Aron Szabo [Sat, 16 Jun 2012 10:15:55 +0000 (12:15 +0200)]
lirc: added support for RaspberryPi GPIO
lirc_rpi: Use read_current_timer to determine transmitter delay. Thanks to jjmz and others
See: https://github.com/raspberrypi/linux/issues/525
lirc: Remove restriction on gpio pins that can be used with lirc
Compute Module, for example could use different pins
lirc_rpi: Add parameter to specify input pin pull
Depending on the connected IR circuitry it might be desirable to change the
gpios internal pull from it pull-down default behaviour. Add a module
parameter to allow the user to set it explicitly.
Signed-off-by: Julian Scheel <julian@jusst.de>
lirc-rpi: Use the higher-level irq control functions
This module used to access the irq_chip methods of the
gpio controller directly, rather than going through the
standard enable_irq/irq_set_irq_type functions. This
caused problems on pinctrl-bcm2835 which only implements
the irq_enable/disable methods and not irq_unmask/mask.
lirc-rpi: Correct the interrupt usage
1) Correct the use of enable_irq (i.e. don't call it so often)
2) Correct the shutdown sequence.
3) Avoid a bcm2708_gpio driver quirk by setting the irq flags earlier
lirc-rpi: use getnstimeofday instead of read_current_timer
read_current_timer isn't guaranteed to return values in
microseconds, and indeed it doesn't on a Pi2.
Issue: linux#827
lirc-rpi: Add device tree support, and a suitable overlay
The overlay supports DT parameters that match the old module
parameters, except that gpio_in_pull should be set using the
strings "up", "down" or "off".
lirc-rpi: Also support pinctrl-bcm2835 in non-DT mode
fix auto-sense in lirc_rpi driver
On a Raspberry Pi 2, the lirc_rpi driver might receive spurious
interrupts and change it's low-active / high-active setting.
When this happens, the IR remote control stops working.
This patch disables this auto-detection if the 'sense' parameter
was set in the device tree, making the driver robust to such
spurious interrupts.
Tim Gover [Tue, 22 Jul 2014 14:41:04 +0000 (15:41 +0100)]
vcsm: VideoCore shared memory service for BCM2835
Add experimental support for the VideoCore shared memory service.
This allows user processes to allocate memory from VideoCore's
GPU relocatable heap and mmap the buffers. Additionally, the memory
handles can passed to other VideoCore services such as MMAL, OpenMax
and DispmanX
TODO
* This driver was originally released for BCM28155 which has a different
cache architecture to BCM2835. Consequently, in this release only
uncached mappings are supported. However, there's no fundamental
reason which cached mappings cannot be support or BCM2835
* More refactoring is required to remove the typedefs.
* Re-enable the some of the commented out debug-fs statistics which were
disabled when migrating code from proc-fs.
* There's a lot of code to support sharing of VCSM in order to support
Android. This could probably done more cleanly or perhaps just
removed.
Signed-off-by: Tim Gover <timgover@gmail.com>
config: Disable VC_SM for now to fix hang with cutdown kernel
vcsm: Use boolean as it cannot be built as module
On building the bcm_vc_sm as a module we get the following error:
v7_dma_flush_range and do_munmap are undefined in vc-sm.ko.
popcornmix [Mon, 26 Mar 2012 21:15:50 +0000 (22:15 +0100)]
bcm2708: alsa sound driver
Signed-off-by: popcornmix <popcornmix@gmail.com>
alsa: add mmap support and some cleanups to bcm2835 ALSA driver
snd-bcm2835: Add support for spdif/hdmi passthrough
This adds a dedicated subdevice which can be used for passthrough of non-audio
formats (ie encoded a52) through the hdmi audio link. In addition to this
driver extension an appropriate card config is required to make alsa-lib
support the AES parameters for this device.
snd-bcm2708: Add mutex, improve logging
Fix for ALSA driver crash
Avoids an issue when closing and opening vchiq where a message can arrive before service handle has been written
alsa: reduce severity of expected warning message
snd-bcm2708: Fix dmesg spam for non-error case
alsa: Ensure mutexes are released through error paths
alsa: Make interrupted close paths quieter
BCM270x: Add onboard sound device to Device Tree
Add Device Tree support to alsa driver.
Add device to Device Tree.
Don't add platform devices when booting in DT mode.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
bcm2835: access controls under the audio mutex
I don't think the ALSA framework provides any kind of automatic
synchronization within the control callbacks. We most likely need
to ensure this manually, so add locking around all access to shared
mutable data. In particular, bcm2835_audio_set_ctls() should
probably always be called under our own audio lock.
snd-bcm2835: Don't allow responses from VC to be interrupted by user signals
There should always be a response, and retry after a signal interruption is not handled, so don't report
we are interruptible.
Phil Elwell [Wed, 11 May 2016 11:50:33 +0000 (12:50 +0100)]
mmc: Add MMC_QUIRK_ERASE_BROKEN for some cards
Some SD cards have been found that corrupt data when small blocks
are erased. Add a quirk to indicate that ERASE should not be used,
and set it for cards of that type.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
mmc: Apply QUIRK_BROKEN_ERASE to other capacities
Use mmc_block.card_quirks to override the quirks for all SD or MMC
cards. The value is a bitfield using the bit positions defined in
include/linux/mmc/card.h. If the module parameter is placed in the
kernel command line (or bootargs) stored on the card then, assuming the
device only has one SD card interface, the override effectively becomes
card-specific.
Phil Elwell [Wed, 25 Mar 2015 17:49:47 +0000 (17:49 +0000)]
Adding bcm2835-sdhost driver, and an overlay to enable it
BCM2835 has two SD card interfaces. This driver uses the other one.
bcm2835-sdhost: Error handling fix, and code clarification
bcm2835-sdhost: Adding overclocking option
Allow a different clock speed to be substitued for a requested 50MHz.
This option is exposed using the "overclock_50" DT parameter.
Note that the sdhost interface is restricted to integer divisions of
core_freq, and the highest sensible option for a core_freq of 250MHz
is 84 (250/3 = 83.3MHz), the next being 125 (250/2) which is much too
high.
Use at your own risk.
bcm2835-sdhost: Round up the overclock, so 62 works for 62.5Mhz
Also only warn once for each overclock setting.
bcm2835-sdhost: Improve error handling and recovery
1) Expose the hw_reset method to the MMC framework, removing many
internal calls by the driver.
2) Reduce overclock setting on error.
3) Increase timeout to cope with high capacity cards.
4) Add properties and parameters to control pio_limit and debug.
5) Reduce messages at probe time.
bcm2835-sdhost: Further improve overclock back-off
It seems that the sdhost interface returns CRC7 errors for CMD1,
which is the MMC-specific SEND_OP_COND. Returning these errors to
the MMC layer causes a downward spiral, but ignoring them seems
to be harmless.
The bcm2835-mmc driver (and -sdhost driver that copied from it)
contains code to handle SDIO interrupts in a threaded interrupt
handler rather than waking the MMC framework thread. The change
follows a patch from Russell King that adds the facility as the
preferred way of working.
However, the new code path is only present in ARCH_BCM2835
builds, which I have taken to be a way of testing the waters
rather than making the change across the board; I can't see
any technical reason why it wouldn't be enabled for MACH_BCM270X
builds. So this patch standardises on the ARCH_BCM2835 code,
removing the old code paths.
The MMC card-discovery process generates timeouts. This is
expected behaviour, so reporting it to the user serves no purpose.
Suppress the reporting of timeout errors unless the debug flag
is on.
bcm2835-sdhost: Add workaround for odd behaviour on some cards
For reasons not understood, the sdhost driver fails when reading
sectors very near the end of some SD cards. The problem could
be related to the similar issue that reading the final sector
of any card as part of a multiple read never completes, and the
workaround is an extension of the mechanism introduced to solve
that problem which ensures those sectors are always read singly.
bcm2835-sdhost: Major revision
This is a significant revision of the bcm2835-sdhost driver. It
improves on the original in a number of ways:
1) Through the use of CMD23 for reads it appears to avoid problems
reading some sectors on certain high speed cards.
2) Better atomicity to prevent crashes.
3) Higher performance.
4) Activity logging included, for easier diagnosis in the event
of a problem.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: Restore ATOMIC flag to PIO sg mapping
Allocation problems have been seen in a wireless driver, and
this is the only change which might have been responsible.
SQUASH: bcm2835-sdhost: Only claim one DMA channel
With both MMC controllers enabled there are few DMA channels left. The
bcm2835-sdhost driver only uses DMA in one direction at a time, so it
doesn't need to claim two channels.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: Workaround for "slow" sectors
Some cards have been seen to cause timeouts after certain sectors are
read. This workaround enforces a minimum delay between the stop after
reading one of those sectors and a subsequent data command.
Using CMD23 (SET_BLOCK_COUNT) avoids this problem, so good cards will
not be penalised by this workaround.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: Firmware manages the clock divisor
The bcm2835-sdhost driver hands control of the CDIV clock divisor
register to matching firmware, allowing it to adjust to a changing
core clock. This removes the need to use the performance governor or
to enable io_is_busy on the on-demand governor in order to get the
best SD performance.
N.B. As SD clocks must be an integer divisor of the core clock, it is
possible that the SD clock for "turbo" mode can be different (even
lower) than "normal" mode.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: Reset the clock in task context
Since reprogramming the clock can now involve a round-trip to the
firmware it must not be done at atomic context, and a tasklet
is not a task.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: Don't exit cmd wait loop on error
The FAIL flag can be set in the CMD register before command processing
is complete, leading to spurious "failed to complete" errors. This has
the effect of promoting harmless CRC7 errors during CMD1 processing
into errors that can delay and even prevent booting.
Also:
1) Convert the last KERN_ERROR message in the register dumping to
KERN_INFO.
2) Remove an unnecessary reset call from bcm2835_sdhost_add_host.
gellert [Fri, 15 Aug 2014 15:35:06 +0000 (16:35 +0100)]
MMC: added alternative MMC driver
mmc: Disable CMD23 transfers on all cards
Pending wire-level investigation of these types of transfers
and associated errors on bcm2835-mmc, disable for now. Fallback of
CMD18/CMD25 transfers will be used automatically by the MMC layer.
Probe error handling is broken in several places.
Simplify error handling by using device managed functions.
