
from asm/sysreg.h to asm/arch_gicv3.h for consistency with code
prior to 0e9884fe ] Signed-off-by: dann frazier <dann.frazier@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Marc Zyngier [Fri, 9 Jun 2017 11:49:49 +0000 (12:49 +0100)]
KVM: arm64: vgic-v3: Add ICV_DIR_EL1 handler
BugLink: https://bugs.launchpad.net/bugs/1673564
Add a handler for writing the guest's view of the ICC_DIR_EL1
register, performing the deactivation of an interrupt if EOImode
is set ot 1.
Tested-by: Alexander Graf <agraf@suse.de> Acked-by: David Daney <david.daney@cavium.com> Reviewed-by: Christoffer Dall <cdall@linaro.org> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Christoffer Dall <cdall@linaro.org>
(backported from commit 40228ba57c8532d4977d684a363915402d85dbf9)
[ dannf: Dropped SYS_ prefix on ICV_DIR_EL1 macro, which wasn't
added upstream until 0e9884fe ] Signed-off-by: dann frazier <dann.frazier@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
David Daney [Fri, 9 Jun 2017 11:49:48 +0000 (12:49 +0100)]
arm64: Add workaround for Cavium Thunder erratum 30115
BugLink: https://bugs.launchpad.net/bugs/1673564
Some Cavium Thunder CPUs suffer a problem where a KVM guest may
inadvertently cause the host kernel to quit receiving interrupts.
Use the Group-0/1 trapping in order to deal with it.
[maz]: Adapted patch to the Group-0/1 trapping, reworked commit log
Tested-by: Alexander Graf <agraf@suse.de> Acked-by: Catalin Marinas <catalin.marinas@arm.com> Reviewed-by: Eric Auger <eric.auger@redhat.com> Signed-off-by: David Daney <david.daney@cavium.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Christoffer Dall <cdall@linaro.org>
(cherry picked from commit 690a341577f9adf2c275ababe0dcefe91898bbf0) Signed-off-by: dann frazier <dann.frazier@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>