Replace pr_{err,info} with dev_{err,info}.
bcm2835-mmc: Add range of debug options for slowing things down
bcm2835-mmc: Add option to disable some delays
bcm2835-mmc: Add option to disable MMC_QUIRK_BLK_NO_CMD23
bcm2835-mmc: Default to disabling MMC_QUIRK_BLK_NO_CMD23
bcm2835-mmc: Adding overclocking option
Allow a different clock speed to be substitued for a requested 50MHz.
This option is exposed using the "overclock_50" DT parameter.
Note that the mmc interface is restricted to EVEN integer divisions of
250MHz, and the highest sensible option is 63 (250/4 = 62.5), the
next being 125 (250/2) which is much too high.
Use at your own risk.
bcm2835-mmc: Round up the overclock, so 62 works for 62.5Mhz
Also only warn once for each overclock setting.
mmc: bcm2835-mmc: Make available on ARCH_BCM2835
Make the bcm2835-mmc driver available for use on ARCH_BCM2835.
bcm2835-mmc: Don't override bus width capabilities from devicetree
Take out the force setting of the MMC_CAP_4_BIT_DATA host capability
so that the result read from devicetree via mmc_of_parse() is
preserved.
bcm2835-mmc: Only claim one DMA channel
With both MMC controllers enabled there are few DMA channels left. The
bcm2835-mmc driver only uses DMA in one direction at a time, so it
doesn't need to claim two channels.
Florian Meier [Fri, 22 Nov 2013 13:22:53 +0000 (14:22 +0100)]
dmaengine: Add support for BCM2708
Add support for DMA controller of BCM2708 as used in the Raspberry Pi.
Currently it only supports cyclic DMA.
Signed-off-by: Florian Meier <florian.meier@koalo.de>
dmaengine: expand functionality by supporting scatter/gather transfers sdhci-bcm2708 and dma.c: fix for LITE channels
DMA: fix cyclic LITE length overflow bug
dmaengine: bcm2708: Remove chancnt affectations
Mirror bcm2835-dma.c commit 9eba5536a7434c69d8c185d4bd1c70734d92287d:
chancnt is already filled by dma_async_device_register, which uses the channel
list to know how much channels there is.
Since it's already filled, we can safely remove it from the drivers' probe
function.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: overwrite dreq only if it is not set
dreq is set when the DMA channel is fetched from Device Tree.
slave_id is set using dmaengine_slave_config().
Only overwrite dreq with slave_id if it is not set.
dreq/slave_id in the cyclic DMA case is not touched, because I don't
have hardware to test with.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: do device registration in the board file
Don't register the device in the driver. Do it in the board file.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: don't restrict DT support to ARCH_BCM2835
Both ARCH_BCM2835 and ARCH_BCM270x are built with OF now.
Add Device Tree support to the non ARCH_BCM2835 case.
Use the same driver name regardless of architecture.
Add Device Tree entry for bcm2835-dma.
The entry doesn't contain any resources since they are handled
by the arch/arm/mach-bcm270x/dma.c driver.
In non-DT mode, don't add the device in the board file.
BCM270x: Add memory and irq resources to dmaengine device and DT
Prepare for merging of the legacy DMA API arch driver dma.c
with bcm2708-dmaengine by adding memory and irq resources both
to platform file device and Device Tree node.
Don't use BCM_DMAMAN_DRIVER_NAME so we don't have to include mach/dma.h
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: Merge with arch dma.c driver and disable dma.c
Merge the legacy DMA API driver with bcm2708-dmaengine.
This is done so we can use bcm2708_fb on ARCH_BCM2835 (mailbox
driver is also needed).
Changes to the dma.c code:
- Use BIT() macro.
- Cutdown some comments to one line.
- Add mutex to vc_dmaman and use this, since the dev lock is locked
during probing of the engine part.
- Add global g_dmaman variable since drvdata is used by the engine part.
- Restructure for readability:
vc_dmaman_chan_alloc()
vc_dmaman_chan_free()
bcm_dma_chan_free()
- Restructure bcm_dma_chan_alloc() to simplify error handling.
- Use device irq resources instead of hardcoded bcm_dma_irqs table.
- Remove dev_dmaman_register() and code it directly.
- Remove dev_dmaman_deregister() and code it directly.
- Simplify bcm_dmaman_probe() using devm_* functions.
- Get dmachans from DT if available.
- Keep 'dma.dmachans' module argument name for backwards compatibility.
Make it available on ARCH_BCM2835 as well.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: set residue_granularity field
bcm2708-dmaengine supports residue reporting at burst level
but didn't report this via the residue_granularity field.
Without this field set properly we get playback issues with I2S cards.
dmaengine: bcm2708-dmaengine: Fix memory leak when stopping a running transfer
bcm2708-dmaengine: Use more DMA channels (but not 12)
1) Only the bcm2708_fb drivers uses the legacy DMA API, and
it requires a BULK-capable channel, so all other types
(FAST, NORMAL and LITE) can be made available to the regular
DMA API.
2) DMA channels 11-14 share an interrupt. The driver can't
handle this, so don't use channels 12-14 (12 was used, probably
because it appears to have an interrupt, but in reality that
interrupt is for activity on ANY channel). This may explain
a lockup encountered when running out of DMA channels.
The combined effect of this patch is to leave 7 DMA channels
available + channel 0 for bcm2708_fb via the legacy API.
dmaengine: bcm2708: Make legacy API available for bcm2835-dma
bcm2708_fb uses the legacy DMA API, so in order to start using
bcm2835-dma, bcm2835-dma has to support the legacy API. Make this
possible by exporting bcm_dmaman_probe() and bcm_dmaman_remove().
popcornmix [Wed, 17 Jun 2015 16:06:34 +0000 (17:06 +0100)]
bcm2708 framebuffer driver
Signed-off-by: popcornmix <popcornmix@gmail.com>
bcm2708_fb : Implement blanking support using the mailbox property interface
bcm2708_fb: Add pan and vsync controls
bcm2708_fb: DMA acceleration for fb_copyarea
Based on http://www.raspberrypi.org/phpBB3/viewtopic.php?p=62425#p62425
Also used Simon's dmaer_master module as a reference for tweaking DMA
settings for better performance.
For now busylooping only. IRQ support might be added later.
With non-overclocked Raspberry Pi, the performance is ~360 MB/s
for simple copy or ~260 MB/s for two-pass copy (used when dragging
windows to the right).
In the case of using DMA channel 0, the performance improves
to ~440 MB/s.
For comparison, VFP optimized CPU copy can only do ~114 MB/s in
the same conditions (hindered by reading uncached source buffer).
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
bcm2708_fb: report number of dma copies
Add a counter (exported via debugfs) reporting the
number of dma copies that the framebuffer driver
has done, in order to help evaluate different
optimization strategies.
Signed-off-by: Luke Diamand <luked@broadcom.com>
bcm2708_fb: use IRQ for DMA copies
The copyarea ioctl() uses DMA to speed things along. This
was busy-waiting for completion. This change supports using
an interrupt instead for larger transfers. For small
transfers, busy-waiting is still likely to be faster.
Signed-off-by: Luke Diamand <luke@diamand.org>
bcm2708: Make ioctl logging quieter
video: fbdev: bcm2708_fb: Don't panic on error
No need to panic the kernel if the video driver fails.
Just print a message and return an error.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
fbdev: bcm2708_fb: Add ARCH_BCM2835 support
Add Device Tree support.
Pass the device to dma_alloc_coherent() in order to get the
correct bus address on ARCH_BCM2835.
Use the new DMA legacy API header file.
Including <mach/platform.h> is not necessary.
Signed-off-by: Kari Suvanto <karis79@gmail.com>
usb: dwc: fix inconsistent lock state
Signed-off-by: Kari Suvanto <karis79@gmail.com>
Add FIQ patch to dwc_otg driver. Enable with dwc_otg.fiq_fix_enable=1. Should give about 10% more ARM performance.
Thanks to Gordon and Costas
Avoid dynamic memory allocation for channel lock in USB driver. Thanks ddv2005.
Add NAK holdoff scheme. Enabled by default, disable with dwc_otg.nak_holdoff_enable=0. Thanks gsh
Make sure we wait for the reset to finish
dwc_otg: fix bug in dwc_otg_hcd.c resulting in silent kernel
memory corruption, escalating to OOPS under high USB load.
dwc_otg: Fix unsafe access of QTD during URB enqueue
In dwc_otg_hcd_urb_enqueue during qtd creation, it was possible that the
transaction could complete almost immediately after the qtd was assigned
to a host channel during URB enqueue, which meant the qtd pointer was no
longer valid having been completed and removed. Usually, this resulted in
an OOPS during URB submission. By predetermining whether transactions
need to be queued or not, this unsafe pointer access is avoided.
This bug was only evident on the Pi model A where a device was attached
that had no periodic endpoints (e.g. USB pendrive or some wlan devices).
If the memory allocation for a dwc_otg_urb failed, the kernel would OOPS
because for some reason a member of the *unallocated* struct was set to
zero. Error handling changed to fail correctly.
dwc_otg: fix potential use-after-free case in interrupt handler
If a transaction had previously aborted, certain interrupts are
enabled to track error counts and reset where necessary. On IN
endpoints the host generates an ACK interrupt near-simultaneously
with completion of transfer. In the case where this transfer had
previously had an error, this results in a use-after-free on
the QTD memory space with a 1-byte length being overwritten to
0x00.
dwc_otg: add handling of SPLIT transaction data toggle errors
Previously a data toggle error on packets from a USB1.1 device behind
a TT would result in the Pi locking up as the driver never handled
the associated interrupt. Patch adds basic retry mechanism and
interrupt acknowledgement to cater for either a chance toggle error or
for devices that have a broken initial toggle state (FT8U232/FT232BM).
dwc_otg: implement tasklet for returning URBs to usbcore hcd layer
The dwc_otg driver interrupt handler for transfer completion will spend
a very long time with interrupts disabled when a URB is completed -
this is because usb_hcd_giveback_urb is called from within the handler
which for a USB device driver with complicated processing (e.g. webcam)
will take an exorbitant amount of time to complete. This results in
missed completion interrupts for other USB packets which lead to them
being dropped due to microframe overruns.
This patch splits returning the URB to the usb hcd layer into a
high-priority tasklet. This will have most benefit for isochronous IN
transfers but will also have incidental benefit where multiple periodic
devices are active at once.
dwc_otg: fix NAK holdoff and allow on split transactions only
This corrects a bug where if a single active non-periodic endpoint
had at least one transaction in its qh, on frnum == MAX_FRNUM the qh
would get skipped and never get queued again. This would result in
a silent device until error detection (automatic or otherwise) would
either reset the device or flush and requeue the URBs.
Additionally the NAK holdoff was enabled for all transactions - this
would potentially stall a HS endpoint for 1ms if a previous error state
enabled this interrupt and the next response was a NAK. Fix so that
only split transactions get held off.
dwc_otg: Call usb_hcd_unlink_urb_from_ep with lock held in completion handler
usb_hcd_unlink_urb_from_ep must be called with the HCD lock held. Calling it
asynchronously in the tasklet was not safe (regression in c4564d4a1a0a9b10d4419e48239f5d99e88d2667).
This change unlinks it from the endpoint prior to queueing it for handling in
the tasklet, and also adds a check to ensure the urb is OK to be unlinked
before doing so.
NULL pointer dereference kernel oopses had been observed in usb_hcd_giveback_urb
when a USB device was unplugged/replugged during data transfer. This effect
was reproduced using automated USB port power control, hundreds of replug
events were performed during active transfers to confirm that the problem was
eliminated.
USB fix using a FIQ to implement split transactions
This commit adds a FIQ implementaion that schedules
the split transactions using a FIQ so we don't get
held off by the interrupt latency of Linux
dwc_otg: fix device attributes and avoid kernel warnings on boot
dcw_otg: avoid logging function that can cause panics
See: https://github.com/raspberrypi/firmware/issues/21
Thanks to cleverca22 for fix
dwc_otg: mask correct interrupts after transaction error recovery
The dwc_otg driver will unmask certain interrupts on a transaction
that previously halted in the error state in order to reset the
QTD error count. The various fine-grained interrupt handlers do not
consider that other interrupts besides themselves were unmasked.
By disabling the two other interrupts only ever enabled in DMA mode
for this purpose, we can avoid unnecessary function calls in the
IRQ handler. This will also prevent an unneccesary FIQ interrupt
from being generated if the FIQ is enabled.
dwc_otg: fiq: prevent FIQ thrash and incorrect state passing to IRQ
In the case of a transaction to a device that had previously aborted
due to an error, several interrupts are enabled to reset the error
count when a device responds. This has the side-effect of making the
FIQ thrash because the hardware will generate multiple instances of
a NAK on an IN bulk/interrupt endpoint and multiple instances of ACK
on an OUT bulk/interrupt endpoint. Make the FIQ mask and clear the
associated interrupts.
Additionally, on non-split transactions make sure that only unmasked
interrupts are cleared. This caused a hard-to-trigger but serious
race condition when you had the combination of an endpoint awaiting
error recovery and a transaction completed on an endpoint - due to
the sequencing and timing of interrupts generated by the dwc_otg core,
it was possible to confuse the IRQ handler.
Fix function tracing
dwc_otg: whitespace cleanup in dwc_otg_urb_enqueue
dwc_otg: prevent OOPSes during device disconnects
The dwc_otg_urb_enqueue function is thread-unsafe. In particular the
access of urb->hcpriv, usb_hcd_link_urb_to_ep, dwc_otg_urb->qtd and
friends does not occur within a critical section and so if a device
was unplugged during activity there was a high chance that the
usbcore hub_thread would try to disable the endpoint with partially-
formed entries in the URB queue. This would result in BUG() or null
pointer dereferences.
Fix so that access of urb->hcpriv, enqueuing to the hardware and
adding to usbcore endpoint URB lists is contained within a single
critical section.
dwc_otg: prevent BUG() in TT allocation if hub address is > 16
A fixed-size array is used to track TT allocation. This was
previously set to 16 which caused a crash because
dwc_otg_hcd_allocate_port would read past the end of the array.
This was hit if a hub was plugged in which enumerated as addr > 16,
due to previous device resets or unplugs.
Also add #ifdef FIQ_DEBUG around hcd->hub_port_alloc[], which grows
to a large size if 128 hub addresses are supported. This field is
for debug only for tracking which frame an allocate happened in.
dwc_otg: make channel halts with unknown state less damaging
If the IRQ received a channel halt interrupt through the FIQ
with no other bits set, the IRQ would not release the host
channel and never complete the URB.
Add catchall handling to treat as a transaction error and retry.
dwc_otg: fiq_split: use TTs with more granularity
This fixes certain issues with split transaction scheduling.
- Isochronous multi-packet OUT transactions now hog the TT until
they are completed - this prevents hubs aborting transactions
if they get a periodic start-split out-of-order
- Don't perform TT allocation on non-periodic endpoints - this
allows simultaneous use of the TT's bulk/control and periodic
transaction buffers
This commit will mainly affect USB audio playback.
dwc_otg: fix potential sleep while atomic during urb enqueue
Fixes a regression introduced with eb1b482a. Kmalloc called from
dwc_otg_hcd_qtd_add / dwc_otg_hcd_qtd_create did not always have
the GPF_ATOMIC flag set. Force this flag when inside the larger
critical section.
dwc_otg: make fiq_split_enable imply fiq_fix_enable
Failing to set up the FIQ correctly would result in
"IRQ 32: nobody cared" errors in dmesg.
dwc_otg: prevent crashes on host port disconnects
Fix several issues resulting in crashes or inconsistent state
if a Model A root port was disconnected.
- Clean up queue heads properly in kill_urbs_in_qh_list by
removing the empty QHs from the schedule lists
- Set the halt status properly to prevent IRQ handlers from
using freed memory
- Add fiq_split related cleanup for saved registers
- Make microframe scheduling reclaim host channels if
active during a disconnect
- Abort URBs with -ESHUTDOWN status response, informing
device drivers so they respond in a more correct fashion
and don't try to resubmit URBs
- Prevent IRQ handlers from attempting to handle channel
interrupts if the associated URB was dequeued (and the
driver state was cleared)
dwc_otg: prevent leaking URBs during enqueue
A dwc_otg_urb would get leaked if the HCD enqueue function
failed for any reason. Free the URB at the appropriate points.
dwc_otg: Enable NAK holdoff for control split transactions
Certain low-speed devices take a very long time to complete a
data or status stage of a control transaction, producing NAK
responses until they complete internal processing - the USB2.0
spec limit is up to 500mS. This causes the same type of interrupt
storm as seen with USB-serial dongles prior to c8edb238.
In certain circumstances, usually while booting, this interrupt
storm could cause SD card timeouts.
dwc_otg: Fix for occasional lockup on boot when doing a USB reset
dwc_otg: Don't issue traffic to LS devices in FS mode
Issuing low-speed packets when the root port is in full-speed mode
causes the root port to stop responding. Explicitly fail when
enqueuing URBs to a LS endpoint on a FS bus.
Fix ARM architecture issue with local_irq_restore()
If local_fiq_enable() is called before a local_irq_restore(flags) where
the flags variable has the F bit set, the FIQ will be erroneously disabled.
Fixup arch_local_irq_restore to avoid trampling the F bit in CPSR.
Also fix some of the hacks previously implemented for previous dwc_otg
incarnations.
dwc_otg: fiq_fsm: Base commit for driver rewrite
This commit removes the previous FIQ fixes entirely and adds fiq_fsm.
This rewrite features much more complete support for split transactions
and takes into account several OTG hardware bugs. High-speed
isochronous transactions are also capable of being performed by fiq_fsm.
All driver options have been removed and replaced with:
- dwc_otg.fiq_enable (bool)
- dwc_otg.fiq_fsm_enable (bool)
- dwc_otg.fiq_fsm_mask (bitmask)
- dwc_otg.nak_holdoff (unsigned int)
Defaults are specified such that fiq_fsm behaves similarly to the
previously implemented FIQ fixes.
fiq_fsm: Push error recovery into the FIQ when fiq_fsm is used
If the transfer associated with a QTD failed due to a bus error, the HCD
would retry the transfer up to 3 times (implementing the USB2.0
three-strikes retry in software).
Due to the masking mechanism used by fiq_fsm, it is only possible to pass
a single interrupt through to the HCD per-transfer.
In this instance host channels would fall off the radar because the error
reset would function, but the subsequent channel halt would be lost.
Push the error count reset into the FIQ handler.
fiq_fsm: Implement timeout mechanism
For full-speed endpoints with a large packet size, interrupt latency
runs the risk of the FIQ starting a transaction too late in a full-speed
frame. If the device is still transmitting data when EOF2 for the
downstream frame occurs, the hub will disable the port. This change is
not reflected in the hub status endpoint and the device becomes
unresponsive.
Prevent high-bandwidth transactions from being started too late in a
frame. The mechanism is not guaranteed: a combination of bit stuffing
and hub latency may still result in a device overrunning.
fiq_fsm: fix bounce buffer utilisation for Isochronous OUT
Multi-packet isochronous OUT transactions were subject to a few bounday
bugs. Fix them.
Audio playback is now much more robust: however, an issue stands with
devices that have adaptive sinks - ALSA plays samples too fast.
dwc_otg: Return full-speed frame numbers in HS mode
The frame counter increments on every *microframe* in high-speed mode.
Most device drivers expect this number to be in full-speed frames - this
caused considerable confusion to e.g. snd_usb_audio which uses the
frame counter to estimate the number of samples played.
fiq_fsm: save PID on completion of interrupt OUT transfers
Also add edge case handling for interrupt transports.
Note that for periodic split IN, data toggles are unimplemented in the
OTG host hardware - it unconditionally accepts any PID.
fiq_fsm: add missing case for fiq_fsm_tt_in_use()
Certain combinations of bitrate and endpoint activity could
result in a periodic transaction erroneously getting started
while the previous Isochronous OUT was still active.
fiq_fsm: clear hcintmsk for aborted transactions
Prevents the FIQ from erroneously handling interrupts
on a timed out channel.
fiq_fsm: enable by default
fiq_fsm: fix dequeues for non-periodic split transactions
If a dequeue happened between the SSPLIT and CSPLIT phases of the
transaction, the HCD would never receive an interrupt.
fiq_fsm: Disable by default
fiq_fsm: Handle HC babble errors
The HCTSIZ transfer size field raises a babble interrupt if
the counter wraps. Handle the resulting interrupt in this case.
dwc_otg: fix interrupt registration for fiq_enable=0
Additionally make the module parameter conditional for wherever
hcd->fiq_state is touched.
fiq_fsm: Enable by default
dwc_otg: Fix various issues with root port and transaction errors
Process the host port interrupts correctly (and don't trample them).
Root port hotplug now functional again.
Fix a few thinkos with the transaction error passthrough for fiq_fsm.
fiq_fsm: Implement hack for Split Interrupt transactions
Hubs aren't too picky about which endpoint we send Control type split
transactions to. By treating Interrupt transfers as Control, it is
possible to use the non-periodic queue in the OTG core as well as the
non-periodic FIFOs in the hub itself. This massively reduces the
microframe exclusivity/contention that periodic split transactions
otherwise have to enforce.
It goes without saying that this is a fairly egregious USB specification
violation, but it works.
Original idea by Hans Petter Selasky @ FreeBSD.org.
dwc_otg: FIQ support on SMP. Set up FIQ stack and handler on Core 0 only.
dwc_otg: introduce fiq_fsm_spin(un|)lock()
SMP safety for the FIQ relies on register read-modify write cycles being
completed in the correct order. Several places in the DWC code modify
registers also touched by the FIQ. Protect these by a bare-bones lock
mechanism.
This also makes it possible to run the FIQ and IRQ handlers on different
cores.
fiq_fsm: fix build on bcm2708 and bcm2709 platforms
dwc_otg: put some barriers back where they should be for UP
bcm2709/dwc_otg: Setup FIQ on core 1 if >1 core active
dwc_otg: fixup read-modify-write in critical paths
Be more careful about read-modify-write on registers that the FIQ
also touches.
Guard fiq_fsm_spin_lock with fiq_enable check
fiq_fsm: Falling out of the state machine isn't fatal
This edge case can be hit if the port is disabled while the FIQ is
in the middle of a transaction. Make the effects less severe.
Also get rid of the useless return value.
squash: dwc_otg: Allow to build without SMP
usb: core: make overcurrent messages more prominent
Hub overcurrent messages are more serious than "debug". Increase loglevel.
usb: dwc_otg: Don't use dma_to_virt()
Commit 6ce0d20 changes dma_to_virt() which breaks this driver.
Open code the old dma_to_virt() implementation to work around this.
Limit the use of __bus_to_virt() to cases where transfer_buffer_length
is set and transfer_buffer is not set. This is done to increase the
chance that this driver will also work on ARCH_BCM2835.
transfer_buffer should not be NULL if the length is set, but the
comment in the code indicates that there are situations where this
might happen. drivers/usb/isp1760/isp1760-hcd.c also has a similar
comment pointing to a possible: 'usb storage / SCSI bug'.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dwc_otg: Fix crash when fiq_enable=0
dwc_otg: fiq_fsm: Make high-speed isochronous strided transfers work properly
Certain low-bandwidth high-speed USB devices (specialist audio devices,
compressed-frame webcams) have packet intervals > 1 microframe.
Stride these transfers in the FIQ by using the start-of-frame interrupt
to restart the channel at the right time.
dwc_otg: Force host mode to fix incorrect compute module boards
dwc_otg: Add ARCH_BCM2835 support
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dwc_otg: Simplify FIQ irq number code
Dropping ATAGS means we can simplify the FIQ irq number code.
Also add error checking on the returned irq number.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dwc_otg: Remove duplicate gadget probe/unregister function
dwc_otg: Properly set the HFIR
Douglas Anderson reported:
According to the most up to date version of the dwc2 databook, the FRINT
field of the HFIR register should be programmed to:
* 125 us * (PHY clock freq for HS) - 1
* 1000 us * (PHY clock freq for FS/LS) - 1
This is opposed to older versions of the doc that claimed it should be:
* 125 us * (PHY clock freq for HS)
* 1000 us * (PHY clock freq for FS/LS)
and reported lower timing jitter on a USB analyser
dcw_otg: trim xfer length when buffer larger than allocated size is received
dwc_otg: Don't free qh align buffers in atomic context
dwc_otg: Enable the hack for Split Interrupt transactions by default
dwc_otg.fiq_fsm_mask=0xF has long been a suggestion for users with audio stutters or other USB bandwidth issues.
So far we are aware of many success stories but no failure caused by this setting.
Make it a default to learn more.
Martin Sperl [Fri, 2 Sep 2016 15:45:27 +0000 (16:45 +0100)]
Register the clocks early during the boot process,
so that special/critical clocks can get enabled early on
in the boot process avoiding the risk of disabling a clock,
pll_divider or pll when a claiming driver fails to install
propperly - maybe it needs to defer.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Noralf Trønnes [Fri, 7 Oct 2016 14:50:59 +0000 (16:50 +0200)]
watchdog: bcm2835: Support setting reboot partition
The Raspberry Pi firmware looks at the RSTS register to know which
partition to boot from. The reboot syscall command
LINUX_REBOOT_CMD_RESTART2 supports passing in a string argument.
Add support for passing in a partition number 0..63 to boot from.
Partition 63 is a special partiton indicating halt.
If the partition doesn't exist, the firmware falls back to partition 0.
Noralf Trønnes [Sat, 3 Oct 2015 20:22:55 +0000 (22:22 +0200)]
dmaengine: bcm2835: Load driver early and support legacy API
Load driver early since at least bcm2708_fb doesn't support deferred
probing and even if it did, we don't want the video driver deferred.
Support the legacy DMA API which is needed by bcm2708_fb.
Don't mask out channel 2.
Noralf Trønnes [Wed, 3 Jun 2015 10:26:13 +0000 (12:26 +0200)]
ARM: bcm2835: Set Serial number and Revision
The VideoCore bootloader passes in Serial number and
Revision number through Device Tree. Make these available to
userspace through /proc/cpuinfo.
Mainline status:
There is a commit in linux-next that standardize passing the serial
number through Device Tree (string: /serial-number):
ARM: 8355/1: arch: Show the serial number from devicetree in cpuinfo
There was an attempt to do the same with the revision number, but it
didn't get in:
[PATCH v2 1/2] arm: devtree: Set system_rev from DT revision
Phil Elwell [Wed, 24 Jun 2015 13:10:44 +0000 (14:10 +0100)]
spi-bcm2835: Support pin groups other than 7-11
The spi-bcm2835 driver automatically uses GPIO chip-selects due to
some unreliability of the native ones. In doing so it chooses the
same pins as the native chip-selects would use, but the existing
code always uses pins 7 and 8, wherever the SPI function is mapped.
Search the pinctrl group assigned to the driver for pins that
correspond to native chip-selects, and use those for GPIO chip-
selects.
Phil Elwell [Thu, 26 Feb 2015 09:58:22 +0000 (09:58 +0000)]
pinctrl-bcm2835: Only request the interrupts listed in the DTB
Although the GPIO controller can generate three interrupts (four counting
the common one), the device tree files currently only specify two. In the
absence of the third, simply don't register that interrupt (as opposed to
registering 0), which has the effect of making it impossible to generate
interrupts for GPIOs 46-53 which, since they share pins with the SD card
interface, is unlikely to be a problem.
Noralf Trønnes [Fri, 12 Jun 2015 17:01:05 +0000 (19:01 +0200)]
irqchip: bcm2835: Add FIQ support
Add a duplicate irq range with an offset on the hwirq's so the
driver can detect that enable_fiq() is used.
Tested with downstream dwc_otg USB controller driver.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org> Reviewed-by: Eric Anholt <eric@anholt.net> Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Phil Elwell [Fri, 4 Dec 2015 17:41:50 +0000 (17:41 +0000)]
irq-bcm2836: Prevent spurious interrupts, and trap them early
The old arch-specific IRQ macros included a dsb to ensure the
write to clear the mailbox interrupt completed before returning
from the interrupt. The BCM2836 irqchip driver needs the same
precaution to avoid spurious interrupts.
Spurious interrupts are still possible for other reasons,
though, so trap them early.
Eric Anholt [Fri, 19 Dec 2014 00:07:15 +0000 (16:07 -0800)]
mm: Remove the PFN busy warning
See commit dae803e165a11bc88ca8dbc07a11077caf97bbcb -- the warning is
expected sometimes when using CMA. However, that commit still spams
my kernel log with these warnings.
Willem de Bruijn [Thu, 10 Aug 2017 16:29:19 +0000 (12:29 -0400)]
udp: consistently apply ufo or fragmentation
When iteratively building a UDP datagram with MSG_MORE and that
datagram exceeds MTU, consistently choose UFO or fragmentation.
Once skb_is_gso, always apply ufo. Conversely, once a datagram is
split across multiple skbs, do not consider ufo.
Sendpage already maintains the first invariant, only add the second.
IPv6 does not have a sendpage implementation to modify.
A gso skb must have a partial checksum, do not follow sk_no_check_tx
in udp_send_skb.
Found by syzkaller.
Fixes: e89e9cf539a2 ("[IPv4/IPv6]: UFO Scatter-gather approach") Reported-by: Andrey Konovalov <andreyknvl@google.com> Signed-off-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
CVE-2017-1000112
Willem de Bruijn [Thu, 10 Aug 2017 16:41:58 +0000 (12:41 -0400)]
packet: fix tp_reserve race in packet_set_ring
Updates to tp_reserve can race with reads of the field in
packet_set_ring. Avoid this by holding the socket lock during
updates in setsockopt PACKET_RESERVE.
This bug was discovered by syzkaller.
Fixes: 8913336a7e8d ("packet: add PACKET_RESERVE sockopt") Reported-by: Andrey Konovalov <andreyknvl@google.com> Signed-off-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
CVE-2017-1000111
Marc Zyngier [Fri, 9 Jun 2017 11:49:56 +0000 (12:49 +0100)]
KVM: arm64: Log an error if trapping a write-to-read-only GICv3 access
BugLink: https://bugs.launchpad.net/bugs/1673564
A write-to-read-only GICv3 access should UNDEF at EL1. But since
we're in complete paranoia-land with broken CPUs, let's assume the
worse and gracefully handle the case.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Reviewed-by: Christoffer Dall <cdall@linaro.org> Signed-off-by: Christoffer Dall <cdall@linaro.org>
(backported picked from commit 7b1dba1f7325629427c0e5bdf014159b229d16c8)
[ dannf: Recoded sys_reg_descs[] entries to use pre-SYS_DESC() syntax and
minor context changes. ] Signed-off-by: dann frazier <dann.frazier@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Marc Zyngier [Fri, 9 Jun 2017 11:49:55 +0000 (12:49 +0100)]
KVM: arm64: Log an error if trapping a read-from-write-only GICv3 access
BugLink: https://bugs.launchpad.net/bugs/1673564
A read-from-write-only GICv3 access should UNDEF at EL1. But since
we're in complete paranoia-land with broken CPUs, let's assume the
worse and gracefully handle the case.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Reviewed-by: Christoffer Dall <cdall@linaro.org> Signed-off-by: Christoffer Dall <cdall@linaro.org>
(backported from commit e7f1d1eef482150a64a6e6ad8faf40f8f97eed67)
[ dannf: Dropped hunk in access_pmswinc since WO check wasn't added
until e0443230. Recoded sys_reg_descs[] entries to use pre-SYS_DESC()
syntax. Other context changes. ] Signed-off-by: dann frazier <dann.frazier@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Marc Zyngier [Mon, 27 Mar 2017 16:03:40 +0000 (17:03 +0100)]
arm64: KVM: Make unexpected reads from WO registers inject an undef
BugLink: https://bugs.launchpad.net/bugs/1673564
Reads from write-only system registers are generally confined to
EL1 and not propagated to EL2 (that's what the architecture
mantates). In order to be sure that we have a sane behaviour
even in the unlikely event that we have a broken system, we still
handle it in KVM.
In that case, let's inject an undef into the guest.
Let's also remove write_to_read_only which isn't used anywhere.
Reviewed-by: Christoffer Dall <cdall@linaro.org> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
(cherry picked from commit 7b5b4df1a79954e0b208630fc63b16ec0231a516) Signed-off-by: dann frazier <dann.frazier@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Tested-by: Alexander Graf <agraf@suse.de> Acked-by: David Daney <david.daney@cavium.com> Acked-by: Christoffer Dall <cdall@linaro.org> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Christoffer Dall <cdall@linaro.org>
(cherry picked from commit 2873b5082c5fbe2037f12e8d2abc8ad8f8d82a1b) Signed-off-by: dann frazier <dann.frazier@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Marc Zyngier [Fri, 9 Jun 2017 11:49:53 +0000 (12:49 +0100)]
KVM: arm64: Enable GICv3 common sysreg trapping via command-line
BugLink: https://bugs.launchpad.net/bugs/1673564
Now that we're able to safely handle common sysreg access, let's
give the user the opportunity to enable it by passing a specific
command-line option (vgic_v3.common_trap).
Tested-by: Alexander Graf <agraf@suse.de> Acked-by: David Daney <david.daney@cavium.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Acked-by: Christoffer Dall <cdall@linaro.org> Signed-off-by: Christoffer Dall <cdall@linaro.org>
(cherry picked from commit ff89511ef29b794d6a9c6b62f5ea76fc013cdae7) Signed-off-by: dann frazier <dann.frazier@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Marc Zyngier [Fri, 9 Jun 2017 11:49:52 +0000 (12:49 +0100)]
KVM: arm64: vgic-v3: Add ICV_PMR_EL1 handler
BugLink: https://bugs.launchpad.net/bugs/1673564
Add a handler for reading/writing the guest's view of the ICC_PMR_EL1
register, which is located in the ICH_VMCR_EL2.VPMR field.
Tested-by: Alexander Graf <agraf@suse.de> Acked-by: David Daney <david.daney@cavium.com> Acked-by: Christoffer Dall <cdall@linaro.org> Reviewed-by: Eric Auger <eric.auger@redhat.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Christoffer Dall <cdall@linaro.org>
(backported from commit 6293d6514d6b0945210e15edcecc71d99cfca97c)
[ dannf: Dropped SYS_ prefix on ICC_PMR_EL1 macro, which wasn't
added upstream until 0e9884fe ] Signed-off-by: dann frazier <dann.frazier@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Marc Zyngier [Fri, 9 Jun 2017 11:49:51 +0000 (12:49 +0100)]
KVM: arm64: vgic-v3: Add ICV_CTLR_EL1 handler
BugLink: https://bugs.launchpad.net/bugs/1673564
Add a handler for reading/writing the guest's view of the ICV_CTLR_EL1
register. only EOIMode and CBPR are of interest here, as all the other
bits directly come from ICH_VTR_EL2 and are Read-Only.
Tested-by: Alexander Graf <agraf@suse.de> Acked-by: David Daney <david.daney@cavium.com> Acked-by: Christoffer Dall <cdall@linaro.org> Reviewed-by: Eric Auger <eric.auger@redhat.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Christoffer Dall <cdall@linaro.org>
(backported from commit d840b2d37d3ef2463db38274c6fd72619acbe216)
[ dannf: Dropped SYS_ prefix on ICC_DIR_EL1 macro, which wasn't
added upstream until 0e9884fe ] Signed-off-by: dann frazier <dann.frazier@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Marc Zyngier [Fri, 9 Jun 2017 11:49:50 +0000 (12:49 +0100)]
KVM: arm64: vgic-v3: Add ICV_RPR_EL1 handler
BugLink: https://bugs.launchpad.net/bugs/1673564
Add a handler for reading the guest's view of the ICV_RPR_EL1
register, returning the highest active priority.
Tested-by: Alexander Graf <agraf@suse.de> Acked-by: David Daney <david.daney@cavium.com> Acked-by: Christoffer Dall <cdall@linaro.org> Reviewed-by: Eric Auger <eric.auger@redhat.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Christoffer Dall <cdall@linaro.org>
(backported from commit 43515894c06f856b7743145e002591309f60b247)
[ dannf: Drop the SYS_ prefix and move the ICV_RPR_EL1 macro definition
from asm/sysreg.h to asm/arch_gicv3.h for consistency with code
prior to 0e9884fe ] Signed-off-by: dann frazier <dann.frazier@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Marc Zyngier [Fri, 9 Jun 2017 11:49:49 +0000 (12:49 +0100)]
KVM: arm64: vgic-v3: Add ICV_DIR_EL1 handler
BugLink: https://bugs.launchpad.net/bugs/1673564
Add a handler for writing the guest's view of the ICC_DIR_EL1
register, performing the deactivation of an interrupt if EOImode
is set ot 1.
Tested-by: Alexander Graf <agraf@suse.de> Acked-by: David Daney <david.daney@cavium.com> Reviewed-by: Christoffer Dall <cdall@linaro.org> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Christoffer Dall <cdall@linaro.org>
(backported from commit 40228ba57c8532d4977d684a363915402d85dbf9)
[ dannf: Dropped SYS_ prefix on ICV_DIR_EL1 macro, which wasn't
added upstream until 0e9884fe ] Signed-off-by: dann frazier <dann.frazier@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
David Daney [Fri, 9 Jun 2017 11:49:48 +0000 (12:49 +0100)]
arm64: Add workaround for Cavium Thunder erratum 30115
BugLink: https://bugs.launchpad.net/bugs/1673564
Some Cavium Thunder CPUs suffer a problem where a KVM guest may
inadvertently cause the host kernel to quit receiving interrupts.
Use the Group-0/1 trapping in order to deal with it.
[maz]: Adapted patch to the Group-0/1 trapping, reworked commit log
Tested-by: Alexander Graf <agraf@suse.de> Acked-by: Catalin Marinas <catalin.marinas@arm.com> Reviewed-by: Eric Auger <eric.auger@redhat.com> Signed-off-by: David Daney <david.daney@cavium.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Christoffer Dall <cdall@linaro.org>
(cherry picked from commit 690a341577f9adf2c275ababe0dcefe91898bbf0) Signed-off-by: dann frazier <dann.frazier@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
David Daney [Fri, 9 Jun 2017 11:49:47 +0000 (12:49 +0100)]
arm64: Add MIDR values for Cavium cn83XX SoCs
BugLink: https://bugs.launchpad.net/bugs/1673564 Tested-by: Alexander Graf <agraf@suse.de> Acked-by: David Daney <david.daney@cavium.com> Acked-by: Catalin Marinas <catalin.marinas@arm.com> Reviewed-by: Eric Auger <eric.auger@redhat.com> Signed-off-by: David Daney <david.daney@cavium.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Christoffer Dall <cdall@linaro.org>
(cherry picked from commit e982276d8f5c974b838fb22ba8d592feb039a544) Signed-off-by: dann frazier <dann.frazier@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Marc Zyngier [Fri, 9 Jun 2017 11:49:46 +0000 (12:49 +0100)]
KVM: arm64: Enable GICv3 Group-0 sysreg trapping via command-line
BugLink: https://bugs.launchpad.net/bugs/1673564
Now that we're able to safely handle Group-0 sysreg access, let's
give the user the opportunity to enable it by passing a specific
command-line option (vgic_v3.group0_trap).
Tested-by: Alexander Graf <agraf@suse.de> Acked-by: David Daney <david.daney@cavium.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Christoffer Dall <cdall@linaro.org>
(cherry picked from commit e23f62f76acea232d4def5d4eb21709a2b575f14) Signed-off-by: dann frazier <dann.frazier@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Marc Zyngier [Fri, 9 Jun 2017 11:49:45 +0000 (12:49 +0100)]
KVM: arm64: vgic-v3: Enable trapping of Group-0 system registers
BugLink: https://bugs.launchpad.net/bugs/1673564
In order to be able to trap Group-0 GICv3 system registers, we need to
set ICH_HCR_EL2.TALL0 begore entering the guest. This is conditionnaly
done after having restored the guest's state, and cleared on exit.
Tested-by: Alexander Graf <agraf@suse.de> Acked-by: David Daney <david.daney@cavium.com> Acked-by: Christoffer Dall <cdall@linaro.org> Reviewed-by: Eric Auger <eric.auger@redhat.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Christoffer Dall <cdall@linaro.org>
(backported from commit abf55766f7b062234083ff612446ff8d47e2417e)
[ dannf: context fixes ] Signed-off-by: dann frazier <dann.frazier@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Marc Zyngier [Fri, 9 Jun 2017 11:49:44 +0000 (12:49 +0100)]
KVM: arm64: vgic-v3: Add misc Group-0 handlers
BugLink: https://bugs.launchpad.net/bugs/1673564
A number of Group-0 registers can be handled by the same accessors
as that of Group-1, so let's add the required system register encodings
and catch them in the dispatching function.
Tested-by: Alexander Graf <agraf@suse.de> Acked-by: David Daney <david.daney@cavium.com> Acked-by: Christoffer Dall <cdall@linaro.org> Reviewed-by: Eric Auger <eric.auger@redhat.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Christoffer Dall <cdall@linaro.org>
(backported from commit eab0b2dc4f6f34147e3d10da49ab8032e15dbea0)
[ dannf: Drop the SYS_ prefix and move the system register macro
definitions from asm/sysreg.h to asm/arch_gicv3.h for consistency
with code prior to 0e9884fe ] Signed-off-by: dann frazier <dann.frazier@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Marc Zyngier [Fri, 9 Jun 2017 11:49:43 +0000 (12:49 +0100)]
KVM: arm64: vgic-v3: Add ICV_IGNREN0_EL1 handler
BugLink: https://bugs.launchpad.net/bugs/1673564
Add a handler for reading/writing the guest's view of the ICC_IGRPEN0_EL1
register, which is located in the ICH_VMCR_EL2.VENG0 field.
Tested-by: Alexander Graf <agraf@suse.de> Acked-by: David Daney <david.daney@cavium.com> Reviewed-by: Eric Auger <eric.auger@redhat.com> Reviewed-by: Christoffer Dall <cdall@linaro.org> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Christoffer Dall <cdall@linaro.org>
(backported from commit fbc48a0011deb3d51cb657ca9c0f9083f41c0665)
[ dannf: Drop the SYS_ prefix and move the ICV_IGNREN0_EL1 macro definition
from asm/sysreg.h to asm/arch_gicv3.h for consistency with code
prior to 0e9884fe ] Signed-off-by: dann frazier <dann.frazier@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Marc Zyngier [Fri, 9 Jun 2017 11:49:42 +0000 (12:49 +0100)]
KVM: arm64: vgic-v3: Add ICV_BPR0_EL1 handler
BugLink: https://bugs.launchpad.net/bugs/1673564
Add a handler for reading/writing the guest's view of the ICC_BPR0_EL1
register, which is located in the ICH_VMCR_EL2.BPR0 field.
Tested-by: Alexander Graf <agraf@suse.de> Acked-by: David Daney <david.daney@cavium.com> Reviewed-by: Eric Auger <eric.auger@redhat.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Reviewed-by: Christoffer Dall <cdall@linaro.org> Signed-off-by: Christoffer Dall <cdall@linaro.org>
(backported from commit 423de85a98c2b50715a0784a74f6124fbc0b1548)
[ dannf: Drop the SYS_ prefix and move the ICV_BPR0_EL1 macro definition
from asm/sysreg.h to asm/arch_gicv3.h for consistency with code
prior to 0e9884fe ] Signed-off-by: dann frazier <dann.frazier@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Marc Zyngier [Fri, 9 Jun 2017 11:49:41 +0000 (12:49 +0100)]
KVM: arm64: Enable GICv3 Group-1 sysreg trapping via command-line
BugLink: https://bugs.launchpad.net/bugs/1673564
Now that we're able to safely handle Group-1 sysreg access, let's
give the user the opportunity to enable it by passing a specific
command-line option (vgic_v3.group1_trap).
Tested-by: Alexander Graf <agraf@suse.de> Acked-by: David Daney <david.daney@cavium.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Acked-by: Christoffer Dall <cdall@linaro.org> Signed-off-by: Christoffer Dall <cdall@linaro.org>
(cherry picked from commit 182936eee7e6b1956881b51bc534a541dc71a101) Signed-off-by: dann frazier <dann.frazier@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Marc Zyngier [Fri, 9 Jun 2017 11:49:40 +0000 (12:49 +0100)]
KVM: arm64: vgic-v3: Enable trapping of Group-1 system registers
BugLink: https://bugs.launchpad.net/bugs/1673564
In order to be able to trap Group-1 GICv3 system registers, we need to
set ICH_HCR_EL2.TALL1 before entering the guest. This is conditionally
done after having restored the guest's state, and cleared on exit.
Tested-by: Alexander Graf <agraf@suse.de> Acked-by: David Daney <david.daney@cavium.com> Acked-by: Christoffer Dall <cdall@linaro.org> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Christoffer Dall <cdall@linaro.org>
(backported from commit 9c7bfc288c71068ab323b802dba2eb87fd08b127)
[ dannf: Context adjustments ] Signed-off-by: dann frazier <dann.frazier@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Marc Zyngier [Fri, 9 Jun 2017 11:49:39 +0000 (12:49 +0100)]
KVM: arm64: vgic-v3: Add ICV_HPPIR1_EL1 handler
BugLink: https://bugs.launchpad.net/bugs/1673564
Add a handler for reading the guest's view of the ICV_HPPIR1_EL1
register. This is a simple parsing of the available LRs, extracting the
highest available interrupt.
Tested-by: Alexander Graf <agraf@suse.de> Acked-by: David Daney <david.daney@cavium.com> Reviewed-by: Eric Auger <eric.auger@redhat.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Reviewed-by: Christoffer Dall <cdall@linaro.org> Signed-off-by: Christoffer Dall <cdall@linaro.org>
(backported from commit 2724c11a1df4b22ee966c04809ea0e808f66b04e)
[ dannf: Drop the SYS_ prefix and move the ICV_HPPIR1_EL1 macro definition
from asm/sysreg.h to asm/arch_gicv3.h for consistency with code
prior to 0e9884fe ] Signed-off-by: dann frazier <dann.frazier@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Marc Zyngier [Fri, 9 Jun 2017 11:49:38 +0000 (12:49 +0100)]
KVM: arm64: vgic-v3: Add ICV_AP1Rn_EL1 handler
BugLink: https://bugs.launchpad.net/bugs/1673564
Add a handler for reading/writing the guest's view of the ICV_AP1Rn_EL1
registers. We just map them to the corresponding ICH_AP1Rn_EL2 registers.
Tested-by: Alexander Graf <agraf@suse.de> Acked-by: David Daney <david.daney@cavium.com> Reviewed-by: Eric Auger <eric.auger@redhat.com> Reviewed-by: Christoffer Dall <cdall@linaro.org> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Christoffer Dall <cdall@linaro.org>
(backported from commit f9e7449c780f688bf61a13dfa8c344afeb4ad6e0)
[ dannf: Drop the SYS_ prefix and move the ICV_AP1Rn_EL1 macro definition
from asm/sysreg.h to asm/arch_gicv3.h for consistency with code
prior to 0e9884fe ] Signed-off-by: dann frazier <dann.frazier@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Marc Zyngier [Fri, 9 Jun 2017 11:49:37 +0000 (12:49 +0100)]
KVM: arm64: vgic-v3: Add ICV_EOIR1_EL1 handler
BugLink: https://bugs.launchpad.net/bugs/1673564
Add a handler for writing the guest's view of the ICC_EOIR1_EL1
register. This involves dropping the priority of the interrupt,
and deactivating it if required (EOImode == 0).
Tested-by: Alexander Graf <agraf@suse.de> Acked-by: David Daney <david.daney@cavium.com> Reviewed-by: Eric Auger <eric.auger@redhat.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Reviewed-by: Christoffer Dall <cdall@linaro.org> Signed-off-by: Christoffer Dall <cdall@linaro.org>
(backported from commit b6f49035b4bf6e2709f2a5fed3107f5438c1fd02)
[ dannf: Dropped SYS_ prefix on ICV_EOIR1_EL1 macro, which wasn't
added upstream until 0e9884fe ] Signed-off-by: dann frazier <dann.frazier@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Marc Zyngier [Fri, 9 Jun 2017 11:49:36 +0000 (12:49 +0100)]
KVM: arm64: vgic-v3: Add ICV_IAR1_EL1 handler
BugLink: https://bugs.launchpad.net/bugs/1673564
Add a handler for reading the guest's view of the ICC_IAR1_EL1
register. This involves finding the highest priority Group-1
interrupt, checking against both PMR and the active group
priority, activating the interrupt and setting the group
priority as active.
Tested-by: Alexander Graf <agraf@suse.de> Acked-by: David Daney <david.daney@cavium.com> Reviewed-by: Eric Auger <eric.auger@redhat.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Reviewed-by: Christoffer Dall <cdall@linaro.org> Signed-off-by: Christoffer Dall <cdall@linaro.org>
(backported from commit 132a324ab62fe4fb8d6dcc2ab4eddb0e93b69afe)
[ dannf: Dropped SYS_ prefix on ICV_IAR1_EL1 macro, which wasn't
added upstream until 0e9884fe ] Signed-off-by: dann frazier <dann.frazier@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Marc Zyngier [Fri, 9 Jun 2017 11:49:35 +0000 (12:49 +0100)]
KVM: arm64: vgic-v3: Add ICV_IGRPEN1_EL1 handler
BugLink: https://bugs.launchpad.net/bugs/1673564
Add a handler for reading/writing the guest's view of the ICC_IGRPEN1_EL1
register, which is located in the ICH_VMCR_EL2.VENG1 field.
Tested-by: Alexander Graf <agraf@suse.de> Acked-by: David Daney <david.daney@cavium.com> Reviewed-by: Eric Auger <eric.auger@redhat.com> Reviewed-by: Christoffer Dall <cdall@linaro.org> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Christoffer Dall <cdall@linaro.org>
(backported from commit f8b630bc542e0368886ae193d3519c832b270359)
[ dannf: Dropped SYS_ prefix on ICV_IGRPEN1_EL1 macro, which wasn't
added upstream until 0e9884fe ] Signed-off-by: dann frazier <dann.frazier@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Marc Zyngier [Fri, 9 Jun 2017 11:49:34 +0000 (12:49 +0100)]
KVM: arm64: vgic-v3: Add ICV_BPR1_EL1 handler
BugLink: https://bugs.launchpad.net/bugs/1673564
Add a handler for reading/writing the guest's view of the ICC_BPR1_EL1
register, which is located in the ICH_VMCR_EL2.BPR1 field.
Tested-by: Alexander Graf <agraf@suse.de> Acked-by: David Daney <david.daney@cavium.com> Reviewed-by: Eric Auger <eric.auger@redhat.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Reviewed-by: Christoffer Dall <cdall@linaro.org> Signed-off-by: Christoffer Dall <cdall@linaro.org>
(backported from commit d70c7b31a60f2458f35c226131f2a01a7a98b6cf)
[ dannf: added _vgic_v3_write_vmcr() from 328e5664. Dropped SYS_ prefix
on ICC_BPR1_EL1 macro, which wasn't added upstream until 0e9884fe ] Signed-off-by: dann frazier <dann.frazier@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Marc Zyngier [Fri, 9 Jun 2017 11:49:33 +0000 (12:49 +0100)]
KVM: arm64: vgic-v3: Add hook to handle guest GICv3 sysreg accesses at EL2
BugLink: https://bugs.launchpad.net/bugs/1673564
In order to start handling guest access to GICv3 system registers,
let's add a hook that will get called when we trap a system register
access. This is gated by a new static key (vgic_v3_cpuif_trap).
Tested-by: Alexander Graf <agraf@suse.de> Acked-by: David Daney <david.daney@cavium.com> Reviewed-by: Eric Auger <eric.auger@redhat.com> Reviewed-by: Christoffer Dall <cdall@linaro.org> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Christoffer Dall <cdall@linaro.org>
(cherry picked from commit 59da1cbfd840d69bd7a310249924da3fc202c417)
[ dannf: added _vgic_v3_read_vmcr() from 328e5664 ] Signed-off-by: dann frazier <dann.frazier@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Marc Zyngier [Fri, 9 Jun 2017 11:49:32 +0000 (12:49 +0100)]
KVM: arm64: Make kvm_condition_valid32() accessible from EL2
BugLink: https://bugs.launchpad.net/bugs/1673564
As we're about to trap CP15 accesses and handle them at EL2, we
need to evaluate whether or not the condition flags are valid,
as an implementation is allowed to trap despite the condition
not being met.
Tagging the function as __hyp_text allows this. We still rely on
the cc_map array to be mapped at EL2 by virtue of being "const",
and the linker to only emit relative references.
Tested-by: Alexander Graf <agraf@suse.de> Acked-by: David Daney <david.daney@cavium.com> Reviewed-by: Eric Auger <eric.auger@redhat.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Christoffer Dall <cdall@linaro.org>
(cherry picked from commit 021234ef3752f853704ef1919e8ff33173aca093) Signed-off-by: dann frazier <dann.frazier@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Marc Zyngier [Fri, 9 Jun 2017 11:49:31 +0000 (12:49 +0100)]
KVM: arm/arm64: vgic-v3: Add accessors for the ICH_APxRn_EL2 registers
BugLink: https://bugs.launchpad.net/bugs/1673564
As we're about to access the Active Priority registers a lot more,
let's define accessors that take the register number as a parameter.
Tested-by: Alexander Graf <agraf@suse.de> Acked-by: David Daney <david.daney@cavium.com> Reviewed-by: Eric Auger <eric.auger@redhat.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Christoffer Dall <cdall@linaro.org>
(backported from commit 63000dd8006dc987db31ba670edc23142ea91e01)
[ dannf: trivial context fix ] Signed-off-by: dann frazier <dann.frazier@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Marc Zyngier [Fri, 9 Jun 2017 11:49:30 +0000 (12:49 +0100)]
arm64: Add a facility to turn an ESR syndrome into a sysreg encoding
BugLink: https://bugs.launchpad.net/bugs/1673564
It is often useful to compare an ESR syndrome reporting the trapping
of a system register with a value matching that system register.
Since encoding both the sysreg and the ESR version seem to be a bit
overkill, let's add a set of macros that convert an ESR value into
the corresponding sysreg encoding.
We handle both AArch32 and AArch64, taking advantage of identical
encodings between system registers and CP15 accessors.
Tested-by: Alexander Graf <agraf@suse.de> Acked-by: David Daney <david.daney@cavium.com> Acked-by: Mark Rutland <mark.rutland@arm.com> Acked-by: Catalin Marinas <catalin.marinas@arm.com> Reviewed-by: Eric Auger <eric.auger@redhat.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Christoffer Dall <cdall@linaro.org>
(cherry picked from commit d251f67a187c987b391751849c266e44d69bd31c) Signed-off-by: dann frazier <dann.frazier@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
BugLink: https://bugs.launchpad.net/bugs/1673564
We used to extract PRIbits from the ICH_VT_EL2 which was the upper field
in the register word, so a mask wasn't necessary, but as we switched to
looking at PREbits, which is bits 26 through 28 with the PRIbits field
being potentially non-zero, we really need to mask off the field value,
otherwise fun things may happen.
Signed-off-by: Christoffer Dall <cdall@linaro.org> Acked-by: Marc Zyngier <marc.zyngier@arm.com>
(cherry picked from commit d68356cc51e304ff9a389f006b6249d41f2c2319) Signed-off-by: dann frazier <dann.frazier@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Marc Zyngier [Tue, 2 May 2017 13:30:41 +0000 (14:30 +0100)]
KVM: arm/arm64: vgic-v3: Use PREbits to infer the number of ICH_APxRn_EL2 registers
BugLink: https://bugs.launchpad.net/bugs/1673564
The GICv3 documentation is extremely confusing, as it talks about
the number of priorities represented by the ICH_APxRn_EL2 registers,
while it should really talk about the number of preemption levels.
This leads to a bug where we may access undefined ICH_APxRn_EL2
registers, since PREbits is allowed to be smaller than PRIbits.
Thankfully, nobody seem to have taken this path so far...
The fix is to use ICH_VTR_EL2.PREbits instead.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Reviewed-by: Christoffer Dall <cdall@linaro.org> Signed-off-by: Christoffer Dall <cdall@linaro.org>
(backported from commit 15d2bffdde6268883647c6112970f74d3e1af651)
[ dannf: trivial context fixes ] Signed-off-by: dann frazier <dann.frazier@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Marc Zyngier [Tue, 2 May 2017 13:30:37 +0000 (14:30 +0100)]
arm64: KVM: Do not use stack-protector to compile EL2 code
BugLink: https://bugs.launchpad.net/bugs/1673564
We like living dangerously. Nothing explicitely forbids stack-protector
to be used in the EL2 code, while distributions routinely compile their
kernel with it. We're just lucky that no code actually triggers the
instrumentation.
Let's not try our luck for much longer, and disable stack-protector
for code living at EL2.
Cc: stable@vger.kernel.org Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Acked-by: Christoffer Dall <cdall@linaro.org> Signed-off-by: Christoffer Dall <cdall@linaro.org>
(cherry picked from commit cde13b5dad60471886a3bccb4f4134c647c4a9dc)
[ dannf: This fixes a KVM panic() exposed by the remainder of the series ] Signed-off-by: dann frazier <dann.frazier@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Vijaya Kumar K [Thu, 26 Jan 2017 14:20:49 +0000 (19:50 +0530)]
irqchip/gic-v3: Add missing system register definitions
BugLink: https://bugs.launchpad.net/bugs/1673564
Define register definitions for ICH_VMCR_EL2, ICC_CTLR_EL1 and
ICH_VTR_EL2, ICC_BPR0_EL1, ICC_BPR1_EL1 registers.
Signed-off-by: Vijaya Kumar K <Vijaya.Kumar@cavium.com> Reviewed-by: Eric Auger <eric.auger@redhat.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: dann frazier <dann.frazier@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Bryant G. Ly [Fri, 2 Jun 2017 22:14:33 +0000 (17:14 -0500)]
ibmvscsis: Fix the incorrect req_lim_delta
The current code is not correctly calculating the req_lim_delta.
We want to make sure vscsi->credit is always incremented when
we do not send a response for the scsi op. Thus for the case where
there is a successfully aborted task we need to make sure the
vscsi->credit is incremented.
v2 - Moves the original location of the vscsi->credit increment
to a better spot. Since if we increment credit, the next command
we send back will have increased req_lim_delta. But we probably
shouldn't be doing that until the aborted cmd is actually released.
Otherwise the client will think that it can send a new command, and
we could find ourselves short of command elements. Not likely, but could
happen.
This patch depends on both:
commit 25e78531268e ("ibmvscsis: Do not send aborted task response")
commit 98883f1b5415 ("ibmvscsis: Clear left-over abort_cmd pointers")
BugLink: https://launchpad.net/bugs/1689365 Signed-off-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com> Reviewed-by: Michael Cyr <mikecyr@linux.vnet.ibm.com> Cc: <stable@vger.kernel.org> # v4.8+ Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
(cherry picked from commit 75dbf2d36f6b122ad3c1070fe4bf95f71bbff321) Signed-off-by: Manoj Iyer <manoj.iyer@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Bryant G. Ly [Fri, 2 Jun 2017 22:14:32 +0000 (17:14 -0500)]
ibmvscsis: Clear left-over abort_cmd pointers
With the addition of ibmvscsis->abort_cmd pointer within
commit 25e78531268e ("ibmvscsis: Do not send aborted task response"),
make sure to explicitly NULL these pointers when clearing
DELAY_SEND flag.
Do this for two cases, when getting the new new ibmvscsis
descriptor in ibmvscsis_get_free_cmd() and before posting
the response completion in ibmvscsis_send_messages().
BugLink: https://launchpad.net/bugs/1689365 Signed-off-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com> Reviewed-by: Michael Cyr <mikecyr@linux.vnet.ibm.com> Cc: <stable@vger.kernel.org> # v4.8+ Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
(cherry picked from commit 98883f1b5415ea9dce60d5178877d15f4faa10b8) Signed-off-by: Manoj Iyer <manoj.iyer@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Bryant G. Ly [Fri, 2 Jun 2017 22:14:31 +0000 (17:14 -0500)]
ibmvscsis: Do not send aborted task response
The driver is sending a response to the actual scsi op that was
aborted by an abort task TM, while LIO is sending a response to
the abort task TM.
ibmvscsis_tgt does not send the response to the client until
release_cmd time. The reason for this was because if we did it
at queue_status time, then the client would be free to reuse the
tag for that command, but we're still using the tag until the
command is released at release_cmd time, so we chose to delay
sending the response until then. That then caused this issue, because
release_cmd is always called, even if queue_status is not.
SCSI spec says that the initiator that sends the abort task
TM NEVER gets a response to the aborted op and with the current
code it will send a response. Thus this fix will remove that response
if the CMD_T_ABORTED && !CMD_T_TAS.
Another case with a small timing window is the case where if LIO sends a
TMR_DOES_NOT_EXIST, and the release_cmd callback is called for the TMR Abort
cmd before the release_cmd for the (attemped) aborted cmd, then we need to
ensure that we send the response for the (attempted) abort cmd to the client
before we send the response for the TMR Abort cmd.
BugLink: https://launchpad.net/bugs/1689365 Cc: <stable@vger.kernel.org> # v4.8+ Signed-off-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com> Signed-off-by: Michael Cyr <mikecyr@linux.vnet.ibm.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
(cherry picked from commit 25e78531268e9240fc594ce76587601b873d37c9) Signed-off-by: Manoj Iyer <manoj.iyer@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
This patch fixes a set of queue-full response handling
bugs, where outgoing responses are leaked when a fabric
driver is propagating non -EAGAIN or -ENOMEM errors
to target-core.
It introduces TRANSPORT_COMPLETE_QF_ERR state used to
signal when CHECK_CONDITION status should be generated,
when fabric driver ->write_pending(), ->queue_data_in(),
or ->queue_status() callbacks fail with non -EAGAIN or
-ENOMEM errors, and data-transfer should not be retried.
Note all fabric driver -EAGAIN and -ENOMEM errors are
still retried indefinately with associated data-transfer
callbacks, following existing queue-full logic.
Also fix two missing ->queue_status() queue-full cases
related to CMD_T_ABORTED w/ TAS status handling.
BugLink: https://launchpad.net/bugs/1689365 Reported-by: Potnuri Bharat Teja <bharat@chelsio.com> Reviewed-by: Potnuri Bharat Teja <bharat@chelsio.com> Tested-by: Potnuri Bharat Teja <bharat@chelsio.com> Cc: Potnuri Bharat Teja <bharat@chelsio.com> Reported-by: Steve Wise <swise@opengridcomputing.com> Cc: Steve Wise <swise@opengridcomputing.com> Cc: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
(cherry picked from commit fa7e25cf13a6d0b82b5ed1008246f44d42e8422c) Signed-off-by: Manoj Iyer <manoj.iyer@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Xiaofei Tan [Fri, 4 Aug 2017 19:50:26 +0000 (13:50 -0600)]
scsi: hisi_sas: optimise DMA slot memory
BugLink: https://bugs.launchpad.net/bugs/1708734
Currently we allocate 3 sets of DMA memories from separate pools for
each slot. This is inefficient in terms of memory usage
(buffers are less than 1 page in size, so we lose due to alignment),
and also time spent in doing 3 allocations + de-allocations per slot,
instead of 1.
To optimise, combine the 3 DMA buffers into a single buffer from a
single pool.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com> Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(backported from commit f557e32c0023ea0d67cdaa81b3398550dc1e4876) Signed-off-by: dann frazier <dann.frazier@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Seth Forshee <seth.forshee@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Xiang Chen [Fri, 4 Aug 2017 19:50:25 +0000 (13:50 -0600)]
scsi: hisi_sas: relocate sata_done_v2_hw()
BugLink: https://bugs.launchpad.net/bugs/1708734
Relocate get_ata_protocol() to a common location, as future hw versions
will require it. Also rename with "hisi_sas_" prefix for consistency.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com> Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(backported from commit 759040770dbc7c8c53aa23552d2d955e80c91ce6)
[ dannf: Included to simplify backport of following patch ] Signed-off-by: dann frazier <dann.frazier@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Seth Forshee <seth.forshee@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Xiang Chen [Fri, 4 Aug 2017 19:50:24 +0000 (13:50 -0600)]
scsi: hisi_sas: optimise the usage of hisi_hba.lock
BugLink: https://bugs.launchpad.net/bugs/1708734
Currently hisi_hba.lock is locked to deliver and receive a command
to/from any hw queue. This causes much contention at high data-rates.
To boost performance, lock on a per queue basis for sending and
receiving commands to/from hw.
Certain critical regions still need to be locked in the delivery and
completion stages with hisi_hba.lock.
New element hisi_sas_device.dq is added to store the delivery queue for
a device, so it does not need to be needlessly re-calculated for every
task.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com> Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit b1a49412f0aed757e7632f9276acdf2fb8f3832e) Signed-off-by: dann frazier <dann.frazier@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Seth Forshee <seth.forshee@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
John Garry [Fri, 4 Aug 2017 19:50:23 +0000 (13:50 -0600)]
scsi: hisi_sas: define hisi_sas_device.device_id as int
BugLink: https://bugs.launchpad.net/bugs/1708734
Currently hisi_sas_device.device_id is a u64. This can create a problem
in selecting the queue for a device, in that this code does a 64b
division on device id. For some 32b systems, 64b division is slow and
the lib reference must be explicitly included.
The device id does not need to be 64b in size, so, as a solution, just
make as an int.
Also, struct hisi_sas_device elements are re-ordered to improve packing
efficiency.
Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit ad6048325c7807818c6c49e485660143d97a622e) Signed-off-by: dann frazier <dann.frazier@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Seth Forshee <seth.forshee@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Xiang Chen [Fri, 4 Aug 2017 19:19:28 +0000 (13:19 -0600)]
scsi: hisi_sas: fix timeout check in hisi_sas_internal_task_abort()
BugLink: https://bugs.launchpad.net/bugs/1708730
We need to check for timeout before task status, or the task will be
mistook as completed internal abort command. Also add protection for
sas_task.task_state_flags in hisi_sas_tmf_timedout().
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com> Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit f64a6988268aae866bb6ce6edb910d454ccef331) Signed-off-by: dann frazier <dann.frazier@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Seth Forshee <seth.forshee@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Addresses-Coverity-ID: 1373843 Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com> Reviewed-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit eb045e046d5b2aab7710f82c2e5fb1403c69332b) Signed-off-by: dann frazier <dann.frazier@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Seth Forshee <seth.forshee@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Michael Ellerman [Wed, 19 Jul 2017 23:41:49 +0000 (18:41 -0500)]
powerpc/64: Fix HMI exception on LE with CONFIG_RELOCATABLE=y
Prior to commit 2337d207288f ("powerpc/64: CONFIG_RELOCATABLE support for hmi
interrupts"), the branch from hmi_exception_early() to hmi_exception_realmode()
was just a bl hmi_exception_realmode, which the linker would turn into a bl to
the local entry point of hmi_exception_realmode. This was broken when
CONFIG_RELOCATABLE=y because hmi_exception_realmode() is not in the low part of
the kernel text that is copied down to 0x0.
But in fixing that, we added a new bug on little endian kernels. Because the
branch is now a bctrl when CONFIG_RELOCATABLE=y, we branch to the global entry
point of hmi_exception_realmode(). The global entry point must be called with
r12 containing the address of hmi_exception_realmode(), because it uses that
value to calculate the TOC value (r2).
This may manifest as a checkstop, because we take a junk value from r12 which
came from HSRR1, add a small constant to it and then use that as the TOC
pointer. The HSRR1 value will have 0x9 as the top nibble, which puts it above
RAM and somewhere in MMIO space.
Fix it by changing the BRANCH_LINK_TO_FAR() macro to always use r12 to load the
label we're branching to. This means r12 will be setup correctly on LE, fixing
this bug, and r12 is also volatile across function calls on BE so it's a good
choice anyway.
BugLink: https://launchpad.net/bugs/1684054 Fixes: 2337d207288f ("powerpc/64: CONFIG_RELOCATABLE support for hmi interrupts") Reported-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com> Acked-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
(cherry picked from commit be5c5e843c4afa1c8397cb740b6032bd4142f32d) Signed-off-by: Manoj Iyer <manoj.iyer@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Colin King <colin.king@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Seth Forshee [Thu, 3 Aug 2017 21:10:15 +0000 (16:10 -0500)]
UBUNTU: [Config] CONFIG_SATA_HIGHBANK=y
BugLink: http://bugs.launchpad.net/bugs/1703430
This changed from y to m after trusty without justification.
Having it built as a module causes issues with booting on some
ARM systems.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Hanjun Guo [Wed, 2 Aug 2017 22:45:01 +0000 (16:45 -0600)]
ACPI / APD: Add clock frequency for Hisilicon Hip07/08 I2C controller
BugLink: https://bugs.launchpad.net/bugs/1708293
I2C clock frequency of Designware ip for Hisilicon Hip07 is 200M,
but 250M for Hip08, use two ACPI IDs to differentiate them.
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org> Reviewed-by: Kefeng Wang <wangkefeng.wang@huawei.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
(cherry picked from commit 6e14cf361a0cf3bbe0026557427a7eb2f64d3157) Signed-off-by: dann frazier <dann.frazier@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Seth Forshee <seth.forshee@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
BugLink: https://bugs.launchpad.net/bugs/1705586
The HP ZBook 15u G3 has a Conexant CX20724 with mute led on GPIO1 and
mic mute led on GPIO2.
Adding CXT_FIXUP_MUTE_LED_GPIO inspired on patch_realtek's one.
Signed-off-by: Jerónimo Borque <jeronimo@borque.com.ar> Signed-off-by: Takashi Iwai <tiwai@suse.de>
(backported from commit 5cd5b1bdfb0137d0e814a51ff203d72c76b9f375) Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Marcelo Cerri <marcelo.cerri@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
BugLink: https://bugs.launchpad.net/bugs/1704903
The current code only support DT method to control xge led.
This patch is the implementation of acpi method to control xge led.
Signed-off-by: LiuJian <liujian56@huawei.com> Reviewed-by: John Garry <john.garry@huawei.com> Reviewed-by: Yunsheng Lin <linyunsheng@huawei.com> Reviewed-by: Daode Huang <huangdaode@hisilicon.com> Signed-off-by: David S. Miller <davem@davemloft.net>
(backported from commit 1e4babee70a2e2d8f9e0da06f013563b0e26f654)
[ dannf: modified to work with acpi_evaluate_dsm() before it switched to
using a generic guid_t in 94116f8126de9762751fd92731581b73b56292e5 ] Signed-off-by: dann frazier <dann.frazier@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Seth Forshee <seth.forshee@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
projects / mirror_ubuntu-zesty-kernel.git / log